Search Documents

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

By Crapp C. E

The Collinsville Coal Measures consist mainly of arenaceous sediments but indude eleven named coal seams. The Formation outcrops around the northern end of tbe Bowen Basin where it attains a thickness of 700 ft. in the Collinsville-Scottville area and overlies Lower Bowen Volcanies with angular unconformity. Most of the members in the Formation thicken basinwards. The regional dip is about 8 degrees. The Formation thins southwards and does not occur south of the Bowen River on the eastern flank. On the western flank it is represented by 60 ft. of barren sandstone at the limit of our mapping, 12 miles south of the Bowen River. Two seams are mined, the Bowen and the Blake; coal from the former produces high grade metallurgical coke, and the latter seam is mined for steaming coal. Where mined, the seams are about 20 ft. thick. The coals are of medium volatile bituminous rank and the lower coals are of higher rank than those above them.Reverse faults striking across the Coal Measures have been delineated and the existence of areas of intrusive rocks has been established. Intrusions rose up fault planes and, as felspar porphyry sills, selectively intruded coal seams, decimating reserves of coalavailable for mining. One sill, in the Blake Seam, attains a known thickness of 115 ft. Because the distribution and thickness of the sills is rarely predictable, density of drilling has been greater than in most coalfields.INTRODUCTIONThe assemblage of sediments occupying the northern portion of the Bowen Basin (Fig. 1) may be divided into four formations of Permian age:The Upper Coal Measures (U. Bowen)The Middle Bowen Marine Beds (M. Bowen)The Collinsville Coal Measures (M. Bowen)The Lower Bowen Volcanics (L. Bowen).Of these, the Upper Coal Measures and the Collinsville Coal Measures are known to contain coal seams of workable thickness.

Jan 1, 1960

By Robinson WB

An accurate and rapid assessment of coal resources, such as that provided by computer modelling, forms an intergral role in evaluating CSR's coal deposits for future development. An in-house system utilising a number of geological, engineering, costing and financial evaluation routines has been developed for DEC VAX computers. The system is currently being upgraded and enhanced to meet the demands at the various mine sites. Computer modelling of the geology is performed on encoded drillhole information and coal core chemical and physical analyses. A conceptual mine plan is formulated then digitized and superimposed on the geological model. Insitu and product coal reserves and qualities as well as overburden and parting quantities are then calculated for each strip or block. These strip parameters are then transferred to the mine scheduling routines to determine the most efficient mining sequence for the mine plan. Cost factors and scheduling data for equipment specified in the conceptual mine plan are used in the mine costing subsystem. The financial subsystem then evaluates the likely return on investment. Future enhancements to the system include improvements in the response time through the introduction of interactive graphics, the direct interfacing of geophysical and analytical data, and further development of a geotechnical'database.

Jan 1, 1983

By S Paciornik, G Schinazi, M H. de Pinho Maur-cio, M B. Vieira, O da Fonseca Martins Gomes, D T. Wagner

Vale (previously CVRD û Companhia Vale do Rio Doce) evaluates the microstructure of sinters in order to understand their characteristics and behaviour in the agglomeration process, and the correlation with conventional quality parameters. Efforts on image analysis development are in progress between Vale and PUC-Rio in order to improve both the qualitative and quantitative evaluation of a representative portion of material. In the present work, digital microscopy techniques were developed allowing this kind of assessment. Employing a motorised and computer controlled optical microscope, low magnification mosaic images covering complete sinter samples were automatically obtained. The mosaics provide a powerful qualitative overview of the whole sample while allowing low resolution quantitative evaluation of the major phases. In addition, quantitative results for phase fractions were compared for the same sample regions at three magnifications (5x, 10x and 20x objective lenses). A single field (1 x 1) at the lowest magnification corresponds to mosaics of 2 x 2 and 4 x 4 images at the higher magnifications. The automated system allows perfect registration between the mosaics and the single image. Changes in phase discrimination were evaluated as a function of optical resolution, and phase fractions obtained by interactive segmentation of the image histograms were compared. While finer dark phases, eg silicates, were only visible with the best optical resolution, coarser phases such as haematite and pores were measured at all resolutions. For haematite, magnetite, ferrite and pores, the largest relative error in area fraction, between the images obtained with the 5x and 20x lenses, was 12 per cent. The results for silicate were less accurate with a relative error of 44 per cent. The results indicate that digital microscopy provides a flexible method for qualitative and quantitative evaluation of these materials.

Jan 1, 2008

By Mozley R

Contaminated sediments are a multinational problem. A crucial factor in solving an environmental problem is knowledge of, not only the amounts of polluted soil, the contaminants involved and their concentration, but also the historical background of the problem. Processing polluted soil is a tailor made activity based on rational decisions resulting from a detailed treatability study. Lack of information about characteristic properties of a specific sludge/pollution combination is the main obstacle in the route from first ascertaining that a particular harbour subsoil is polluted, to final identification of the full scale treatment plant. In the first instance, information must be generated regarding the distribution of pollutants in relation to the distribution of the original geophysical components. Based on this information rational decisions can be made on separation at a particular cutpoint and what sequential techniques should be involved for a certain fraction. For this purpose a `fingerprint method' is presented especially developed for investigation of polluted soil and sediments. The heart of the fingerprint method is a series of sequential hydrocyclone separations, by which a series of products is generated. The objective of the fingerprint method is to select an optimised treatment procedure in which the pollutants are concentrated in as small a volume of material as possible, leaving the bulk of the material clean. The pollutants can then readily be destroyed or isolated from the environment. The philosophy and advantages of the fingerprint method are demonstrated for a harbour sludge containing heavy metals as main pollutants. Hydrocyclone separation combined with flotation of both the coarse and fine fraction resulted in reusable and dischargeable products. Flotation of the fraction of fines was carried out by means of an experimental flotation cyclone enabling the selective recovery of mineral particles with diameters less than 10 microns. The overall conclusion is that design and engineering of treatment flow schemes for polluted dredged materials is a tailor made activity based on rational decisions resulting from the fingerprint information.

Jan 1, 1993

By D Nourry

Optimising the blast is a major issue in the blasting business. It generally means acting on the blasting pattern (drilling, charging, detonating) in order to get a given æresultÆ. This result may either be related to economic reasons, such as the fragmentation influencing productivity, or technical reasons, for example vibrations and projections. Within the frame of the EEC funded Brite-Euram project entitled æBlast-ControlÆ, involving academic research and applied expertise, a general methodology was developed to approach such a problem and currently applied to the industrial partners of the project and final end-users of the generated results. These partners are the limestone ALZO quarry of the CALCINOR group in the north of Spain and the dolomite DMD (Dolomies-de-Marche-les-Dames) quarry of the LHOIST group in the east of Belgium. A first part of the project, over 18 months, was dedicated to establishing a clear relationship between productivity of operations from drilling to primary crushing and the fragmentation resulting from the blast. Extensive monitoring of blasting, production performance and fragmentation data was carried out and automatically collected into a database on both quarries. As expected, it appeared that excessive amounts of fines or boulders were substantially reducing productivity and thus profitability of the operation. Furthermore, an æoptimalÆ fragmentation was assessed for the quarries to run at the best (high throughput, low cost). The second and last part, for the remaining 18 months, was then dedicated to adapting the blasting practice in order to orientate the fragmentation towards a æbetterÆ one. A very common problem normally addressed by any consultant. Nevertheless, the target was not limited to solving the problem for these two quarries, but also to develop a generic method to address this blasting adaptation process and to implement it into a computerised tool. At this stage, it is then obvious that portability of the method and the system are major qualities to be looked for. This paper is aimed to present how this method was developed, how the system was implemented and how it was finally used.

Jan 1, 2001

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

Published information on technical and market developments in the uses of zinc tends to dwell very largely on two groups of uses of zinc - zinc coatings (mainly galvanising) and zinc casting alloys. These two groups account for two-thirds of primary zinc consumption. However, if total zinc consumption is taken into consideration, coatings and casting account for a little over half the total. Either way, the health - or otherwise - of these 'other' uses of zinc can have a substantial effect on the industry as a whole. The aim of this paper is to put the whole market picture for zinc into better focus, concentrating on the factors which can affect consumption in the 'other half' of zinc's markets: ò brass - the third most important market for zinc at around one million tonnes - responds to changes in the economic cycle. It has seen substantial changes in the balance between different forms of semi products, and, in Europe at least, some real market gains; ò zinc sheet - one of the original uses of zinc in Europe - has grown substantially in some countries, but remains almost unknown elsewhere; and ò zinc pigments and compounds are so numerous that - barring the substitution of zinc oxide in rubber - major overall changes in the market are unlikely. The paper examines these markets and assesses their potential and implications for zinc markets as a whole.

Jan 1, 1993

The scope of this paper has been restricted to the manufacture in Australia of seamless steel tubing, as the subject of buttweld tubing has already been dealt with by A. N. Hamilton in a paper delivered before the Institute in 1935.The earliest attempts to produce seamless steel tubes were based on the extrusion of lead piping, a process developed by Thomas Burr in 1820. However, the problems associated with the extrusion of white hot steel had to await the metallurgical knowledge of the twentieth century, and these early attempts were unsuccessful.The years 1840 and 1845 were noteworthy for the introduction of the first practical methods of making seamless steel tubes. In one process, a large circular plate was 'cupped' in a vertical press; in the other, a round steel billet was pierced for its entire length.The product from both these methods was then elongated by repeated reheating and rolling over an internal mandrel, in a circular pass mill.At this juncture, it should be noted that every process developed for the manufacture of seamless steel tubing can be divided into two parts. In the first part of the process, attention is centred on the conversion of the heated bloom into a short, thick-walled, hollow cylindrical forging; this product is then elongated in the second section of the process. It will be noted that these two sections are actually quite distinct, and in practice numerous methods exist for carrying out both functions. The first stage is generally referred to as 'piercing', the second stage being termed 'elongating.' In this paper, the author proposes to outline the various methods adopted for piercing and elongating; the reader is asked to note that although certain methods of piercing are almost invariably associated with only one method of elongating, the distinction between the two functions is, nevertheless, a vital one and should be noted accordingly.

Jan 1, 1947

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

By S Rice, A Midlin

Many of the stacking and reclaiming machines employed in the mining industry today are operating in ways that were never envisaged in the days before they were commissioned, with greater throughput, increased annualised operating hours and load cycles well in excess of their original specification requirements being the norm. In many cases these machines were supplied prior to the widespread use of finite element modelling or, in the era when such software became commercially available, those supplied designed using simplified and/or coarser meshes than would be employed today. With many of these machines being expected to operate for many years to come, it is important that their ongoing reliability be maintained and their operational limits understood. In this paper, a case study is used to outline the method required for estimating the fatigue life already consumed and the likely real life left in a machine. By reference to the machineÆs prior operating history, the use of strain gauges in the field and the development of finely meshed finite element analysis (FEA), a coherent picture of the machineÆs operational state can be generated and then investment/maintenance decisions made to ensure continuity of machine operation.

Jan 1, 2007

By Adams DG

At Cook Colliery a combination of main injection of the face coal, and mining into the floor has proved successful for the recovery of faceline falls.The strategy for preventing falls relies upon a conventional method of longwalling. improved geotechnical predictions, and continuous assessment of strata conditions. Different categories of faceline stability are recognised and an operating procedure has been developed for each category.

Jan 1, 1991

By Childs G, Ritchie IC

This paper describes the principle and operation of small hydrocyclones for use in the coal, minerals and other process industries. The principles for selecting a hydrocyclone for an application are also discussed. Typic- al uses and installations in various industries are described.

Jan 1, 1984

By P Pelletier, J Tessier, C Duchesne

This paper summarises research into the study of the control of flotation processes based on froth images. A review of the froth flotation operation background and the relevance and role of the froth phase are presented. The use of numerical image analysis techniques for the extraction of significant patterns from industrial flotation froths is discussed. First, the froth was analysed by the use of the multivariate image analysis (MIA) method to extract the spectral variation contained in a RBG image. The partial least squares (PLS) method was applied to develop an empirical model for the prediction of froth grade. The results of this application are illustrated using an industrial case study. Second, the froth was also analysed by grey-level co-occurrence matrix (GLCM) and wavelet transform analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths. They also provide qualitative information on the changes in the visual appearance of the froth. The pros and the cons of those methods are highlighted. Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses the reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained from the implemented control strategy are highlighted. Finally, the feasibility of implementing a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.

Jan 1, 2005

By M Wortley, A Cantarutti, T Ozkocak

The estimation of the grinding mill charge weight is vital to ensure its efficient performance. Mill underloading or overloading can cause losses through decreased production or unplanned down time. Metso Minerals Process Technology Asia Pacific and South America (MMPT) has developed two systems for measuring mill load. The first is an acoustic system (SmartEarÖ) and the second is an online model-based charge estimation system. The aim of both systems is to facilitate better operation of grinding mills. SmartEarÖ performs analysis on an audio signal from the mill and allows each different frequency component to be viewed, analysed and used in process control for load estimation. By isolating different frequencies, SmartEarÖ can give an estimate of mill load. The online dynamic mill model uses measurable mill parameters (such as power) to predict the current total load. Kalman filtering can also be utilised to further increase the accuracy of the model. Both of MetsoÆs systems have been installed at BHP BillitonÆs Cannington mine to measure the load within their autogenous (AG) mill. In this paper, the methods of mill load estimation are reviewed and compared to the bearing pressure reading, which is the current method used by Cannington to control mill load. The redundant estimates of mill load provide increased confidence and consequently more robust grinding operation under a wide range of conditions.

Jan 1, 2008

By Jackson E

The general level of awareness amongst members of the professions that they are faced with an increasing number of claims for breaches of their professional duty was dramatically heightened by the decision of Rogers J. at first instance in Cambridge Credit Corporation v Hutcheson (1985) 3 ACLR when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million - well in excess of their insurance cover. No comfort should be found in the fact that this decision was overturned on appeal, for that result rested on the issue of whether there had been a causal connection between the breach of contract which had occurred and the loss suffered rather than on the fundamental principle of auditors' liability.

Jan 1, 1989

By P T. Hick, T J. Cudahy, M S. Caccetta

Dust derived from mining and handling of ore has been identified as a major concern for the mining industry in Australia and may be critical to the future viability of some resource industries (CSIRO, 1999). Operational techniques to derive accurate measurements of anthropogenic dust on vegetation and infrastructure are necessary for the long-term management and monitoring of the environment surrounding mining operations. Airborne hyperspectral VNIR-SWIR systems can potentially provide these monitoring data. This paper outlines a method developed for deriving quantitative measurements of dust quantity on mangroves using remotely-sensed airborne hyperspectral data. The results show that it is possible to detect and quantitatively map iron oxide dust distribution using properly calibrated airborne visible to short wave infrared (VNIR-SWIR) data.

Jan 1, 2002

Mining operations have been carried out at Mt. Lyell for the past century. Until the 1970's the location of the mines in relation to the surface topography has enabled the mines to drain their copious inflows of water by gravity. Deeper mining has forced the Company to undertake pumping of increasing inflows of water. A major pumping facility is being established near the base of the known ore reserves with a view to serving the future requirements of the mines. The system has a design capacity of 600 litres per second. Run of mine water will be treated in Vertical Flow Settlers to produce clear water and thickened mud, each of which will be disposed of separately. The clear water will be pumped by six 1000 kW conven- tional centrifugal pumps. The thickened mud will be removed by a Hydraulic Displacement System. The rising mains for both the mud and the clear water are stainless steel cased bore- holes.

Jan 1, 1982

The flotation circuit handling Peko ore at Peko Mines N.L. was examined in July 1970 with a view to determining simple changes in circuitry or reagents which could improve the grade and recovery of the final copper concentrates. The investigation included sampling over one shift followed by detailed testing of the samples by sizing-assays, sizing-mineralogy and sizing-liberation. Mass balances were carried out over total streams, the component minerals and the copper contents. Some laboratory work was carried out to assess the effect of salinity on flotation. In order to handle the sizing-mineralogy calculations a computer programme was set up. The raw data were corrected for locking factors, then mineral and elemental distributions cal- culated for each screen fraction and the total sample. Calculated assays from grain counting were compared with chemical assays. Recoveries through the size-ranges re- vealed very rapid flotation of copper minerals at sizes below 350 mesh. This pointed to a possible circuit improvement by desliming rougher tailings ahead of the scavenger stage. A strong correlation was found between water in concentrates and gangue recovery for the subsieve sizes. This pointed to clean water additions to the cleaner circuit as a way to 1 Project Consultant, The Australian Mineral Development Laboratories, Adelaide, South Australia.

Jan 1, 1972

A laminar-flow furnace was used to study the combustion of four flotation concentrates (chalcopyrite, pyrite, galena, and sphalerite) in air at temperatures up to 1400¦C. A special- Iv developed two-colour pyrometer was used to measure the temperature of individual chalco- pvrite and pyrite particles as they underwent combustion. Chalcopyrite and pyrite ignited with very high rates of reaction at air tempera- tures above 480 and 600¦C respectively, forming molten products. Galena and sphalerite required temperatures in excess of 700 and 1200¦ respect- ively to attain equivalent rates of reaction. The high rates of reaction for galena and spha- lerite were caused by vaporization. Temperature measurements for chalcopyrite and pyrite are reported here, together with vaporization measurements for chalcopyrite, galena, and Sphalerito

Jan 1, 1980