Search Documents

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

By Hendrix J. L, Nelson J. H

A study was conducted to examine how pretreatment of carbon-bearing gold ores with chlorine enhances gold recovery by cyanidation. It is hypothesized that metal species (including iron and copper) dissolved during chlorination adsorb on the carbon surface hindering the adsorption of dissolved gold. To test the hypothesis, samples of several sulfide minerals were subjected to reaction with sparged chlorine gas to determine which, if any, dissolve faster than gold under these conditions. Then, a synthetic carbonaceous refractory gold ore containing pyrite, chalcocite, activated carbon, and gold was subjected to gas sparging. The results of these experiments showed that chalcocite and arsenopyrite dissolve so that metal (copper and iron) is put into solution slightly faster than gold under the same chlorination conditions. Also, it was observed from the experiments that gold adsorbs on activated carbon during chlorination, but is replaced by copper and iron as the chlorination process dissolves more of the chalcocite and pyrite. The study concluded by investigating ferric chloride addition prior to chlorination to hinder gold adsorption on activated carbon.

Jan 1, 1991

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

Particles finer than 10 um often cause problems in flotation. The current under- standing of the nature of the following effects is discussed: slime coatings on particles, carrier flotation, increased froth stability, entrainment of ultrafine gangue, excess reagent consumption, slower rate of flotation, more reactive surfaces. The review emphasizes the principles underlying these effects rather than details of progress in practical solutions to the problems they cause. The princi- ples of selective flocculation and floc flotation and the various approaches to achieving selectivity are discussed. Hydrodynamic effects on floc growth are reviewed. The evidence suggests that satisfactory performance in the ultrafines fraction will be achieved only by simul- taneously increasing the rate of flotation of the ultrafine valuable mineral and de- creasing the rate of entrainment of ultra- fine gangue.

Jan 1, 1984

By Katsuyama K, Nag DK

Three aspects of rock mechanics, namely, in-situ stress estimation by acoustic emission (AE) method, strength of rock mass and role of chemicals to reduce the strength are covered. It is possible to detect the previously applied maximum stress by stressing a rock specimen to the point where there is a substantial increase in AE activity. This is known as Kaiser effect. From the AE signatures in the second and subsequent loadings, AE take-off point was identified more easily than in the first loading. In determining the compressive strength of rock mass, two factors have to be considered, namely, the size effect on the compressive strength of intact rock and the effect of discontinuities on the compressive strength of rock mass. Although a modified Bieniawski criterion gives best agreement with the triaxial test data, modifications have been suggested to Hoek-Brown criterion due to its popularity. It is possible to reduce the tensile strength of sandstone by saturating it with weak chemical solutions made with dodecyltrimethyl ammonium bromide, polyethylene oxide and aluminium chloride by up to 30%. In the case of compressive strength, there is no appreciable effect. The possible explanation is that the chemical solutions produce an effect on the strength of sandstone only when the failure mechanism is dominated by tensile mode.

Jan 1, 1998

By Gonzalez JM

The Pao gold prospect in N. Luzon, is an example of a high sulphidation epithermal gold system hosted in Mid-Tertiary alkaline volcanics, in the Philippine Arc. Styles of mineralization include: quartz-enargite veins, vuggy silica alteration bodies, and pervasive low grade (0.5ppm) gold mineralization, associated with kaolinite-pyrite-quartz alteration, and geochemically characterized by high As and Hg. Early magnetite-epidote-chlorite alteration linked to an unexposed granitoid is overprinted by an extensive zone of advanced argillic alteration (kaolinite-pyrite-quartz). No alunite is recorded. Important controls of mineralization include; a broad anticline intersected by axial faults, permeable pyroclastic units, and upward confinement of the alteration system by a highly impermeable, clay-rich volcanic unit. At this stratigraphic position the most important mineralization waz developed. The Pao high sulphidation system is not closely related to a stratovolcanic centre, and has formed subsequent to deformation of the volcanic field. It may, however, be related to an unexposed comagmatic intrusion.

Jan 1, 1990

By Stevens P

The Isa Mine of Mount Isa Mines Limited currently produces 5.4 million tonnes of copper ore and 3.3 million tonnes of silver, lead and zinc ore annually. Of this, 5.1 million tonnes of copper ore and 2.2 million tonnes of silver-lead-zinc ore is produced by sublevel open stoping. This paper summarises the capabilities, operating practices and problems encountered with current production drilling practices used to drill sublevel open stopes at Mount Isa.

Jan 1, 1982

High interest to basic-ultrabasic rocks is ex-plained by their specific, sutural, geotectonic po-sition and by deep level of generation of ultraba-sic magmas. These two factors allow us to treat this group of rocks as valuable source of informa-tion about the lower crust and upper mantle of the Earth. Basic-ultrabasic xenolith series is another source of information about the interior of the Earth. Detailed studies of the xenolith series give valuable material to geologists as to how endogenic deposits are fed and what is their source.Besides, the interest is explained by attempts to understand the relationship between basic-ultra-basic complexes and deposits of metalliferous and non-metalliferous mineral material.Absence of genetic boundaries in manifestation of metalliferous and non-metalliferous minerals, their temporal and spatial relationship allow us to treat the minerogenesis of ultrabasic complexes as a result of one ore-forming process manifested in Koryak-Kamchatsky, Sakhalin-Japanese, Ryukyu-Korean and Taiwan-Philippines island arc systems which re-present, in the opinion of the authors, one eastern Asian chain of the Pacific ore belt (Radkevich, 11)87).

Jan 1, 1990

This paper will discuss specifically the performances of vibrating screens having circular motion with inclined decks and linear motion with horizontal or near horizontal decks and both related mainly to coal, metalliferous, and other granulated solids applications where screening and efficient classification is required. Some misconceptions have been applied in the past with regard to making a screen type selection using either circular throw or linear throw and therefore this paper will endeavour to clarify these misconceptions.

Jan 1, 1984

By Smart RST C, Johnson NW, Ralston J, Griffin LF

At the Copper Concentrator of Mount Isa Mines, the largest diluent of the copper concentrate is liberated fine pyrite. Laboratory flotation tests carried out as a function of grind and flotation Eh in combination with surface analysis by X-ray photoelectron spectroscopy (XPS) have identified the major mechanisms of iron sulphide flotation. It was found that a significant proportion of the iron sulphide minerals had surface coverages of graphitic carbon, sufficient to impart moderate hydrophobicity in the absence of collector. A smaller, but economically significant proportion of chalcopyrite was also affected by the graphitic carbon coating. Two methods were tested to reduce the impact of the natural floatability of the iron sulphides on concentrate grades. 1. Depression through the use of organic depressants. 2. Preflotation to remove the "naturally hydrophobic" iron sulphides (flotation independant of Eh ) prior to chalcopyrite flotation. Preflotation was tested at the pilot plant scale. It was found that the amount of chalcopyrite reporting to the preflotation rougher concentrate could be minimised through flotation at a mildly reducing Eh by the use of nitrogen as the flotation gas to maintain the low Eh conditions resulting from grinding. The preflotation rougher concentrate was upgraded to an iron sulphide concentrate or a low grade copper concentrate.

Jan 1, 1991

By Bisshop J. P W

Maximum recovery of sulphide minerals by flotation is achieved over a limited size range. Valuable particles above and below this range have a smaller probability of being recovered. In the normal grinding-flotation operation, not all valuables are reduced to the optimum size range, and therefore sub- stantial losses occur. A significant improve- ment in the size distribution is not usually possible within the conventional circuit, and a more complex arrangement may be necessary to obtain optimum recovery of the valuable mineral. This problem is considered with refer- ence to the Mt. LyeZl concentrator. The performance of the existing circuit is dis- cussed, and it is shown that losses in recovery occur in both coarse and fine sizes. Laboratory tests indicate that regrinding the coarse particles results in an increase in recovery of up to 4%. Redistribution of plant grinding capacity to reduce initial grinding power by 6% and use this capacity to regrind coarse particles was considered. It is con- cluded that overall plant efficiency would be increased by 2% provided that overloading of the regrind mill could be avoided.

Jan 1, 1977

Most orebodies have one or more boundaries which are gradational, where the decision to stop mining is based on an economic cut-off. To maximise profit, this cut-off grade must be chosen correctly. It is necessary to review cut-off grades regularly, as the optimum cut-off grade changes with time, and major changes are hard to implement in a working mine without disruption to production schedules.Whenever a cut-off grade is used, there will be errors in its application caused by errors in the estimation of block grade. These can be minimised by stringent quality control in sampling and by the use of kriging, which attempts to minimise the absolute errors in grade estimation. The kriging method used should produce the most accurate estimates of marginal grade blocks - this will not necessarily be the technique that gives the best overall prediction of head grades.

Jan 1, 1993

The InLine Pressure Jig represents a breakthrough in digging technology Its design incorporates a unique combination of features previously utilised in conventional jig design. In particular, a moveable screen and circular bed are used to excellent effect. However, a major design innovation is the encapsulation of the circular bed within a vessel - allowing the equipment to operate under pressure. This innovation eliminates free water surface, improves the dynamics within the separation layer (crossflow) and provides significant cost savings in the handling of slurries. Recent research results have indicated its capacity to achieve high recoveries and upgrade ratios in the gravity separation of Minerals.

Jan 1, 1997

By Raudsepp R

Since 1991, the Porgera Joint Venture has processed refractory sulphide flotation concentrate by pressure oxidation with the subsequent gold recovery, from the washed residue, via a conventional leach/carbon-in- pulp (CIP) circuit. The capacity

Jan 1, 1997

The Mesozoic intrusive rocks in southeastern coastal China can be divided into three intrusive suites, and they can be brought into corresponding with four cycles of volcanic activity. This paper describes their time-space relation with volcanic rocks, and their geochemical characteristics. Data from the Mesozoic volcanic-intrusive. complex rocks in Eastern Zheijiang, Eastern Fujiang and Eastern Guangdong show distinct regional differences, both within and tectonomagmatic activity regions. The southeastern coast of China involves four tectonomagmatic activity regions. They have many differences on the nature of magma source regions, activity patterns of magma, time-space distribution, petrography and petrographic facies association of volcanic and intrusive rock and mineralization.

Jan 1, 1990

By White A. H, Vihena M. T M B

Presently, orebody modelling consists basically of fitting a mathematical model to represent spatially a certain geological variable, generally grade. An orebody model is constructed from a set of sample data obtained from various locations in the orebody, thus it is only one form of representation of the true phenomena. Checking the compatibility of the data with the modelling procedure is the most important factor when assessing confidence in the orebody model. The level of confidence in the model will depend on the adequacy of the data set and the validity of the basic assumption required by the modelling method. Fractal geometry is one way of modelling the spatial distribution of a geological variable in an orebody geometry. Fractals can be used to interpolate the Z(x) geological variable at unsampled sites. The concepts of self similarity and self affinity that form the basic assumption of fractal geometry theory which areinvestigated. The population distribution of the geological variable in question must be examined to determine the appropriateness of both fractal geometry and geostatistical modelling methods. The selection of the most appropriate method depends on the available data. A researcher or a practitioner needs to understand the strengths and limitations of the various modelling methods before choosing the most appropriate method. This study investigates the fractal properties of grade distribution using the variogram and some proposed variations as techniques to measure the fractalness. The aim is to assess applicability of fractal geometry theory to modelling ore grade distribution in a deposit. A comparison of the results demonstrates the methods which better capture the spatial behaviour of the variable under study.

Jan 1, 1995

By Sennitt C. M, Hartley J. S

The Twin Hills Gold Deposit is an example of a preserved, high level, epithermal system, with mineralisation introduced contemporaneous with deposition. The deposit is hosted within sediments of the Late Devonian to Early Carboniferous Saint Anns Formation, of Cycle 1 Drummond Basin stratigraphy, situated in central Queensland. Prior to epithermal activity in the Twin Hills region, a lacustrine fan delta depositional environment existed, together with minor tuffaceous activity. An and palaeo climate, with occasional periods of torrential rainfall, together with a basin with faulted margins, allowed alluvial fan prograda- tion. Cyclical repetitions of the fan indicate repeated faulting and seismic activity took place during deposition. Significant gold mineralisation was first intersected at Twin Hills by Metana Minerals NL in 1988, after drill testing a "blind" target outlined by geological mapping and bedrock geochemistry.

Jan 1, 1991

There are three major human resource management activities which, depending on how well they are done, impact on the performance of people and therefore the bottom line. These are: ò recruitment; ò training and development; and ò performance appraisal. Most sizeable organisations would say they are involved in all three, but there are many more that would admit that their human resource management practices are limited to recruitment. If we concentrate on the organisations that currently undertake all three, we have to ask, `Are they using different systems/benchmarks for each activity, or is there congruence between the activities?'. Our experience is that most organisations use different systems/benchmarks. The end result is: ò one set of criteria to recruit staff; ò another to identify their training needs; ò and yet another set of criteria to measure their staff's Performance.

Jan 1, 1995

By Ju Hao L, Jian L

A joint project between the Fan Kou Mine, the Guangzhou Research Institute of Non-ferrous Metals, the Julius Kruttschnitt Mineral Research Centre, and the Changsha Design and Research Institute of Non-ferrous Metals has implemented grinding control on a circuit consisting of two primary mills and a single secondary mill at the Fan Kou mine in northern Guangdong province, PR China. This paper describes the initial design of the control system and the changes made during its implementation. The initial design was to obtain maximum throughput at a constant product size. This was changed so that the control provided a constant product density at a set feed rate. The set feed rate is reduced when necessary to prevent overloading of critical components in the circuit. The reasons for the changes in the control strategy are discussed.

Jan 1, 1993

By P C. Pistorius

Previous mineralogical investigation of all effluent flotation streams of Mimosa mine (Zimbabwe) indicated that appreciable amounts of liberated platinum-group minerals (PGMs) of the Pt-Pd-Bi-Te class are not recovered û despite electrochemical measurements showing interaction between xanthate and such minerals. In this work, the flotation recovery of synthetically prepared Pd-Bi-Te was compared with that of chalcopyrite (a typical fast-floating mineral) and pyrrhotite (a typical slow-floating mineral), with microflotation tests. These indicated Pd-Bi-Te to be a fast-floater with flotation rates exceeding that of chalcopyrite. Predicted flotation rate constants (from the Ralston model) were significantly lower for small particles (with diameters similar to those lost to the effluent streams) compared with those of particle with intermediate sizes. This supports the suggestion that losses to effluent streams are caused by particle size effects.

Jan 1, 2005