Search Documents

IN the ordinary course of treatment of pyritic ores or concentrates, whether for the recovery of copper, tin, gold, or any other contents, the removal of some or all of the sulphur contents is almost invariably the first step. The practice is to roast the ore in a current of air so that the sulphur is oxidized to sulphur dioxide and the metal constituents are changed from sulphides to oxides. If it is feasible to produce sulphuric acid in conjunction with the treatment process, the sulphur can be usefully employed; but if this is not possible, then the sulphur contents not only become a dead loss, but tend to be a nuisance as well in the surrounding neighbourhood.The problem of avoiding this disadvantage and making economic use of the sulphur has had attention from the early days of scientific metallurgy, and in the past few years very special efforts have been made both to drive part of the sulphur as such from pyrites and recover it, and to replace the sulphur in the S02 by carbon, with the production of carbon dioxide and precipitation of the sulphur. So far economic success does not appear to have crowned these efforts. In the case of pyrites, of the two atoms of sulphur which go to make the FeS2, the first is very lightly held. Dissociation is effected by heat alone at a temperature which is given by Peters as 5160 C.Now, sulphur and hydrogen will unite or burn together, with the production of sulphuretted hydrogen. It occurred to the writer that, if hydrogen was passed over pyrites heated to the above temperature, this first atom would be snatched away by the hydrogen, and could possibly be economically recovered.The first step consisted of some simple laboratory experiments. From these it was found that this first atom was readily removed, and that the extraction was practically complete. Further, the reaction took place at a low temperature, a dull red heat being sufficient.

Jan 1, 1923

By S Prakash, P S. R Reddy, S K. Biswal, V N

The beneficiation potentials of two Indian iron ore slime samples by flotation technique using both cationic and anionic collectors are investigated. The direct and reverse flotation of slimes using oleic acid and dodecylamine as the collector have been studied using both conventional cell and flotation column to upgrade the iron content. The characterisation studies of iron ore slimes indicated that the samples are extremely fine in nature and contain substantial amounts of martite, magnetite, goethite, limonite, kaolinite and quartz beside hematite as the dominant iron mineral phase. The samples on average contain around 52 - 58 per cent Fe, four to seven per cent SiO2 and five to six per cent Al2O3. Taking into account the physico-chemical properties of the slimes, it is attributed that both the samples need to be deslimed by hydrocyclone before flotation. The results of both cell and column studies on sample I showed that a feed containing 57.5 per cent Fe could be upgraded to 65.5 per cent Fe at 50 per cent overall recovery with simultaneous decrease in SiO2 and Al2O3 content to 2.3 per cent and 1.8 per cent respectively by using oleic acid as the collector. In the case of sample II, it has been established that reverse flotation of silica is the better technique to improve both the grade and recovery of iron. Batch flotation studies in cell indicated that a product with 63.1 per cent Fe could be obtained at 40.0 per cent yield with 63.6 per cent iron recovery by the combination of reagents such as gum acacia, sodium hexa meta phosphate and dodecylamine. The performance of column flotation techniques is far superior to that of the cell with respect to both grade and recovery. The concentrates are found to be quite suitable for commercial exploitation as pellet feed.

Jan 1, 2005

By M P. Schwarz

This paper describes modelling studies of the flotation cells used by BHP Billiton Nickel West Ltd in the slimes circuit at Mt Keith. The aim is to achieve a better understanding of the hydrodynamic limitations in the existing cells to improve nickel recovery. Computational fluid dynamics (CFD) simulations have been performed on the 100 m3 mechanically-stirred cells. The data produced by the simulations include velocity vectors, gas holdup distribution, solids distribution, bubble size, superficial gas velocity and turbulent parameters. These results have been checked and found to match hydrodynamic measurements at the plant. An analysis of the data found that one of the limitations in fine particle recovery was related to the air bubbles discharged with the tailing. The air in the discharge was caused by the high viscosity of the pulp. In the presence of fine particles, the pulp exhibits high viscosity with a yield stress. The increased drag due to high viscosity caused the bubbles to rise more slowly up the cell. This results in a significant hold-up of bubbles, some of which report to the tailing with associated loss of valuable minerals. A parametric CFD study of the operating variables shows that less air would be discharged in the tailing by decreasing the following: air flow rate,pulp density,stirring speed, andfrother addition. Simulation results indicate that these changes would cause a lowering of the air hold up in the cell especially near the discharge area. Predictions of the bubble-particle attachment rates under various operating conditions have also been calculated. Although it is possible to increase attachment rates by increasing stirring speed or by increasing pulp density, the amount of air discharged and the amount of nickel loss through the tailing will also increase. The project showed that CFD modelling is a powerful tool for studying hydrodynamic effects of bubble-particle interactions in flotation cells.

Jan 1, 2008

By Shrivastava P

The iron orebodies of the Pilbara region are formed by supergene enrichment of banded iron formation and rarely do such processes produce orebodies with uniform grade distrib- utions. The orebodies being mined or developed have to be worked to grade/quality constraints imposed by contractual agreement rather than natural characteristics. Hence it is imperative to use a non-biased ore reserve calculation method. The geostatistical study of a typical iron orebody is presented. Emphasised are the geological characteristics of the orebody manifested as a variable grade distribution of iron and impurities; the determination of variogram model; subsequent uses of the model for computation of ore reserves and kriged lock estimates; computation of dispersion variance and conditional simulation of orebody.

Jan 1, 1977

The necessity for good management and economic working in our mines and ore-dressing sheds is impressed upon us by the present low prices of all our metals. Silver, lead, copper, and tin have all suffered a heavy decline during the last six or twelve months, and many mines have been shut down simply on account of the low market value of the ore produced. After fully considering the position of the mining industry. I am convinced that considerable improvements will have to be made to make it as prosperous as it ought to be. The most obvious of these improvements are good management, good machinery, and as little interference by directors as possible. If these conditions are insisted upon and carried out efficielltly a poor mine may have a chance to weather the storm.There is no doubt that the present depression is the refilult of over-speculation and general loss of confidence by which the whole commercial system has been affected, and every branch has suffered more or less, mining not excepted. It has suffered heavy losses in the past, and the future is not over bright we are, therefore, compelled to be careful in everything by which mining is affected and savings can be secured.

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

By R West

The Olympic Dam smelter facility processes copper concentrate feed using direct-to-blister smelting technology to support the current site production rate of 225 000 t/a copper. The metallurgical control of the Olympic Dam smelter is largely managed from a single central control room. Control room operation and management is therefore a key function in ensuring safe and reliable operation of the smelter, including identifying and initiating control of abnormal events. As part of a consolidated smelter reliability improvement program, a team consisting of process and control system engineers was formed. The teamÆs charter was to address and resolve the alarm flooding issues being faced by the control room technicians and the lack of an up-to-date base of supporting functional documentation. The project was successfully resourced with WorleyParsons metallurgists, Citect PLC technicians and the on-site technical team. Implementation was conducted over a 12 month period with the goal of achieving best practice alarm levels. The goal was achieved through a systematic process of alarm design review that analysed every configured alarm versus best practice design standards. Innovative concepts such as group-based alarms, first-up interlock displays, graphic only alarming, alarm help and alarm shelving were developed and implemented in conjunction with improved alarm masking. Total configured alarms were reduced from 20 000 to 5000 while the alarm rates were reduced from in excess of 200 alarms per hour per controlling technician to best practice levels of less than 12 alarms per hour per controlling technician. Completion of this program has provided a firm foundation for implementing further control optimisation and was a key activity in supporting sustained smelter reliability levels.

Jan 1, 2005

By Fourney W. L, Weaver T. A

A large number of single borehole crater-forming shots were analyzed in terms of correlating the crater parameters with explosive weight. The objective was to determine a scaling rule for which the explosive weights varies over many orders of magnitude and covers many different geologic materials. Included in the data base are type and weight of the explosive, geologic medium and degree of saturation, charge depth-of-burial, crater dimensions, and crater rim (lip) measurements. An alternative scheme to the usual plot of scaled depth-of-burial versus scaled volume removed was desired. The proposed technique uses a plot of the logarithm of the explosive weight, Y, versus the logarithm of the slant length, R', calculated from the known depth-of-burial of the explosive and the measured crater radius. A plot of Log Y in kilotons versus Log R' in meters from all the crater tests in this data base resulted in a straight line with a of slope 0.31 and showed good correlation between the variables Log Y and Log R'. Since the crater data includes many geologic materials, different explosives (including nuclear tests), and large differences in charge weight, the straight line fit suggests that the type and strength of the geologic materials play a subordinate role to explosive energy in crater formation.\

Jan 1, 1990

By T Higuchi, T Yamamoto, K Takehara

Iron ore fines are used as raw materials for sintered ore for blast furnaces in the world. Since the production and quality of sintered ore have a great influence on the stable operation of a blast furnace, many technologies were developed for controlling the heat profile in the sintering machine, which largely affect the sintered ore properties. In particular, the influence of oxygen in the suction gas, which plays an important role in combustion, was investigated over the years. It is known that increasing the oxygen ratio by about 30 per cent not only significantly improves the combustion rate, but it also increases the strength and yield of sintered ore. However, the details of the mechanism for improving these qualities are unknown. In this study, we investigated the influence of oxygen enrichment at higher ratios (O2: 21–40 per cent) and tried to understand the sintering behaviour enhanced by oxygen. The effect of oxygen enrichment on sintered ore quality and the heat profile were evaluated by sintering tests using a quartz glass pot. From the results, sintered ore yield had a maximum value for O2 = 30 per cent, but strength was increased for O2 = 40 per cent. From heat pattern analysis, it is clear that the high temperature holding time also reached a maximum at O2 = 30 per cent. Furthermore, we found that with increased oxygen ratio, the combustion speed (flame front speed) was increased, but the area of combustion was enlarged. It is considered that there could be a maximum oxygen ratio value for the yield from the balance of these positive and negative effects on high temperature holding time. To clarify the reason for strength improvement, thermodynamic calculations were performed and it was found that melting behaviour could be improved by changing the oxygen ratio.

Sep 18, 2023

By C Yeung, N Swa, D Gribble, R Reupana

BlastLiteÖ is a low density explosive developed by Dyno Nobel and has been in use at BHP Billiton Iron OreÆs Mt Whaleback Operation since March 2004. The Mt Whaleback Operation utilises BlastLite because it offers an attractive alternative to ANFO in soft to medium strength rock types. Its use also reduces the amount of liquid fuel oil consumed and is well aligned with BHP BillitonÆs corporate Energy Excellence initiatives to reduce greenhouse gas emissions. This paper presents the:results of characterisation work completed on-site as a fourth year mining engineering thesis, and application and benefits of the product at Mt Whaleback. One of the key features of low density products is that the detonation is non-ideal. That is, the explosive does not react fully in the detonation driving zone. This manifests itself in that the product is highly dependent on charge diameter and confinement conditions. Dyno Nobel has access to the Vixen suite of detonation codes for characterising the ideal and non-ideal behaviour of explosives. The objectives of this work were to use the Vixen_i code to characterise the detonation performance of BlastLite, in order to understand the role of the bulking agent and to allow modelling of the explosive. The detonation performance was established by detonating a series of unconfined charges at various diameters and measuring the velocity of detonation (VoD). The work program consisted of sourcing and preparing cardboard tubes of various diameters (80 mm to 305 mm). The tubes were loaded with explosive at the BHP Billiton Iron Ore Mt Whaleback test range and detonated one at a time. Over the past three years BlastLite has been used in various applications across the site. Initial findings illustrate that shovel productivity from BlastLite shots was comparable to the baseline ANFO blasts. The study results were also backed with visual inspection and feedback from shovel operators. A work program is currently in place to develop different blends of BlastLite and TITAN« BlastLite to tailor the explosives to various blasting applications. The trials at Mt Whaleback are leading to future opportunities of BHP BillitonÆs satellite orebodies.

Jan 1, 2007

Mine planning studies of iron ore deposits are often based on resource models generated by ordinary kriging. Ordinary kriging aims for local accuracy to minimise the variance of expected estimation error but this is at the expense of reproducing variability of the original sampling data. Hence mine planning studies using kriged models are likely to underestimate product variability, and the required blending and stockpiling capacity to reduce variability to an acceptable level. Instead, conditional simulation models of the main chemical variables in iron ore are able to reproduce likely variability to be encountered during mining and processing. This approach is demonstrated in a case study of the Weld Range bedded iron ore deposit in Western Australia, with a comparison of ordinary kriging and conditional simulation models. Conditional simulation models suggest that, compared with the single ordinary kriging estimation, there is likely to be far greater block variability for iron and impurities, a greater requirement for stockpiling and blending capacity, highest variability in initial years of mining and less variability in later years of mining for deeper ore. The conditional simulations provide a more realistic range of mining outcomes for production of high-grade ore, which may be seven per cent less than in the kriged model, as well as for lower expected project net present value (NPV). In year one, the kriged model is conservative for NPV; however, in later years two to five the kriged model has higher NPV than most conditional simulations, suggesting expected NPV based on the kriged model may not be achieved. For improved decision-making in mine planning, a complete range of possible outcomes from conditional simulations of the deposit should be considered rather than relying on a single kriging estimation that may be an end member case in the range of possible mining outcomes.

Jan 1, 2009

In early 1985, Bougainville Copper Limited commissioned an automatic truck despatch system to control its fleet of 44 trucks and 9 shovels. Productivity gains in the past have been the result of increasing equipment size then improving availabilities. The emphasis now is on improving the use of that availability and in particular for trucks, in reducing non-productive truck movement. A batch allocation computer based truck control system had been in operation since 1978, so to achieve the desired improvements it was necessary to move to an automatic dynamic control system. A description of the system installed is given, together with a review of how the project was engineered, the problems encountered and the results achieved to Date.

Jan 1, 1986

By Olofsson O, Durance M-V, Villeneuve J

Modelling of the Sala Agitated Mill (SAM) using a simplified solution to the population balance approach has been carried out. The rate of breakage is modified by the mill power, providing predictions of the resulting product size distribution for different grinding conditions and mill sizes. The power of the mill is estimated by a physically derived function, using an assumption that the mill power consumption mainly arises from the ball to ball friction within the mill. The grinding efficiency, depending on the media ball size and pulp density is approximated in the model. Experimental work on grinding a complex sulphide ore using a pilot scale SAM 7.5 has been carried out. Good agreement has been found between the data from the test campaign and the simulated values. The model has also been validated with experimental data from a pilot grinding of calcium carbonate and from an industrial mill. The model is included in the USIM PAC simulation software.

Jan 1, 1995

By Davey KJ

Complex sulphide ores are characterised by complex texture of the valuable minerals. Any assessment of the performance of differential flotation circuits treating such ore should include analysis of the effects of poor liberation of the valuable minerals. Selected samples were taken from balanced size by size surveys of the flotation section of a concentrator treating an ore body containing fine grained galena and sphalerite in a matrix of iron sulphides which is mostly pyrite. liberation measurements were made using the QEM*SEM system on four or seven size fractions. The measurements indicated that less than 40 per cent of the galena and less than 60 per cent of the sphalerite in the flotation feed was liberated. The final concentrates were largely composed of composites of valuable minerals and iron sulphide however there was a small but significant fraction of liberated iron sulphide. Using the sized mineral flows obtained from the original balances and the liberation measurements, a satisfactory liberation balance was obtained. This enabled the effect of liberation on the flotation performance to be examined; not only for the entire circuit but also in the rougher, scavenger and cleaning sections. In the zinc circuit the effect of a regrind mill could be assessed. Recovery of galena in the lead circuit was limited by the recovery of composite lead particles. Recovery of liberated galena exceeded 95 per cent in all size fractions while the recovery of composite galena exceeded 85 per cent below 38 ¦m but fell sharply above 38 ¦m. Examination of the behaviour of the liberated and composite galena in the various sections of the lead flotation circuit revealed high recoveries of both liberated and composite galena particles in the roughing and scavenging sections but very low recoveries in the final two cleaning stages. Similar trends to those observed in the lead circuit applied in the zinc circuit although the performance of the liberated sphalerite also fell off at sizes greater than 38 pm in this case. Thus the zinc recovery was limited by the flotation of both the liberated and the composite sphalerite. The effect of regrinding was to increase the recovery of sphalerite mainly by reducing the amounts of sphalerite in less liberated sizes rather than by increasing the liberation of the sphalerite within a given size Fraction.

Jan 1, 1993

By Takagi T, Seetharam R, Sie SH, Naito K

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medical/high-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnSZ), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995

It is usually the case that the short-term plannerÆs role is occupied by the younger site mining engineer. ThatÆs because mine scheduling is generally seen as a mundane and thankless task. But, short-term planners play an extremely important role in maximising the value of the mining resource, generally the companyÆs biggest asset. A look at any mining operation today will expose the competing drivers behind the operational and strategic plans. Operations are too often faced with pushing short-term constraints. It is the responsibility of the short-term engineer to answer the question of æWhere to next?Æ. In answering this question the young mining engineer is in an environment overflowing with urgency and constraints. Hasty decisions made at this time may have significant adverse consequences to the long-term value of the resource. Long-term strategy must address a broad and expanding number of issues that are generally overlooked by the short-term planner. It takes a holistic, rather than the prescriptive approach of short-term planning to determine the best strategic direction for the operation. To better understand the consequences of decisions made at the operational level short-term planners need better vision of the whole business. The key to improving the mining business is a planning process that integrates the short-term planners role with the overall mining strategy. Future developments in the mine planning process will focus on bridging this ædisconnectÆ between the operational objectives and the long-term goals. Improvements will come from the tools which planning engineerÆs use, and the planning methodology surrounding them. There will be significant hardware improvements to improve the speed with which a short-term planner can evaluate plausible options. Software that maximises the use of the improved hardware will be developed. Complimenting these technological improvements, conceptual methodologies of mine planning will improve to allow strategic planning to be brought within the focus of the short-term planning engineer. In todayÆs mining industry the young mining engineer is embarking on a career where business processes are paramount. This paper discusses the ædisconnectÆ that occurs today between the operational planning and long-term strategy and how this is driving developments in mine planning today.

Jan 1, 2003

One common public perception of mining is that financially it is an extraordinarily risky business. Another and contrary view, in certain circles, is that price risk and other financial risks can be relatively easily removed or shifted by a number of schemes or devices. In reality, beyond the orebody discovery stage, mining need not be any more risky than most heavy industrial businesses. Nevertheless, as stated by Rappaport, (1986): Risk is a parameter of central importance in establishing the economic value of any asset. The level of risk is determined both by the nature of the firm's operations and by the relative proportions of debt and equity used to finance its investments. These two types of risk are commonly referred to as 'business risk' and 'financial risk' respectively. The term financial risk is used somewhat more loosely herein to recognise the reality that any risk inadequately addressed in the design, construction and operation of a mining project can have significant financial consequences; usually negative. For instance, a specific area of business risk in mining is often called technical risk which definitely has severe financial consequences if not managed correctly. The various risk shifting, hedging and risk management tools available all have their place and range from merely useful to almost indispensable. However, in the long-term, financial risks are maintained at acceptable levels by the application of sound, more fundamental business management principles. There are many with a vested interest in perpetuating a perception that the conceptual foundations of sound management practice are extremely complex. In reality, most management concepts are prosaic, but their application requires incredible discipline and hard work. There is no magic formula or 'silver bullet'. It appears that a company whose activities are restricted to mining can analyse the range of risks specific to mine development and operations more clearly than companies in which mining is just one of many businesses. The almost universal failure of large oil companies in the mining business is probably the best example of lack of any clear comprehension of fundamental business characteristics and risks. Conversely, in regard to risk management, choosing to be in other business as well as mining does nothing to reduce the risks of the mining business. The individual shareholder can probably make such 'diversification of portfolio' decisions better than most management teams. It could be argued that diversification across a number of disparate businesses may actually increase overall corporate risk due to lack of management concentration and focus. These differences between the perceptions of financial risks and the realities in mining need to be further elaborated in relation to some uncompromising business concepts.

Jan 1, 1994

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

By Woodcock JT, La Broody SR

As part of a project on the application of thiourea leaching to a variety of Australian ores, the systematic variation of pH, redox po- tential, and thiourea concentration were in- vestigated on an oxidized gold ore from the Nevoria mine, WA. Stirred open beaker tests were conducted with a pH-stat and Eh-stat system to automati- cally control pH and redox potential at selected values, while thiourea concentration was main- tained manually. Increasing the acidity of the leach liquor from pH 3.6 to pH 1, increased the gold extrac- tion from 37 per cent to over 90 per cent in S h, but there was only a limited improvement below pH 1.5. Silver extraction and thiourea consumption increased as the acidity was in- creased. Increasing the redox potential from 150 to 200 mV (i.e. potential of Pt electrode vs SCE) increased the initial rate of gold and silver extraction, but the effect on cumulative gold extraction by 5 h was slight. Thiourea consump- tion was greatly increased as the redox poten- tial was increased. An increase in thiourea concentration from 1.2 to 4.8 per cent increased the initial rates of gold and silver extraction, but, as for the change in Eh, the improvement in cumulative ex- traction by 5 h was marginal. Thiourea consump- tion increased with thiourea concentration.

Jan 1, 1984

By Eri G

Ok ledi Mining Limited underwent a major transition from radio based truck dispatching to computerized dispatching for its equip- ment fleet in October, 1996. Modular Mining's Computerized Dispatch System was selected based on reputation and superior customer support. Modular's dispatch system is a fleet management system that uses computer, data communication and global positioning sys- tem technology to produce automatic, optimized haul truck as- signments. Optimization is achieved by equally distributing trucks to shovels so that truck queuing and shovel idling times are mini- mized. Computer illiterate mine operations personnel had to overcome a rather steep learning curve to use the high technology equipment. fortunately the system was able to be configured to use bitmap

Jan 1, 1997