Search Documents

William Frederick McBryde Broun, a graduate of the Royal School of Mines, was employed on the staff of the Mount Morgan Gold Mining Company for some years prior to 1912, and will perhaps be remembered by some of those who attended the Mount Morgan meeting of the Institute in 1910, as an Associate Member present on that occasion. He severed his connection with the Mount Morgan Company in 1912, and was returning to England via the East Indies, when he contracted typhoid atSingapore and died at Colombo.Years later some old papers were being turned out in the office where he had worked, when a set of M.S. notes in his unmistakeable handwriting came to light. On examination these appeared to be the rough draft of a paper he must have beenpreparing for the local branch of the Institute, which he had not been able to complete. The notes were very rough. Apparently it was the author's intention to fill in numerous gaps with extracts from sundry published articles on Cornish mining; theextracts were missing and only the written portions linking them together were there. They give a sketch of Cornish mining practice which those who wish may supplement (as the author would have done) from Le Neve Foster and other well-knownsources. The fragmental notes which have been pieced together as carefully as possible by Mr B G Patterson, Hon Secretary Mount Morgan Branch; are as follows :-The first mine the author worked at was Carn Brea, in 1904."This is one of the largest tin mines in Cornwall, and belongs to the Carn Brea and Tincroft Mining Co, which also owns Cooks Kitchen. The mine was started in 1832, but had been in a bad way for several years previously, and had just begun to recover...

Jan 1, 1919

By Burns K. L

Keyboard patterns of hundreds of minor faults with vertical displacements of 3 mm to 2 m occur within the Greta coal seam and cause serious mining problems in collieries. Many of the faults are concentrated in linear zones termed swarms. One swarm is 600 m wide and more than 800 m long and others are of comparable size.The minor faults between the swarms are normal and are relatively widely spaced and show dip-slip movements, but the faults within a swarm are clustered and show strike-slip and oblique-slip movements. Fault swarms ofthis size and frequency have not previously been described from the Sydney Basin or on a comparable scale elsewhere but appear to be a widespread phenomenon in Australian coalfields. The faults are assigned to classes onthe basis of orientation which are then assigned to sequential phases I to IV on the basis of offsetting relations between representatives of each class. Phase I faults are minor thrusts. Phase IT, Ill, and IV faults are concentratedin the swarms and show sinistral strike-slip and normal dip-slip movements. The interference of slickenlines indicates that multiple movements have occurred within a single phase; their order is (i) strike slip (ii) dip slip and (iii) oblique slip. All faults truncate and post-date both cleat and sedimentary "stone" dykes.Phase I minor thrusts trend at a high angle to the Hunter Thrust and are considered to predate the Late Permian movements on the Hunter Thrust. Phase II and III minor faults are younger and may be any age between the latePermian and Tertiary.

Jan 1, 1978

By H Susanto, N Belluz, D Flint, A Edw

The Deep Ore Zone (DOZ) is a block cave mining operation exploiting a diluted reserve of 131 million tonnes grading 1.06 per cent copper and 0.81 g/t gold in the lower portion of the Ertsberg East Skarn System (EESS). The EESS is a calcium-magnesium silicate skarn containing in excess of 250 million tonnes of copper-gold ore, located in the Ertsberg Mining District on the crest of the Jawawijaya mountain range in the highlands of Irian Jaya, Indonesia. The EESS was discovered in 1968 where it cropped out at an elevation of 4050 metres above sea level. The Ertsberg Mining District is underlain by siliclastic carbonate and siltstone formations of Jurassic to Tertiary age. The sediments have been folded and are cut by major bedding subparallel and crosscutting structures. Intrusion of a series of igneous bodies post-dates folding and faulting. These I-type intrusions are the source for the copper-gold mineralisation found in the Ertsberg Mining District. The EESS is hosted by carbonates of the Tertiary Waripi and Faumai Formations that have been altered to calcium-magnesium silicate skarn and is situated on the southern limb of a northwest-trending syncline. The EESS is an essentially vertical tabular body with a vertical extent of at least 1200 metres and a lateral extent of up to 1000 metres. The width of the EESS averages 200 metres and locally is in excess of 300 metres. The northeast (hangingwall) contact of the EESS is a skarn reaction front in sudden contact with barren marbles. This contact coincides with a zone of localised faulting and brecciation. The EESS is bounded to the southwest (footwall) by the Ertsberg Diorite, a 3.25 Ma old intrusive. The DOZ block cave operation extends from 3040 metres above sea level to a maximum of 3388 metres above sea level, has a length of 860 metres and a maximum width of 350 metres. The DOZ is a high temperature skarn with a prograde forsterite/diopside mineralogy whose protolith is the dolomitic Tertiary Waripi Formation. The principal retrograde alteration minerals include tremolite, actinolite, serpentine, talc and chlorite. Grade is highest where bornite occurs in large dense complex intergrowths with magnetite and anhydrite. Grade has been locally enhanced in the DOZ by a late-stage pyrite-chalcopyrite hydrothermal alteration event with associated brecciation. Ertsberg Diorite along the footwall of the skarn is also included in the reserve where it is mineralised endoskarn or has been mineralised by porphyrytic or late stage hydrothermal alteration. Formation of the EESS was initiated by contact metamorphism during the intrusion of the Ertsberg Diorite with later metasomatic alteration during both prograde and retrograde phases. The bulk of sulphide mineralisation formed late in the retrograde phase. The EESS is open along strike to the northwest and down-dip with on-going exploration of these areas. Current exploration is targeting both endoskarn and porphyry style alteration and mineralisation of the Ertsberg Diorite.

Jan 1, 1999

Electro-Flotation Research on Fine Cassiterite

Sep 13, 2010

By C J. Hogan

Increasing demand for fine grinding to improve mineral liberation and metal recovery and the need for stricter control of the environmental impact of tailings deposition poses problems for tailings disposal. This has led to an increasing number of investigations of properties of tailings and their disposal. This paper describes laboratory model testing undertaken on Macraes mine flotation tailings to provide information on tailings behaviour under conditions of subaerial deposition. The in-place density or 'dry density' of the impounded tailings and the impoundment depth relationship are important for utilisation of the available impoundment storage facility and results of dry density to depth relationships are given for the Macraes mine tailings impoundment.

Jan 1, 1993

E. W. Stutchbury (Internationa~ Oombustion Aust. Ltd.) : Mr. Callcott made particular mention in his paper of erosion in primary air fans which are placed after the mill discharge. He adds that subsequent reduction in plant performance and resulting increased maintenance costs occur. It is generally assumed that this statement is substantially correct as the fan handles the complete output from the mill, but with modern materials, reduction in performance and subsequent .maintenance are not now a problem. This consideration of handling the pulverised coal in the fan is more than offset by the advantage of operating the mill under suction which results in cleaner operating conditions, simpler feeder arrangements and elimination of complicated seals on the mill.and feeder unit. It should be specially noted that whereas mill exhausters in the past have used chequer plate blades (sometimes with the addition of hard facing by electrode deposit) it is modern practice to provide fan blades of up to 1 in·. thick Ni-hard suitablyheat treated, with the circumferential section of the fan also in Ni-hard. By the use of this material large power...

Jan 1, 1957

The Waimumu area, 12 km southwest of Gore, is underlain by the Gore Lignite Measures, an early Tertiary fluvial sequence approximately 500 m thick resting on Triassic-Jurassic argillitic basement. The Waimumu Quartz Gravels (Pliocene) have been deposited locally and are in part due to the localised reworking of the Gore Lignite Measures. Structurally the area is dominated by the Dunsdale Fault System, a steeply dipping series of NE trending reverse faults (Isaac and Lindqvist, 1990). The Belle-Brook, Hedgehope and Parker Road sites sampled are adjacent to the downthrown (east) side of the Hedgehope Fault.The authigenic gold-sulphide association at Belle-Brook was discovered in 1987 (Falconer, 1987: Clough and Craw, 1989). Despite a very limited amount of alluvial mining a significant quantity of authigenic marcasite has developed. Authigenic sulphide trace element analysis has shown anomalous amounts of As, Ni, Cr and to a lesser extent Zn, Pb and eu (Table 1). It has been established that the nickel occurs as a colloform banded Ni sulphide, possibly bravoite, within the marcasite (Figures 1 & 2). Arsenic and nickel (re)mobilisation are well documented in the literature. Generally As and heavy metals are mobilised in the groundwater as a result of the oxidation of sulphides (ie as a result of mining). At Belle-Brook it is reasonable to assume the authigenic sulphide trace element composition reflects either localised groundwater contamination or hydrothermal mineralisation. This poster presents some preliminary findings.

Jan 1, 2001

The selection of Sydney and Port Kembla for the First Ordinary Meeting of the Institute for 1938 was, no doubt, a recognition of the celebrations marking the 150th Anniversary of the first settlement of this country. In selecting a theme for my Presidential Address, I propose to depart from the precedents of my distinguished predecessors, as I feel that this year of celebration is the natural year for a brief review of the history and progress of the Institute.In July, 1892, the Amalgamated Mining Managers' Association of Australasia held its Annual Conference in Ballarat, Victoria, when Mr. Uriah Dudley, who attended as a delegate from Broken Hill, brought forward the advisability of the formation of an Australasian Institute of Mining and Metallurgy. Mr. Dudley was authorised to take such action as he thought fit, and the result was the formation of a Provisional Committee in Broken Hill of men who were mostly members of the American Institute of Mining Engineers. Broken Hill was therefore really the birthplace of the Institute.A circular headed Broken Hill, September, 1892, with the signature of Uriah Dudley, Acting Hon. Secretary, Provisional Committee, which was sent to those likely to take an active part in the formation of an Institute, read as follows:-The Mining Managers' Association of Australasia has suggested that the time has now arrived when an Australasian Institute of Mining Engineers should be established, having objects similar to the American Institute, of which all of the Thirty-one Colonial...

Jan 1, 1938

The additional information that Clarke and Taylor (1982) provide about the important but poorly documented Ardlethan deposit is, of course, very welcome. However their contention that structural considerations, in conjunction with petrology, alter the interpretation of the mineralogical and geochemical data presented previously (Scott, 1981) is not accompanied by adequate supporting evidence. Indeed characteristics of the orebodies studied invalidate their arguments.Heterogeneity between matrix and fragments is not a problem in the South Cherry and Ardwest orebodies because most samples are comprised entirely of interlocking hydrothermal assemblages with a fabric and mineralogy that is uniform through both former breccia fragments and matrix. In hand specimen, the rock superficially resembles altered granite and, as indicated by Clarke and Taylor (1982), a brecciated texture is difficult to discern. In thin section, relict brecciated textures can be observed as localized changes in the grainsize or in the distribution of minerals that outline former breccia fragments (P. J. Eadington, 1982, personal communication).Because of the intense brecciation and comminution of rocks (fragments < 10 mm are usual) in the South Cherry and Ardwest breccia bodies, hydrothermal recrystallization was complete, resulting in homogenization of fragments and matrix. Furthermore, the amount of sample analysed (-100 g for drill core and 2-3 kg for hand specimens) is sufficiently large to be representative of both former breccia fragments and matrix. The Carpathia and Stackpool orebodies, with their abundance of sedimentary fragments, have alteration superimposed on a heterogeneous fabric, and were not studied. Thus the problems of differentiating between fragments and matrix (Clarke and Taylor, 1982) are irrelevant to the particular orebodies described in my paper.Within the alteration halo, which is several hundred metres wide (Paterson, 1976), the very uniformity of the alteration assemblages implies that subsequent, postmineralization brecciation is of only minor significance.Indeed tourmaline pipes in the Ardwest pit are less than several metres across (Clarke, 1979) and produce minimal alteration in the surrounding rocks. Therefore the interpretation of the mineralogical zonation is not compromised by the recognition of several periods of brecciation.

Jan 1, 1982

By U König, N Norberg

To cope with varying raw material qualities and increasing prices for energy, a more frequent and accurate monitoring of the processing of iron ore became the focus in sinter plant operations. Traditionally, quality control in iron producing industries has relied on time-consuming wet chemistry or the analysis of the elemental composition. The mineralogy of a sinter that defines the properties and behaviour in the blast furnace is often not frequently monitored. One fast method to analyse the mineralogical composition of iron sinter, raw mixtures and iron ores is X-ray diffraction (XRD). Recently statistical methods such as similarity analysis or partial least square regression (PLSR) in combination with XRD raw data has become more and more popular in handling large amounts of data and correlating process-relevant parameters directly with an XRD measurement. PLSR can be used to correlate process parameters directly from the XRD pattern without investigating the mineral content. Hidden information that is present in the measurement but not determined with traditional methods can be used to improve the characterisation of the analysed materials.CITATION:König, U and Norberg, N, 2017. Iron sinter process control using X-ray diffraction – part : monitoring of low temperature degradation, in Proceedings Iron Ore 2017, pp 75–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

This paper gives a description of the methods of mining employed at North Broken Hill Limited, Broken Hill, N.S.W.GEOLOGICAL NOTESThe main Broken Hill lode occurs as a replacement of tightly folded pre-Cambrian sediments. Replacement has followed certain stratigraphical horizons and the main bulk of the ore is found where these have been packed into the noses of anticlinal and synclinal folds.Throughout the mine the ore-bearing folds pitch north fairly consistently at 45 degrees, as a result of which two favourable horizons in the same fold appear in plan as separate orebodies and these are referred to as the "Southern Orebody" and the "Northern Orebody" respectively.The general dip of the orebodies to the west is about 60 degrees. A typical sill is shown in the plan of the 1,400-ft level (Fig. 1).Both the hanging wall and footwall rocks throughout the mine are weak and, as a result, it is necessary that the hanging wall must be well supported after ore extraction, to prevent subsidence. The weakness in the footwall is confined to a narrow zone, approximately 60 feet in width. This weaknes.q is a source of trouble in the development headings which pass through it, It is sufficiently crushed to transmit weight from the overlying wall to the gangways below.Another feature causing ground instability is the presence of many faults. Although their effect on the shape and character of the orebody is relatively small their...

Jan 1, 1940

By N Cusworth

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines û mining, metallurgical, chemical, civil, electrical, mechanical and environmental û as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies û and hence no two development projects û are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource projectÆs development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as ædoing a feasibility studyÆ. But the principal purpose of a æfeasibility studyÆ is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant û they are a prerequisite to the demonstration of a projectÆs viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of æfeasibility studiesÆ and provide guidance to minimum standards and best practice.

Jan 1, 2007

Engineering education has become a matter of national concern, at last, so I would like to talk about the links between the mining industry, the universities and technological developments. The Australasian mining industry and the mining schools have collaborated closely since the first school was established in 1871 and during those years there were a series of remarkable technological developments. For example:In the late 1880s George AndersoIl Richard developed chloride leaching of gold at Mt Morgan. This made a large difference to the wealth of Mt Morgan Mining Ltd.In the mid 1890s Robert Sticht demonstrated that pyrite smelting was an economically feasible process at Mt Lyell and the wealth which came to Mt Lyell Mining Co from his outstanding work made it one of the great companies in the country.During the first 15 years of this century flotation was developed at Broken Hill and it has proved to be one of the great technological inventions of this century.In the 1920s G K Williams started his outstanding work on lead smelting and refining at Port Pirie, this was work which ultimately re-wrote the text book on lead metallurgy and established Port Pirie as the mecca for lead metallurgists.In the 1920s also Frank Stillwell, later joined by Austin Edwards, established the new science of mineragraphy at the University of Melbourne. They were both great geologists, both were superb scientists and oddly enough both were outstanding athletes.In the 1930s Dr Ian Wark, a man in the front rank of Australian scientists of any period, started his outstanding work on flotation, work which resulted in a text book which remains a leader in its field today.In the 1930s also Arnold Black at Broken Hill South Ltd picked up the work which had been done at Mt Lyell many years previously and eventually wrote the papers on hydraulic fill which demonstrated that he led the world in fill technology. What a remarkable story of achievement it was, it laid the groundwork for the great industry we have today. It was possible because the industry was well supported by outstanding university schools and I would like to talk about some of these.

Jan 1, 1989

Role of Bubbles in the Action of Flotation Agents

Sep 13, 2010

Drill blasting is a widely used method for rock fragmentation in mining, quarrying and construction industries. Environmental effects such as air shocks, dust, flying rocks and ground vibration are unavoidable results and undesired effects of blasting. Among these ground vibrations can have a damaging effect and may influence on long distances. Therefore various researchers have developed mathematical models to predict ground vibration after blasting. These models take into account the amount of explosive, distance and several coefficients related to the field under investigation. The developed models to predict ground vibration may yield different results for the same case. Selection of the most suitable model requires engineering judgment and evaluation of models. At this point, a computerised system helps the engineer to evaluate and select the most suitable model in order to design and plan a blasting pattern. The safe charge of explosive and magnitude of vibration after blasting should be predicted beforehand. Therefore a computer program namely 'prediction of blast induced vibration' (P-BIV) has been developed. This paper introduces and presents a computer program (P-BIV) which includes the set of models developed to estimate ground vibration to provide blasting engineers a tool to determine the amount of explosive for safe blasting.

Dec 6, 2010

By J S-L Chan, J C. T Chu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. In its industrial days, Hong Kong’s mining industry was thriving, benefitting from the mineral occurrences that are related to the regional Mesozoic igneous and hydrothermal activities.Hong Kong was unique in the mining sector as it was so small in landmass but with such a rich variety of commodities discovered. There are records of commercial exploitation of tungsten, iron, lead, silver, beryl, graphite, quartz, feldspar and kaolin in Hong Kong before 1981. Of these, most of them are located in the New Territories.The Lin Ma Hang lead mine was operated in the 19th century by the Portuguese and was abandoned in 1958. The Needle Hill tungsten deposit was discovered in 1935 during construction of the Jubilee Reservoir. The Ma On Shan iron mine, which operated for 70 years between 1906 and 1976, was the largest mine in the history of Hong Kong. The Mui Wo lead-silver mine on Lantau Island can be traced back to the Ming Dynasty 400 years ago. West Brother Island, which extracted graphite from 1952 to 1973, was levelled in the 1990s to make way for the development of the airport at Chek Lap Kok.Nowadays, these mines are disused and abandoned, but this extended abstract reviews the legacy of the mining industry in Hong Kong to understand the impact that it had on techniques, the economy and culture.CITATION:Chu, J C T and Chan, J S-L, 2015. The history of mining in Hong Kong , in Proceedings PACRIM 2015 Congress, pp 109–114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Removal of As(III) and As(V) in Aqueous Solution There are toxic arsenical species such as As(III) and As(V), and arsenious species have specially strong toxicity. The strong toxicity causes contamination of groundwater and water pollution for the semiconductor production process. This study is concerned with the removal of As(III) and As(V) with various kinds of Mg/Al layered double hydroxides (LDH) containing CO32-, SO42-, Cl- and NO3- as interlayer anionic species. The anion exchange property is different from the kind of layered double hydroxides and the Mg-Al-NO3-LDH is superior in the anion exchange property of As(III) and As(V) due to the nature of nitrate ion existing in the interlayer. The pH condition suitable for As(V) removal is 7.1 or more. If the initial conditions such as 10mg/dm3 of As(V) concentration, 7.1 of pH, 1 m3 of amount of solution and 99 per cent of removal are fixed, the required amount of Mg-Al-NO3-LDH is 0.27kg for two step-batch operations. The As(III) is suitable to oxidize to As(V) before the removal processing.

Sep 13, 2010

By H J. Stedman

A Transient Electromagnetic (TEM) geophysical survey was trialled in Bowen Basin Permian coal measures overprinted by Cretaceous intrusion. The trial’s intention was to compare whether TEM could assess residual coal more accurately and economically than drilling.TEM results were promising but had limitations. TEM did not compare to drilling for defining coal thickness or relative level definition. However, TEM resolved conductive anomalies laterally; providing a qualitative picture of remnant coal.Three material types and associated conductivities occur within the trial area: overburden (sandstone/siltstone), intrusive sills and heat affected coal.Ground conductivity was analysed by measuring decay of residual current within the TEM loop. Fast decay related to resistive overburden and intrusion, attenuated decay related to conductive coal.Generally speaking, carbon content governs coal resistivity where good quality, low ash, bright coal is more resistive relative to dull, high ash coal. Though in the trial area, relative to intrusion and overburden, coal was found to be the most conductive of the three materials.By modelling conductive anomalies, a general picture emerged of remnant coal regions. Subsequent highwall exposure reconciled with conductive TEM anomalies.CITATION:Stedman, H J, 2017. Findings from a transient electromagnetic trial for heat-affected coal, in Proceedings Tenth International Mining Geology Conference 2017, pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Robinson KJ

There has been much debate in recent years regarding the number of Geology (Earth Science) graduates produced in Australia. The key variable has commonly been assumed to be the placement of graduates in the mineral and petroleum industries. Although not wishing to deny the importance of this element, we contend that Geoscience studies should be given to a wider variety of graduates. The essence is to make students and future citizens more environmentally aware. INTRODUCTION Geoscience is fundamental to exploration and to the well-being of the minerals industry and hence the Australian economy. The value of mineral primary products exports for the past three years has been: 1895 $15.3 billion 1986 $14.8 billion 1987 $16.3 billion (Data source: B.M.R) The mining industry supplies about 40% of Australia's export earnings. However the overall value of Geoscience to the Australian economy is much greater. At the opening of the ANZAAS conference in Townsville during May 1987, Sir Bruce Watson , Chairman of the Mt. Isa Mines Ltd., made a plea for a national re-examination of the way science is taught in secondary schools. In particular he emphasized the point that the community should be more aware of the importance of Geoscience and the value of the mining industry to Australia.

Jan 1, 1989

By M Furche, U Noell, C Grissemann, J A. Meima, T Graupner, A Romero-Baena

The mining residues at the abandoned copper mine site Pe±a de Hierro, located at the headwaters of the Rio Tinto, contribute substantially to the pollution of the river with high loads of Fe, As, Pb, Zn and Cu. The pH of the outflow ranges from 0.5 to 2.4 in the dry and wet season, respectively. One heap composed of alternating layers, which were deposited parallel to the slope, was investigated in detail. Unsorted blocky to fine materials including gossan material, pyritic volcanics, ashes from pyrite combustion and slate were observed here. The top of the heap has a gentle slope and a hill contouring channel-rip morphology. The initially rugged surface was smoothed by heavy rainfalls filling up the pores of the blocky material with fines. These fines are capable of storing the water for a prolonged time, providing an extended reaction time close to surface in a dry climate at extremely low pH conditions (one to four). All minerals, pyrite, mica, barite and even quartz (probably due to F released from dissolved mica) have been digested and silica gel precipitates have formed a stable and quasi impermeable 100 ¦m layer with very low porosity (<5 area per cent, estimated using scanning electron microscopy (SEM) imaging). The silica layer itself is covered by Fe-oxy-hydroxide (ie FeOOH) coating (10 ¦m) and seals a 1 - 5 mm thick stable hardpan. This hardpan covers the channels and part of the rips almost entirely, guiding the rainwater subhorizontally towards slopes and sinkholes. By geoelectrical measurements, a 3D-resistivity model of the internal structures and the bedrock relief underlying the heap was generated. Internal structures relate to lithological changes in a number of layers. Zones of low resistivity may be attributed to washed-in fines within the mega pore system, whilst zones of high resistivity close to the surface probably reflect the advanced stage of drying beneath aging hardpans. The water movement at the surface was investigated by an artificial precipitation experiment with monitoring of the subsequent changes in resistivities.

Jan 1, 2008