Search Documents

By Forssberg E

This paper presents the experimental results on the effects of slurry Theology on ultra-fine grinding by a stirred ball mill. The amount of dispersant, slurry density and the particle size were selected as the parameters. The viscosity of dolomite-water slurry was measured by rotational viscometers. It was found that by adding enough dispersant, the effect of particle size from 1 to 10 pm on the slurry theology could be eliminated, but a strong effect of slurry density (tested for a range of 65 to 75 wt per cent) remained. The use of dispersant transformed the slurry from Bingham plastic flow to dilatant flow, which reduced the yield stress to zero, but increased the viscosity at higher shear rates. During the milling process, the viscosity was stable. The yield stress, however, increased suddenly from zero after a certain milling time. The mill operation stopped at the point where the yield stress increased due to poor slurry fluidity. The milling efficiency was found to be higher at a lower amount of dispersant addition or a lower slurry density within the experimental limits.

Jan 1, 1993

Western Mining Corporation (WMC), managers of the Windarra Nickel Project, installed a raise-bored haulage shaft and underground crushing system at the Mt Windarra Nickel Mine in 1982. The system is the second of its type installed by WMC, the first being at the Otter Juan Mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limitations, and escalating costs of a deep decline mine.The Windarra haulage system required a single 3 m diameter vertical raise drill hole, 470 m deep and equipped for skip haulage. Two five tonne skips, in balance, hoist crushed ore and mullock to the surface, at a design rate of 200 tonne/hr, effectively reducing truck haulage leads by up to 50 per cent. The system is now fully operational and will enable the mine to achieve its maximum production rate.The raise-bored shaft system has been shown to be cost effective and would be used again in circumstances where raise drilling is applicable.

Jan 1, 1984

Ranger Uranium Mines Pty. Ltd. operates an open pit mine and ore treatment plant in the Northern Territory designed to produce 3 000 tonne/yr of U308 in yellowcake from 3 500 tonne/day of mill feed. The construction of this project was completed in 1981, 12 years after the discovery of the orebody. Wright-Davy, a Joint Venture of Wright Engineers and Davy McKee Pacific, were the Project Managers and Designers of the $270 million ore treatment plant and associated infrastructure. The project was designed in Sydney in -an office integrated with the Client, staffed by 35 key personnel drawn from Wright Engineers and Davy McKee, supplemented by personnel hired for the project. The peak Wright-Davy workforce in Sydney of 200 contained 113 design staff. The design principle of using the best practicable proven technology resulted in a plant which easily produces its design output using ore types outside the design criteria. The structuring of the project systems and industrial relations policies contributed to construction being completed within time and under budget. The plant was built without any major industrial dispute occurring and no dispute arose due to the uranium issue.

Jan 1, 1983

Uranium minerals were found in Australia as early as 1869, but it was not until the 1940's that a search specifically for uranium was begun. Instrument types and techniques used in early exploration are still used today, but have been developed into more sophisticated and portable types. Recent improvements in exploration have been the introduction of the gamma ray spectrometer, radon sampling and geochemical surveys. The environments of presently defined uranium deposits are predominantly sedimentary. Known deposits in igneous environments are usually small. The size of targets which are likely to provide economic deposits is of the order of 10,000 tons U308, producible at a cost of less than $10 per pound. Such targets are most likely to be in Precambrian sediments or in granitic masses. Recent exploration in Australia has included investigation of Precambrian sediments, Precambrian and Palaeozoic granites, Mesozoic and Tertiary sediments, Precambrian volcanic rocks and brecciated masses of unknown age. The origin and method of emplacement of uranium in these environments is not well known but there are indications that syngenetic sedimentary processes are important, and volcanic rocks may make a major contribution to the supply of uranium.

Jan 1, 1970

By Dawson RD

For the past 45 years, the casting of refined lead ingots by The Broken Hill Asso- ciated Smelters Pty. Ltd. (B.H.A,S,) at Port Pirie has been mainly by use of manually operated rotary casting wheels of Newnam design. This style of operation was quite satisfactory as far as standard of product was concerned, but was manually intensive and a relatively high cost operation. With most other large scale lead producers already using automated-casting equipment, an investigation which commenced in 1966, progressed through stages of enquiry, design and development until the present plant commenced trial operations in late 1973, and fully operative in late 1974. While certain features of the plant are sed on overseas practices the plant was signed and built within Australia to BRAS ecifications. As constructed it consists two almost identical casting lines each pable of producing 25 kg ingots at 25 tonnes r hour using straight line casting machines d automated stacking weighing and strapping

Jan 1, 1975

Both innovation and excellence are desirable attributes of education, as they are also markers in the progression of the human race, but how attainable are they? The interaction of minerals and humanity provides a special insight into the development of both criteria, from the discovery that chert cuts, through the Bronze Age and the first use of metal alloys for implements, to using coal, oil and uranium as sources of fuel. However, there have been many hiccups along the way, where excellence in one respect has meant disaster in another. Examples are in the exploitation of asbestos, and in traditionally poor work practices in mining, both contributing to the widespread public belief that minerals and mining are ecologically undesirable. Yet is this perception based on the unrealistic expectation of innovation and excellence being simultaneous qualities of any given process? Common sense born of experience indicates that the journey from one, to the other, is usually a long and often tedious process, with much trial and error before excellence is attained. In our time, the partnership between academia and industry is the usual pathway to achieve it. Even so, we should take care that innovation does not become overwhelmed by the pursuit of excellence: as history clearly demonstrates, humanity depends upon both.

Jan 1, 2004

By E J. Gardiner, C M. Hogan

Acidic drainage has long been recognised as the largest environmental liability facing the mining industry, and to a lesser extent, the public, through abandoned mines. The Canadian Mine Environment Neutral Drainage (MEND) initiative was the first international multi-stakeholder program to develop scientifically based technologies to reduce the effect of acidic drainage. The original MEND Program extended over a nine-year time frame ending in 1997, with technology transfer activities continuing to the end of year 2000 under the MEND 2000 program. Both programs have contributed enormously to the understanding of acidic drainage and how to prevent it. MEND3, launched in 2001, intends to further this effort with a strong, research-driven program. The successes of the MEND initiative have come through the collaborative efforts of the partners, the sharing of experiences, the thorough evaluation of technologies and their incremental improvements. As a result, the knowledge base on acidic drainage has grown considerably. An international model of alliance between the various worldwide initiative involved in acidic drainage is being formalised at this conference. This global alliance will enhance technology transfer capabilities and will lead to improved environmental performance for the industry. It is through collaboration that we have achieved the most progress in environmental performance, and this formal relationship will further expand these benefits.

Jan 1, 2003

THE Great Fitzroy Mines Limited, comprising an area of 183 acres, and held under lease, are situated at Mt. Chalmers, within the Cawarral goldfield, 18 miles from the city of Rockhampton, Queensland, on the Rockhampton-Yeppoon railway.The nearest railway station i; Mt. Ohalmers, distant about half a mile from the mine, with which it is connected by a fairly good road. The outcrop of the ore-body consists almost entirely of ironstained quartzite, no sign of copper being visible. The outcrop and its immediate vicinity have been worked intermittently for gold during the past :fifty years, the ore being amenable to battery treatment.About twenty years ago a company was formed to prospect this outcrop, and work was commenced by driving an adit, but the results proved disappointing, and work ceased. Later a party of prospectors sunk a winze from the adit level, which has sincedeveloped into wh~t is now known as the North shaft. The property was afterwards prospected by Messrs. Oharley and Osborne, who continued sinking the winze, meeting with sulphides at a depth of about 120 ft.The Mt. Chalmers Copper Mining Company was formed to work the property, and smelting operations started on a small scale. These, however, met with ip.different success, and the property was again abandoned.

Jan 1, 1911

By Quinn P, Robertson G, Agar GE

The replacement of diphenylguanidine (DPG) for separating INCO Bessemer matte with a water soluble collector requires a frother since most collectors do not have frothing properties. The objective of this study was to identify a non persistent frother which produced a deep froth and collapsed rapidly, while maintaining acceptable metallurgical separation. Incremental rougher flotation tests failed to differentiate any metallurgical benefit through the use of a specific frother, so other tests were employed to identify the candidate frother. The equilibrium froth height and rate of froth collapse (froth stability) of several commercial frothers were evaluated as a function of frother concentration using a 'frothmeter' apparatus. Frothers evaluated were methyl isobutyl carbinol (MIBC), Pine Oil, triethoxy butane, Dowfroth SA1263, Dowfroth 250C, Dowfroth 200 and Allied Colloids CRNI-1002. Dowfroth SA1263 produced the largest froth height, and TEB had the greatest rate of froth collapse. Frothers with properties similar to Dowfroth SA1263 and Dowfroth 250 were rejected due to their persistent froths. TEB was rejected because it has a low flash point and Pine Oil could be a nuisance to add to a flotation column. Therefore, the preferred frothers were declared to be Dowfroth 200 or Allied Colloids CRNl-1002.

Jan 1, 1993

Tyre cost at Mount Morgan Limited had been 24% of the truck operating cost. Comprehensive tyre testing resulted in a reduction in tyre costs of about one third. A record of the evaluation techniques may enable the selection of tyres that are most suited to particular conditions. Rubber characteristics, rubber quantity, tyre design, road conditions, dump conditions and inflation pressure were found to be sig- nificant variables. Measurements of tyre temperatures at the breaker strip were used to select the tyre design and inflation pressure required for Mount Morgan Limited's conditions. Relugging of tyres was discontinued as a result of tyre testing.

Jan 1, 1974

A feasibility study will fail its objective if it does not identify and then correctly assess, all the risks which could have a substantial impact on the financial viability of a project. Before this assessment can be undertaken, one needs to understand the risk profile of the entity which is making the decision about the project. Some of the commonly encountered issues when assessing project risk are related to the problem of not being able to see the wood for the trees. In any risk analysis it is important that conservatism does not strangle a viable project; that the variables are internally consistent with each other, that reality checks are carried out and that appropriate expertise is used. Sensitivity analysis forms a part of the overall project risk assessment; however, it can only test those variables which have already been identified in the financial model. The most useful tool in performing a sensitivity analysis is Monte Carlo simulation. When properly used, it provides a more real world scenario than the simple adjustment of key variables by ¦ 10 per cent one at a time. Monte Carlo can provide valuable information about the robustness of a project. Project risk and sensitivity assessment is prone to the analysis paralysis syndrome. The focus should be on quality rather than quantity.

Jan 1, 1997

Before proceeding to the main portion of the above subject, a few remarks as to the general question of our mill slimes seem called for, and, with this in view, it is intended to briefly refer to the salient, points connected with their production, treatment and disposal at the mills.It is well known that, owing to the inticate mixture of the constituents of our sulphide ore, 'a very great deal of crushing and grinding is required to detach the particles of galena from the zinc blende and gangue of the ore, and it will be readily understood that, in this operation, a considerable amount of the material is converted into a slime which consists of minute, but ,(as can be see~ under a glass) well definied particles of all the constituents· 6f the ore arid combinations thereof, the relative proportions of which depend on the dual characteristics of hardness and abundance of the different constituents. An analysis of the slime shows the contents to be as follows :-Galena (PbS)Blende (Zn S)Pyrites (Fe Sll)Ferric Oxide (Fell Os)Ferrous Oxide (Fe 0) contained in garnetsOxide of Manganese (Mn 0) contained in rhodonite and garnets

Jan 1, 1903

By Kolarczyk M

When controlling the ventilation process in a deep mine some knowledge of the sensitivity of the air volume output to changes in the resistances of network side branches is of great advantage.Sensitivity is taken to mean the limit of the differential quotient AV /ART where AV. is the change in air output in the i--h side branch caused by a change of resistance LI R in the r-th side branch. A method Is presen- ted for determining any arbitrary co- lumn of the sensitivity matrix. A network interpretation of this met- hod was developed in which an ancilla- ry network additional the basic network is constructed and solved, giving an analysis of the sensitivity signs de- pending on the structure of the network.

Jan 1, 1988

By Jaczkowski B. M, Cox T. J, Domfeh I. A, Stalker I

Mining and treatment of gold ore in the Ashanti region at Obuasi, Ghana has been continuous for more than 100 years. Earlier production from this world class deposit can be traced far into the history of West Africa's gold trade. As part of a general development and expansion program, Ashanti Goldfields Corporation (Ghana) recently undertook a program to heap leach oxidized near surface ore. Kappes, Cassiday & Associates was given a major role in the design, equipment supply, installation and start-up management of the 3000 tonne/day heap leach. Unusual conditions included a high annual rainfall and an ore which could be characterized as a soft, decomposed, water saturated schist. Production began in March 1990. Startup problems and their solutions are discussed.

Jan 1, 1991

The nickel refinery at Yabulu consumes an average of 118,000 kg/h of low pressure steam in stripping operations to-recover ammonia and carbon dioxide from product liquor and ore tailings streams. The steam used in the stripping operations is produced from the 25 MW power generation plant at the refinery. The back pressure on the non condensing steam turbines is maintained at 60 kPa.Studies have been carried out to determine the optimum amount of steam required to be generated for stripping operations. When steam production is increased, the product liquor flow from thewashing thickeners can be increased. This results in improved washing efficiency of the thickeners and therefore improves the plant nickel recovery. A computer thickener wash model was used to predict nickel recoveries at varying steam consumption rates.The studies have shown that in most plant situations, it is not economical to-generate more steam than that already available from existing power production.The studies also highlighted the necessity to use all steam generated from power production at all times to maintain maximum nickel recovery.

Jan 1, 1985

This is a brief introduction of a sewer pipeline constructed with a pipe jacking method in combination with a 1 200 mm finished inner diameter tunnel boring machine developed for the first time in Japan. The pipeline is located under a national highway running through a densely built urban area and is 185.7 m long and 2.9 m to 3.7 m deep from the ground surface. The geological features along the pipeline show mostly slate and partly silt. The pipeline was constructed with a newly developed multi-application type tunnel boring machine equiped with a fluid transport system. The construction consisted of tunneling by a tunnel boring machine followed by pipe jacking operations. The excavated materials were dis- charged off the tunnel by a fluid transport System.

Jan 1, 1987

This paper describes how Western Mining Corporation uses sophisticated diesel equipment in mining of shallow flat dipping narrow ore- bodies in the Otter Juan area. Though in most cases the stoping method chosen relies on hand held conventional equip- ment, the 'ore handling systems have been designed to allow for a relatively high degree of mechanization. The use of diesel loaders, trucks along with three boom jumbos is described. A single one in nine decline driven as the means of access to the various ore surfaces at Otter/Juan resulted in the first ore being produced first 15 weeks after the first round was fired in the Ore-Decline. Now, three years later, the.mine is in full production, and in 1971/72 produced 392,000 dry tonnes of high grade Nickel Ore.

Jan 1, 1973

This paper discusses a number of examples of how environmental factors have been incorporated into the water management aspects of mining projects. One example is the Kingston Lignite Project in the South-East of South Australia where the most significant environmental issue was considered to be the effect of drawdown from mine dewatering and depressurization upon the use of groundwater. By proposing an alternative mining method - the use of floating dredges rather than a two-pass dragline method - drawdown effects would no longer be a concern. A second example is the Pine Creek Gold Mine in the Northern Territory. In this case the principal area of interest from an environmental viewpoint was water management - in particular effluent disposal, contaminated seepage from overburden and tailings, and project water supply. Through an integrated approach to the management of wastes and water the potential for water quality impairment was significantly reduced and external water supply requirements were also significantly reduced.

Jan 1, 1987

By A Ruotsalainen

Mining industry sees a comprehensive future in optimisation and process control. High resource utilisation is a starting platform when lower operational costs with higher rate of return are the target. Simulation is quickly penetrating the mining industry as a planning tool. A discrete event simulation helps to visualise the reality of a mine and the various mining processes, which typically include a fair degree of complexity. What-if scenarios can help to determine the impact of occurring changes to production. Understanding of critical points in the layout and resource allocation at an early stage can help to optimise the material flow. The obtained information may then be used as proposal or confirmation of the system applicability and economy. Simulation is a way to fine-tune and optimise the resources within. It helps to predict system sensitivity to various aspects. Although simulation today is used typically in a feasibility stage, there is an opportunity to continue using simulation for further process enhancement. In the future simulation will without doubt be used increasingly as a dynamic simulation and continuous improvement tool. This paper discusses the use of OptimineÖ simulation tool in resource optimisation. Some examples describe the way the tool operates and how it helps to view the technology, mine layout and operational data.

Jan 1, 2003

By P Gardner

The Kanowna Belle gold mine in Western Australia has reached a depth of 1000 m on the way to 1300 m. A feasibility study undertaken in 2006 identified the mining of E-Block as both technically and commercially feasible. One of the major risks identified in the study was the ventilation capacity, as the existing primary ventilation system would not support the production schedule for mining and a major system upgrade would be required. Failure to provide the necessary airflow would put the project at risk. A review of the airflow requirements and infrastructure options detailed in the feasibility study was undertaken to ensure that the assumptions and design were optimised. This review recommended a minimum airflow of 206 m3/s, but by acknowledging the necessary constraints imposed by mining at depth and re-engineering the mine layout to optimise the primary ventilation circuit, this requirement was reduced to 160 m3/s. This represents a 22 per cent reduction in airflow and a reduction in capital cost that will see mining at depth become economically feasible at Kanowna Belle. This paper discusses the processes that led to a redesign of the mining layout and highlights the importance of including the ventilation network in the optimisation process.

Jan 1, 2008