Search Documents

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

By A Taheri, G D. Nguyen, M Karakus, S Akdag

During underground mining operations, rock masses are highly subjected to dynamic disturbance caused by blasting, mechanical drilling and earthquakes resulting in strain burst, slabbing and spalling. The dynamic fracture is a significant manifestation of rock failure in deep underground engineering, and it is of great importance to assess the dynamic fracture behaviour of the rock mass under elevated temperature conditions. The correlation between temperature – and loading rate-dependent dynamic fracture mechanism of strain burst is yet to be established. A good understanding of the dynamic fracture behaviour of brittle rock subjected to high-temperature under dynamic loading is required for the prediction of the damage extent during strain burst, and proper design as well as control of the underground rock structures. In this study, dynamic mode I fracture toughness tests are carried out on cracked chevron notched semicircular (CCNSCB) granite specimens to reveal the dynamic fracture characteristics of the brittle rock. For this purpose, a Split Hopkinson Pressure Bar (SHPB) apparatus is utilised to conduct the dynamic tests with various striker velocities on thermally degraded granite. The dynamic mechanical behaviour of granite after high-temperature treatment is examined and discussed. The dynamic fracture toughness is determined and compared for the specimens exposed to different temperatures at various dynamic impacts. The fracturing processes are recorded by a high-speed camera (HSC), and the crack propagation speeds are estimated by HSC image analysis. In addition, the dynamic fracture process and the coupled effects of temperature and loading rate on the dynamic fracture modes are identified by HSC image analysis. Energy partition characteristics in dynamic fracture of granite are quantitatively investigated.

Nov 29, 2022

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

Determining the controls of high-grade mineralisation at Vera Nancy requires careful data collection and assessment on a global and specific deposit basis. The techniques developed over 60 years ago to analyse structure, grade and width data are just as applicable today and can be enhanced using modern geological modelling software. High ore grades at Vera Nancy are controlled by both the primary geometry of the mineralised structure and the intersections of the main mineralised veins with subordinate splay veins. The main mineralised structure dilated as a consequence of extensional tectonics while the splays acted as conduits bringing oxidising surficial fluids into mixing zones precipitating high gold grades. Near-mine exploration is focussed on identifying zones of vein flexure and splay interaction to locate the relatively small high-grade shoots. Data modelling in a 3D environment is an essential process for understanding the geometry of the system being explored.

Jan 1, 2000

By R C, K L. Rees, J S. J van Deventer

In contrast with previously published models for the carbon-in-pulp (CIP) process, the model proposed in this paper incorporates film transfer, intraparticle diffusion, simultaneous leaching, preg-robbing, the loading of multicomponent species, and the effects of fouling and changing cyanide levels. The rationale behind this comprehensive model is that changes in fouling and competitive adsorption along a CIP cascade affect the profiles of gold loading. As it is impossible to quantify all these non-ideal factors, a method is proposed whereby an imaginary species is postulated so as to combine all the competitive effects. A plant survey at the Telfer mine has shown that the mass loss due to a gravimetric analysis of the fouled carbon could be used directly to quantify this competitive effect. The degradation and consumption of cyanide along the Telfer CIP cascade enhance the loading of copper on to the carbon, which should be taken into account when modelling the gold profiles. It appeared that the effect of cyanide itself on the loading of gold was negligible compared with its effect on the copper. Evidently much more research is required on this topic in order to optimise CIP operations exposed to constantly changing conditions.

Jan 1, 1998

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

By M T Roche

The Cannington deposit is one of the largest accumulations of silver-lead known. Located 135 km southeast of Cloncurry in North West Queensland (Figure 1), Australia, the deposit is currently in the feasibility stage of its development. The deposit is named after the nearby Cannington Pastoral Property which runs some 25 000 sheep on 'downs' country. The investigations of the Cannington deposit are carried out under the authority of Mineral Development Licences 139 and 144 and Exploration Permit for Minerals 6788, Answer Downs. Exploration for Broken Hill Type (BHT) silver-lead-zinc deposits in the Mt Isa region has been undertaken by The Broken Hill Proprietary Company Limited's Minerals Division (BHPM) since the early 1980s following in-house research which showed that the Eastern Succession of the Mt Isa Block exhibits characteristics which were favourable for hosting BHT

Jan 1, 1994

By H Zhang, S Li, J Song, Z Lv

In this paper, a method for extracting and refining metallic molybdenum using low-temperature ZnCl2- NaCl-KCl molten salt was proposed. The electrochemical behaviour of molybdenum ions in ZnCl2- NaCl-KCl molten salt was investigated in detail, and pure metallic molybdenum was collected on the cathode. The reduction and diffusion processes of Mo(V) ions in ZnCl2-NaCl-KCl molten salt were determined through a series of electrochemical methods. The diffusion coefficients and nucleation modes of Mo(V) ions were also studied, and electrolysis was conducted for a prolonged period at a constant current density. The results indicated that the electrode reduction of Mo(V) ions in ZnCl2- NaCl-KCl molten salt proceeds through a three-step reaction: Mo(V) → Mo(IV) → Mo(III) → Mo at 250°C. The Mo(V) → Mo(IV) reaction was reversible and diffusion-controlled, with a Mo(V) diffusion coefficient of 6.02 × 10-6 cm2 s-1. Additionally, the nucleation mode of Mo(V) ions was instantaneous nucleation. The products electro-deposited were confirmed of metallic molybdenum with a particle size of less than 1 μm.

Aug 21, 2024

By J J. Wilkinson, C J. Ha, R J. Herrington

The Pic de Fon iron oxide deposit is a potential major new source of iron ore, located at the southern end of the Simandou range in eastern Guinea on the West African Craton. The deposit is hosted by banded iron formations (BIFs) within a supracrustal sequence, which lies unconformably upon a crystalline basement. The host BIFs and shales have been metamorphosed up to staurolite-grade itabirite and phyllite respectively. Stratigraphic relationships are obscured by polyphase deformation, although the sequence appears to comprise a lower phyllite(-minor quartzite) unit and transitional phyllite-iron formation overlain by three itabirite units. It is the itabirite units, selectively enriched to iron grades in excess of 65 per cent Fe (with low deleterious elements), that constitute the Pic de Fon deposit. Samples acquired from exploration diamond drill holes and outcrop across the deposit have been collected to investigate the Pic de Fon lithologies and iron-rich material types. Initial research techniques have included geological mapping, reflected light microscopy, x-ray diffraction (XRD) studies and ICP-AES geochemistry. The aim is to develop a model for deposit genesis that may assist future exploration and deposit exploitation planning. Results to date have identified a variety of hematite textures, which include recrystallised trellis, interlobate and granoblastic hematite after magnetite. In addition, fine-grained bladed to acicular microplaty hematite appears to both replace itabirite banding and infill porosity. Field relationships indicate a structural control of microplaty hematite development. Geochemistry and XRD results suggest a loss of silica with negligible iron addition during the conversion of itabirite to ore grade mineralisation. The enrichment process(es) is also accompanied by a gradual increase in K, Mg, Na, (Ca and Al).

Jan 1, 2005

During the 20th century, the iron ore mining industries of Canada and the United States passed through several periods of transformation. The beginning of the 21st century has seen yet another period of transformation, with the economic failure of a number of steel companies, the acquisition of their facilities by more viable steelmakers, and the consolidation of control within the North American iron ore industry. Changes in Canadian and United States iron ore production and the market control structure involved are analysed. The consolidation of ownership, formation of foreign joint ventures within North America, planned divestitures of upstream activities by steelmakers, and industry changes made to ensure availability of feedstocks will be reviewed. The traditional isolation of the Canadian and United States iron ore operations and their strong linkage to downstream steel production will be discussed in the context of a changing global economy. Management-labour conflicts that have taken place and agreements made during 2000 through 2004 will be discussed in the context of the economic environment leading up to these agreements. Cooperative agreements between competing Canadian and United States companies to resolve client needs in processing and blending will be examined. A joint industry-government project designed to use new technology to produce direct reduced iron nuggets of 96 - 98 per cent iron content using non-coking coals will also be assessed. Changes in iron ore transportation methods, ownership and infrastructure will be reviewed for both rail and inland waterway transport between Canadian and United States companies. A brief analysis of social and environmental issues relating to sustainable development of the Canadian-United States iron ore industry will be included.

Jan 1, 2005

By Hilde TWC

Synthesis of GLORIA side-scan sonar and other geophysical data has provided morpholo- gical and tectonic details of the interaction between the Nazca and South American plates along the Peru Trench (80S-15¦S). Our analyses suggest that a new propagating rift of the Galapagos type is evolving along the Mendana Fracture Zone (MFZ). Subduction induced rift- ing of the Nazca plate is accompanied by organized seafloor spreading for the last 3 Ma at least. GLORIA sonographs and bathymetric mapping show an 8-10¦ divergence in MFZ width towards the Peru Trench. The fracture zone comprises numerous ridges and troughs and a lack of sediment cover in the axial part. Young magnetic lineations (anomalies 1-2A) are observed within the fracture zone wni.cn are orthogonal to the older Nazca plate lineations. The central anomaly narrows west- ward and can be observed up to 400 km seaward of the trench whereas anomaly 2A is terminated about 200 km from the trench axis. Recent SeaMARC II sonar mapping in the region shows large igneous blocks in the Trench axis to the north of MFZ but absent to the south. We believe these blocks represent young seafloor of MFZ rift/spreading center broken off from the ridges as they subduct along the Peru Trench. The MFZ rift is propagating west- ward at a rate of 115 km/Ma (25 km/Ma relative to the South American plate). Given the present rates of accretion at the East Pacific Rise and of propagation along MFZ rift, the Nazca plate will be divided into two parts in about 35 Ma.

Jan 1, 1987

By Lee M. F, Guilfoyle K

A large hard rock rib pillar was recently preconditioned at Mt Charlotte mine using a novel blasting technique. The motivation for trialling this procedure was a history of past pillar failures, with associated seismicity. Design studies had shown that a new proposed pillar would be at risk of violent failure, and preconditioning was used in an attempt to reduce this risk. Preconditioning by blasting involves physically modifying a selected zone of ground in advance of mining, then forming the pillar so that it incorporates that zone of ground. The modified rock in the zone is intended to allow extra closure (yield) of the pillar in response to mining-induced stress changes. The ground modification was done by tight firing a blasthole array to fracture the rock. The blast design comprised pairs of pre-split blastholes to create a series of short cracks across the target zone, followed by main blastholes to fracture the rockmass between each pair of cracks. A monitoring program was used to establish whether or not the preconditioning was effective. It included conventional extensometers, stress change cells and closure stations, plus a seismic monitoring system. To-date, stoping is complete on one side of the pillar and has just commenced on the other. Results show significant movements within the preconditioned zone and on geological structures in the pillar, as well as lower stress in the pillar compared to an adjacent non-preconditioned site. The preconditioning technique can be applied elsewhere, provided its purpose, mechanism and side effects are understood. Benefits are likely to include more assured production, and successful pillar recovery even in high stress situations.

Jan 1, 1995

By C P. de Jager, J J. Taljaard

Over the past 75 years, the mining of platinum has predominantly focused on the Merensky Reef horizon in the western Bushveld region of the Bushveld Igneous Complex (BIC) of South Africa (Figure 1). The orebody is relatively flat dipping at 10¦ to 25¦, narrow tabular in shape and has been mined to a maximum depth of some 1600 m within Anglo Platinum. This has resulted in the installation of up to four generations of shaft systems as mining progressed into reserves at greater depth. In recent years, with the improvement in processing technology and improved economics, in particular with the improved price of palladium, the mining of the UG2 Chromitite Reef is proving economically viable. The UG2 Chromitite Reef occurs below the Merensky Reef in the succession and the normal separation varies from 15 m to 400 m, with the largest separation between the reefs occurring in the eastern region of the BIC. The UG2 Chromitite Reef horizon is now being accessed from existing Merensky mining infrastructure by cross-cutting back through the stratigraphy where appropriate, or by establishing new decline cluster systems from surface, along the extensive strike length of the various mining properties. These declines are generally established utilising mechanised mining techniques. This paper gives an overview of the techno-economic approaches considered and evaluated for the selection of the optimum mining and shaft systems. More specifically, the paper reviews the design parameters used, techno-economics, conveyor versus haul alternatives, logistics simulations, capital costs, system performance, time to market or ramp-up success, important system differences and lessons learnt.

Jan 1, 2005

By I Y. Maslov, S A. Gorinov

It was demonstrated that the stable propagation of the explosive process is possible in low-density emulsion explosives (EEs) obtained through mixing of emulsion with a significant amount of expanded polystyrene (or other similar) granules. Such a process takes place in the form of a detonation-like wave of emulsion drops in explosive gas streams flowing out of the high-pressure area of the reaction zone.Chemical reaction in such EEs takes place in the form of surface combustion of emulsion particles interacting with the gas stream.A method was developed for determining parameters of decomposition of low-density EEs, and it was demonstrated that a gradual pressure increase takes place in products during the explosion of such EEs.The performed analytical research allowed low-density EEs (obtained through mixing of emulsion with a significant amount of expanded polystyrene) to be recommended for smooth blasting.Industrial-experimental blasts at quarries of Ural and Siberia, with extreme positioning of sides and using low-density EEs, have confirmed the viability of the recommendations given.The obtained results are useful in the advancement of smooth blasting technology using low-density EEs.CITATION:Gorinov, S A and Maslov, I Y, 2015. Physical and technical evaluation of possibility using low-density explosives in smooth blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 555–564 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D B, M A. Sares, D W. Coulter, D C. Peters

This presentation discusses NASA-funded research on the ability of hyperspectral remote sensing to map diagnostic acid rock drainage (ARD) mineralogy that adversely affects water quality within watershed and to determine the relative contributions of natural ARD sources of metals and acidity to that drainage. Ground-based reflectance spectroscopy, combined with water chemistry, is used to identify mineralogical and chemical variations throughout a watershed. Integrated with hyperspectral data acquired from airborne remote sensing platforms, such as the NASA Airborne Visible Infrared Imaging Spectrometer (AVIRIS) sensor, a methodology has been developed that should improve environmental assessments and tracking of impacts on and from drainages. Phase I of this project focuses on a drainage basin (Lake Creek), tributary to the upper Arkansas River in central Colorado, which is impacted by natural acid rock drainage from areas of high-sulfide hydrothermal alteration. This project builds upon research and inventory efforts by the Colorado Geological Survey (CGS) to identify hydrothermal alteration that is the primary source or is contributing to acidic and toxic drainage in Colorado. This presentation will cover ground and airborne hyperspectral remote sensing techniques and results and water analyses for seasonal high-flow and low-flow conditions in Lake Creek. Identifying correlations between mineralogy, especially mineralogy that can be identified through airborne remote sensing, and water chemistry is a key focus of this project. Of particular interest are low-pH iron phases such as jarosite, ferrihydrite, schwertmannite, copiapite, and transitional amorphous phases as well as AlOH phases from higher, although still acidic, pH environments which are observed to mix with the iron precipitates within the streams draining from the hydrothermal systems. Drainage in the Lake Creek watershed derives from the Grizzly Peak caldera (Oligocene), which exhibits extensive hydrothermal alteration. Alteration types include silicic, quartz-sericite, quartz-sericite-pyrite, advanced argillic, and argillic. By understanding the chemistry of a naturally impacted drainage and its relationship to the surrounding geology, the project goal is to allow more efficient and complete identification of such sources in mineralised terranes through remote sensing technology.

Jan 1, 2003

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By Lawrence M. J

It must be stressed that the following comments are offered only to assist mineral industry professionals in understanding the issues involved in personal liability. The information and views expressed herein are not intended to be a comprehensive guide or definitive statement of the law and they should not be regarded as a substitute for specific advice for individual situations. Readers should consult their own legal and other professional advisers before applying the content of this paper to their own particular circumstances. It is hardly news that work in the mining industry is governed by a complex regulatory and legal system which is constantly changing, but few realise just how directly they can be affected and become personally liable for any breaches. These may result in civil or criminal proceedings and personal assets are at risk. Owners, company directors, managers and now employees are at risk, together with consultants, contractors and suppliers of equipment or consumables, as well as government inspectors. They are liable for their personal decisions to act (or failure to act) in managing operations or carrying out directions, as well as for the actions of others under their control. This paper identifies the areas where such individuals in the open pit mining industry in Australia face the risk of personal liability and measures which can be used to minimise the risk or which can be used to make out a defence to legal action which could arise. There have always been a myriad of Commonwealth, State and Local Government laws and regulations with which to comply, and now international protocols are being used as a basis to impose greater obligations on all people. Once, the `corporate veil' gave some protection to the individual, but today there is negligible protection from the full force of the law. Not only are there various types of law enforcement officers, but public interest groups, shareholders, customers, suppliers, creditors etc may litigate. This paper is not intended to be an exhaustive discussion of the provisions of all the legislation or case law where individuals can be held) personally liable. These areas would include environmental, pollution and heritage law (including Aboriginal sacred sites); occupational health and safety (including workers' compensation) law; trade practices and fair trading law; contract law; corporations law (including the requirements of the Australian Stock Exchange [ASX] and Australian Securities Commission [ASC]); industrial relations law; anti-discrimination and sexual harassment law; taxation (including superannuation trustee) law; and the Common Law. The focus is on the following areas of regulation, which are outside the usual experience of those in the open pit mining industry (the Mining Acts and Regulations are specifically not dealt with here): ò Environment Law; ò Trade Practices Law; ò Occupational Health and Safety Law; and ò Corporations Law.

Jan 1, 1994

By D Whitworth

The Golden Pig mine has embarked on a diamond drill program design philosophy that increases flexibility of the program by greatly increased drill pattern densities. The use of standard broad pattern diamond drilling at the Golden Pig mine has previously lead to operational inefficiencies and impacted significantly on the costs of the mine. The diamond drill program philosophy and its interaction with mine planning is explained. The case study of the E lode mining as used to internally justify the increased drill densities is detailed.

Jan 1, 2002

By G Varley

This paper describes the mining methods and strategy used to extract the 5 Orebody crown pillar at the Isa Lead Mine over the past five years. The bulk of the crown pillar was extracted by the use of sublevel open stope method. An uphole bench stope was mined to scavenge the remaining ore. Geomechanical issues associated with the crown pillar extraction are described. Stope sizes were gradually increased on a stope by stope basis. This has allowed the maximising of ore recovery while relevant risks were managed. The principles in designing ore rib pillars against various types of fill materials are also described.

Jan 1, 2002

By R L. Koenig

Previous papers at Metplant conferences have covered the options for crushing and grinding circuit selection. High Pressure Grinding Rolls (HPGR) may have considerable advantages over autogenous milling circuits but test work and evaluating different grinding circuits must be done to establish which circuit provides the best option. The Hawsons low grade magnetite project provides a specific example in using thorough test work, careful simulations and detail in design to allow the evaluation of grinding circuit performance. Fortunately tools are available for this evaluation and the test work for the Hawsons iron ore is detailed in this paper. The results of the test work and simulation indicates that although the Hawsons iron ore is competent in terms of autogenous milling given the medium hardness of the ore in the Drop Tests, the HPGR testing indicates that the use of HPGR is likely to use half the energy requirement. This is a characteristic of the Hawsons iron ore and is likely to be valid for other iron ores in the Braemer Iron Formation which stretches from the Hawsons lease in New South Wales to Razor Back and South Dam in South Australia. The Hawsons magnetite iron ore resource has been known from the early 1960s when CRA explored the area. However, the Pilbara region was discovered in this era and this led to development of high grade direct shipping grade hematite ores. Carpentaria Exploration (Capex) rediscovered the magnetite whilst undertaking multi-commodity exploration in the Broken Hill district during 2009. The magnetite grade was found to be low at around 16% Davis Tube mass recovery (DTR) but despite this, the project provides a positive business case as a result of the following key factors:• The mineralisation is particularly soft for crushing and grinding with a Bond Work Index of 6.3.• The mineralised rock fractures easily preferentially along grain boundaries.• The location is close to mining infrastructure and a skilled workforce in Broken Hill, 60km to the North East.• It is close to road and rail infrastructure for access to the resource.• The only contaminant in concentrate is silica.• The resource contains many billions of tonnes of magnetite mineralisation.The low Bond Work index is a key characteristic of the Hawsons iron ore and the use of autogenous milling and HPGR circuits is compared to other iron ores indicating why the plant energy requirement may be just as important as iron ore grades.

Aug 8, 2011