Search Documents

By Lyman G. J

Magnetic separator operation in the recovery of magnetite in heavy medium circuits was studied by conducting a series of tests on a full size wet drum magnetic separator.The significant operational variables were found to be feed pan clearance, squeeze pan clearance, dry magnetite feed rate and separator drum speed. With feed and squeeze pan clearances optimized for typical primary separator operation, magnetite loss and concentrate specific gravity were found to be related in a regular manner to dry magnetite feed rate at any drum speed.A two component model of magnetite loss is proposed, relating total magnetite loss to losses in the feed pan and squeeze pan zones. The experimental curves relating magnetite loss to dry magnetite feed rate at the various drum speeds are interpreted in terms of the two component model.The magnetite particle size distribution in the separator was also examined. The tailings magnetite was found to be finer than the feed magnetite only when the dry magnetite feed rate was low, or immediately following the introduction of a new charge of magnetite when the separator was fed at an intermediate dry magnetite feed rate.

Jan 1, 1983

Factual data about the sedimentation in the Newcastle Coal Measures are presented. Data concerning the total coal measure sequence (isopachs, sand/shale ratio, and total coal thickness variation), data about three coal seams (Borehole, Dudley, and Victoria Tunnel) and data about interseam conglomerate units are discussed.From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature, was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin.The northern and north-eastern edge, which was unstable, supplied most of the coarse detritus (including the conglomerates) to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern- each show development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure.Evidence of ill situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.The unusual character of this coal basin, in particular the very coarse units, is stressed, despite the presence of many "normal "coal basin features.

Jan 1, 1970

After a snap-shot survey of water quality of streams draining various coal measures carried out in 2000 - 2001, West Coast Regional Council expanded its monitoring programme to better establish the condition of streams draining coal mining areas and to characterise the variability of water quality with respect to stream flow. Samples were collected for water quality indicators such as pH, sulphate, turbidity, conductivity, temperature and dissolved oxygen as well as macro-invertebrates, fish and assessments of stream habitat. Water quality sampling was carried out at 27 sites on 21 streams located from Page Stream near Seddonville in the north, to Seven Mile Creek near Dunollie in the South, and to Garvey Creek east of Reefton. There was relatively low variability of pH, conductivity and sulphate concentrations at most of the sites sampled. Conductivity and sulphate concentrations reduced with increasing flow and pH generally increased. Significant effects on macro-invertebrate and fish populations were identified at several of the sites where water quality sampling was undertaken. Of the water quality parameters tested, macro-invertebrates were mostly affected by pH. Although not sampled directly (conductivity was used as a surrogate) heavy metal concentration may explain some of the variation in macro-invertebrate communities. Three creeks affected by mine drainage were sampled for fish and no fish were present. Fish appear to be more sensitive to acid rock drainage that invertebrates. Using data from this survey and other studies conducted in the region, the total length of stream that is actually or highly likely to be adversely affected by acid rock drainage was estimated at 125 km. This figure is useful as a gauge as to the magnitude of the issue in this region and for setting of priorities for remediation. However, as it is only an estimate based on limited sampling sites, it should be used with caution.

Jan 1, 2003

Gold in the stibnite veins of Costerfield, Victoria, was described in 1922 1, prior to any mineragraphic examination, as (a) free yellow gold (b) free rusty gold and (c) combined gold. The free yellow gold occurs in quartz and will amalgamate with mercury. The free gold of dull, rusty or copper-red colour occurs in massive stibnite and has been stated to resist amalgamation with mercury. The dull colour is only skin deep and the colour is bright when the rusty gold is scratched. The appearance of the rusty gold is spongy or cellular and it generally occurs near small cavities in the stibnite. The suggestion that the cellular character indicated the removal of a certain amount of stibnite leaving a residue of se.condary gold cannot be sustained.It now appears probable that the rusty gold is formed by the primary dissociation of a gold antimonide and is distinct in origin from the normal yellow gold which is deposited with quartz or stibnite from auriferous mineral solutions.The combined gold referred to in the earlier paper was the gold contained in the stibnite as revealed by assay. Such gold was at first thought to be either dissolved in the stibnite or else present as free interstitial particles too minute for observation in transmitted light in thin sections.Subsequent examination of numerous polished,surfaces disclosed the small particles of gold occurring in the grain boundaries in aggregates of fine grained stibnite 2. The assumption that all the gold in the stibnite, as revealed by assay, occurred in this way is now known to be incorrect, because limited amounts of a gold antimonide have been found in the veins.

Jan 1, 1952

Coal cleat and faulting influence failure, gas release, and choice of preferred mining directions, locations, and sequences. Unfortunately soil and younger rock cover restrict direct mapping of these structures ahead of mining operations. Aerial photographs of cover contain indirect indications of concealed structures in arrays of linear photostructures. These arrays are commonly too complex for interpretation by simple visual inspection.Analytical techniques applicable to complex arrays are illustrated for a covered part of the Galilee Coal Basin, Queensland. These techniques are: optical determination of sets in arrays of photostructures; correlation of these sets with sub-surface structures; filtering of m-rays for particular sets; detection of anomalies associated with concealed structures in the density distributions of particular sets; fitting filtered arrays to trajectories; correlation of trajectories with the regional directional variations of concealed structures; contouring of ratios of sets to discriminate anomalies associated with concealed fractures and variations in the total and bed thicknesses of cover; kinematic and dynamic inference on the basis of fracture-trace angular and spatial relationships.

Jan 1, 1979

Six simulations by the Mpnte Carlo method employing both classical and geostatistical techniques are presented for the determination of the probability distribution of the in situ value of a coal seam. To avoid the problem of qualitative estimation of parameter variability in the calculation of an arbitrary seam value, only data values from borehole information were used to quantify the variation in four coai seam parameters.The method which is suggested as being the most appropriate is a particular geostatistical approach that employs the best linear unbiased estimate and the error of estimation for a number of two dimensional blocks. The results indicate that the variance of the coal seam unit value may be much higher than that indicated by the classical approach because of the spatial variability that is properly incorporated in the geostatistical approach.The model used in the Monte Carlo simulation to determine the economic value of a coal seam can be extended to incorporate all those parameters which are necessary for a true estimation of the probability distribution of the coal seam value. A time value concept for discounting can also be incorporated to optimize the economic return of a coal mining project.

Jan 1, 1983

On the more important mines it is almost essential to have a general plan of the surface. A special feature of this plan should be the indication thereon of a suitable arrangement of contour lines, either wholly over the surface of the property or at parts where may seem most useful. The importance of having these contours marked on the plan will be best appreciated by the engineer, in selecting the best available site for a proposed new plant, in locating a tramway, in connecting the surface with the underground workings to the best advantage, or in solving many similar problems that come within his province. The closer the contours are together vertically the better, the limitation being the trouble and expense of getting them on to the plan. They may range from five to fifty feet apart but a distance of ten feet will be found, in most cases, to be the most useful.In deciding the datum level from which these contours are to be measured, it is best to depart from the ordinary sea level datum, and use instead the highest available point on the property. This datum will be called zero and all levels will be reckoned so many feet below it; thus by a contour marked 160 on the plan, it will be understood that the level of the plane of the contour is 160 feet below the highest available point on the property. This system of measuring levels downward is readily suggested from measuring the depths of shafts from the brace or of excavations from the original surface.

By Lancucki C. J, Nickson N. M

X-ray diffraction and differential thermal methods were used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis was made of the mineralogy and particle size distribution of eighteen samples from beds in two pits in the Recent sediments in the Adelaide plains, of six white clays developed from the weathering of the Adelaide series of sediments, and of four Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products in the Adelaide area are manufactured from mixtures of these clays, so the mineralogy and particle size distribution was determined of eighteen clay mixtures used to make red bricks, cream bricks, facing bricks, pipes and tiles.Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.INTRODUCTIONIn this investigation an account is given of the clay mineralogy and particle size distribution of some ceramic clays from the Adelaide area. The clays are used in the manufacture of structura,l clay products and the results to 'be described are part of an overall 'plan of study covering the heavy industrial clays and shales of Australia. Previous work has been published (Cole and Carthew, 1953; Ferguson, 1954; Ferguson and Hosking, 1955; Cole and Nielsen, 1958/59).In this work no attempt has been made to examine clays from all pits engaged in supplying materials for the structural clay industry. However, in 1954 the senior author collected detailed samples from two pits working in Recent alluvial clays in the Allenby·Gardens and Beverley areas near...

Jan 1, 1963

In undertaking to write a few notes on practical mining in Bendigo, the great quartz mining centre of Victoria, which just now is celebrating its fiftieth anniversary of gold mining, satisfaction must be expressed which is, no doubt, shared by all mining men and inyestors, that Bendigo has not lagged behind other Australian mining districts in the evolution of mining from its crude state, subsequent to the discovery of gold in 185 to its present more perfect state; and though it may be said that it has not yet reached the high pinnacle of perfection towards which advanced science and change of conditions may yet lead it in the course of future progress, yet, what has already been done in this respect, the adoption of the most approved methods appliances and modern machinery, tending towards greater and still greater efficiency, facility, and economy in our mining industry, must be accepted as a guarantee that in tne future as well as in the past, progress in our means of developing our mining resources will ever remain our watchword, by means of which future difficulties will be overcome as well as they have been removed in the past.The adoption of this principal, combined with a study of rigid economy, has raised gold mining here, as well as in other places, from a state of speculation, and sometimes wild speculation, to the status of a solid, stable industry, the strong supportand backbone of the country in which it flourishes. Two of the principal factors which have been to a great extent instrumental in bringing about this satisfactory state, must be specially mentioned.

Jan 1, 1902

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By Garnsey R. G T, Wenk G. J, Toop A, Sowerby B. D

A bulk mineral analyser (BMA) suitable for the determination of Cu or Ni in bulk ore samples has been developed at the Lucas Heights Research Laboratories. This analyser, which uses the nuclear resonance scattering technique, is highly specific to the wanted element. The technique has previously been extensively field tested for copper at Mount Isa, Queensland.The present paper discusses the field trial in 1982 of a commercial prototype BMA for nickel. The trial was undertaken at the lateritic nickel mine at Greenvale, Queensland. The BMA and its shielding, together with a laboratory spectrum analyser, were sited in the sample shed adjacent to the workings. Two hundred and thirty-eight ore samples taken directly from the mine blastholes were assayed by the BMA. The average mass of sample was 12 kg, metal contents varied from 0.2 to 3.5 wt/per cent Ni and 4 to 43 wt/per cent Fe and free moisture varied from 11 to 55 wt/per cent. A measurement took 10 min to complete, although this time could have been reduced at the higher nickel grades. The r.m.s. deviation between BMA and chemical assays was 0.09 wt/per cent nickel. Iron and bulk density were also determined by the BMA, r.m.s. deviations being 1.7 wt/per cent and 0.03 g/cmJ respectively. Similar results could be expected from a BMA in routine industrial use at other nickel mines.

Jan 1, 1983

By K Nilsson, D Connelly

Troy Resources acquired the Karouni Gold Project in Guyana, South America in 2014 and immediately proceeded to a Pre-Feasibility Study and project implementation. The study considered two open pit mines feeding a conventional carbon in leach (CIL) gold plant with a capacity of 1Mtpa. The study assumed a total of 2.61 million tonnes of ore with an average grade of 3.84 g/t gold with a recovered gold production of 303,526 ounces over a three year mine life.The project development involved drilling metallurgical test holes, securing second-hand major pieces of equipment where suitable, and arranging shipping to Guyana. The remote location meant logistical considerations were paramount. The plant consists of conventional two-stage crushing with single stage ball milling and a gravity circuit. The tailings circuit includes DETOX.The extremely high rainfall presented challenges with water management and the necessity to dispose of clean water to the environment. The DETOX was also mandatory due to the highly sensitive environment and past history in the area. The criticality of this meant that in the design, any cyanide in the tailings would precipitate in a plant shutdown.Lessons were learned and the project has been both profitable and successful for Troy Resources in a new operating location. In addition, the project has created jobs, delivered royalties and brought new skills into an area where previously there was little current mining activity.CITATION:Nilsson, K and Connelly, D, 2015. Karouni Gold Project from drill core to commissioning, in Proceedings MetPlant 2015, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country's total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment.   Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry.   Equipment suppliers now offer maintenance services, production guarantees and flexible financing.  Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a 'package' approach to customer service.

Jan 1, 1997

By A Hanna

Quarries around Auckland have reached or are reaching the ends of their lives, which raises issues about rehabilitation. Significant volumes of 'cleanfill' are generated by the City, particularly during phases of urban renewal and development. Emplacement of the fill in quarries removes the problem of fill disposal and provides an opportunity for restoration of the quarry site.There is a compatibility between quarrying and cleanfilling because at quarries:Truck routes are already established Neighbours are accustomed to the effects and appropriate buffer distances have been established Bringing fill into a site attracts aggregate sales and is very efficient. Fill originates from construction sites and ad-hoc excavations and therefore it is not surprising that sampling has shown the quality to be variable. Both Winstone and the Auckland Regional Council have surveyed undisturbed soils in the region to attempt to determine natural background levels of common contaminant substances. Comparison of these levels with delivered fill shows that a high proportion of delivered materials can be regarded as mildly contaminated. Therefore the term 'cleanfill' is, in the Auckland region at least, a misnomer and the term 'managed fill' has been adopted.Historically and presently the only control on quality of 'cleanfill' has been some visual inspection. This leaves the fill operator open to potential liability for creating a contaminated site. Implementation of controls at WinstoneÆs operations has progressed slowly, over some ten years. This is mainly due to the perception that mobility of contaminants within and out of the landfill will be very limited because of the near-neutral pH and abundance of clay minerals in the fill. The methods of control and results of environmental risk assessments at WinstoneÆs Puketutu Island Quarry will be briefly described.

Jan 1, 2002

By Sofoulis J

In the Archaean of the Kalgoorlie-Norseman area, the layered rocks have been subdivided into two sequences, both containing basic igneous rocks and sediments. The lower sequence is distinguished by the presence of acid volcanic flows and large acid sills. The upper sequence is unconformable on the lower one.In some areas, clastic sediments become coarser and pass into conglomerates. Th:s passage is accompanied by thinning of the beds.These features and their distribution suggest a basin of subsidence flanked by areas of shore-line conditions.Repeated igneous activity, including vulcanism, has occurred along the flanks of this basin. These different igneous and sedimentary environments have played an important part in the primary distribution of metals.A chronology of all basic and acid igneous activity, as well as sedimentat:on, has been established for the Precambrian of this area.INTRODUCTIONThe subdivision of Archaean rocks into those of basic igneous or of sedimentary origin has formed the basis for the nomenclature appearing in past literature. These subdivisions were distinguished as greenstones (predominantly basic igneous rocks) and whitestones (predominantly sediments), and it was generally accepted that the greenstones were stratigraphically lower in the sequence than the whitestones.Recent studies show that, between Kalgoorlie and Norseman, basic igneous rocks interfinger with and pass laterally to sediments, and that basic volcanic rocks occur at different stratigraphic levels. Younger Precambrian. units are also...

Jan 1, 1965

By A H. Clemens, P Lindsay

Acid producing potential static tests have been undertaken on sample lithologies from New Zealand coal mines, to rank the lithogies into acid producing waste rock and stable non-acid producing waste rock. Results indicated that the main acid producing waste rock in the Waikato coal region are the marine Whaingaroa siltstone and the Glen Massey formations and the main alkaline producing lithologies were the Tauranga group volcanic-derived sediments (A & D) and the Mesozoic basement. Coal ash analysis of 28 samples from 28 mines have also been analysed for reactive S percentage and their base potential has been quantified by the chemical index of alteration (CIA). The results provide mine management in the Waikato Coal region with a classification of problematic and stable waste rock types. XRF and CIA values determined from wash drill cuttings would provide a method of determining waste rock volumes and magnitude of palaeo-weathering underground.

Jan 1, 1999

Several factors contributing to the loss of fibre during treatment are a function of the paragenesis of the veins. The occurrence, of magnetite from the cap rock within the veins prevents complete fiberization. There is a marked similarity between these veins and those in the Koegas-Westerberg area of South Africa.INTRODUCTIONAn investigation of the mineralogy of the Wittenoom Gorge crocidolite veins was undertaken in the latter part of 1962 at the request of the Colonial Sugar Refining Co. Ltd. It was anticipated that such a study might reveal the cause or causes of the lack of recovery of some asbestos during beneficiation. Some interesting features of the mineralogy and paragenesis of the crocidolite veins become apparent, but it is emphasized that the investigation is far from complete, as the study did not extend to the field occurrence.The samples examined were selected from the mill and from the untreated ore.GEOLOGICAL SETTINGWittenoom Gorge is situated on the Fortescue River in the Hammersley Ranges of Western Australia and is one of several gorges in these ranges, on the sides of which 'crocidoIite asbestos is known to occur. The Hammersley, Ranges consist essentially of a series of quartzites, shales, ferruginous quartzites and dolomites. These' rocks are part of the Nullagine Formation (Proterozoic) and are usually either horizontal or gently folded. In some 'areas small beds of riebeckite as well as crocidolite are known to occur interbedded in the sequence.Riebeckite is a monoclinic amphibole, the formula of which may be stated as Na2Fe2"Fe2" (OH) 2Si8O22, and crocidolite is a fibrous variety of this mineral. This formula...

Jan 1, 1963

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

Project developent proceeds by increasingly detailed studies addressing overall project returns through an analysis of the substance, risks and costs associated with the following elements: ò Reserves ò Mining ò Processing ò Infrastructure ò Environmental Impact ò Product Market Computer-based expertise has a potential to ò Capture perishable expertise, making this available for shared access and so reducing the cost of human experience ò Consolidate know-how for optimising process operations, bringing consistency of judgement and advice to decision- making by making the rules, facts and preferences explicit ò Allow assignment of the basis and authority of decisions, so experts can pass routine expertise down the line, freeing their time to generate more. ò Force a review of expertise when creating the knowledge base.

Jan 1, 1989

The author summarizes and extends the relevant results of papers previously published by various authors and presents these results in chart form. The charts are used to demonstrate the theory on a hypothetical mine.INTRODUCTIONRecently a series of articles have dealt with leakage in a mine ventilation system and the problem of its reduction.Theories were developed by Peascod and Keane (1955) for the combined effect of flow in the airways and leakage through the porous barrier between the intake and return of an ideal mine. Later Keane and Peascoa. (1956) extended these ideas to the use of an underground booster fan in increasing the face ventilation and showed how to determine the water gauge and location of the most efficient underground fan.These articles were based on the assumption that Atkin:son's formula:P = R Q2 (1)gave the relation between the pressure drop P lb'/sq. ft., the quantity, Q kilocusecs, flowing in the mine airways and the total resistance, R Atkinsons, to air flow offered by the mine roadway. An Atkinson is defined as a resistance such that 1 kilocusec of air flows due to a pressure drop of 1Ib.jsq. ft. However for conditions prevailing in most mines a more :appropriate relation is that postulated by Reynolds and others (Lamb, 1953) :P=R Qn (2)where n has some value slightly less than 2. It should be noted that Atkinsons may not be used as units when n is not equal to 2.

Jan 1, 1958