Search Documents

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

By J M TORLACH

Learning is an iterative process, and we might reasonably expect that after more than a century of mining during an era of sustained technological development, (following a millenium or two of unrelieved hard physical graft), that the more obvious physical hazards could by now be competently managed. It is perhaps a reflection on the perversity of human nature that we have not fully learned our lessons in this exacting environment, and that worse, we have still too often failed to profit by the experience of those lessons. The more obvious underlying factors which impact on this situation are examined briefly, as a prelude to consideration of some outstanding examples of recurrent problems experienced in recent years. Reasons for the continued existence of sub-standard practices are outlined, with a focus on the human element, and finally proposals for appropriate remedial strategies are summarised. This paper therefore seeks to examine and discuss some of our deficiences and to suggest some directions for the way ahead.

Jan 1, 1992

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

By R Steinhaus, D M. Frantois-Bongarton, P W. Cleary, G K. Robinson, M D. Sinnott

Multotec Process Equipment and Dominique Frantois-Bongarton have a patent for a mineral sampling device, which they call a æTrue-Belt SamplerÆ. This uses a plough, which is rotated about an axis parallel to a conveyor belt to throw material off the belt. A fixed sample cutter takes a sample from the material thrown off the belt.Discrete element modelling has been used to consider a range of plough designs, plough speeds, positions for the cutter relative to the plough, cutter apertures, cutter designs and frictional properties, prior to the building of a physical prototype. This modelling work will be discussed, both as an illustration of the role of modelling in the development of new materials-handling devices and in order to explain the likely strengths and weaknesses of this new type of sampling device.CITATION:Robinson, G K, Sinnott, M D, Cleary, P W, Steinhaus, R and Frantois-Bongarton, D M, 2012. Modelling of a ætrue-belt samplerÆ - A new device for sampling from a conveyor belt, in Proceedings Sampling 2012 , pp 33-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By V Rimal, d M. Tangstad

Multiphase slags form the basis of the reduction pathway for manganese ferroalloy production. The present work aims to understand the flow of slag through the coke bed based on experimentation in controlled conditions. Synthetic slags of different basicities were evaluated for their phase composition, viscosity, and flow. The two-phase slag will have two zones: a liquid slag zone and a multiphase zone. The multiphase zone will consist mostly of a solid phase with some liquid slag between the solid particles. The multiphase part will hence have a high viscosity. The liquid zone will flow into the coke bed while the multiphase area will stay. With increasing reduction, the multiphase area will decrease in size until the solid phase is gone and the whole slag will flow into the coke bed. The effective viscosity of slag will decrease with the lowering of the solid oxide phase. The results from flow experiments confirmed that the segregation of phases occurs when slag flows through the coke bed. It is observed that the flow is dependent both on the size of the void and the viscosity of slag.

Aug 21, 2024

The brown coal resources of the Latrobe Valley, which include over thirty thousand million tons of coal suitable for open cutting, provide the main source of fuel for the power generation for the State of Victoria. They also provide the basis for the development of a supply of cheap hard fuel for industrial and domestic use, and for the development of the Lurgi process for manufacture of town gas for most of the State. The production of hard char for metallurgical processes and liquid hydro carbons will each, no doubt, play its part in the industrial growth that will be based on these resources.The State Electricity Commission of Victoria, which has been allocated the task of developing these deposits since the early 1920's, is faced with problems of economic selection of deposits for development, and excavation and transport of huge tonnages of coal and overburden-in this year, 19'59, about 12,000',000 tons of brown coal will be won, and over 7,000,000' cu. yd. of overburden will be removed in the four open cuts operated by the Commission; by 1967, eight years from now, the demand will have doubled.This paper deals with the nature and importance of various factors effecting the planning of the development of these resources. It is in essence an introduction to the papers by C. S. Gloe, H. C. G. Rodgers and J. M. Alexander, also being -presented at the Institute conference in Victoria in August, 1959.INTRODUCTIONIt is the intention in this paper to define the factors that come under consideration in the planning and development of the brown coal fields in the Latrobe Valley, whose exploitation by the State Electricity Commission of Victoria was initiated almost 40 years ago. It is proposed to enumerate, and in sorile cases evaluate, the physical and economic criteria that play their part in determining planning for the future.

Jan 1, 1960

By T Baumgartl, B Richards

Covers on waste rock and tailings remain the primary choice for closure planning where the purpose is to create an environment where water ingress into reactive material can be controlled and/or prevented. In semi-arid and arid environments, dry cover systems are the preferred option with the design intention to absorb rainfall and to prevent deep drainage. Although the average amount of rain typical for semi-arid environments is relatively low and evaporative demand is high, the seasonal and annual distribution may vary greatly. Rocky substrates are often the only choice for the construction of covers due to economic constraints or availability of suitable materials. While the water holding capacity may be suitable for the application of a dry cover design in arid and semi-arid climates, some of these covers bear the risk of preferential water flow when rain events are intensive or occurring at high frequency. The objective of this presentation is to demonstrate the occurrence of preferential flow through rock containing dry cover systems. A regional classification for the applicability of dry covers is attempted to delineate those regions of Australia where the characteristic of the rainfall pattern increases the risk of failure for dry cover designs. CITATION:Baumgartl, T and Richards, B, 2016. Rainfall patterns rather than climate classification control cover design for closure, in Proceedings Life-of-Mine 2016 Conference, pp 89–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Traditionally trucks have dominated haulage in open pit mines. Only recently have conveyors begun to be used in the long haul and high lift duties of surface mines. Steep angle conveyors are proven versatile systems for elevating or lowering materials continuously at steep angles to 90¦. This paper describes the design of a bucket-type steep angle conveyor that was developed as a joint research project between the Western Australian School of Mines and the Maanshan Institute of Mining Research in China. The steep angle conveyor can be used as a viable option for transporting blocky ore from open pit mines. A pilot conveyor was constructed and tested to determine its technical and operational feasibility. Furthermore, a computer model based on Matlab mathematical modelling software was developed to simulate the performance of the pilot conveyor. The model enabled to determine the design parameters of industry-scale conveyors to yield satisfactory performance. These conveyors become very cost-effective for those mines having large mine lives and depths greater than about 500 metres.

Jan 1, 2003

By Sehic O. A

Geology can be the root of evil or a source of bliss; there is a choice; to ignore geology is at a mine's peril.Risk can be minimised and profitability maximised by the application of a detailed understanding of geology, alteration, structure, mineralogy, chemistry, fabric and texture.Geology is dynamic, not static.The impact of geology is pervasive.The integration of ore quality control with grade control is one strategy for improving the utilisation of both the mineable reserves and existing plant and equipment. Grade maintenance is but one constraint on the problem of how best to blend the ore. Other ore characteristics such as mineralogy, hardness for grinding, and pulp fluidity or density for slurry size classification can be included to explore alternative blending Strategies.

Jan 1, 1993

By D K. Miller, L W. Armstrong

In April 2006, Orica Quarry Services undertook an investigation to determine the likely vibration and frequency response of three water storage tanks to quarry blasting, immediately adjacent to the tanks. Of the three tanks that were studied, two are relatively tall with a æwineglassÆ shape; one is constructed of steel (4 ML storage capacity) while the other is constructed of concrete (2 ML storage capacity). The third is a ground-embedded concrete tank that is relatively squat and broad in shape (38 ML storage capacity). A vibration limit of 25 mm/s and an acceleration limit of 0.16 g were imposed on the tanks. However, this report shows that this acceleration limit, whilst having relevance to low frequency earthquake motions, is quite inappropriate for the high frequency blast vibrations that are typical in a quarry blasting environment. The investigation involved firing 11 single blastholes of known charge weights and distances from the tanks, and measuring the tank vibration response using blast monitors placed on and around each tank. Analysis of the data collected from the cement tanks showed resonant responses over a broad range of frequencies, with dominant and lesser responses in vertical and lateral motion recorded at 9.8 Hz, 12 Hz, 16.8 Hz, 17 Hz, 31.3 Hz and 38.1 Hz. Unfortunately, most of the data collected on the steel tank was corrupted by noise due to electrical sources and/or mechanical sources such as the water agitator inside the tank. Advanced Monte Carlo vibration models were then constructed using the single blasthole information. Knowing the resonant frequencies enabled the modelling of electronic delay sequences for the reduction of resonant vibrations. Ultimately programmable and accurate electronic delay detonators were deemed essential to allow blasting in relatively close proximity to the tanks while avoiding resonant frequencies. Three blast designs were modelled, ranging in maximum instantaneous charge (MIC) from 4 kg to 22 kg, and 60 holes to 160 holes. The modelling showed that two of the designs (using small charge weights) could be used no closer than 71 m from the storage tanks. This is based on a 90 per cent confidence level of achieving vibration levels within the 0.16 g acceleration limit, even though the velocity levels predicted to be generated at this distance were significantly less than the 25 mm/s limit. The third design incorporated larger charge weights and could be used for blasting at distances no closer than 220 m from the tanks. The present work, conducted in an operating quarry, demonstrates the usefulness of Monte Carlo waveform superposition techniques for the control and reduction of ground vibration (either velocity or acceleration) under restrictive environmental constraints. However, a discussion is also presented to demonstrate that it is somewhat restrictive to impose an acceleration limit based on the motion produced by low frequency earthquakes rather than the motion produced by high frequency blast vibrations.

Jan 1, 2007

By Nilsson C

Man has always been and will always be part of his environment, in ,a good, bad or indifferent manner. Until quite recently, this environment has been the atmospheric boundary layer above the land masses, and to a limited extent the air-sea interface of the oceans. Since the days when he lived in caves, he has built up a wealth of observations on these two environments,-with ever-increasing scientific precision which unfortunately until quite recently was completely insufficient for modern capabilities of data analysis. Consequently, in a sense, he has left in his wake thousands of years of missed, opportunities for making exact observations and increasing his understanding. The data of the past are lost and he has to be satisfied with what he can assemble from now on when his environ- ment, largely as a result of his actions, is exhibiting more and more rapid variations in time; in other words, time series of observations of phenomena are required, the length of which is critical for most purposes of analysis.

Jan 1, 1970

The increasing global demand for rough materials forces almost every mine to look at the mechanisation in their processes. This will not onlyimprove performance but with safety issues becoming more and more prevalent, the need for the introduction of mechanisation technologies to mining applications is essential. Ongoing developments are occurring in almost every field, ranging from basic developments to specialised mining. Mechanical tunnelling and shaft sinking have set the standards regarding safety, profitability and environmental protection. Different machine types and working principles have been developed to suit the geological and hydrological requirements of tunnelling projects worldwide. Continuous activity in research and development leads to constant optimisation of tunnelling performance.

Jan 1, 2008

By T Laurencont, C Unger

The Mount Morgan minesite, located approximately 40 km SW of Rockhampton in Central Queensland, comprises 270 ha of unrehabilitated land which is the currently the major source of acid mine drainage run-off and seepage to the adjacent Dee River. Additionally, the minesite hosts an Open Cut Pit which contains 9000 ML of acidic and metal-rich water. In the absence of active management of water in the pit, there is a 50 per cent probability of an uncontrolled spill occurring in future years. The development of a contingency plan for management of overflow from the pit in the short term, has incorporated findings from numerous studies relevant to the Open Cut Pit including, but not limited to, water balance, contaminant source identification, toxicity testing, water quality profiling and limnological modelling, and estimates of probability of overflow. Extensive stakeholder consultation and peer review were also undertaken during the formulation of the contingency plan. The medium-term goal of lowering the water level in the pit to reduce the current high probability (50 per cent) of uncontrolled overflow to acceptable levels of risk is proposed to be achieved by a campaign of chemical water treatment. The treated water will be discharged to the Dee River, and sludge returned to the pit. The methodologies used for the selection and development of the water treatment process, that is proposed to involve treatment with lime, are described. Water treatment is the short- to medium-term component of a long range rehabilitation plan for achieving a negative pit water balance, and sustainable management of acidic water across the whole site. Achieving this ultimate goal will involve: reducing the inputs of water to the Open Cut Pit such that the annual water balance is zero or net negative, thus removing the need for water treatment in perpetuity; maximising, by surface rehabilitation works, the quality of run-off reporting to the Dee River; and minimising the volume of acidic seepage reporting to the seepage interception system. Possible strategies for achieving this long range goal consistent with overall site rehabilitation objectives are currently being developed and costed.

Jan 1, 2003

By Trueman R

If continuous mining systems are to be successfully applied in metalliferous mines then reliable models will be needed to predict rock cutting machine advance and tool wear rates for effective machine selection before mining commences. Many of the predictive models developed to assess cuttability in situ are over-simplistic. As a result they tend to be both site and/or machine specific. Nevertheless very detailed models have been developed for full face machines which are capable of accurate cuttability predictions in a variety of rock mass conditions and for a variety of machine and tool configurations. However, models to predict productivity and tool consumption for partial face machines are not as well advanced. There is a need to develop reliable models for partial face machines such as Roadheaders, the Robbins Mobile Miner and the HDRK-Wirth CMM, as these types of machine are likely to predominate in a mining environment. The paper outlines the current state-of-the-art for predicting cutting machine performance and the work being carried out within the Centre for Mining Technology and Equipment (CMTE), in collaboration with the Australian mining industry, to advance our capability in this area.

Jan 1, 1995

By Jena, Anand S, Das R. P

Leaching studies were carried out on Indian Ocean manganese nodules using sulphuric acid as the lixiviant. By leaching the nodules with 8 per cent sulphuric acid for 12h at 100°C, copper and nickel could be completely extracted along with 50 per cent cobalt and 6.2 per cent manganese.94.2 per cent of the iron was also dissolved. To increase manganese and cobalt extraction, charcoal was used as a reductant. The role of charcoal was to reduce the manganese dioxide and render it soluble as manganese sulphate as well as to facilitate solution of the cobalt minerals associated with the manganese dioxide. Various leaching parameters were studied including acid concentration, amount of reductant, leach time, pulp density and leach temperature. It was found that by leaching the nodules with 10 per cent sulphuric acid at 100°C for 4h using 5 wt/wt per cent charcoal (0.05g of charcoal per g of nodule) almost complete extraction of copper, nickel, cobalt and manganese could be achieved. However, under these conditions all the iron present in the nodules was also leached.

Jan 1, 1989

A survey of leaching systems for the dissolution of gold has been undertaken and their advantages and disadvantages evaluated both from their effectiveness at leaching and their compatibility with carbon- in-pulp (CIP) and resin-in-pulp recovery. In the near future it is almost certain that cyanidation in some form will remain the leaching system of.choice although economic and environmental pressures could see the introduction of other leaching systems particularly for treating refractory gold ores. The most likely alternative leaching systems appear to be acid chlorine, acid thiourea and ammoniacal thiosulphate. INTRODUCTION High grade reserves of readily recoverable gold ores are gradually being depleted which, inevitably, must create a greater awareness amongst gold producers, of the efficiency and, in some cases, the suitability of present day metallurgical processes for treating low grade, complex and refractory deposits. One of the key steps in the extraction of gold is the dissolution of the metal using chemical reagents which, ideally, should be cheap or recyclable, selective, non-toxic and compatible with down-stream recovery processes. In practice, meeting all these critera is difficult - if not impossible - particularly in view of the stringent environmental impact requirements which must be met Nowadays.

Jan 1, 1982

By Tumilty JA, Douglas WD

With a view to characterising activated carbons with respect to their ability to adsorb gold from cyanide solutions, an attempt was made to establish correlations between the equilibrium capacity constant of the activated carbon for gold (k value) and five other parameters. These parameters were percentage ash content, iodine number, methylene blue value, surface area, and pH respectively. Twenty four different proprietary brand activated carbon products were examined, the correlations being established by means of linear regression analysis. It was shown that a significant correlation only existed between k and pH value. This was interpreted in terms of the presence of oxide complexes on the activated carbon surface. Further test specifications as developed at the Anglo American Research Laboratories are also outlined with a view to the selection of activated carbons suitable for use in' a carbon-in-pulp operation. Methods for assessing both the capacity and the kinetic response of carbons for gold adsorption are presented, while the measurement of attrition resistance, particle size distribution and moisture and solubles content is also outlined. The measurement of the capacity constant for gold adsorption together with attrition resistance are considered to be necessary in the initial selection of a suitable carbon.

Jan 1, 1982

By T Laurencont

The Queensland Department of Natural Resources and Mines (NR&M) accepted the environmental liability for the Mount Morgan minesite in 1991. This gold and copper mine located 38 km southwest of Rockhampton had been in operation for more than 100 years. Mining leases are still active while the feasibility of a reprocessing operation is carried out. From 1993, NR&M have operated a seepage interception pumpback system which has reduced the chronic load of acid rock drainage (ARD) to the adjacent Dee River, a tributary of the Fitzroy River system. In early-2000, it was recognised that a ten-year plan for rehabilitation of the mine, along with significant funding would be required if a long-term sustainable rehabilitation strategy was to be implemented at this minesite, ultimately making the seepage interception system redundant. A rehabilitation planning workshop coordinated by NR&M was held in May 2000. This workshop brought to the mine a range of technical expertise and key stakeholder groups. This workshop provided a technical forum for review of studies undertaken and to identify priority projects, which needed to be undertaken in the future to more clearly define contaminant sources on the mine site and to prioritise the rehabilitation program. Stakeholder consultation enabled the project team to be clear on community and other government (eg Environmental Protection Agency) expectations. It is clear that the future of the economically depressed community of Mount Morgan will be reliant on the careful management of the significant heritage values at the minesite for tourism, education and research. In the first year (2000), priority studies were initiated, which included whole of site studies on water balance, contaminant sources and a review of occupational health and safety and environment of the minesite and conservation and heritage scoping. Baseline vegetation and soil materials surveys were also initiated. The outcomes of these studies helped to shape the work program for the following year, while providing a basis for an additional funding application, which was granted. The second year of studies focused on building upon the existing baseline studies completed. In addition, studies focussed on addressing the priority issue of contingency planning for overflow from the open cut pit in accordance with best practice management of release water and river monitoring strategies were completed. Completion of these projects over the next six months will enable the optimal rehabilitation strategy to be defined in 2003. This optimal strategy may require the use of a water treatment plant for part of the ten-year program to provide space in the open cut pit for the deposition of ARD contaminant sources (eg waste dumps, tailings). It is envisaged that some sources will be rehabilitated insitu while others will be relocated to the open cut pit. Implementation of this strategy will be dependent on subsequent funding.

Jan 1, 2003

By Svenson D

For fully effective information to be obtained from exploratory drilling for coal, drilling programs should be planned systemati- cally in successive stages, on the basis of existing geological criteria and information collated during each stage. In this way, drilling can be executed with optimum economy, aided by auxiliary geophysical techniques wherever these may be appropriate. The object- ives of the programs must ultimately include an adequate assessment of mining conditions as well as thorough evaluation of coal quality. The first of these objectives is not always appreciated by both geologists and mining engineers engaged in supervising drilling pro- grams, often resulting in the need for more additional drilling and more expense than would otherwise be required. To achieve all of these objectives as effectively as possible, the drilling should be supervised by well qualified personnel experienced in working in a multi- dicipline, professional mining, geological and engineering team.

Jan 1, 1977