Search Documents

By Spencer P. A

Bacterial oxidation, previously known as bacterial leaching or bio-leaching, has been applied at laboratory and pilot plant scale to many refractory ores and concentrates around the world. The most common bacterial culture used in this process has been Thiobacillus sp. This organism is limited in commercial application, especially in Australia for several reasons. The optimum operating temperature range for this culture is 30¦C to 40¦C and high levels of some metals such as arsenic, silver, and copper have toxic effects on the culture thus reducing its effectiveness. The culture employed by BacTech (Australia) Pty lid is a moderately thermophilic culture which operates in a temperature range of 40¦C to 55¦C (which is more amenable to the Australian climate) and with higher resistance levels to metals often found to be toxic to Thiobacillus sp..

Jan 1, 1991

The gas drainage characteristics of two seams, the Bowen at Bowen No. 2 Colliery, Collinsville, and the Gemini at Leichhardt Colliery, Blackwater, are assessed. Single borehole tests and drainage panels were studied by underground monitoring of pressures and gas flows. Permeability was found to be effected by cleat to an order of magnitude. Other structural features are shown to be important. In this context, the need for delineation of no-flow zone locations in boreholes is shown to be of great importance where in-seam pre-drainage is being used for outburst control. Water in the seams strongly influences permeability causing gas flows to fluctuate with time. Use is made of modified reservoir engineering techniques to analyse the drainage characteristics of seams.

Jan 1, 1982

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Wright R, Stock E. C

The Windarra nickel deposits known to date comprise two sulphide orebodies located at Mount Windarra and South Windarra. These orebodies, which are 15 km apart, lie within an ultramafic complex at or near its footwall contact with a banded iron formation. The Windarra deposits are 270 km north-northeast of Kalgoorlie in West- ern Australia which was the centre of a major nickel exploration programme fol- lowing the discovery of nickel deposits at Kambalda in 1966. Surface indications of the Mount Windarra orebody were discovered in 1969 by Mr. Ken Shirley while prospect- ing the Laverton area for Poseidon Ltd. (then NL). The mineralisation was loc- ated by systematic prospecting for goss- anous material associated with aero-mag- netic anomalies and ultramafic rocks. The South Windarra deposit was dis- covered in 1971 by the Union-Hanna- Homestake Joint Venture, by exploring along the strike extension of the mount Windarra ultramafic-banded iron format- ion contact. A detailed ground magnet 1. Acting Operations Superintendent, Windarra Nickel Project, Windarra, W.A. 2. Senior Geologist, Windarra Nickel Project, Windarra, W.A. 3. Mine Geologist, Windarra Nickel Project, Windarra, W.A.

Jan 1, 1973

By T E. Norgate

Salinity in Australia is caused by over irrigation and land clearing for agricultural use over the last 100 years. It is now the biggest threat to the quality of land and water in the Murray Darling Basin and Western Australia. Pumping the saline waters straight into the ocean or transporting the solid residue (mainly sodium chloride) to the ocean after evaporation of the water is expected to cost the taxpayer millions of dollars every year. This paper proposes that the salinity problem of Australia, at least in part, can be converted to an asset rather than a liability if it is exploited and used to make value-added products. The more value made out of saline waters, the more saline water is processed and therefore the more salt is extracted from the land. The value-added products that can be made out of saline waters are numerous and diverse. Rough calculations show that value addition to the saline waters could potentially generate up to $A 200 million per annum business in the Murray-Darling Basin. Although it is a challenge to make cost competitive products and find markets for these products it is possible that up to $A 100 million per year may be gained from import substitution. Value addition to salinity would also reduce the threat on the environment and existing agricultural industry. Investment to add value to salinity will create business in the region, nurture the local small population communities, and increase services and long-term employment.

Jan 1, 2002

By J McQuie

The concentrator at WMCÆs Leinster Nickel Operation has operated with flash flotation in the grinding circuit since the early 1990s. There has always been a positive correlation between flash flotation Ni recovery and overall Ni recovery û however this relationship could be explained by differences in the ore, rather than by the action of the Flash flotation cell in reducing overgrinding of Ni. In July 2003, refurbishment within the plant made it necessary to operate the concentrator for a period with the flash flotation cells off. The resulting data set provided evidence that flash flotation in the grinding circuit changes the size distribution of Ni to reduce the amount of slow-floating fine (-7 ¦m) Ni produced. Ni recoveries in the finer size fractions were similar with flash flotation on or off û but because less fine Ni is produced when the flash flotation cells are operated, overall Ni recovery improved.

Jan 1, 2005

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

By Coombes J, Richards W. L

The objective of this paper is to illustrate, in a practical way, how both geologists and mining engineers can use conditional simulation to add value to their decisions. Inherent assumptions, requirements and essential components of condition

Jan 1, 1998

Woodlawn Mines began underground operations in 1986. At the time of going underground it was envisaged that there would be no 'contract' payment to the underground employees. This was a relatively unique step to make, especially as most major underground mines in Australia relied heavily on the contract system to motivate their workforce. (Obviously with varying degrees of success.) Woodlawn faced the task of motivating their employees through a multi-skilled system with a great emphasis on leadership and a genuine care for their employees. The 'proof of the pudding' is that Woodlawn has not lost any time over industrial issues since beginning underground operations in 1986. To achieve success in any operation the organisation must not only be advanced in its management principles but also be prepared to be innovative in the way it deals with physical problems, ie ground control, equipment selection and maintenance. Difficult ground conditions at Woodlawn have necessitated the deployment of two Cabolt Jumbos and the construction of cost-effective shotcrete systems. The shotcrete system now being built has been tested in a prototype form and is proving to be a safe and simple way to manage weak, low stress friable ground. Although the ground at Woodlawn has low stress component by virtue of the fact the ore can have a density of 4.5dm3, cable dowelling has become a necessity. The two cable dowel jumbos install high quality reinforced cables. The pressure of 'production' means that these machines must be consistently available for use and the training of maintenance personnel and operators ensures that a maximum of cable dowels can be installed over any given time span. In any modem mine ventilation is a primary concern and the major area of concern comes from the vehicles themselves. In our recent replacement for the standard 'Toro' loader, three engine options were considered. A relative newcomer to underground mining was accepted. The Detroit 60 series (DDEC) engine came with a great reputation and has lived up to this. The engine has an electronic management system that reduces particulates to a hardly visible minimum, provides great amounts of engine power and reduces fuel consumption by approximately 45 per cent. The operational benefits of such an engine are worth sharing through this conference.

Jan 1, 1995

By de Lassar de Pressigny Y

IRSID has in its laboratories two experi mental counter-current reduction furnaces allo- wing the simulation of the physico-chemical conditions of reduction in any gas-solid coun- ter-current process, including the blast furnace and direct-reduction shaft-furnaces. The counter current is realized by an electric furnace mo- ving along a laboratory tube filled with the material to be tested. The reducing gas stream in the tube travels in the same direction as the furnace After reduction, twenty samples, with dif- ferent degrees of reduction and which can be related to different levels of an industrial furnace, are taken from the tube and subjected to various quality tests. Experiments were realized to determine the behaviour of various types of industrial pellets when reduced under either blast furnace or shaft furnace conditions. The results show the large influence of the reducing conditions on any pa- rameter characteristic of the quality of the pellets : reduction efficiency, swelling, cru- shing strength and disintegration.

Jan 1, 1974

By Hocking G

For some underground structures, the use of the plane strain assumption in stress analyses may not be justified. The finite element method and photoelasticity have been used to obtain complete 3-D solutions, but, for various reasons, neither method has found universal use. The boundary integral equation method (B.I.E.M.) can be more efficient and economical than the finite element method for 3-D problems involving large volume to surface area ratios. A B.I.E.M. program developed for calculating stresses and deformations in infinite elastic media has been used to determine the 3-D distributions of stress around T- and Y- junctions of circular tunnels in stress fields in which the ratios of horizontal to vertical stress are 0, 0.33, 1.0 and 2.0. For the T- junction considered,stress concentrations at the intersection are approximately twice the plane strain values. Except where horizontal field stresses are high, the stresses in both tunnels approximate the plane strain values at about two tunnel diameters from the point of intersection of the tunnel centre lines. The stresses in the two branches reach those for the corresponding plane strain, two parallel tunnel case two diameters from the point of intersection of thq inner tunnel walls. Very high stress concentra- tions occur in the pillar of rock between the inner tunnel walls near the point of intersection.

Jan 1, 1976

By Cudmore JF, Rowlands D

Incidents associated with spontaneous combustion of coal have resulted in the loss of many lives and considerable capital and equip- ment. Nevertheless, the factors controlling the propensity of coal to spontaneous combustion are not clearly understood and there is a need for research to study the effects of rank, petrog- raphy, moisture contents, etc. This has been attempted in a study of the propensities of selected Queensland coals to spontaneous combustion. An adiabatic calori- meter was constructed to study the self-heating of a large number of coals. Chemical and petro- graphic analyses of the coals were determined and an attempt was made to relate these propert- ies to the self-heating characteristics of the coal. The results show a strong relationship between rank and self-heating characteristics and that petrographic composition of coal may also be of importance. Some observations on the application of the laboratory results to the practical situation are made as are recommendations for future research.

Jan 1, 1981

Tectonic subsidence plots have been calculated for well, extrapolated-well and significant off-well (seismically-based) locations in the Vulcan Sub-basin and adjacent highs (western Timor Sea). The subsidence curves have been normalized to a common datum, the distinctive "near top Permian" marker, and corrected for sediment compaction, palaeobathymetry, eustatic sea-level change and loading effects.Four principal phases of post-Permian basin development are recognised and quantitatively described by integrating the results of the sub-sidence analysis into the regional (e.g. recent Ocean Drilling Program-derived) framework of the tectonic evolution of the North West Shelf. They are1. the Triassic-mid Jurassic Westralian Superbasin intracratonic phase,2. the late Jurassic-early Cretaceous North West Shelf rift phase,3. the mid Cretaceous-Palaeogene North West Shelf subsidence phase, and4. the Neogene-present Timor collision phase. Rapid Triassic tectonic subsidence occurred in an intracratonic setting, possibly subsequent to aborted late Palaeozoic rifting. Intracratonic sub-sidence mechanisms such as deep crustal metamorphism and/or intrustion and regional tectonic compression are invoked in addition to any post-rift thermal subsidence which may have occurred.

Jan 1, 1990

By OÆBrien D. R

Up until June 1988, Mount Thorley Coal Handling and Preparation Plant disposed of tailings by two methods. Approximately half of the plant tailings was mechanically dewatered by solid bowl centrifuges mixed with plant reject and was subsequently disposed in mine overburden spoils; the remainder was pumped to tailings ponds. Both future mine planning and environmental constraints could not allow for the long term construction of more tailings ponds so, following evaluation of available dewatering technology, belt press filters were selected for the treatment of tailings in excess of the capacity of the existing solid bowl centrifuges. Commission of the four 2.5 metre wide belt press filters soon showed that marked differences in performance were experienced when treating different coal seams. Further analysis showed that the coal tailings from different seams were quite different in terms of clay mineralogy, and these differences could be correlated with varying degrees of filter performance. Poor filter performance was experienced with coal tailings rich in sodium montmorillinite clays. A number of variables were investigated including in-line mechanical mixing of flocculant and feed slurry, cation exchange reagents such as gypsum, and upstream addition of cationic flocculant. In order to achieve satisfactory performance on the worst tailings, a combination of all of the above was required. In this paper, the reasons for selection of belt press filters and the program of investigations and testwork required to arrive at satisfactory belt press filter performance for the treatment of troublesome bentonitic rich tailings are discussed.

Jan 1, 1989

Laboratory high tension roll separation and the commercial machines available for this purpose are discussed. The shortcomings of these machines are indicated and a machine that overcomes some of these undesirable character- istics is described. A procedure for evaluating laboratory high tension roll separation is described. The use of this evaluation procedure in conjunction with the laboratory separation is described with examples taken from the Dunwich and Hexham processing plants of Associated Minerals Consolidated Limited. Evidence that laboratory testwork results may be directly transposed to operating plants is given. A discussion of the effects of variables in high tension roll separation of mineral sand concentrates concludes the paper, and uses in support results obtained in the metallurgical laboratories of Associated Minerals Consolidated Limited, Southport, Queensland.

Jan 1, 1972

By Chander S

Properties of surface films on chalcopyrite and pyrite differ due to variations in the mechanism of oxidation of the two minerals. In the case of chalcopyrite the first step in the oxidation is the release of iron as ferric ions, which hydrolyse depending upon conditions prevalent in solution. The iron oxide/hydroxide layer formed by hydrolysis of ferric ions is quite porous and easily detachable from the surface of chalcopyrite. When the surface oxide layer is detached a sulphur-rich layer is exposed making chalcopyrite hydrophobic. The thickness and properties of the sulphur-rich layer determine its flotation response, both in the absence and presence of collectors. In the case of pyrite, on the other hand, iron is released as ferrous ions which require much higher pHs to hydrolyse. These ions remain adsorbed on the surface of pyrite making the surface hydrophilic. When the iron species are complexed with chelating agents such as ethylene diamine tetra acetic acid, pyrite was hydrophobic. Siderite forms in the presence of carbonate ions, which might be present in several flotation systems. Siderite nucleated on isolated sites at the surface. The presence of such a precipitate is likely to influence the interaction of pyrite with various reagents thereby altering its flotation behavior. To determine the mechanism of oxidation, kinetics of oxidation of chalcopyrite and pyrite was studied using several electrochemical techniques, namely, cyclic voltammetry, polarisation and impedance spectroscopy. Floatability of the minerals was investigated by measurement of contact angles on mineral electrodes and by Halimond tube flotation. Impedance spectroscopy was especially useful for estimating various properties of surface film for both the minerals. Properties such as charge transfer resistance, porosity, and capacitances of the surface films on the two minerals are compared under several conditions of oxidation. These properties were found to be a strong function of the rate and the extent of oxidation.

Jan 1, 1993

By Restarick C. J & Stewart P S B, Kelsall D. P

Over a four-hour period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had sane reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one third of the lead losses in the final tails.

Jan 1, 1980

By D T. Feinstein, M B. Gotkowitz

In Wisconsin, state laws and regulations governing metallic mine permitting stipulate that protection of groundwater quality be assured indefinitely through all phases of the mining project, including development, active mining, reclamation, and long-term closure. By rule, the Wisconsin Department of Natural Resources (WDNR) requires that permit applicants use a numerical model to assist in the assessment of compliance with this requirement for all proposed mine-waste facilities. As a part of the compliance assessment, model calculations are used to predict groundwater solute concentrations through time at designated boundaries for comparison to current groundwater quality standards. In practice, this modelling requirement has involved the application of numerical solute-transport models. Our review of a solute-transport model submitted by the developers of a proposed mine near Crandon, Wisconsin, provides us with an opportunity to assess the usefulness of transport modelling as a permitting requirement. Recent evaluations of solute-transport models by other workers suggest limitations in predictive accuracy. Our review of the model submitted for this project also identified important limitations due primarily to uncertainty in calibration of model parameters at the undeveloped site. The utility of any model to predict project compliance or non-compliance with numerical standards is limited by the range of uncertainty of key model parameters, such as dispersivity and porosity. Uncertainty in the future behaviour of the solute source(s) also reduces the predictive power. Moreover, the site characterisation provided by the model may have limited power to describe the site condition post-development. Although these inherent shortcomings accompany the use of solute transport models at undeveloped sites, the requirement for model development and the ensuing technical review has substantially assisted in our evaluation of site conditions and project design. Through this process we have identified elements of the waste facility design that are crucial to the environmental viability of the project, resulting in modifications to original project proposals. While results from this model review will be used to evaluate compliance, additional benefits come from the identification of critical design features that enhance groundwater protection.

Jan 1, 2003

Geological. engineering is a field of engineering practice concerned with design and construction of excavations and structures in soil and rock masses. The role of geological engineering in mining practice is defined in this paper, and the scope of the various disciplines in engineering science and geoscience which support geo-engineering research is discussed. The current national research capacity in geo-engineering is considered, and current and future needs for geo-engineering research for mining practice are proposed. Education programmes to sustain the proposed level of research and its industrial implementation are Suggested.

Jan 1, 1986

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986