Search Documents

By Fazakerley VW

The Murrin Murrin deposit is located about 210 km NNE of Kalgoorlie and 50 km E of Leonora in the North Eastern Goldfields region of Western Australia at latitude 28¦ 50'S. longitude 121¦ 54'E on the Laverton (SH 51-2) 1:250 000 map sheet. The tenements are held by Anaconda Nickel NL. Geological investigations between 1994 and 1996 resulted in resource calculations being completed for the ten lateritic nickel cobalt deposits shown in Figure 1. At a 0.8 per cent nickel cut-off the resources at May 1996 for the nine deposits are 116.8 Mt at 1.10 per cent nickel and 0.082 per cent cobalt. The nickel-cobalt mineralisation is contained in a laterite profile developed over Archaean serpentinised peridotites. A bankable feasibility study has been completed and the project is scheduled to be in production by the beginning of 1998.

Jan 1, 1996

By D B. Donato

Gold mining cyanide-bearing solutions can pose a risk, cause significant wildlife deaths and adverse public relations and result in non-compliance with regulatory conditions. The International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code) was developed as a voluntary code to encourage industry-wide improvements in managing cyanide responsibly. The Code requires design and implementation of robust monitoring programs for compliance under the following standards of practice: 4.1, 4.4 and 4.9. A robust monitoring regime can be complicated as each processing and tailing system is different. The following systems are commonly used in Australia: carbon-in-leach (CIL); carbon-in-pulp (CIP); heap leach process ponds; tailing waste disposal systems; peripheral discharge, central discharge and in-pit disposal. Some terrestrial wildlife can be denied access by fencing tailing storage facilities (TSFs) or other physical barriers, therefore limiting wildlife interaction with cyanide-bearing tailing and solutions to mainly birds and bats. While wildlife monitoring programs for processing and TSFs contain similar core attributes, it is necessary to adapt monitoring to take into account the site-specific features of each system. These core attributes are discussed in this paper, with reference made to cyanide concentration and associated methodologies. The issue is considerably complicated if tailing solutions are deemed or discovered to be toxic to wildlife. Essentially cyanides are required to be measured to gain an understanding of the concentrations to which wildlife may be exposed. This usually equates to measuring the cyanide concentration of solutions entering and leaving a tailing system. To assess the risk to wildlife presented by tailing and heap leach systems it is necessary to monitor both the hazard (cyanide concentrations) and the exposure (live wildlife species, presence and interaction). These tasks need not be arduous and a system of simple frequent monitoring has been developed and implemented for Code compliance. The wildlife monitoring developed by Donato Environmental Services (DES) and used at mining operations departs from the industry norm. It documents observer effort, live wildlife presence, habitat and behaviour in a tailing system, as well as deaths and carcasses. A greater understanding of wildlife cyanide toxicosis associated with this monitoring approach will enable mining companies to adopt a proactive approach to significantly reduce, or preferably eliminate, the impact on wildlife and assist in gaining Code compliance.

Jan 1, 2007

Solid EnergyÆs project evaluation process utilises a standard staged gate approach, with five levels leading ultimately to project execution (level 6). For a project to progress through each level, specific financial criteria need to be satisfied. Solid Energy primarily use value based (discounted cash flow) metrics to support investment decisions. Within this approach Solid Energy utilise a number risk-based techniques to quantify project uncertainty. This includes the use of risk-based probabilistic analysis using Monte Carlo simulation and probability-based scenario analysis. Figure 1 shows the net present value (NPV) cumulative probability. Project risks are identified through comprehensive risk workshops. The output of these workshops (list of key risks, ranges of uncertainty and probability of occurrence), is quantified within the financial models. Incorporating this risk information on a probabilistic basis allows an investment decision to be made with a robust knowledge of the range of possible project outcomes along with the likelihood (probability) of those outcomes occurring, for example 80 per cent confidence that the project value will be greater than NZ$10 M, 50 per cent confident it will be greater than NZ$50 M and ten per cent confident it will be greater than NZ$70 M. Incorporating risk implicitly into the financial analysis allows the business to easily evaluate/measure projects with different risk profiles. The detailed risk analysis does away with the complexity of arbitrary risk-based hurdle (discount) rates, as projects can be evaluated based on their specific risk characteristics. Whether a project will progress to the next level of investment and ultimately into implementation depends firstly on the value assessment in comparison with the associated risk/uncertainty, and secondly matching this with the businesses appetite for risk. At Solid Energy standard criteria are used for specific project evaluations, but in addition projects are considered on a portfolio or strategic basis also. Solid Energy attempts to maintain a mix of low risk (low value) projects with some high risk (high value) opportunities. The mix of projects must remain in line with the shareholdersÆ risk appetite. One of the keys to a successful investment decision is ensuring that the appropriate information is available to decision-makers so that they may proceed with a comprehensive understanding of the risks and impacts associated with the decision.

Jan 1, 2007

By C McMahon, S G. Walters

Mineral maps of æintactÆ and large particle textures have been produced routinely from optical microscope images. Polished thin sections of large particles (1 - 3 mm) provide a balance between representative sampling and the preservation of primary rock textures. Optical microscopy is an efficient way to generate mineral maps suitable for geometallurgical applications. The automated optical mineral identification was carried out using a Leica DM6000¬ microscope with a high precision stage suitable for direct tiling of image frames and good registration of multiple image layers. Standard images collected were 10 x 10 frames (20 mm x 16 mm). Four image layers were recorded: ætransmitted light plane polarisedÆ, ætransmitted light crossed polarsÆ, ætransmitted light crossed polars with 1l tint plateÆ and æreflected lightÆ. All image analysis was carried out using Definiens Professional V5¬. The four image bands were read directly in 12 greyscale bands. A segmentation algorithm produced objects based on homogeneity across all bands. These objects were then classified using a complex set of rules (Process Tree) that are based on image brightness in all 12 bands. Opaque and non-opaque minerals were classified in the same sample. Using this protocol up to 12 minerals can be satisfactorily classified in one sample. The opaque minerals were recognised using colour ratio and reflectance intensity in the reflected light image. Non-opaque minerals are more difficult because of the complex variable colours of many minerals and the complexity of interference colours. However, object-oriented classification using three transmitted light image layers and multiple rules is a powerful technique for recognition of these minerals.

Jan 1, 2008

By P Walton, L W. Armstrong, D P. Blair

Sydney is the capital city of NSW and has a population of approximately four million people. Eighty per cent of the cityÆs water is supplied by Warragamba Dam, which is situated some 75 kilometres south west of the city centre. A risk assessment was carried out on the dam and future predictions of water flows into the catchment area showed that there was a risk of a one in 700-year flood not being contained by the dam. The predicted loss of life and property damage warranted the construction of an auxiliary spillway on the eastern side of the existing dam to cater for any uncontrollable influx of water. A test blasting program was instigated and the blasting parameters were established that would lead to routine production blasting of the sandstone rock making it more cost effective to excavate. Blast induced vibrations were a concern to the owners and the dam wall and ancillary infrastructure was instrumented with sensitive vibration monitoring equipment during the test blasting phase of the operation. Once the blasting parameters were established from the testing program production blasting was carried out on a daily basis to maintain æstockpileÆ of fragmented ground for the excavation equipment. Blast vibration models were developed to predict vibration levels for more sensitive areas of the dam to give the operators more confidence in their operations. The blast induced vibration levels recorded did not cause any structural damage to the dam wall and the waveform frequencies of the blasting operation were much higher than that experienced during a recent earthquake. The integrity of the SCAÆs assets were at no time jeopardised.

Jan 1, 2001

The key elements required to maintain final wall integrity and hence slope reliability are discussed. Failure modes and mechanisms in highly structured rock slopes are then reviewed. The impact of blast disturbance on rock masses in general is discussed and the relationships between the slope failure mode and blast disturbance is then explored. The question of how designers can incorporate such impacts into the slope design process is then addressed. This necessarily involves rock mass strength consideration and two case studies are used to demonstrate a recent dilemma in this regard. Some progress regarding this dilemma has also been reported for the second case study. The major conclusions are that: Slope reliability can be severely compromised if the slopes are damaged by blasting and this impact is not often incorporated into the slope design process. The location and extent of the blast damage will impact some slope failure geometries and failure mechanisms more than others. The concept of failure mechanism specific vulnerability needs to be further developed. The evidence indicates that this aspect is even more extreme for weak ground conditions. The quantification of the reduction in rock mass strength due to blast damage is not well understood and limitations exist with some recent guidelines. The use of the Hoek-Brown criterion for slopes in blocky rock masses requires considerable judgement. Further applied developments in this regard would be very beneficial to the industry. Some promising methods to incorporate blast damage estimates into the slope design process are emerging. It is good business to minimise final wall blast damage otherwise a whole range of issues relating to reduced slope reliability emerge.

Jan 1, 1999

By Coskun B

The classification of selective mining units (SMU's) and the assignment of grades to those classified SMU's are very important in open pit mining, especially for precious metal mining. During ore control planning, the classification of mineral

Jan 1, 1998

By V S. Svinin, V V. Rybin, V A. Maltsev

In large-scale mining, large-sized intermediate pillars, or block-pillars, are generated on the horizon or between closely located mines. These pillars are mined under high rock pressure that results from the stress concentration zones superposition from closely located working excavations. This problem becomes much more complicated if high tectonic stresses occur in the rock mass inducing a rock-burst risk situation. Mining experience gained in mining seven block-pillars at three Khibiny mines in Russia under the geomechanical situation like that described aboveÆ is discussed in detail. It has been shown how safe mine of block-pillars depends on their width, location relative to significant geological failures and uncaved rocks of the hanging wall, the order of pillar recovery, and application of special measures for rock mass stress relieving. Basing on the analysis of the mining experience and special scientific researches, the basic principles are worked-out for safe block-pillar mining under rock-burst prone conditions.

Jan 1, 2000

By A E. C Peres, J D. Donda

With the aim of producing a concentrate with silica content lower than 1.0 per cent SiO2, laboratory experiments were conducted using a sample of the final concentrate from the Samarco iron ore flotation plant (mechanical cells circuit). The sample contained 3.08 per cent SiO2. This sample was split in two size ranges: >105 ¦m and 2. The >105 ¦m fraction, representing 23.3 per cent of the initial mass, was re-ground to 100 per cent 2 content were obtained. Considering the mass proportions of the two size fractions, the calculated silica content of the combined concentrate was 0.68 per cent, which is considered satisfactory for the objective of this investigation. The major reasons for the higher (0.90 per cent) silica content of the concentrate from the coarse fraction are the presence of silicon in the lattice of goethite and the presence of residual silicious slimes in the pores of porous hematite.

Jan 1, 2005

The Century zinc-lead orebody was discovered in 1990 and contains sufficient reserves to sustain open cut mining at 5 Mtpa of ore for approximately 20 years. It is proposed to pipe mineral concentrate in slurry form 300 km from the mine to the port of Karumba on the Gulf of Carpentaria. The concentrate will be dewatered at Karumba before being transported off-shore to deeper water in a self-unloading shuttle vessel for transfer to export bulk carriers. The four main environmental issues that attracted attention during the impact assessment phase of the project were: the selection of Karumba as the export port, the use of a pipeline to transport concentrate, the risk of concentrate spillage in the marine environment, and aquifer drawdown in the vicinity of the mine. This paper discusses these issues with emphasis on the context of the relationship between the Pasminco Century Project and Gulf communities. Environmental safeguards are discussed, including those that arose out of the negotiations regarding Aboriginal native title.

Jan 1, 1998

By S Servant, T J. Bidwell

Paste backfill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste backfill is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the backfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in situ measurement of paste backfill properties.

Jan 1, 1998

The relative importance of magmatic and metamorphic fluids in Archaean gold mineralisation has long been a subject of debate. Computer simulations can be used to explore the interaction between competing fluid flow drivers, thus providing insight into their role in mineralisation. This approach has been applied to Archaean gold mineralisation in the Yilgarn craton, Western Australia. A simple model representing regional metamorphism in a granite-greenstone terrane indicates that fluid produced during a regional metamorphic event in the Yilgarn was unlikely to have been involved in mineralisation, because it would have escaped from the crust long before the main gold event. Another model illustrates the competition between magmatic fluid production, convection, and deformation. The model shows that the timing of deformation relative to fluid production is important in determining the fate of magmatic and metamorphic fluids, and hence their potential to play a role in mineralisation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Yamakita T, Yoneoka Y

The Chigirishima Smelter of Toho,Zinc Co., Ltd. is the largest independent custom lead smelter in Japan and produces about 60,000 tonnes/yr of electrolytic lead. The quantity of slag produced by blast furnace is approximately 65,000 tonnes/yr, 30,000 tonnes/yr of which is sent back to the sintering plant for mixing with lead concentrates. The remaining slag used to be piled up at the yard until the operation of the fuming plant started in July 1977. We examined the slag fuming process with the purpose of achieving: 1) Improvement of the operating results by recovering zinc and lead from blast furnace slag. The lead content in slag at Chigirishima is slightly high, because the height of blast furnace shaft is low and consequently the quantity of sinter smelted per area at tuyere level is rather large. 2) Production of a salable slag as raw material for cement by lowering zinc and lead content in slag.

Jan 1, 1980

Separation in magnetic fluids is one of the modern techniques that offer a unique approach to material manipulation in a broad spectrum of industries. Its wide-scale application has been restricted so far for a variety of reasons, including limited throughput, inefficient recovery of magnetic fluids and the cost of commercially available magnetic fluids. This situation has changed recently. Very selective separators, with automated density control, capable of treating a variety of materials in a wide spectrum of densities and particle sizes have been built by DebTech and applied in the diamond industry. Technology for the recovery of magnetic fluids has been developed and low-cost magnetic fluids, with high magnetisation and low viscosity are being produced on a production scale. Scale-up of the technology has been addressed and units capable of treating large tonnages of material have been designed. Such a development thus offers the minerals industry a technology that surpasses the existing technologies in selectivity, efficiency and versatility

Jan 1, 2000

By Gee C. E

Ore reserves at the Kambalda Nickel Operations of Western Mining Corporation are estimated using the polygonal method for calculating areas of influence of drillholes. All raw assay and survey data are stored on one disk pack on the Company's CYBER 73 computer located in Perth, about 600 km from Kambalda. The initial step involving the computer is to search all assay data and calculate all potential ore-grade intersections. As the orebodies are thin, structurally complex and many are in close stratigraphic proximity, the selection of intersections which have the best grade over at least a minimum mining width involves complex logic. The orientation of an ore surface at each drill intersection point and a zone code are added to each intersection by the geologist from geological plans prepared for each ore surface. The orientation data together with downhole surveys enables the calculation of inter- section true widths and the zone code links each recalculated intersection to the appropriate ore surface.

Jan 1, 1977

During conventional eddy current separation, a repulsive force is applied to metallic particles by placing them in a rapidly changing magnetic field generated by a spinning magnetic rotor carrying an arrangement of alternate magnetic poles. This method works effectively for larger non-ferrous metallic objects, such as aluminium cans, but as the metallic particles become smaller, the bulk repulsive force on the particles is increasingly replaced by a rotational torque. Therefore, for small metallic particles it makes sense to use particle rotation, rather than particle repulsion, to effect a separation. Eddy current separators using particle rotation are similar in construction to present separators, but are designed to produce a rotating field of essentially constant angular velocity and field strength. Practical and economic particle rotation eddy current separations are possible down to particle sizes of about 200 ¦m, but separations, at probably uneconomic rates, can be carried out on particles as small as 50 ¦m.

Jan 1, 2000

With the recent wider introduction of friction hoists of the Koepe type. for winding from depths of more than 3000 feet it has been found that failure by fatigue is the most common form of rope deterioration. Large numbers of wire breaks occur near the centre of the rope cross-section and it is difficult to detect these with certainty using the preferred d.c. magnetic test. For best results with conventional search coils their dimen- sions should be related to the typical wire break field pattern surrounding the longitudionally magnetised rope. The field of a broken wire was experimentally determined, using a Polish type MD6 Defectograph wire rope testing magnet and a short prepared length of rope with a movable simulated broken wire. The external field distortion perpendicular to the rope was measured by means of a gaussmeter and Hall probe. The advantages of this method are that terrestial magnetism and inherent rope "noise" have no effect on the results.

Jan 1, 1971

A model of dense medium cyclones is developed based on balancing the terminal velocities of the discrete particles due to the centrifugal force against a random turbulent eddy velocity. An expression of the form P - or Q _ 1 100 e."A where P is the partition number., is a function of cyclone efficiency, particle size and density differential between the particle and medium, and is the slurry spilt, is developed and may be used for regressing plant partition data. The above model provides an understanding of peculiarities of the partition curve such as asymmetrical tails, elevation of the cutpoint and elevation of the d50 with increasingly fine feed. The effect of feed variables such as particle size, medium viscosity and changes in spigot or vortex finder diameter is shown. A means of convoluting the partition curve with various feed washabilities is discussed together with how the above may be used to evaluate plant performance for a variety of feeds.

Jan 1, 1987

The basic rule for correct design of a sample plant is that all parts of the material being sampled must have an equal probability of being collected and becoming part of the final sample for analysis. However, this rule is often ignored in the design of sample plants to save capital costs. This is false economy, because the samples taken are likely to be seriously biased and the precision may be compromised. The introduction of bias is particularly serious, because no amount of replicate sampling and analysis will reduce bias once it is present and it is often quite difficult and expensive to subsequently rectify the problem due to space limitations around the primary sampling location. This is also true of secondary and tertiary sampling stages, particularly in terms of the relationship between particle size and retained sample mass. The best strategy is to seek expert sampling advice and design the sample plant correctly at the outset.

Jan 1, 2005

Mount Isa Mines Limited has been mining copper ore for 50 years. In recent years, this production has been entirely by open stoping methods with cemented backfill, mostly in the large 1100 orebody.This has been the major ore source for 20 years, with smaller amounts coming from the 400, 500, 650 and 1900 orebodies. At present, the 1100 orebody is the only source, and this situation will continue until the deep 3000 and 3500 orebodies begin producing in late 1992/93. Production rates have increased to almost 6 Mt/yr, and are planned to rise to 7 Mt/yr by 1995/96. In the future, there will be a move towards variations of the open stoping system as production moves to more lensy zones of the southern 1100 orebody and to the deeper 3000 and 3500 orebodies. This paper describes current operations in the 1100 Orebody, with some indications of future directions.

Jan 1, 1993