Search Documents

By Warner N. A

There is an inherent problem in producing simultaneously lead, zinc and copper as metals in a single polymetallic smelting furnace. It relates to the condensation of lead and zinc from the gas phase under vacuum conditions such that metals in bulk form, either solid or liquid, are obtained as products rather than a fume or dust containing both metallic and non-metallic components. To understand this phenomenon, it has been necessary to establish mathematical models with computer simulation to identify the process requirements for effecting the objective of maximum bulk metal production with minimum fog formation. The theoretical framework of simultaneous heat and mass transfer involved in condensation from gas mixtures containing a non-condensable gas has been extended to the high temperature and reduced pressure conditions. These apply to new technology for polymetallic smelting now being developed in a project currently funded jointly by the Commission of the European Communities and the Mineral Industry Research Organisation. Under the right conditions it is theoretically possible to condense out both lead and zinc with minimal fume formation, but in all practical cases it is anticipated that some circulating load for reversion back to the smelter will be needed.

Jan 1, 1989

By R Piper

The Yabulu Nickel Refinery commissioned in 1974, processes lateritic ore via a modified Caron process to produce high quality nickel and cobalt products. The Greenvale orebody provided the sole source of feed to the plant until 1990 and with well-blended mineralogy, it resulted in stable and predictable plant performance, allowing the operating focus to be on reducing energy consumption and increasing ore throughput. This approach provided better economics than pursuing increased reduction efficiency. From 1990, increasing quantities of lateritic ore were imported from Indonesia, Philippines and New Caledonia. This introduced considerable variation in ore blends and instability in plant operation but also provided the opportunity to treat higher grade ore blends which yielded higher reduction efficiencies. Ore reduction is conducted using 12 Herreshoff multiple hearth reduction furnaces, using heavy fuel oil as reductant. The æROASTERÆ Project was approved in November 2000 with the primary objective of improving Nickel reduction efficiency by: Stabilising Roaster Operation via a structured program including focused maintenance efforts, capital equipment upgrades, new process measurements, process re-design and improvements to operating skills and process troubleshooting. A structured technical program including laboratory and plant studies using one plant furnace as a pilot unit to develop improved knowledge of how the reduction process proceeds in the Herreshoff furnace. Armed with this knowledge, optimised process conditions and a reduction process model were developed contributing to a significant demonstrated reduction efficiency improvement. Technical input to the project was provided by QNI with Hatch providing the engineering and project management for the $8.5 M capital work. Execution of the work included extensive consultation with the plant operators and close cooperation between the Hatch project team and QNI operations personnel ensuring installations were completed with minimal production disruption. A strong focus on safety management resulted in a number of brownfields project relevant safety initiatives being implemented resulting in project completion without a serious injury.

Jan 1, 2002

By E Topal

There are presently no suitable underground mine production scheduling optimisation models available for application to sublevel stope mining. Scheduling underground production for maximum return is therefore still a manual process, which generally involves scheduling production from the next available highest cash flow stope within the operational constraints of the project. In most mining operations, the scheduling problem is too large and complex to guarantee truly optimal results through manual scheduling. This paper reviews some general optimisation studies that have been proposed for underground hard rock mining. Furthermore, an example of a mixed integer programming model is presented for a small conceptual sublevel stoping operation. Comparative results of a schedule generated by a mixed integer programming (MIP) production scheduling model and a manually generated model on a nine stope example is presented. Results indicate that the potential benefits of the MIP production scheduling model for the purpose of maximising NPV are significant. Finally, a new constraint was formulated to limit multiple exposures of fill masses for use in an existing MIP production scheduling model. Testing of the formulation took place on the central stope of the nine stope example, which showed that the formulation performed its task without breaking other operational constraints.

Jan 1, 2007

As defined by both the Australian and New South Wales Governments the Illawarra consists of the Tablelands, the Local Government areas of WingecarribPe Shire, Bowral Municipality and Mittagong Shire, the Wollongong sub-region consisting of Wollongong City Council, Shellharbour Municipality and Kiama Municipality and finally the Shoalhaven Shire. I intend here to concentrate on community development in the Wollongong sub-region.

Jan 1, 1976

The paper reviews winder rope inspection procedures at the Non Destructive Testing (NDT) Unit of Western Australian School of Mines (WASM) and outlines measures taken to adopt the world's best practice. The measures include acquisition of a new type of rope tester, adoption of comprehensive rope rejection criteria, adoption of a standard rope inspection procedure and formal training of the wire rope inspectors.

Jan 1, 1995

By E Haren, A Winchester

The CSA Mine has a long and varied history from initial discovery in 1871 through to the present. Lead-zinc mineralisation was mined historically near the surface. Today copper and silver are extracted from the deeper regions of the mine. The mine has passed through a number of owners over this time, each with a unique operating philosophy and understanding of the mineralisation. Cobar Management Pty Ltd re-opened the mine in 1999 and has undertaken extensive drilling programs to expand the resource and gain a better understanding of the mineralisation characteristics. Presently mineralisation has been located over a strike length of 1.2 km and to a depth of over 2.0 km with over 30 mineralised lenses from four identified ore systems. The refinement of geological and mineralisation models led to further discoveries and prompted a review and modification of resource modelling processes. Advanced statistical analyses prompted the implementation of ordinary kriging as a grade estimator. Improved stationarity from enhanced geological domaining has been supported by variography and kriging neighbourhood analysis studies. Resource models at CSA are now quantifiable in terms of mineralisation style and estimation reliability. The new techniques are assisting the definition of more mining fronts, which are creating new opportunities to increase mine output.

Jan 1, 2006

By M R. Davidson, M P. Schwarz

A model for column bioleaching is investigated to identify and understand aspects of bacteria in bioleaching applications, which have implications in heap bioleaching operations. The model is used to simulate scenarios that would otherwise be time consuming to perform experimentally. This study uses a model of bacterial transport and attachment/detachment to ore particles, with a bioleaching model for the depletion of a copper-sulfide, also accounting for liquid and gas flow and gas/liquid oxygen mass transfer. The model includes aspects such as oxygen and ferrous ion consumption, coupled with leaching of a copper-sulfide via the shrinking core model. The model is used to investigate how the rate of leaching is affected by the bacterial concentration in the columns, by the bacterial regeneration of the leaching oxidant ferric ions. The model is also used to assess the impact of oxygen limitation and inoculation method on the copper leaching. Some comparison of the model with experimental data will be shown.

Jan 1, 2004

By R Kahnt, S Jahn, D Baacke, M Eckart

Relocation into the Lichtenberg open pit mine of about 110 million m3 of sulfide-bearing and ARD-generating waste rock piled up on the surface is the most important and cost-intensive single surface restoration project conducted by WISMUT GmbH at the former Ronneburg uranium mining site. The waste rock comprises for the most part Palaeozoic shales, limestones and diabases with pyrite contents of up to seven per cent. Waste pile relocation began in 1992 and is scheduled to be completed by 2007. The approach used for relocation has been extensively described elsewhere (Jakubick et al, 1997; Hockley et al, 1997; Chapman et al, 1998; Paul, 2003). Following completion of the backfill that will be up to 60 m above the initial ground level, a dry cover will be placed on top of the backfilled mine wastes. The area to be covered amounts to about 220 ha. Design planning for the final cover placement of which is to begin in 2004 had to be based on a comprehensive cost-benefit analysis over and above compliance with legal requirements. The crucial question to be answered in this respect was to determine û in addition to the expenditure required to ensure reuse, radiation protection and soil protection û the extent to which additional time, effort and money were justified in order to minimise contaminant release from the unsaturated portion of the backfilled pit contributing to total releases into the ground water and possibly achieve savings in long-term operating costs for the on-site water treatment plant. Optimisation was based on contaminant balance modelling for the entire site reproducing dominant physical and geochemical processes. Among the specifics underlying the cover design is that contaminant release from the backfilled open pit must not be considered independently of that from the adjacent flooded underground mine and that a major part of the backfilled open pit will also be submerged. Following weighing of cover-related short- and long-term costs it was found that higher construction costs for the various cover options will not be offset by cost savings in the long-term water treatment. As a consequence of pit flooding, even a costly multiple cover including an impermeable layer will only insignificantly impact on concentrations and loads at ground water spill over points. As a result of comprehensive studies and investigations, a combined cover of cohesive soil material from on-site excavation overlain by a 0.4 m thick storage layer to restore natural soil functions for revegetation was derived and submitted for approval. Together with hydraulic measures, this approach is to meet any requirement in terms of radiology, water protection, stability, erosion protection, and reuse.

Jan 1, 2003

A Presidential Commission of Enquiry into the conservation of South Africa's coal resources was appointed in 1970. This Commission, in co-operation with the Chamber of Mines of South Africa, established a national inventory of South Africa's in situ and extractable resources and reserves of coal of various types and grades by several mining methods. South Africa's future demand for coal by all market sectors and the specifications of coal required, were also established by means of econometric models. A comparison of potential supply and anticipated demand indicated serious defi- ciencies of certain types of coal and the need for the conservation of others. This paper describes recommendations for alternate strategies for the optimum utilization of available resources. Con- sideration was given to various policies relating to pricing, exports, taxation and incentives, and to the possibility of the substitution of higher grades of coal by lower grades. The steps so far taken to develop a national coal policy in South Africa are described.

Jan 1, 1977

By Jelenich L, Murray J. Rantanen J

The experience gained in the development of an Operator Guidance System (OGS) for on-line process control and fault diagnosis in a commercial scale sintering process will be discussed in this paper. The OGS development started with the specification of feasible control and support tasks, eg ratio control scheme, mass balance calculations. Next, minimum requirements for fault diagnosis and process control were defined and the adequacy of existing instrumentation was assessed. The OGS knowledge base consists of both quantitative and qualitative diagnosis methods. Quantitative models based on fundamental engineering principle are used first and any gaps in such quantitative knowledge are then filled with heuristic rules. The diagnostic rules for the knowledge base was developed based on the knowledge acquired from experienced operators and operations engineers and validated with plant data. A real time reasoning program was written using C language and data base software. The OGS has a human-computer interface which is the primary means of interaction between the OGS and process operator. The OGS development has been successful in assisting operators in decision-making in their routine tasks. Further enhancement to the existing system is currently underway.

Jan 1, 1995

By J C. Furness, F S. Cannon

Metal casting operations are a significant source of hazardous air pollutants. In particular, high production iron foundries emit significant quantities of volatile organic compounds (VOCs) during pouring, cooling and shakeout of iron castings made in green sand molds. End-of-the-pipeline capture and destruction methods to reduce VOC emissions add crippling costs to foundries. Alternately, the incorporation of advanced oxidants (AO) into metal casting green sand systems has been shown to reduce emissions from high production iron foundries in the US, and at the same time reduce operating costs. Cost savings are driven by the benefits of AO in clay recovery systems. Emissions reductions are the direct result of cascading AO-based reactions taking place in green sand molds. This sustainable greening of the metal casting process is a prototype for the development of other AO and non-AO process-based solutions for sustainable high temperature processing of materials. Fundamentals of AO technologies will be discussed along with the performance characteristics of AO processing systems in the metal casting industry and the breadth of other processing and remediation applications for which AO technologies have the potential to be successfully employed.

Jan 1, 2002

SPOT imagery acquired in May 1986 of the areas that include the Dugald River lead-zinc lode, northwest Queensland, Australia and the Ngwenalekau copper deposit, Botswana has been evaluated and compared with LANDSAT MSS imagery of the same areas. The data have been processed using band combinations, band ratioing, principal components analysis and classificatory techniques and the outputs compared with those of geobotanical, geochemical and biogeochemical data as well as geological information. For both study areas the image processing techniques cited have successfully distinguished discrete vegetation associations related to discrete surficial and bedrock geological units; and, notwithstanding the sharp contrasts between the nature of the geobotanical anomalies that in both areas occur over mineralised bedrock in Proterozoic sedimentary sequences, they have successfully identified the areas of anomalous vegetation over the mineral deposits. Greater vegetational and geological detail is revealed than on outputs generated from LANDSAT MSS data [see Cole, 1977, 1982(a) and (b)]. The additional information yielded by SPOT imagery compared with LANDSAT MSS imagery results from its greater spatial resolution - 20 metres as against 79 metres - and from ti fact that the three SPOT MSS spectral bands - 0.50 0.59um, 0.615-0.68um and 0.79-0.89um - respectivelc cover those sections of the electro-magnetic spectrum in which leaf pigments, notably chlorophyll, absorption for photosynthesis and leaf cell structure strongly influence reflectance. This accords opportunities for the detection of reflectance aberrations caused by stress due to drought and/or metal toxicity as well as for the identification of anomalous vegetation communities of moderate sizr These cannot be accurately discriminated on LANDSA I MSS imagery on which only very large geobotanical anomalies like that over the Lady Annie phosphate deposit in northwest Queensland [Cole, 1977, 1984; Cole and Owen-Jones, 19771 can be detected.

Jan 1, 1988

By Woods PW

Consulting Engineers have been used in the mining and metallurgical industries for many years. The traditional role of the consultant overseas has been one of assisting with conceptual design right through to con- struction and commissioning as well as on occasion acting solely in specialist fields. This role developed because mining companies wished to concentrate on building up the permanent organisation they require to operate their mines and treatment plants without the traumas of increasing staff for the design and construction period and reducing it on completion. In Australia where there have been few individual minerals projects of magnitude (until recently) companies have looked after their own detailed engineering and construct- ion management employing consultants mainly in specialised fields.

Jan 1, 1975

By McDonald K. J, Flann R. C

A liquid phase sintering (LPS) process for preparing basket anodes from nickel powder has been scaled-up and the innuence of compact green density and sulphur content, as well as sintering conditions (period and syngas now.rate) on the perfonnance of anodes has been evaluated. The product anodes have been tested in an industrial electroplating tank. It is concluded that if anode residues are to be minimised, then with a sintering temperature of 960"C, compact green density needs to be as high as economically achievable (85 - 87 per cent density of solid nickel) and the sintering period approximately 40 minutes. With these constraints, if residual sulphur contents of anodes are to be kept as low as those of commercial anodes, then the sulphur content of the green compacts would need to be less than 1670 ppm. At the same time, it is also found that residual sulphur concentrations as high as 2000 ppm are beneficial to anode pcrfonnancc and not detrimental to the quality of the electroplate. The ability of the LPS process to produce marketable nickel anodes for the electroplating industry is clearly demonstrated.

Jan 1, 1993

By Smith G. A

The scope and complexity of the Melbourne Underground Rail Loop Project and the budget restraints on the planning, design and construction of the works necessitated sound manage- ment procedures for control and co-ordination. Project Management Procedures formulated by the Principal Consultant to the Authority, John Connell - Mott, Hay 9 Anderson, Hatch, Jacobs, ensured that the Authority retained overall control of the project at all times.

Jan 1, 1981

The advancements achieved in rapid tunnelling in the 60's and 70's have been notable. It is unfortunate that shaft sinking has not enjoyed equivalent advances and there are many good reasons why this is so. Technical and commercial considerations have held back development and continue to do so despite the increasing urgency in the search for minerals and energy. By the careful selection of an appropri- ate project and the application of specialist engineering the Bdard took advantage of a unique opportunity to apply a mechanised shaft borer in field conditions.

Jan 1, 1981

By N Ross, N Goldup

In recent years the heavy mineral mining industry has started to look more closely at the feasibility of mining moderate to high slimes deposits. During the initial stages of orebody evaluation the primary purpose of the pilot plant is to produce heavy mineral concentrate for metallurgical evaluation. Hence, generally little consideration is given to the disposal of the waste material (slimes and tailings). This paper suggests additional, simple, low-cost, tests that can easily be incorporated into an initial pilot plant operation. With this data a more definitive evaluation of available waste disposal options can be made during the early stages of the project. Thus, permitting better project focus and utilisation of resources. These tests include free settling of slimes, natural slimes drying and consolidation (undrained and drained), tailings stacking angles, and particle size distributions of input and waste streams, etc. The objective and method of each test is summarised, together with its relevance to possible waste disposal options. The results of this preliminary testwork can later be used to expand upon and define further tests for the second phase of pilot plant operations, which will enable a more definitive evaluation of a proposed waste disposal solution.

Jan 1, 2001

By R Valenta

Most developing projects face a range of technical and non-technical challenges, and examination of development histories can potentially provide insights into improved approaches to project development. The Kestanelik project in the Canakkale region of Western Turkey was acquired by Chesser Resources Ltd in 2008. Turkey is a significant and growing source of gold production, with sector participation by both domestic and international companies. While the broad ranges of challenges faced by developing projects is well known, there are relatively few case studies in which the range of technical, environmental, social and governance challenges are presented in a single contribution. Recent studies of undeveloped complex orebodies have particularly shown the extent to which environment, social and governance (ESG) complexities contribute to project delays and failures. The Kestanelik project faced a full range of technical and ESG complexities, and provides an illustrative example of the associated challenges. CITATION: Valenta, R, 2018. A case study of technical, social and environmental challenges for a gold project development in Western Turkey, in Proceedings Complex Orebodies Conference 2018, pp 73–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A J. MacDonald, M P. Raffield

The South Deep massive orebody consists of 20 to 30 m of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 m and 3400 m. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse various scenarios to aid in the decision process.

Jan 1, 1998

By Mazandarani M, Chabot L, Vichion K

Pitch-steering models have been developed for discretely advanced mining machines (such as heading machines and coal shearers) using small-angle geometry and there are illustrative examples of simulator predicted performance. Although simple linear models result from the analysis of open-based machines, sledge mounted machines require execution of a Linear Programming energy minimisation to determine the attitude of the machine base at each advance over the previously cut floor steps. An analytical approach is based on elastic beam concepts developed for such applications as longwall face conveyors, caterpillar tracked machines such as continuous miners and longhole drills. Simulation results for longhole drills show the expected performance of an automatic guidance system and the destabilizing effects of sensing deviation too far behind the drill bit. Certain drill bit boundary conditions are expected to assist TBM. steering studies in three dimensions.There is a real role in mining machine steering for the mathematical models used in flight simulators.

Jan 1, 1991