Search Documents

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By Unver B

Longwall advance mining is still the predaninant system of coal extraction in the U.K., contribiiting to sane 70 % of underground coal production. Gate roadways providing access to a longwall advancing coal face are maintained adjacent to a rib pillar under high strata abutment pressures and the caving rock mass. It is very difficult to realistically model such access roadways using mathematical or numerical techniques and hence, predict roadway closure. For the past 15 years, a research group in Nottingham University has been engaged in the study of longwall gate roadway stability using observation methods. Gate roadway deformations have been measured in 224 gate roadways and a comprehensive data base has been established. The paper describes the statistical analysis of this database and presents sane. predictive equations which will enable a forecast of the gate roadway closure to he made. Further field work to validate these equations. is described together with an error analysis. The results are very promising and indicate that it is possible to predict gate roadway closure in the U.K. within practical limits of Accuracy.

Jan 1, 1986

By R Lachenicht, J Player, A Thompson, E Villaescusa

Kanowna Belle Gold Mine is a deep, high-stress, sublevel open stoping mine located near Kalgoorlie. Seismic activity during the development cycle presented problems, including concerns regarding the exposure of personnel. A number of seismic management systems were developed and tested to monitor seismicity and control the risk. It was recognised that a dynamically capable reinforcement and support system was required to be installed as part of the development cycle to reduce the risk of exposure of the underground workforce to uncontrolled movement of rock. The performance of a new Garford Dynamically capable bolt was measured in tests performed by the Western Australian School of Mines (WASM) at their Kalgoorlie Dynamic Test Facility. Detailed descriptions of the facility and data processing were reported by Player, Villaescusa and Thompson (2004) and Thompson, Villaescusa and Player (2004). The development of the Garford Dynamic bolt is described and dynamic testing results are presented and evaluated. This bolt was implemented in the mining cycle following the testing program; the observed performance is described and assessed in this paper.  

Jan 1, 2008

By M Ahler

Future developments in the mining sector will be driven by the need to increase safety, ecological sustainability and efficiency. Autonomous systems represent a huge step towards achieving these goals. This paper describes the basic infrastructure of an autonomous system – essentially a network of distributed sensors. Although the sensors are distributed, the overarching communication network with its related middleware offers a transparent and uniform layer. This middleware acts as an abstraction layer which priorities information and provides information to other platforms on request. This permits higher-level autonomous functionality to utilise all information available in the system regardless of where data has been generated or via which physical communication link it has been processed.The Personnel Proximity Detection (PDD) system is described in detail as an example, with details not only of the system itself, but also of the essential full integration and how the abstraction layer allows this technology to be plugged in at any location of the network. The paper ends with a summary of the content and a conclusion.

Nov 22, 2011

In todayÆs evolving and globalised world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to æengageÆ communities and measure the success of these engagements without a clear understanding of æhowÆ to do this. This move, away from compliance, develops more of a focus on sustainability and æcommunityÆ social responsibility rather than corporate social responsibility. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of æengagingÆ communities in mining project design and development leads to sustainable development, a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be æengagedÆ in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this æengagementÆ and manage this risk will be discussed.

Jan 1, 2007

By J Cook

In this paper we present a case study of the challenges and opportunities associated with the development of cultural heritage management strategies at the Lihir gold mine in Papua New Guinea. We discuss the contextual drivers and constraints, and outline the ways in which Lihir Gold Limited is aiming to set new industry bench marks for the region through the development of values-based best practice cultural heritage management programs. This approach is largely based upon a compliance partnership with a local stakeholder group. We argue that such partnerships are a prudent means of mitigating company risk, while constituting a far more necessary tool for local people in the reconceptualisation and negotiation of the experiences of significant social change and modernisation experienced in the context of recent resource development.

Jan 1, 2009

By Box JC

A comprehensive computer simulation has been developed for heap and dump leaching processes. It deals with complex chemical interactions, involving several minerals and reagents, which vary with time and location in the dump. The simulation is generally applic- able to ores of various metals extracted by different reagents. It requires only mineral- ogical data obtainable from drill cores and chemical data obtainable from the literature; there is no curve-fitting with adjustable parameters. Applications in designing testwork programmes, evaluating operating options, transferring experience to new situations and reducing uncertainty in long-term forecasts are described. Specific examples are included illustrating the potential of the simulation.

Jan 1, 1983

By A Reschke

The Thiess John Holland Group is undertaking the design and construction of Brisbane’s Airport Link Project, the largest single investment in transportation infrastructure in Australian history. Twin Herrenknecht TBMs are being used to bore parallel road tunnels from Kalinga Part in Toombul through to Lutwyche, a distance of 2.45 km. At 12.48 m, these tunnel boring machines (TBM) are the largest diameter machines, outside of Japan, to incorporate annular two-component type grouting through the tailskins.Grout design, preparation and injection have been given particular attention in this project in order to push the boundaries of achievement. Laboratory testing was conducted on various mix designs to ensure the contract specifi cations for grout strength could be met. To study the mechanics of the grout injection process, Herrenknecht supplied a test rig which duplicates the grout injection systems on the TBMs. Multiple recipes were tested, carefully selected to balance the requirements of rapid strength development with high mobility (to completely fill the void between the segmental lining and the ground) and minimal bleed.Team Mixing Technologies, Canada, was selected as the grout plant provider based on the technical performance of their high shear colloidal mill mixers. Field results have shown that the colloidal mixer prepared grout gives almost double the strength of an identical grout prepared by a paddle mixer.

Mar 8, 2011

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By C J. Greet, S Jacques

In most instances, the application of high-chrome grinding media results in an increase in the recovery of the valuable mineral(s). The authors have published data from a number of plant-based case studies, which indicate that it is not unreasonable to expect a recovery increase in the vicinity of 1.5 to 2.0 per cent for a copper ore. It is of interest to understand where the increase in recovery is coming from. That is, is the additional copper recovery the result of improved fine particle flotation or is it due to an improvement across all size fractions?This paper aims to answer this question. Laboratory flotation tests were completed using forged steel and a high-chrome alloy on a volcanogenic massive sulfide copper ore. The unsized data indicated that the application of high-chrome grinding media to this ore resulted in an improvement in both copper recovery and copper concentrate grade. A detailed kinetic analysis of both the copper sulfide and gangue minerals was completed that clearly shows that the change to a more inert grinding media produced significant increases in the flotation rate constants (both fast and slow) across all size fractions. It is also possible to observe that the change in pulp chemistry has resulted in a decrease in the flotation kinetics of the -20 micron pyrite, while the coarse pyrite recoveries have increased, presumably because of an increase in the flotation of the chalcopyrite/pyrite composite particles.CITATION:Greet, C J, Jacques, S and Kinal, J, 2014. Recovery-by-size kinetic analysis to determine where metallurgical improvements occur when converting to high-chrome grinding media, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K Lee, L Mann, J Bygrave, G Sheldon

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By P Cleary, G K. Robinson, J Hilton, P Wilson

Concern has been expressed that Vezins can be biased when used for sampling fine materials if the cutter speed is as high as the 0.6 m/s which is often used. Using modelling techniques that consider airflow as well as particles, we have endeavoured to investigate sampling bias as a function of the size of fine particles, cutter aperture, cutter speed, shape of cutter blades, and the size of the gap between the inlet pipe and the cutter blades. Using crude estimates of the rate of airflow and a simple model of a single particle moving through air led to an approximate rule that bias will not occur due to mechanisms related to airflow for particles larger than about 200 microns; and bias will always occur for particles smaller than about 40 microns. For particles between these size limits, the extent of bias depends on particle density, cutter speed and cutter geometry as well as particle size.CITATION:Robinson, G K, Wilson, P, Hilton, J and Cleary, P, 2012. Avoiding bias when using vezins for sampling dusty materials, in Proceedings Sampling 2012 , pp 109-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By M Randall, P Ebzery, F Burns, C Aisthorpe, P Blanz

SAG Mill process control classically maintains the SAG mill volumetric filling within a set operating range. Typically a SAG mill weight measurement, by either bearing pressure transducers or load cells, is used as an inferred measurement of volumetric filling. To maintain volumetric filling within a set operating range the SAG weight setpoint use for process control requires regular review due to changes in SAG mill charge density (rock:ball ratio) and the wearing of mill liners. At Lihir Gold Mine in Papua New Guinea, the use of SAG mill weight for process control is additionally complicated by compromised load cells and drifting bearing pressure measurements. The need for an improved method of measuring and controlling volumetric filling led to the recent installation of the Outotec MillSense, a SAG mill toe angle instrument. This paper presents the integration of the toe angle control in to the Lihir SAG mill process control philosophy as replacement for the traditional mill weight control.CITATION:Burns, F, Aisthorpe, C, Blanz, P, Randall, M and Ebzery, P, 2018. Toe angle measurement for SAG mill control at Lihir gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 59–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Simmons, J Chan, A Li, Q Gu, D M. Brett

The paper presents an example of field density achievements using thin layer deposition and solar drying and compares this with compaction data from laboratory testing and field trials of mechanical densification processes.

Jul 1, 2021

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By J Col, D La Rosa, W Valery, A Jankovic

Metso Minerals Process Technology Asia-Pacific and South America (MMPT) has been working with operations around the world to increase their efficiency through æMine-to-MillÆ or Process Integration and Optimisation (PIO) projects. These projects have delivered significant improvements in mine efficiency, mill throughput and reduced operating costs at mines around the world. The MMPT methodology involves rock characterisation, site auditing, data collection, modelling/simulation and implementation of integrated operating and control strategies on site. This results in significant benefits to the operations û for example, 5 to 20 per cent increases in concentrator throughput have been measured. MMPTÆs rock characterisation utilises simple and inexpensive measurements that can be performed by trained site personnel. The advantage of these measurements is that a large amount of data can be collected in a very short timeframe, as the samples do not require shipping to an outside laboratory. Typically, a PIO project starts with a site visit to perform blasting and process audits, collect high quality data including measurements of run-of-mine fragmentation and survey data around all crushing and grinding circuits. These measurements are combined with rock characterisation and the definition of strength and structure domains to model the complete production chain. Site-specific models of the blast fragmentation, crushing, grinding and flotation processes can then be developed. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG or conventional grinding circuits. Process improvements can be higher mining productivity, higher mill throughput, decreased overall operating costs and higher flotation or leach recovery. This paper discusses a recent application of PIO conducted at a large open pit operation in South America and emphasises the potential that every operation has to ædo more with what they haveÆ.

Jan 1, 2007

By D Howe, J Conn, J G. McLellan, K Gates

The Red October Gold Mine, owned by Saracen Gold Mines Pty Ltd, is located approximately 80 km south of Laverton, Western Australia. It is considered to be of a similar nature to many of the Archaean granite-greenstone deposits in the Laverton Tectonic Zone, and presents as an intriguing and relatively young deposit in terms of developed structural and genetic models. Regional deformation events have been proposed for the area, and are relatively well accepted. The most important of these deformation events in the region were the D4b (WNW–ESE sinistral transpression) and D5 (ENE–WSW dextral transpression) which have been attributed to the main Au mineralising phases. At the local scale there appears to have been a rotation of the regional stress field to provide the optimum orientation of maximum principal stress for sinistral movement on the main shear zone.Fully coupled 3D finite element analysis (FEA) was used to simulate the geomechanical response of the system based on structural observations. The geomechanical modelling resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two main deformation events. The D4 simulation provided a good correlation with the known distribution of subsidiary structures on the main shear zone, and furthermore provided several geomechanical targets that suggested locations of additional subsidiary structures. The D5 simulation provided a great insight into the response of the main shear zone and known subsidiary structures also highlighting additional targets indicating potential for further mineralisation. These targets have since been followed up with a 732 m deep surface reverse circulation (RC) drill hole, resulting in the discovery of two high-grade shoots, with follow up testing currently planned for mid-2014.CITATION:McLellan, J G, Conn, J, Howe, D and Gates, K, 2014. Structural controls and strain partitioning in the Red October Gold Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Lott JB, Scuffham JB

Until very recently the application of solvent extraction to. the recovery of metals has been considered only for ithose operations where no other process was available. In general, .these operations, have involved metals such as 'f uranium or the rare earths, where the value of metal recovered has been very high. As a result, the tendency has been to consider solvent extraction as a very specialised, high cost technique with minimal application in the base metal industry. Since the mid-1960's this attitude has had to be changed drastically with the development of solvents specifically designed for the selective extraction of individual metals such.ascopper. The result is that solvent extraction must now be regarded as a proven hydrometallurgical technique for the recovery of base metals, and in particular copper. The first significant event in the application of solvent extraction to base metals was the production by General M. Inc. of a compound, designated LIX-63 (R)(1), which was a specific extractant for copper from ammoniacal sns. This did not find a wide application, however, because copper solutions with a pH in the applicable range we more readily treated by conventional techniques.

Jan 1, 1970

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011