Search Documents

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

By J-S Han, J-M Yao

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Shagou deposit is located along NE-trending faults within the high-grade metamorphic basement of the Xiong’er Terrane in the Qinling orogenic belt. It is a large Ag-Pb-Zn deposit hosted in the Taihua Supergroup and has proven reserves of 1.54 Mt of ore with grades of 767 g/t Ag, 13.24 per cent Pb and 4.31 per cent Zn. The hydrothermal ore-forming process can be divided into early quartz-pyrite, middle quartz-polymetallic sulfides and late quartz-carbonate stages. Four types of fluid inclusions (ie pure carbonic, carbonic, pure aqueous and aqueous) can be distinguished in quartz. Fluid inclusion, hydrogen, oxygen and sulfur isotope systematics indicate that the ore-forming fluids are initially deeply sourced metamorphic water with meteoric water gradually mixed in the later stages. Sulfur isotope data show that the ore-forming fluids originated from both the Taihua Supergroup and the sedimentary successions of the Guandaokou and Luanchuan Groups (CSC) located to the south of the Machaoying Fault. A genetic model of the Shagou deposit is proposed as follows: CSC subducted northward along the Machaoying Fault beneath the Xiong’er Terrane during the Mesozoic collision between the North China Craton and South China Block. Subsequent dehydration resulted in the devolatilisation of fluids rich in CO2. These fluids migrated upwards, reacted with the Taihua Supergroup and formed the Shagou deposit.CITATION:Han, J-S, Yao, J-M and Chen, H, 2015. Fluid inclusion and isotopic constraints on the mineralisation of the Shagou Ag-Pb-Zn deposit, Henan Province, China , in Proceedings PACRIM 2015 Congress, pp 615–618 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By T Graham

Traditional iron ore wet beneficiation plants are large multilevel structures, often integrated into centralised processing plants. They are characterised by sizeable footprints, substantial water and power consumption, inflexible design and low scalability. Significant design changes that address these issues need to be made before relocatable modular plants become feasible. Firstly, large amounts of processing water are required in standard wet plants, so it is vital that water consumption is reduced to an absolute minimum. Secondly, the process of depositing tailings into tailings storage facilities (TSFs) is environmentally destructive, consumes significant power and requires lengthy approvals to be completed. Thirdly, modules need to be easily and quickly relocatable.The solution to reducing water usage and eliminating TSF requirements is accomplished by providing a tailings dewatering and dry-stacking capability into a separate module. This equipment needs to dewater tailings to a point (typically below 20 per cent moisture) where dry stacking becomes possible – design is mainly driven by material rheology and particle size distribution (PSD). In this respect, a flexible and scalable strategy is employed to dewatering modules, allowing a variety of components such as dewatering cyclone clusters, paste thickeners, fine mesh vibrating screens and filter presses to be used to achieve the necessary moisture level, enabling the final dry stacking to be accomplished by a simple telescopic stacking system. Plant relocatability also requires modules to comply with mass and dimensional constraints, as well as ‘plug and play’ ease-of-use features.For coarse particle upgrade, jigs provide a low-cost and effective solution, whereas fine and ultra-fine Fe units can be recovered using Wet High Intensity Magnetic Separation (WHIMS). Recently, sensor sorting – a dry process using X-ray fluorescence, X-ray transmission, laser or other sensors – has begun to make an impact in coarse particle separation, although capacities are still low. The overall objective of a plant is to provide an Fe upgrade of four to five per cent with a feed of up to 4 Mt/a and a recovery of approximately 50 per cent.CITATION:Graham, T, 2017. Relocatable modular beneficiation creates value from waste, in Proceedings Iron Ore 2017, pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Cretaceous to Cenozoic sedimentary basins in Western Southland include a wide range of non-marine and marine sediments, in a structurally complex setting dominated by major fault systems. A reassessment of their mineral potential confirms large quantities of nonmetallic minerals (limestone, aggregate, marl), and smaller reserves of bituminous coal, lignite, clays, and oil shale. Hydrocarbon potential is largely untested. Metallic minerals are present in trace amounts, apart from platinum group minerals and some detrital gold. In the offshore area, seismic data suggest the hydrocarbon potential is significant. The Orepuki area has the most interest onshore.

Jan 1, 1992

By G Q. Xie, J W. Mao, Y B Cheng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The East China Mesozoic metallogenic province hosts the world’s largest resources of tungsten, tin, molybdenum, antimony and bismuth, with additional important gold, silver, mercury, lead, zinc, copper, uranium and iron deposits. These deposits form several giant metallogenic belts, including South China, Middle-Lower Yangtze River Valley, East Qinling-Dabie, eastern North China Craton and North-east China. Available data demonstrate that these metallogeneic belts are the products of episodic magmatic and related hydrothermal events between ~240 and ~80 Ma. Each magmatic-hydrothermal episode has produced distinct deposit assemblages that can be readily linked to the Mesozoic geodynamic evolution of East China, involving continental collision between the North China Craton and South China Block at 220–200 Ma, oblique subduction of the Izanagi plate under the Eurasian continent at ca 170–135 Ma and post-subduction extension and lithospheric delamination at 130–80 Ma. Metallogeny in north-eastern China is more complicated due to prolonged tectonic evolution related to southward subduction of the Mongolian–Okhotsk plate and westward oblique subduction of the Izanagi plate, and subsequent continental collision and post-collisional processes.CITATION:Mao, J W, Xie, G Q and Cheng, Y B, 2015. Mesozoic metallogeny in east China and their geodynamic processes , in Proceedings PACRIM 2015 Congress, pp 631–636 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Investigation on Multicomponent Semi-Autogenous Grinding

Sep 13, 2010

By R L. Brathwaite

In New Zealand, volcanogenic massive sulfide (VMS) deposits are found in three main geological environments associated with: 1.   ophiolitic basalts of Oligocene age in Northland and East Cape (eg Pupuke, Pakotai, Parakao and Lottin Point); 2.   with chert and pillow lava in greywacke sequences of Permian-Jurassic age (Torlesse and Waipapa terranes; eg Kawau Island, Te Kumi and Maharahara) and their metamorphic equivalents (Haast Schist; eg Moke Creek and Waitahuna); and 3.   with greenschists (metabasalts) and metaserpentinite of Permian-Triassic age (Ponamu Ultramafics) in Westland (eg Bowen and Wilberg ranges). The deposits consist of small lenses of disseminated to massive sulfide minerals, mainly pyrite and chalcopyrite. Small quantities of copper ore were mined from some deposits in the 1800s (eg Kawau Island from 1846), with the last mining at Parakao from 1961 to 1966. Several deposits have been recently examined for their gold potential with assays on sulfide rock samples as high as 75 g/t Au (Lottin Point).

Jan 1, 2005

By R Cunningham

The E26 Lift 1 North Project took 37 months from the approval on 1st January 2019 to the commencement of production on 1st March 2022. This was five months ahead of the feasibility plan. When compared to the previous E48 Block Cave construction 12 years prior, which was of a similar size and design with ten extraction drives, crusher and conveyors, the E26 Lift 1 North project has been delivered at 29 per cent less capital cost. Key metrics achieved by the project include 12.7 km of development, 240 km of production drilling for drawbells and undercut blasting, 107 drawbells fired ready for production as well as only three Lost Time Injuries compared to 16 during E48 construction. The Lift 1 North Project Team has established a significant point of difference with the delivery being completed by the ‘Owners Team Model’ not Lump Sum or Turn-key. E26 Lift 1 North is now supplying the Northparkes processing plant for the next eight years. This paper discusses major milestones achieved throughout the process, modifications to processes from previous block cave construction at Northparkes as well as novel approaches to work to achieve the successful delivery of the project.

Mar 29, 2023

By E N. Isaev, L E. Levin

New data on the geology of the Late Jurassic to Holocene sediments cover of the World and associated mineral resources (oil, gas, ferromanganese nodules, ores of massive sulphides and other metals) have been compilled in the Atlas at scale 1:25,000,000 and 1:10,000,000. The work was performed by scientists from four Institutes of Russia (VNIIzarubezhgeologia, VNIIoceangeologia, Vernadsky Institute of Geochemistry and Analytical Chemistry of theRussian Academy of Sciences and Geological Institute of the Russian Academy of Sciences). The Atlas shows variation of thickness and formational composition of the large complexes (Upper Jurassic-Early Cretaceous, Upper Cretaceous Eocene, Oligocene-Neogene, Pliocene-Pleistocene), distribution of oil/gas and ore deposits in each complex, data of deepsea drilling (leg 1-130),  thermo-pressure condition in the sedimentary basins within Circum-Pacific Rim.

Jan 1, 1995

A key issue in maintaining the mining industryÆs social contract to access community-owned resources, is the need to be able to demonstrate professional management of resource extraction and the risk associated with mining hazards. Significant failures such as disease relating to coal dust and asbestos and mine disasters such as Moura, Appin and Gretley have resulted in judicial and legislative interventions that respond to the community outcry but do not necessarily effectively manage the longer term risk in a sector driven by new technology. With the implementation of recent amendments to the Queensland Professional Engineers Act, senior engineers in all industries including the mining industry are required to be registered and to demonstrate that they have æmaintained competency in the practice of engineering in the area of engineering for which the (engineer) is ... registeredÆ. This may be facilitated through a report produced by an æAssessing EntityÆ. These entities are approved by the Minister on advice from the Board of Professional Engineers, Queensland. Engineers Australia and The Australasian Institute of Mining and Metallurgy (The AusIMM) are the two professional bodies approved as æassessing entitiesÆ charged with facilitating successful implementation of the process established by the legislation. The scope of the legislation covers engineering enterprises in Queensland and engineering activities elsewhere that may have been designed in Queensland. There is currently a challenge to determine what the necessary health and safety competencies for the mining industry are and how the maintenance of these competencies will be assessed. The different approaches taken by the two assessing entities are compared and contrasted. At the legislative level, establishing an obligation to assess professional competency is simple, but at the level of the profession, it is new ground that warrants a substantial research and development input. The challenge is to develop criteria by which the quality of such system can be assessed. The comparison is made by considering such issues as equity, effectiveness, efficiency, objectiveness and transparency. These five indicators are considered in terms of how they are applied in other sectors and how they might be applied in the mining sector.

Jan 1, 2009

Beneficiation of Iron Ore - Washing with Surface-Active Agent The stability of the dispersed phase in 10 wt per cent slurry of iron ore slime and fines was studied at pH 5 and different concentrations of surface-active agents. The behaviour of the dispersed phase of iron ore slime and fines is different for different surface-active agents. The improvement of iron value of slime and fines in the presence of surface-active agent is best realized at pH 8, where the Al2O3/Fe and Al2O3/SiO2 ratios in the concentrates are appreciably reduced. The polar functional group like -COO- interacts with hematite surfaces and forms outer- and inner-sphere surface complexes depending on the suspension pH and adsorbate.

Sep 13, 2010

By Y Chen, G Xu, B Albijanic

High concentrations of airborne coal particles is the main reason leading to health and safety hazards in underground coalmines. Water spray is one of the effective methods to suppress coal particles in mine sites, but the use of plain water is not effective enough to capture coal particles. By adding surfactants, coal wettability can be improved which will increase the coal dust suppression efficiency. In this study, a modified sink test was employed to evaluate coal wettability in the presence of two anionic surfactants: sodium dodecyl sulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS). Sink rates were calculated by measuring sink weight over test time. Different surfactant concentrations (0.01 per cent, 0.05 per cent, 0.1 per cent, 0.2 per cent and 0.4 per cent) and two types of water (tap water and deionised water) were selected to investigate coal wettability over three size ranges (0–38, 53–75 and 75–90 µm). The results show that both SDS and SDBS surfactants can lower the water surface tension and improve coal wetting performance. Sink rates increased as the surfactant concentration increased, and surfactant solutions prepared by tap water performed better than deionised water in enhancing coal wettability. Also, coal wettability varied for different coal particle sizes; the smaller coal particles were, the worse the wettability they possessed.CITATION:Chen, Y, Xu, G, Wang, R and Albijanic, B, 2017. Study on coal wettability for dust suppression in the presence of surfactants by sink test, in Proceedings Australian Mine Vent Conference 2017, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By K F. Tang, J-W Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Xiong’ershan district in the southern margin of the North China Craton (NCC) contains more than 20 gold deposits hosted in the late Neoarchean to early Palaeoproterozoic amphibolite facies metamorphic rocks or late Palaeoproterozoic unmetamorphosed volcanic rocks. Gold mineralisation consists mainly of auriferous quartz veins and disseminated ores in hydrothermally altered zones, with additional gold mineralised breccia pipes. Gold orebodies are strictly controlled by secondary- or higher-order brittle/ductile-brittle faults. Isotopic dating reveals two separate episodes of gold mineralisation: the Shanggong and Dianfang deposits formed in the range of 236 ± 1.4 to 202 ± 18 Ma, whereas the Gongyu, Qianhe and Qiyugou deposits formed between 135.0 ± 0.5 Ma and 124.0 ± 1.0 Ma. Stable isotope and noble gas geochemistry studies indicate that the Triassic gold deposits were precipitated from deeply-sourced, low-salinity fluids at 250–350°C, but whether the fluids were mainly derived from metamorphic devolatilisation or magmatic degassing remains unresolved. In contrast, the Early Cretaceous deposits most likely precipitated from a dominantly magmatic fluid, although metamorphic and meteoric components cannot be ruled out. Results from this study, when combined with regional geological and geochemical data, suggest that the Triassic gold mineralisation was generated by the deformation associated with the collision between the North China and Yangtze cratons, forming the Qinling-Dabie orogen. In contrast, the Early Cretaceous gold veining was a result of lithospheric destruction of the NCC, a process initiated by plate subduction from both the south and north since late Palaeozoic but ultimately triggered by the westward subduction of the palaeo-Pacific plate in the late Mesozoic. This study helps to reconcile the long-term debate on the timing, genesis and geodynamic setting of gold mineralisation in the Xiong’ershan and other districts along the southern margin of the NCC.CITATION:Li, J-W and Tang, K F, 2015. Gold deposits in the Xiong’ershan District, Southern North China Craton – products of Triassic deformation and Cretaceous craton destruction, in Proceedings PACRIM 2015 Congress, pp 341–344 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

The resource industry must prepare for the inevitable shift towards automation as an operational objective. Although this may seem like a distant concern, many mining companies and equipment manufacturers are already conducting full-scale automation trials. The necessary technology is advancing at a rapid pace yet the training of people to support it at the trade level lags far behind. Those given the responsibility of installing and maintaining automated equipment in the mining environment require a unique set of skills and knowledge. These training needs demand attention to ensure that the wider uptake of automation is sustainable and achieves its full potential.   This paper documents work undertaken by CRCMining and the Mining Industry Skills Centre towards establishing a training framework seeking to address the needs of trade level personnel tasked with the support of automation equipment. A comprehensive definition of the skills and knowledge required by the hypothetical automation-specialised tradesperson is presented. The training pathway identified for these personnel is also described. This work forms part of the Mining Industry Skills Centre's Automation Skills Formation Strategy, funded by the Queensland Department of Education and Training.

Jun 1, 2010

Bioremediation of Acid Mine Water Using Fly Ash and Desulfotomaculum nigrificans One of the major concerns for the mining industry especially after the mine closure is the generation of acid mine drainage (AMD), and its discharge into the environment surrounding the abandoned mines, leading to serious environmental pollution. AMD is usually characterized by high concentration of dissolved metal ions, sulfate and low pH. The efficacy of fly ash was assessed for the removal of metal ions such as iron, zinc and copper as well as sulfate from synthetic acid mine water. Complete removal of ferric and ferrous, 80 per cent of Zn, 83 per cent of Cu and 62 per cent sulfate removal could be achieved, with a concomitant increase in the pH value from 2.3 to 7 using fly ash as an adsorbent under appropriate conditions. The free energy of adsorption of the metal ions onto fly ash was found to be negative, while the adsorption process was endothermic and adhered to the Lagergren pseudo-first order rate equation. Bioremediation studies using a typical sulfate reducing bacterium namely Desulfotomaculum nigrificans, after pre-treatment of the synthetic acid mine water with fly ash, cumulatively resulted in about 94 per cent zinc, 100 per cent copper and 90 per cent sulfate removal. The possible mechanisms of metal ion removal and sulfate reduction from acid mine water utilising Desulfotomaculum nigrificans are discussed.

Sep 13, 2010

The Australian mining industry faces skills shortages across a broad spectrum of disciplines and levels, as it enters another major growth phase. Critical amongst the areas of most significant shortage in the professional sphere is the discipline of geotechnical professionals. More mines, deeper mines, ageing workforces are all contributing to this chronic shortage. But the shortage is not just at the operating sites, it is across a range of employment fields including sites, head offices, consultants, researchers and educators. This paper reviews the status of a number of these fields and explores some of the issues being faced. The different roles of a site geotechnical professional and a specialist geotechnical consultant are explored, together with some of the trends in terms of how such people are operating, and the skills they are expected to have to fulfill their job requirements. The paper also considers the move towards possible mandatory statutory geotechnical positions at mine sites and some of the implications if this were to come into force. Finally, the paper considers the current provider programs for mining geotechnical education, and how additional offerings are going to be needed in order to address the current shortages and the inconsistencies in terms of job expectations for people assigned to geotechnical roles without adequate education and training.

Nov 25, 2010

Laboratory scale flotation tests were done on mineral hematite and aspecular hematite ore using oleic acid and sodium oleate as collectors. The mineral hematite floated strongly in the neutral pH region, with an increased pH range of flotation at higher oleate additions. Concentrates with sufficient hematite grade to meet the paint pigment specification were produced using oleic acid and sodium oleate as hematite collectors on the specular hematite ore. Hematite recoveries of 70 per cent at 60 per cent Fe grade were obtained using stagewise roughing. The interaction between hematite and oleate was confirmed as chemisorption but the exact mechanism could not be determined, as two independent phenomena can be used to explain the fact that the pH of maximum grade increased with increasing oleate addition.

Jan 1, 1999

By R C. A Minnitt

This paper illustrates the use of variography and moving average plots as an aid to analysing variations in the process that can be used to direct the improvement efforts. The hydrometallurgical processes used in manganese metal production consist of sequential unit operations that include milling and reduction of manganese ores. Leaching of the reduced ore, is followed by solid-liquid separation, residue disposal, solution purification and electrowinning of manganese metal completes the process. The nearly 250 integrated process control loops rely on reports of pH, flow pressure, level, temperature and chemical analyses. Metallurgical accounting, reconciliation and process control is achieved through monitoring of the chemical and mass balances within the manganese reduction plant, requiring approximately 50 000 analyses of solids, powders and liquids each month. The largest numbers of samples are taken in the cell house. Changes and variations monitored by sample statistics ensure that the manganese products comply with predetermined specification limits. Optimising the information-value of the approximately 50 000 samples in the manganese plant is carried out in tandem with ongoing process optimisation. Variographic analysis of daily sampling data suggests that the cyclical behaviour evident in the moving average plots is only a reflection of random residual variability and not a reflection of true underlying variability related to cyclical phenomena. Low resolution in the variogram of daily sampling data masks the short-range variability that emerges when hourly data are analysed. Hourly samples collected over a 39-day period (giving 941 sample data), helped identify short-range cycles in the process. The relative distribution of variability for daily sample intervals, indicate that 57 per cent arises from V[0], 18 per cent from V[process] and 16 per cent from random residual variation. V[0] includes all the uncontrolled sampling error arising from a poor sampling protocol, the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. This confirms the suspicions regarding the suboptimality of the sampling protocol and the way it is implemented. The absence of long-term trends in the leach suggests that short-term variation (less than one day) dominates the process. While the control charts indicate that the overall processes are maintained above the lower specification limits and the target values, there is nevertheless a considerable amount of variability in the system that overhangs the processes and threatens to impact them negatively. Although the variability in the leach is above the prescribed limits, the volatility is a matter of concern because it seems to be uncontrolled. The comparison of the various sources of variability in data collected on an hourly basis suggests that the short-term random variability (V[0]) accounts for almost 50 per cent of the variability in the process. The main source of this variability is due to errors in the sampling protocol and is probably related to the size of the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. Remediation of FE and GSE will probably lead to a reduction in V[0], whereas V[process] could be mitigated by reducing the biases associated with DE and EE in particular.

Jan 1, 2008

By Jarc H

The steeply dipping silver/lead/zinc orebodies at Mount Isa mine have been extracted most recently by a combination of cut-and-fill and open stoping methods. Bench stoping was first used at Mount Isa Mine seven years ago to allow safe extraction of a highly stressed cut-and-fill stope. Subsequent benches have shown that the method offers significant cost and safety benefits through increased productivity and reduction in man exposure. The success of benching has lead to cut-and-fill mining being replaced at Mount Isa.Significant resources have been focussed to optimise benching. This paper describes the operational, planning, and research and development aspects which have contributed to the method to date. A brief look is also taken at the future direction of benching at Mount Isa.

Jan 1, 1992