Search Documents

By Gallet M, Watsford R. M S

The 1989 feasibility study of the chessy, france, copper, zinc, pyrite and barite orebody was based upon a classical flowsheet. The flowsheet included, three stages of crushing, conventional rod and ball mill grinding in series, and sequential flotation of four products utilising conventional mechanical flotation cells. To improve the profitability of the project the partners commenced a search for ways to reduce the projected capital and operating costs of the proposed development. This paper presents the improvements in the projected capital and operating costs as a result of design and concept changes. The major changes included: ò the simplification of the crushing section with the adoption of semi autogenous grinding (SAG) milling of primary crushed ore. ò the deferral of pyrite and barite flotation circuits until market conditions were positive. ò the simplification of the flotation circuit by the use of column flotation cells for combined rougher/cleaner duty. ò the purchase of second hand equipment. The result of these changes was to reduce the capital cost estimate of the plant from US$ 21 million to US$ 11 million and operating cost estimates from US$ 18.90 to US$ 13.60 per tonne of ore for a decrease of approximately ten per cent in potential revenues.

Jan 1, 1991

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

By Lin C, Jiaxiang D

A series of experiments were carried out with Hallimond tube in order to test the effects of different reagents. A good result has been obtained when potassium-n-butyl xanthate is used as collector for molybdenite and graphite complex are depressed by the depressor mixed with nigrosine and iron (III) chloride. The separating mechanism has been studied with help of many modem instruments.

Jan 1, 1993

In his introductory remarks Mr. MacKellar referred to three types of development which may be considered to compete with mining for land use. 1. Total Development - in which he cited urban development, and intensive agriculture. 2. Partial development - in which he cited pastoral, and in this category would come National Parks. 3. Non development - in which category would fall the primitive or wilderness areas.

Jan 1, 1971

By A F. Idziak

The aim of the present study was an application of coal optical property measurements for analysis of paleostress field existing in fault zones of the Upper Silesian Coal Basin (USCB) during the coalification of organic matter. Measurements of vitrinite reflectance were carried out on coal samples taken near a hanging stope of the Klodnicki fault. Other samples had been taken in vicinity of the Krzyzowicki fault. The Klodnicki fault is one of the main tectonic discontinuities in the northern part of the USCB. It is postulated that its origin is related to the deep-rooted latitudinal discontinuity in crystalline basement of the basin. The Krzyzowicki fault is located in the western part of the USCB where fold tectonic style dominates. Vitrinite, one of the basic components of hard coal is generally considered as optically anisotropic material. Anisotropy of physical properties is induced mainly by stress, which arranges vitrinite structure. Vitrinite anisotropy can be described by an ellipsoidal model called reflectance indicating surface (RIS) which is a geometrical representation of the optical anisotropy tensor. The investigation of the RIS for vitrinite was carried out on coal samples. The apparent maximum and minimum reflectance values measured for a single vitrinite particle were plotted against corresponding bireflectance to construct the reflectance crossplot. Interpretation of this plot yielded the magnitudes of the RIS three principal axes. The data obtained point to differences in optical anisotropy of coal under the study. The coal samples taken from block tectonic zone near the Klodnicki fault had mean reflectance value of less than 0.80 per cent. Their anisotropy coefficients were about 0.1. Optical properties of coal changed from the biaxial positive in the western segment of the fault to the biaxial negative in its eastern part. It suggests that past tectonic stress was greater in the western part of the zone than in the eastern one. Coal originated from a fold tectonic zone at the vicinity of the Krzyzowicki fault has mean reflectance value much greater than from previous region (ÿ1.20 per cent). Its optical anisotropy coefficient is equal to about 0.07. It suggests that paleostress field was more isotropic. The presented study shows the usefulness of coal reflectance measurements in the analysis of paleostress field existing during coalification process.

Jan 1, 2003

Chairman Bob Dennis, Ministers Frank Walker and TonyMcGrady,ActingMayor Bob Moore, other distinguished guests, fellow delegates to this Carpentaria and Mount Isa Regional Development Forum.Firstly I would like to congratulate the North West Queensland Branch of the AusIMM, and particularly its Committee, on what has been a verysuccessful Forum by any measure and for their kind invitation to me to participate in this Forum.

Jan 1, 1993

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

During the past seven years silver recovery has been increased from 9 per cent to over 61 per cent. The changes in plant practiee which have led to this increase are described. Gold room clean-up procedure has been varied, so that half the additional silver is obtained as pure silver chloride, which.is converted to silver bullion for marketing.

Jan 1, 1964

Evaluation of tyre chains has been taking place at King Island Scheelite for several years. Results indicate that tyre life has been greatly improved in all cases. Good cost sav- ings are resulting on small loaders. The worth of chains is difficult to prove on larger loaders under the conditions at King Island Scheelite. However, the dramatic decrease in the number of punctures has convinced the Company that chains are worthwhile on some larger loaders.

Jan 1, 1977

Details are given of the excellent performance, outside Australia, of steel slag in road pavement surfacing. Laboratory tests and plant trials have shown Port Kembla BOF steel slag to be a material with properties suitable for producing asphaltic concrete which will maintain a high skid resistance in service under heavy traffic. The high density of steel slag is a factor which will result in a cartage cost penalty likely to restrict usage to close to its source.

Jan 1, 1979

By Tilyard P. A

Pasminco has tested a Valmet ES1 ceramic disc vacuum filter at its Broken Hill concentrators. On lead and, particularly, zinc concentrates at the ZC Mine the filter performed well but on North Mine lead concentrate problems were experienced with deposition on the disc, which resisted both ultrasonic and acid cleaning. A preliminary financial analysis showed that the application of the filter at the ZC concentrator was worth pursuing. Accordingly an ES30 machine has been hired for plant evaluation.

Jan 1, 1989

By Arbuthnot IM

It is the commonly held belief that, because the separation of liquids from solids takes place considerably faster in high rate thickeners than in conventional thickeners, high rate thickeners (HRT's) must use more flocculant than conventional thickeners. Data collected from a wide range of thickener users in Australasia and data presented in the literature is analysed. In addition, pilot plant data, with direct comparisons between HRT's and conventional thickeners, is presented. It is concluded that the flocculant consumption for both thickener types is in the same range.

Jan 1, 1991

By Ryan CG, Cousens DR, Suter GF, Griffin WL

A novel method utilizing PIXE with microbeams following fire-assay has been developed to determine PGE and Au at sub-ppm levels suitable for application in exploration. Analyses of the prills from the lead and silver fire-assay yield Pt, Pd and Au concentrations readily. NiS must be used as collector if the complete suite of PGE is required, but this method is not as Convenient.

Jan 1, 1989

Fluidised Bed Combustion technology has expanded since the first fluidised bed boiler steamed in 1974 with 58 companies currently supplying units. In Australia the market has been in small boilers and the goal of a limited attendance coal fired boiler has been achieved. On the world scene, the major incentive for development has been emission control with sulphur capture and low NOX. The potential of significant reduction in plant size is encouraging development of pressurised fluidised bed combustion.

Jan 1, 1987

By B Ilich, M Brad, R Brandli, E MarT

The Wirtgen surface miner was investigated for application to the Cloud Break iron ore deposit since it can selectively mine thin seams and there is no requirement for drilling and blasting or primary crushing as the surface miner cuts and breaks the rock to secondary cone crusher feed size. A physical metallurgical study of the surface miner run-of-mine (ROM) from Cloud Break was conducted to better understand the product size distribution, amount of -31.5 +6.3 mm lump produced, lump stability and physical metallurgical quality compared to conventional drill and blast techniques. Since the Cloud Break mine was not in production, the lump product from crushing and screening of surface miner ROM was compared with product simulations using traditional premining physical metallurgical processing techniques including drop testing of PQ diamond core. Drop test conditioning is widely used in the iron ore industry to simulate blasting, crushing and screening at the mine and subsequent product degradation during handling from mine to port to predict both the amount of lump product on ship and the size distribution of the fines and lump. The size distributions of surface miner ROM for hard, medium and friable ore types show very tight size distributions with very little above 100 - 150 mm, about 60 per cent of the distribution between 75 and 6.3 mm, with less below 1 mm compared to conventional drill and blast ROM. Crushing, screening and drop test conditioning of the surface miner ROM produced more lump in equivalent ore types compared to drill and blast techniques or their breakage simulation using PQ diamond core. The higher lump yield from the surface miner was also confirmed by pilot scale crushing of some 7400 t of surface miner ROM from the Cloud Break trial pit. The lump produced from surface miner ROM was quite stable and showed similar low degradation characteristics to lump simulated from drill and blasting techniques. Product size distribution simulations using conditioned crushed lump from 1 m diameter Bauer hole samples were found to compare well with processed PQ core samples and surface miner product from trial mining at Cloud Break. The Bauer sample method is therefore considered to be a very useful close simulation to actual lump production, although the lump yield is lower.

Jan 1, 2007

The Plant Control and Data Logging System for the Loy Yang Open Cut (LYOC) is part of a control and communications network designed to provide a high level of surveillance of open cut plant and facilitate the efficient co- ordination of operations and plant maintenance. The computer system selected utilises a central dual mini-computer and multiple microcomputer data transmission network ,linked to the plant controllers using distributed, microcomputer based remote data collectors or outstations. Several aspects of the computer system are outlined.

Jan 1, 1982

Following plant trials in 1972 Mount Lyell installed an AMDEL On Stream Analysis system for measuring copper and density on the flot- ation feed and final plant tailing streams, in August 1973. As a result of poor performance of the final tailing system these probes were changed over to the rougher tailing stream, back to the final tailing stream and finally to the final copper concentrate stream where the system is currently performing satisfact- orily. The history of the development of the system to its current operational status is Described.

Jan 1, 1978

From 1980 to February 1991 the Rosebery concentrator purchased ore from Aberfoyle's Que River Mine. Following the termination of the contract the concentrator reverted to treating Rosebery ore alone. Since that time it has become apparent that the circuit configuration employed was no longer optimum for zinc metallurgy. The circuit was designed to treat a difficult, slow floating sphalerite; however, the opposite was now found to be true. The sphalerite is fast floating and the circuit was cumbersome. During 1992 extensive circuit changes led to the provision of a simple open circuit flow sheet. The circuit is now easier for operators to understand and lends itself to improvements in process control. Middlings streams have been minimised, which produces a far more stable circuit. Significantly, it must be noted that the key to achieving potential results must lie in reducing variations within the process. A significant ore characterisation program has been undertaken, providing an insight into the metallurgical compatability of the ore to be mined. Using the information collected in this program, metallurgical recoveries and grades can now be predicted with a geater accuracy. Ore characterisation data suggests that an improvement from a 54 per cent zinc concentrate to a 57 per cent zinc concentrate should be achievable. By understanding the size-by-size mineral assemblage, a strategy for concentrate grade improvement has been developed. The requirements of the customer must in all cases determine the quality of the product. Pasminco is a fully-integrated zinc producer and as such significant gains can result by tailoring the concentrates to suit the Smelters.

Jan 1, 1993

By Chen B

In recent years great efforts have been made in the optimisation of ball mill operation. This paper describes a methodology developed for modelling and optimising the steady-state grinding process. Thirteen basic similarity numbers of the process are derived. Based on these similarity numbers, we build a group of mathematical models which give a full description of the relation between dependent and independent variables. The parameter estimation and multi-objective optimisation of the grinding process have been done using these models, and validated with experiments in a continuous laboratory-scale ball mill.

Jan 1, 1993

In recent years stricter requirements imposed variously by the Companies Acts, auditors and the Stock Exchanges have resulted in annual financial statements of mining companies becoming more detailed, informative and useful. Standards of reporting on ore reserves have not kept pace with the improvements in financial information disclosure, despite the fact that ore reserves are usually the most important asset of a mining company. The ore reserve reporting practices of fifteen leading Australian mining companies are analysed against important specific criteria. In terms of detailed and meaningful disclosure, there is scope for major improve- ments in annual ore reserve reporting Practices.

Jan 1, 1981