Search Documents

This paper examines the interplay between longwall support design/geometry features, operational controls and geological features on ground response. Experience from several investigations is used to demonstrate the influence of factors such as longwall support capacity and geometry, setting pressure, coal seam strength and stiffness, tip-to-face distance and hydraulic supply and control system parameters on longwall ground response. These factors are then used to outline the requirements on key controls such as retreat rate and cutting height and their influence on allowable roof convergence. The ground response curve concept as a means to provide graphical representation of longwall support and strata interaction processes is presented. The approach was developed to address the requirement for a practical longwall support evaluation and selection tool that can take account of support load influences such as changes in roof geology or cover depth. An example of the comparison between single pass longwall and top coal caving in a thick seam environment is given to demonstrate the influence of the various factors discussed.

Jan 1, 2005

By Chang JF

This paper describes the advance in shaft sinking technique in terms of a vast complex of equipment in the last decade, and mainly recommends some ad- vanced technology and a vast complex of equipment, such as smooth blasting, la- ser guiding, shot-crete lining and rock- bolting, hanging bracket ring for drills, large-capacity wall grab, tipping device, storage bunker, and automobile haulage et.al., finaly, author in detail repre- sents some successful applications of advanced shaft sinking technique in some mines as an example.

Jan 1, 1987

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

The laboratory-scale reduction of fixed beds of iron ore pellets has been investigated over a range of experimental conditions. The effects of reduction temperatures, gas compos- itions and flowrates on 1) the rate of reduction and 2) the physical properties of the metallized products after reduction are being studied as part of a general programme aimed at the evaluation of the use of gaseous reductants for the direct reduction of Australian iron ores. This paper deals primar- ily with the effects of temperature on the rate of reduction using a H2/CO gas mixture. The physical properties of the metallized products such as strength after reduction, abrasion resistance and porosity are presented as functions of the reducing temperature.

Jan 1, 1974

By D H. Bell

The potential for extracting gravel materials from active floodplain and channel areas has been investigated for three West Coast rivers û the Grey, Inangahua and Whataroa. Studies have focused primarily on resource availability and replenishment, but there are clearly also environmental management issues associated with such a proposal. The potential uses for of extracted materials include roading and concrete aggregates, as well as railway ballast, whilst a major benefit would be in assisting with flood control and channel maintenance in a naturally aggrading system. Sediment movement in the rivers has been examined at three scales; long-term (>100 years), medium-term (10 - 100 years) and short-term (<10 years). Long-term sediment movement is based on geological and geomorphological information, such as cyclic fan development and down-cutting in the Whataroa River where sediment input appears to be largely controlled by Alpine Fault rupture events. Medium-term assessment relied on air-photo interpretations over a period of about 50 years, with the mapping of channel changes and bank migration. Short term changes were evaluated from gauging records and other hydrological data, and took account of the development of an armour layer in these gravel-bed river systems. It was concluded that sediment in the lower reaches of each river was suitable for most aggregate uses, although input of more weathered Greenland Group materials in the upper reaches (eg of the Mawhera-iti or Little Grey) resulted in product that was not satisfactory for sealing chip or railway ballast. Of greater importance was the fact that short-term studies showed that a minimum threshold of flow was required for gravel entrainment, and that significant sediment movement only occurred above the one-year return period flood. Ongoing monitoring of river profiles, with accompanying flow gauging, would clearly be necessary were a substantial increase in river bed extraction to be permitted by The West Coast Regional Council.

Jan 1, 2003

By Lewis J. W

The mineral sand orebodies of the east coast of Australia occupy approximately three per cent of the dune-heath-wetland coastal environment. They are associated with coastal plant communities ranging from Holocene high dunes carrying mature Eucalypt forests to low- lying heaths on Pleistocene deposits. Commonly, 0.25 to 1.5 per cent of the sand volume mined is removed from the site. Therefore, the volume change is insignificant. The equipment and techniques in use are flexible and the land can be returned in a manner suited to its subsequent use for grazing, subdivision or recreation. Landforms similar to the pre-existing are created in two case studies given. Sophisticated revegetation techniques are practised and are discussed in two case studies. Pre-mining vegetation surveys and post-mining monitoring are used to guide the management of the ecosystem.

Jan 1, 1976

By Gardner CE

Uranium occurrences and the probable Australian reserves are discussed and the recovery and processing methods used in treatment plants at Radium Hill and Port Pirie, S.A., Rum Jungle and Moline, N.T., and Mary Kathleen, Qid. are reviewed. The broad aspects of the application of nuclear power in Australia are then considered, and those factors of greatest significance are highlighted. It is these factors that are most likely to dictate the future role of nuclear generation in Australia. In commenting on private industry applications, the paper emphasises that each case must be considered on its own merits, and a warning is given that general statements can be misleading. In the long-term situation nuclear power is considered to be capable of playing a leading role and the discussion covers desalination and high load industries although short term applications appear difficult to justify. In non-power applications for nuclear energy reference is made to isotopes and the uses of nuclear devices in mining and civil engineering with a pertinent comment on safety.

Jan 1, 1970

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By Anderson J. M, Gillies A. D S, Jones N

There are a number of current theories in relation to methane migration and emission into workings following underground coal mining activity and some controversies do exist. Mining causes changes in the stress regimes in surrounding strata and results in fracturing. Permeability increases and methane flows into workings under a pressure gradient. The effects of stress on permeability depend on the physical properties of the coal and surrounding strata. Methane emission also depends on the original methane content and the proportion which will be liberated. There are several methods for determining in situ methane content and desorption characteristics of coal samples and several methane prediction methods but clearly more research is necessary to achieve an adequate predictive model.

Jan 1, 1992

By Bowmaker MD

Zinc and lead sulphide flotation con centrates containing from 0.02 to 0.20% Cd are roasted on an updraught sinter machine at the Cockle Creek Works of Sulphide Corp- oration Pty. Limited to provide sinter for simultaneous smelting of zinc and lead in an Imperial Smelting Furnace (I.S.F.). The major portion (about 85%) of cad- mium in concentrate feed to the Sinter Plant is eliminated with sinter fume and is rec- overed by weak acid leaching in the Cadmium Plant'followed by counter-current decantat- ion, ion exchange concentration, precipitat- ion of cadmium sponge and partial refining to caustic refined cadmium metal. Cadmium not eliminated during sintering is volatilised in the I.S.F. and subsequently recovered as zinc alloy by distillation in the zinc ref- ining columns of the Zinc Refluxer. The partially refined cadmium metal and cadmium- zinc alloy are blended as feed to the cadm- ium refining column where separation and recovery of cadmium is effected. Condensate from the column is further refined under caustic soda flux and cast into anode shapes. Production is 200 t.p.a. at 85% recovery of cadmium in concentrates. Emphasis is placed on changes from the practice described by Baker and Munro (1965) and upon operation

Jan 1, 1972

By Gray N. B, Floyd J. M

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

This paper introduces a classification of gold orebodies, and comments on the importance of cutting high grade values, the choice of an appropriate ore reserve method and the necessity for producing recoverable ore reserves by considering the mining policy. The author stresses the importance of obtaining the appropriate information from the data relevant to a particular deposit as opposed to transfering parameters from one deposit to another.

Jan 1, 1987

By M Thomas, S Lambert

The Tugun Bypass Tunnel in Gold Coast, Australia was constructed using diaphragm walls with the top-down cut-and-cover method to allow simultaneous construction of an airport runway extension above the tunnel, whilst excavation of the tunnel continued underneath. The tunnel was built in an environment of high groundwater table and deep deposits of alluvial and estuarine soils with the toes of the walls founded in soil deposits. There was a potential risk for differential settlements to occur between the diaphragm wall panels, caused by the runway fill placed over the tunnel roof during excavation. Dewatering within the diaphragm walls was required to facilitate the construction of the tunnel. The tunnel was also built in an area where environmental considerations were of great importance. Three-dimensional numerical modelling was undertaken to predict the differential settlements of the tunnel with considerations of varying subsurface profile, staged excavation and dewatering, non- uniform surface loading and complex soil-structure interaction. Field instrumentation and monitoring was implemented to confirm numerical predictions.  

Jan 1, 2008

It's a great pleasure to be here today, for a whole series of reasons. First of all, when I first went to Perth back in 1972, I shortly afterwards began auditing and one of the people to pick on me when I audited the West Australian Newspaper at that time was Patrick O'Connor's father. One way to win a person across when you're auditing and getting picked on is by showing an interest in their children, so I did that and employed Patrick in our firm. In those days, conflicts of interest didn't occur. When I started Normandy, Patrick was one of the first people I went to get to work with me. He very unwisely chose to leave at one stage and you can see he's done extremely well by not staying with us. So it's lovely to have you here today, Patrick. The difference between Patrick and me, now, is that he's kept his hair, and if you're tall enough you can see I haven't.

Jan 1, 1997

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in piano--polarized reflected light, colour changes are observed characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film/coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins.

Jan 1, 1969

By Ogilvie M

South Bulli is the oldest and largest underground coal mine in Australia. Two longwall units are in operation and current production is 2.5 to 3 million tonnes of run of mine product per year with a workforce of 600. Prior to 1984 a workforce of around 1,200 produced 1.5 million tonnes. Advances in technology can. of course, account for some of this gain, but the changes made in the human resources area are also seen as playing a major role in South Bulli emerging as a reasonably stable operation.The human resources strategy adopted recognises the value of the workforce and is aimed at not only fostering cooperation as all levels, but also making employees aware of the direct contribution they can make to the success of the enterprise.

Jan 1, 1991

The goal of the Bureau of Mines, U. S. De- partment of the Interior, diesel engine research program is to reduce exhaust emissions and mini- mize the risk of fires and explosions caused by the use of diesel-powered equipment in under- ground mines. Significant results of research conducted during the last 5 years are briefly described, with references to published reports on specific topics. Topics covered here include brief discussions of a newly completed diesel research laboratory, the effects of a fuel addi- tive on diesel exhaust particulate matter, the effect of diesel engine maintenance on emis- sions, a diesel particulate filter for equipment used in underground metal and nonmetal, and coal mines, and lastly, the prototype hydrogen- powered mine vehicle. These research accomplishments could favor- ably affect the mining industry by reducing the health and safety hazards associated with the use of diesel-powered equipment in underground Mines.

Jan 1, 1988

By P Louden, C Rothnie, G Showers

Tiwest employs several methods to assess the quality of heavy mineral concentrates in ore and process samples. Mineralogy is determined using a method called MA98, developed in conjunction with JKMRC over the last three years (Zhang and Whiten, 2001). A range of other techniques are also used to characterise ore, heavy mineral concentrates and mineral products. MA98 is the culmination of efforts since 1989 to determine mineralogy from chemical analysis without recourse to heavy liquid fractionation, which has traditionally been used to discriminate between light-heavy , zircon, rutile and leucoxene. The major advance with MA98 is the use of statistical mass balancing for all chemical species, as opposed to reliance on key chemical species for each mineral. Three magnetic fractions are analysed by X-ray fluorescence spectrometry, with a minerals balance performed for each. Heavy mineral concentrates processed by this method include drill samples, process samples from the wet concentrators and Dry Mill, and mineral products. TBE can be avoided for higher heavy mineral grade samples since quartz is determined from SiO2 balance. In this sense the method is sufficiently universal and robust to cope with a wide range of sample types and compositions. The MA98 algorithm provides abundant information in addition to mineralogy, including TiO2 and Fe2O3 grades of ilmenite and leucoxene, and concentrations of weakly magnetic zircon and kyanite. Information such as this is invaluable in tracking different minerals through the processing plants. Other ore assessment procedures used by Tiwest provide for modelling of orebodies by mineral sizings, Fe in zircon, and FeO and U+Th in ilmenite. Microscopy is used to provide important qualitative information such as grain shape, surface staining and degree of cementing. These quality measurements are included with mineralogy in geological ore models and are available for mine scheduling. In using the above methods to characterise heavy mineral concentrates, Tiwest is better placed to predict and monitor plant performance and product quality from any ore zone.

Jan 1, 2001

By Armoo K, Tran T

Cementation has been widely used in several hydrometallurgical processes for recovering gold and silver from process liquors. The process is electrochemical in nature, in which gold and silver are precipitated from the solution using less noble metals such as zinc, iron and copper. This paper summarises the current practice of gold cementation from cyanide liquors using zinc powder. Various developmental studies on the cementation of gold and silver from various systems (chloride and bromide) are also reported.

Jan 1, 1991

By Fisher AEJ

On Sunday morning 7th November, 1976, at approximately 2-25 a.m., smoke was discovered issuing from the 1912 m long belt drift at Appin Colliery. A Clouth steel cord rubber belt approximately 940 mm in width had been installed in the drift in 1963 on the basis that no fire resistant steel cord belt was then available to operate on a single lift at the load and on the 160 gradient of the drift. Investigation showed that the belt drift was on fire and the usually downcasting drift was upcasting. Immediate fire fighting and rescue operations were instituted and the drift was sealed off. High expansion foam was pushed into the drift from the surface and the fire was brought under control. Recovery work resulted in the fire being put out and the drift open for walking traffic by, S-P0 am., on Wednesday 10th November, 1976. lie experience gained during the fire fighting and recovery operations led to recommendations in regard to future use of high expansion foam.

Jan 1, 1981