Search Documents

By K Kuganathan, Y Potvin

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: a minimum filling rate of 250 m3/h, a curing time of 28 days, and minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

The mIning operations of Bougainville Copper Pty. Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea.C.R.A. Exploration Pty. Limited first established mineralization in the Panguna area in 1964. Exploration work since then has established ore reserves estimated to be 900,000,000 long tons of ore assaying 0·48 per cent copper and 0·36 dwt/ton gold. An economic feasibility study completed in July, 1969 enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons/day. The concentrate will be pnmped as a slurry through a 16 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 MW steam power station, and access roads.

Jan 1, 1971

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

Whether you are an employee, contractor or consultant working in the mineral industry, there are pressures to deliver the best possible performance. Technical professionals are usually driven by an internal desire to perform to a high standard because of personal pride in their profession, but there are an increasing number of external requirements to demonstrate that the actions taken were based upon reasonable grounds and that the work conformed to current best practice. People expect these best practice procedures to be followed and governments are now requiring those tendering for contracts to be registered in some way and to be participants in quality assurance schemes. One is not immune to these pressures just because you are working in a less legislatively sophisticated developing country in the circum-Pacific rim (Pacrim) region.

Jan 1, 1995

By K-S Kim, C-Y Kim, D-G Kim

In tunnel construction or other underground construction, a detailed knowledge of the rock mass ahead of the face is essential for both safety and efficiency of work. Many tunnel collapses have been reported to occur because of lack of appropriate information, such as the geological conditions ahead of the tunnel face. One of the methods which can identify rock mass conditions is the application of drill monitoring data obtained from blasting drill holes, which can detect abrupt and unexpected changes in ground conditions, geological structure and the mechanical and physical properties of rock mass. This paper presents a new approach to how drill performance parameters can be used for prediction of geological conditions ahead of tunnel face. The predictions are based on monitoring the drill parameters of instantaneous advance speed, torque and tool pressure. In order to assess conditions ahead of tunnel face, tunnel seismic profiling (TSP) and a horizontal boring investigation were undertaken and the obtained data compared to the drilling data. The predicted results using drilling performance parameters correlated well with geological conditions ahead of tunnel face.

Jan 1, 2008

By Hoffmann CF, White NC, Tedder IJ, Wood DG

Since the discovery of Pajingo in 1984, the northern Drummond Basin has emerged as a significant new gold province, and has become the focus of intense exploration for epithermal gold mineralisation. Prospects in the Conway area are hosted by felsic to intermediate lavas and volcaniclastic rocks near the base of the Drummond Basin sequence. These Drummond Basin rocks appear to represent favourable hosts to mineralisation because they are cut by structures which could have focussed and channelled fluids on a regional scale, and because they constitute a possible source of gold and, perhaps more significantly, sulphur for the transport of gold. Prospects in the Conway area are up to 15 km2 in area, and are of the adularia-sericite type. They illustrate many of the classic features (siliceous sinters, alteration mineralogy, and fluid characteristics) recognised in epithermal deposits. K-Ar dating of sericite alteration in three of the prospects has produced a range of ages from 283 to 334 Ma, suggesting that the systems are the product of multiple hydrothermal events.

Jan 1, 1990

Mineralisation adjacent to Herberton occurs within three main subcentres. The Her- berton Hill subcentre is characterised by the association of Sn,W the Herberton Dividing Range South subcentre by Sn, and the Herberton Dividing Range North by Cu, As. The relation- ships between the subcentres are discussed in terms of metal distribution, production, deposit types, wall rock alteration and re- lationships with granitoid intrusives. The temporal and three dimensional spatial re- lationships between the centres are uncertain.

Jan 1, 1978

By A E. A Northcote

The drive to maximise performance, reduce maintenance times, improve safety of operation and maintenance on mining equipment while keeping both operational and capital costs down has provided good nourishment to the creative thinking of designers of skip loading facilities for hoisting systems. Early systems were as simple as manual loading which evolved into a surge bin feeding a skip through a chute finally maturing into a measuring flask discharging into a chute to feed the skip and more recently high capacity skip feed conveyors. This paper will compare the concepts of the skip loading flask and the skip loading conveyor systems over a range of winding distances and hoisted tonnages. The comparison will draw on actual installations and review operational, maintenance and safety. An order of magnitude capital cost estimate will be used to complete the financial comparison. This will enable the reader to understand the concepts and costs and assist in selecting the appropriate skip loading system.

Mar 21, 2011

By Lu Fujun, Chen Xuewei

This paper will analyse the cause-effect relationship of the main factors influencing the production of the fully-mechanised coalface by mainly using the basic system dynamics theory. On the basics of the analysis, the simulated model of the sy

Jan 1, 1998

All companies and individuals who embark on a business venture incur costs. For the most part these costs can be conveniently categorised, firstly into capital and operating costs and then into the various elements of these major cost centres. Although the nature of expenditure naturally differs as between industries certain broad cost types are characteristic of all heavy industries. The capital costs of gaining access to an orebody, equipping a new mine, building a treatment plant and perhaps refining and smelting facilities are likened to capital expenditure by a manufacturer on new plant and equipment required for an expansion or new product innovation. Similarly the day to day costs of labour and materials employed in the running of a mining operation can be likened to similar costs in other heavy industry. There is another group of costs that are not so easily categorised. Most industries incur unavoidable costs that do not form part of the direct or capital costs of physical production. These costs include taxes and other payments to government and research expenditure. The mining industry has a particularly heavy burden of non-production costs and it is the objective here to highlight and analyse a few of them. These costs are exploration expenditure, infrastructure expenditure, royalties and income tax. This is not to suggest that these are the only major non-production costs that the mining industry needs to bear. The industry may incur significant costs for environment protection, land tenure maintenance and on liaising with Government on a wide variety of matters. It is for reasons of subject manageability that the list is confined to the four costs mentioned. For the mining industry, exploration and infrastructure expenditure, royalties and income tax have several distinguishing features. Firstly, they are generally proportionately large costs. Exploration and infrastructure expenditure for example, could well exceed mine development costs. Depending on how royalties are levied, they may be very high in relation to profits earned and many in fact exceed profits. Secondly, except for income tax, they are costs that are generally not payable by other industries. Exploration expenditure is in some respects comparable with industrial research and development. However, because mines are wasting assets exploration is necessary for survival, and it is likely to form a larger part of costs per dollar of profits or sales than R&D. It can therefore be said that exploration is of far more significance to the miner than R&D is to the typical industrial company. Furthermore, unlike exploration expenditure, R&D results are transportable and patents permitting, transferable. The infrastructure burden that miners must carry is unique to the industry. Whereas urbanised industry is not usually liable for the capital cost of power, water, transport, townships and community facilities, the miner must finance these projects himself. Neither the payment of royalties, nor of course, income tax are unique to the mining industry. Royalties are more properly described as a unique charge on some primary industries but however described, they are a charge that manufacturing and service industries do not have to pay. Whilst we all pay income tax, the mining industry's uniqueness derives from the special problem that the industry has in arriving at annual net income in view of the capital intensity of the industry, partly due to expenditure on infrastructure, the indefinite life of capital equipment and its unpredictable residual value, funds expended on exploration and long lead times associated with a mine development. The third distinguishing feature of these costs is that, with the possible exception of exploration expenditure, they are heavily influenced by the policies and actions of Government. As such the industry has a responsibility to promote the industry by emphasising its potential to improve national product including exports and by requesting that the Government provide for the industry in its long term planning and seek its co-operation to prevent the industry incurring inequitable penalties relative to other industries.Finally, exploration and infrastructure expenditure are significant because they are front-end charges on a project. When due allowance is given the time value of money and the deferment of income from a mining development to which they relate, exploration and infrastructure expenditure assume greater importance than the raw money expenditure suggests. For all these reasons, exploration and infrastructure expenditure, mining royalties and mining income tax are worthy of detailed study. This is the purpose of this paper. The objective is to examine the determinants that give rise to them and provide some thoughts on their impact on on-going and potential mining developments and, where relevant, to make some suggestions as to how they may be minimised.

Jan 1, 1977

By Haeussler P, Christie A, Bradley D, Skinner D

Mesothermal gold deposits of southern Alaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat was produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

By B Lyne

In 1990, the Queensland mining industry had come to the conclusion that new safety and health legislation based on risk identification and control was required if the mining industry was to be effectively and efficiently regulated. In particular stakeholders in the coal mining industry had arrived at this opinion after the industry had suffered a number of major underground explosions over the 14-year period between 1972 and 1986. Also by 1990, a general consensus had emerged across both the coal and metalliferous mining sectors that mining industry was over regulated and, more to the point this over regulation did not encourage industry to identify and address the underlying causes that had led to a cycle of major mining accidents in the state. The prevailing opinion was that the prescriptive legislation left the ownership of risk management with the regulator and not with the mine operator. This paper discusses the background to the development of the Queensland Coal Mining Safety and Health Act 1999 and the Mining and Quarrying Safety and Health Act 1999 and the progress made in improving safety and health since the statutes came into force on the 16 March 2001. The paper discusses the issues that had to be addressed during the development of the legislation including the interaction with other legislation based on based on risk management principles that either overly or interface with the mining legislation. The effect the underground explosion at Moura No 2 in 1994 had on the final content of the new legislation is also considered. Health is often the neglected twin of safety and health legislation and the paper previews the health surveillance system being proposed in Queensland to ensure that health of mine and quarry workers is afforded the same priority as their safety. By increasing the structured management of occupational health problems in our mines there is an opportunity to make significant improvements in mine safety In conclusion the paper reviews the results to date since the introduction of the new mining safety and health legislation in Queensland on the 16 March 2001. Progress has been made and more is yet to be achieved

Jan 1, 2003

By AJ LYNCH

Broken Hill metallurgists have been responsible for some of the most important developments in mineral processing technology. These occurred mainly in two periods, 1902 - 15 and 1955 - 70. Mineral flotation was developed as an industrial process during the first period and this happened in two stages, the recovery of zinc minerals from the tailings dump accumulated during the gravity concentration of the oxidised ores and the selective recovery of galena and marmatite during flotation of the primary ores. During the second period fast accurate analytical procedures were developed to provide rapid assessment of process performance, and new means of controlling the process were devised which improved throughputs, grades and recoveries. These technological successes were due to the skills of the metallurgists and the commitment of the companies. They brought large financial returns. They were achieved under difficult circumstance. There are important lessons to be learnt from these successes.

Jan 1, 1992

Accident control has been a pre occupation of progressive industrial and mining companies for many years but few have attempted more than direct injury control. In recent years, particularly in North America, analyses of accident costs have shown that material damage resulting from accidents is usually of greater economic significance than injuries and this has led to the concept of loss control. Loss control is an attempt to take the emphasis off injury prevention and to concentrate on the basic factors which affect both the health of the individual and of the company. The deterrent to greater acceptance of this philosophy has been the apparent diffi- culties of implementing a loss control programme but Associated Minerals Consolidated Limited has adopted a simple approach. It has had a minimum disturbing effect on normal operations because existing systems have been modified to provide the new information required. It is suggested that the programme outlined is applicable to other mining ventures and is a practical method of providing benefits for both the company and its employees.

Jan 1, 1975

In order to achieve optimum results for money spent in construction of new projects there is a need for mining developers to pay greater attention to cost control. Control is achieved by establishing a frame of reference, a method of checking and a means of remedial action. The frame of reference is a well coded set of budget estimates which graduate into definitive estimates as design is completed, backed up by drawings, specifications and bills of quantities. The method of checking is provided by cost engineering and quantity surveying input, at both feasibility study and design and documentation stages. Remedial action follows if the checking process reveals a need. In large complex projects where construction completion time is often of prime importance, control of costs can sometimes be relegated to second place. To avoid this it may be necessary to include specialists in cost control in project management teams. Quantity surveyors are trained specifically in construction economics and can provide develop- ers and project engineers with valuable support at all stages of construction.

Jan 1, 1983

By J Walasiak

In the climate planning of mines and tunnelling with anticipated poor climatic conditions, and especially in case of longer working shifts, the main question is whether it can be reliably prevented that certain climatic limits laid down be exceeded. Working at high temperature and/or humidity can lead to reduced human working energy û a very important economic aspect û and to a risky lack of concentration on the part of the miners or to heat collapse and extremely dangerous heat stroke. With the Deutsche Montan Technologie GmbH (DMT) climate prediction programs, both the dry and the extremely significant humid heat transfer can be calculated. This is due to the high planning reliability involved. With the help of these climate prediction programs it is already possible to determine the anticipated climatic values for the operation phase as early as the planning stage of new ore or coal fields or of tunnel construction projects and to design the optimum air cooling system for every underground project with due regard to technical and economic aspects.

Jan 1, 2005

Mine geologists have access to an economic mineral deposit, production parameters and secure exploitation title. They are well placed to understand ore formation and should contribute to the effective exploration of company mine property. Application of their special skills has been curbed by pre-occupation with production duties and by company re-engineering, including staff reductions. Contributions to exploration have been diminished and personal development inhibited. Modified management is required. Participation in mineral system studies and in exploration research comprise part of the basis for the re-emergence of mine geologists on the exploration scene. Changes in investment strategies in the minerals industry may create new employment opportunities. With regard to estimation of resources and reserves, the competence of practitioners who are incapable of disclosing their methods in transparent terms is under question. Ethical standards are also under public scrutiny because of some notable malpractice. Independent auditing may hecome more intrusive. While understandable in a market context, it reflects poorly on the profession. More substantial effort in public communications can improve the credihility ofthe industry and equip practising mine ceolouists for snider responsihility.

Jan 1, 1997

A series of physical tests have been conducted to determine the actual performance of bunton to shaft side wall connections typically used in new shaft construction in South Africa. The test set-up is described, together with the applied loading, which incorporates a cyclical load component and a quasi-static load component, in an attempt to simulate actual conditions in the shaft. The test results are given and it is shown that generally the performance is adequate, provided double-slotted holes are not used. Generally the fatigue performance is found to be good, with the only exception being cases where the bottom of the bunton is lower than the seating level for the bunton to side wall connection. Arising from the tests, typical design values of connection stiffness, strength and fatigue life are proposed and a design procedure including these three key aspects of connections is described.

Jan 1, 2005

By E Jak

A viscosity model has been developed for both completely liquid and heterogeneous, partly crystallised slags in the Al2O3-CaO-æFeOÆ-SiO2 system in equilibrium with metallic iron. The Urbain formalism has been modified to describe the viscosities of the liquid slag phase over the complete range of compositions and a wide range of temperatures. The Roscoe equation has been used to describe the effect of presence of solid suspension (slurry effect) on the viscosity. The parameters of the viscosity model were optimised to describe large experimental data set in the low-order subsystems, as well as in the multi-component system. The computer package FACT was used for prediction of the proportion of solids and the composition of the remaining liquid phase. The model provides a good description of the experimental data (over four thousand experimental points) in liquid phase, and liquid + solid mixtures, over the complete range of compositions and a wide range of temperatures. This model can now be used for viscosity predictions in industrial slag systems. An example of the application of the new model to slag cleaning and reduction smelting processes is given in this paper.

Jan 1, 2000

Almost all industrial products, such as buildings, cars, plastics, railways, radio and television sets, computers, and others are made from materials extracted from the Earth. Earth is main resource of energy and up to now; the energy has been derived mainly from natural resources. Mining industry has significant influence to the nature, sometimes evokes a devastation of nature. On the other hand we have got a lot of nice examples that good preparation, sensitive mining practice and consistent reclamation can minimise the negative effects. All the mentioned problems calls for effective tools for mine design, mine operation and mine reclamation. Third millennium brings next challenge given by advances in information and communication technology. The development of very sophisticated software tools provides to technical systems some features of autonomous æthinkingÆ and intelligent behaviour. We can find large effort and a lot of scientific papers reflecting last advancement in science and technology and providing inspiration for new mining technology of third millennium called Intelligent Mine. Some aspects related to creation and utilisation of æIntelligent ModelsÆ as a background of æIntelligent MineÆ are presented and discussed in this paper.

Jan 1, 2003