Search Documents

By M. S. Burton, H. H. Kranzlein, G. V. Smith

The influence of up to 2 at. pct of Ni and Pt on the yield strength of mono- and polycrystalline high-purity iron has been evaluated at temperatures from + 25° to -196°C. Current theories of solid -solution strengthening fail to explain the experimental observations. The temperature dependence of yield stress was found to be less in the alloys than that in high-purity iron. The room-temperature yield stress increased with alloy content, but at —78°C the yield strength first decreased with increasing a1loy content. AS a result of many studies, a number of theories have been proposed for solid-solution strengthening. The purpose of the present study was to evaluate these theories, as applied to the solid-solution strengthening observed in Fe-Ni and Fe-Pt alloys. Of various theories of solid-solution strengthening, those of Cottrell,1,2 Fisher,3 Suzuki,4 and Mott and Nabarro5 are most prominent, and have been discussed widely in the literature.'-' Of the recent concepts of solid-solution hardening the work of Fleischer9 is notable. Each of these models has been applied to particular alloy systems with some success, but in general none has proved generally applicable. In many of the previous studies to assess the effects of alloy additions in ferrous systems, lack of adequate control of the purity and grain size of the materials has obscured strengthening effects, so that few comprehensive data relating composition, temperature, and change of lattice parameter have been determined. In the present investigation an attempt was made to obtain data which would be meaningful in evaluating the theories of strengthening. Materials of high purity were used to minimize extraneous impurity effects, and both single crystals and polycrystalline materials were studied to evaluate the effect of grain boundaries. Nickel and platinum were chosen as alloy additions, because both belong to the same chemical group and have the same crystal structure and valence, with markedly different atomic diameters. It appeared that some conclusions regarding atomic size effect on strengthening might be made. MATERIALS AND PROCEDURES Fe-Ni and Fe-Pt alloys containing 0.5, 1.0, 1.5, and 2.0 at. pct alloy additions were prepared from high-purity materials. The iron was supplied by the American Iron and Steel Institute from a stock of 99.98 pct zone-refined iron prepared by Battelle Memorial Institute. The minimum purity of the nickel and platinum used for alloying was 99.98 and 99.999 pct, respectively. Alloys were prepared by levitation melting, cast into cylindrical copper molds, and cooled, all under a partial pressure (0.3 atm) of purified helium. Samples were 0.375 in. in diameter and weighed 20 to 25 g. Chemical analyses of the alloys are given in Table I. A sample of unalloyed iron also was cast as a control specimen.

Jan 1, 1965

By H. I. Meyer, D. F. Searcy

INTRODUCTION The analysls of our previous paper' on the behavior at two immiscible fluids separated by gravity into two dlstinct saturated zones in the porous medium was shown to be theoretically valid only if one of the two fluids was immobile. The practical problems associated with flow of both phases have so far been impossible of solution by these analytic methods. We, therefore, decided to resort to a simulator study to answer the following pertinent questions: 1. If the lighter fluid is produced from a point above the fluid-fluid interface, how long will it take for the heavier fluid to come up to the point where production of both fluids is taking place? 2. After steady-state two-phase production is established, what is the relative production rate of each phase, on what physical variables does this depend, and what are the boundary conditions at the outflow face? 3. A third question was at least partially answered in the course of this investigation: that of the shape of the interface under flow conditions. These questions are of fundamental importance in the fields of hydrology and the reservoir mechanics of oil and gas production. In order to simplify equipment used and still retain a fair physical representation of these phenomena, it was decided to use a Hele-Shaw type of analogy in which the flow took place between two vertically mounted pieces of plate glass. The advantage of this system is that it eliminates any surface effects between the matrix of the porous medium (e.g. packed sand) and also allows equilibrium conditions to be established more quickly. The principle disadvantage (apart from the obvious one of being one more step removed from the prototype) is that our equipment limited us to two dimensional flow studies. In spite of these limitations answers to the questions were obtained which seem adequate for our purposes. We would like to see more work of this nature done to verify and to improve our conclusions. DESCRIPTION OF EQUIPMENT AND PROCEDURE A drawing of the equipment used in this study is shown in Fig. 1. Fluid flow takes place between the two 36 in. x 12 in. pieces of plate glass held apart at the long edges by two spacers of cellulose acetate sheet (Kodapac IV) which is available in several thicknesses. This sandwich was clamped together by small c-clamps whose stress was distributed by long pieces of 3/8-in. keystock. Accurate spacing was obtained by tightening these clamps as indicated by micrometer measurements on the outside of the glass. At the upstream end of the plates a piece of 6-in. diameter pipe simulated an infinite reservoir, while at the downstream end a 2-in. Lucite cylinder with a small hole near the top of the flow region served to drain the fluid. Sealing was achieved by O-rings, the whole system being tightened by pressure on the Lucite tube provided by set screws (not shown in the drawing). The total head

Jan 1, 1957

By Charles R. Keyes

In the dry regions of the globe many silver-deposits display certain remarkable features, which at the same time are so totally unlike anything met with among ore-bodies elsewhere that they hare long presented exceptional dificulties, not only to a satisfactory explanation of their origin, but to economical milling. A most striking peculiarity of these ores is the haloid character of many of their bonanzas. To this fact more than to any other may be ascribed most of the unusual uncertainties of mining-operations in desert countries—the marvelous local richness of the ores under certain conditions and the often abrupt transition to utter poverty; the inadequacy of ordinary prospecting customs and the constant devising of new exploratory methods; the unaccountable losses in smelting and the continual change in treatment-practice. For these anomalies certain climatic conditions seem to be chiefly responsible.

Jan 1, 1912

By George Fowler

THE history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur Co. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico.

Jan 1, 1934

By Wilson Lundy

THE history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur Co. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico.

Jan 1, 1934

By M. D. Hassiaslis

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1-The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2-The orientation of the chemical units at the surface; and 3-The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element-the mobility of the collector units in the two dimensions of the solid-liquid interface.

Jan 11, 1951

By Julian Nardi

Pumping solids through a pipeline is not new but until very recently other means of transportation were cheaper. Many proposed pipelines for transporting solids, while technically feasible, have not been attractive enough to warrant the financial risk involved. In some instances, the difference in transportation cost was negligible. In others, the threat of pipeline competition resulted in a slashing of rates on existing transportation to the point where a pipeline could no longer be justified. In others, a competitive product was cheaper. FIRST IN PLACERS The earliest record of solids being transported in a pipe was in the late 1850s in California placer mines. Water under pressure was used to force gold-bearing gravel up through a pipe, from 30 to as much as 55 ft, to a point where it could be discharged into a flume or sluice.

Jan 9, 1959

Established as a Division November 17, 1948 R Schuhmann, Jr, Chairman A E Lee, Jr, Past Chairman R C Cole, Chairman-Elect H W St Clair, VIce-Chairman, '61 , Vice-Chairman, '62 Paul Queneau, Vice-Chairman, '63 T D Jones, Treasurer R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y

Jan 1, 1960

[A. B. Cummins, President James C. Gray, President-Elect J. W. Woomer, Past President C. E. Lawall, Eastern Regional Vice-President Donald W. Scott, Central Regional Vice-President H. C. Weed, Western Regional Vice-President Nathaniel Arbiter, Treasurer John Cameron Fox, Secretary AIME 29 W. 39 St. New York 18, N. Y. D. R. Tone, Assistant Secretary]

Jan 1, 1961

CARL E. SWARTZ, Chairman D. K. CRAMPTON, Past-Chairman CYRIL S. SMITH, Vice-Chairman ARTHUR PHILLIPS, Vice-Chairman FRANK T. SISCO, Secretary 29 West 39th Street, New York, N. Y. H. A. MALONEY, Treasurer Executive Committee 1943 1944 ERIC R. JETTE WILLIAM C. ELLIS LOUIS W. KEMPF ALAN MORRIS GEORGE SACHS KENT R. VAN HORN

Jan 1, 1942

ROBERT H. LEACH, Chairman ROBERT F. MEHL, Past-Chairman D. K. CRAMPTON, Vice-Chairman E. M. WISE. Vice-Chairman W. M. CORSE, Treasurer LOUIS JORDAN, Secretary 29 West' 39th St., New York, N. Y. Executive Committee 1940 1941 ARTHUR PHILLIPS W. P. SYKES L. E. SCHUMACHER E. A. ANDERSON CARL E. SWARTZ D. L. COLWELL 1942

Jan 1, 1939

By D. B. Masson

THE martensitic transformations occurring in ,B AgCd as a result of cold working at room temp.. a-ture and cooling below room ten1erature have been reported by Masson and Barrett.1 These authors found that simple cooling to 127°K caused body-cen-tered-cubic AgCd containing 53.0 at. pct Ag to transform to an orthorhombic structure, while mechanical deformation at room temperature was found to induce a hexagonal structure. Furthermore, they observed that the temperature at which martensite first appeared on cooling, Ms, and that at which the transformation was complete, MI, as well as the corresponding temperatures for the reversion on heating, As and Af, could be ascertained to ± 1°K, although they report these temperatures only for the alloy containing 53.0 at. pct Ag (51.96 wt pct). In the work reported here the temperature range of the transformation on cooling was studied as a function of composition, and further consideration was given to the relationship between the original bcc structure and the transformation-induced hexagonal and orthorhomic structures. EXPERIMENTAL PROCEDURE All samples studied were in the form of annealed 300-mesh powder and were prepared from the constituent metals in the manner described previously.1 The compositions in weight and atomic pct are listed in Columns 1 and 2 of Table I. Method of determination of transformation temperature was the same as utilized previously1—measurement of the intensity of X-rays diffracted by the transformation product. A diagram of the low-temperature sample mount is shown in Fig. 1. This mount was made to fit a GE model XRD-3 X-ray diffraction unit. The powder sample was varnished to a flat surface on a copper sample holder at A. This sample holder was soldered to a brass rod, B, which was in turn soldered to a second copper rod, C. Rod C could be cooled to 78°K by inserting it into a reservoir of liquid nitrogen, D. A heater coil of nichrome wire was wound at E on the sample holder, and by varying the current through the heater a thermal gradient could be maintained along brass rod B. Sample temperatures from 78°K up could be attained and held as long as needed. The sample holder and nitrogen reservoir were insulated by Styrofoam, F, and the sample itself was protected by two radiation shields, G. The X-ray beam entered and left the sample chamber through windoys in the supporting container at H and I. Sample temperatures were measured by a calibrated copper-constantan thermocouple varnished to the sample holder just out of the beam at A. The low-temperature structure had been found to possess orthorhombic symmetry1 and the expected positions of the diffraction maxima were known. Therefore the sample was aligned in the X-ray beam and the Geiger counter of the spectrometer set to receive the most intense orthorhombic reflection without an adjacent interfering cubic reflection. This

Jan 1, 1961

By G. R. Fritterer

Investigators in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial temperatures; i. e., 1000 to 1800 C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree. New Thermoelectric Materials A thorough survey of the literature on thermoelectricity revealed that present-day thermocouples could not meet the specifications mentioned above because their thermoelements are metallic. Metals have a marked tendency to deteriorate chemically and their melting points limit their use to low temperatures. Refractory substances, however, are usually resistant to chemical attack and are quite stable at high temperatures. Hence a survey of refractory substances having thermoelectric possibilities was made. One class of thermocouples considered was that in which carbon and a carbide of some metal or nonmetal were the thermoelements. Previous investigators neglected to study this field but certain recommendations were made by them for the use of couples in which carbon served as one element. These proposals are listed in Table 1. The couples suggested are unsatisfactory because of their low thermoelectric powers, the low melting points of their metallic elements, etc. The

Jan 1, 1933

By Louis A. Panek

THE purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fentress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal field exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The maximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repIesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: [Safe R = (rl 47r2n2r _ 7r2n2r~r~ \4/ gg in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sect.]

Jan 1, 1947

Dues: Arrears........................................... $ 4.878.18 Current........................................... 96.174.46 New Members..................................... 6.281.50 Dues for future periods received in advance........... 1.745.28 $109.079.42 Initiation Fees.................................................. 7,879.00 Magazine Receipts: Advertising Gross Receipts.......................... $39,247.77 Magazine Sales.................................... 3,820.04 43.067.81 Sale of Transactions Volumes 75 and 76............; .... $ 2,525.93 Sale of Transactions and Special Editions............... 7,586.00 Sale of Year Book.................................... 141.60 Sale of Authors' Reprints............................. 2,032.97 Sale of Pamphlets.................................... 1,346.29 Sale of Bindings...................................... 4,551.90 18,184.69 Interest Received: On Bank Balance and Temporary Investments......... $ 2,780.75 On Life Membership Fund.......................... 2,106.43 On James Douglas Library Fund..................... 5,399.45 On General Reserve Fund........................... 1,995.33 12.381.96 Miscellaneous Receipts........................................... 131.16 Total Receipts................................................ $190,624.04

Jan 1, 1929

Discussion of the paper of F. C. NEWTON, presented at the New York meeting, Feb-ruary, 1915, and printed in Bulletin No. 9S, February, 1915, pp. 473 to 477. H. 0. HOFMAN, Boston, Mass.-The results of these large-scale experiments, which were carried on at Perth Amboy, show that there are many differences between theoretical conceptions and their applications to work on a large scale. The author has given reasons why the results of bringing a desilverizing kettle to the high melting point of the zinc-silver alloy, Zn3Ag2, melting at 665° C., are not satisfactory. In all probability the alloy is dissolved in the lead; it may also be decomposed by the lead; the practical result is that this high temperature does not work. It remains now for the laboratory man to carry on systematic experiments

Jan 5, 1915

Weston Portable Electrodynamometer The Weston Electrical Instrument Co. of Newark, N. J., believes that problems hitherto considered impossible of solution in the designing of portable electrodynamometers have been solved in its new models. The voltmeter, Model 341, is an instrument' of precision adapted to use on alterating- or direct-current circuits, guaranteed to an accuracy of 0.25 per cent. full-scale value either on direct or alternating-current circuits of any frequency to 133 cycles per second and commercial frequencies even as high as 500 cycles per second with very slight error. The polyphase electrodynamometer, Model 329, is accurate to 0.5 per cent. under the same conditions.; Double ranges are furnished in all instruments of this model. All current ranges can be used for 100 per cent. overload indefinitely without introducing error in Models 310 and 329.

Jan 12, 1915

By André G. Journel

Geological study of the Prony Nilaterite (New Caledonia) began in 1969 and included drilling, geological mapping and laboratory studies. The deposit is the product of weathering of basic rocks. From top to bottom, the following zones can be distinguished: a compact ferruginous cover; ore associated with yellow laterite, containing 1.0-1.5% Ni and low in impurities (SiO2, Mg); an intermediate silicated ore containing 1.3-2.0% Ni and higher percentages of impurities; garnierite ore much richer in nickel (2-4%) but high in SiO, and Mg contents (Mg up to 20%) ; and parent rock, largely peridotites. Distinction between types of ore is essential because the high grade ore (silicated and granierites) is penalized for its high Mg contents that demand additional acid treatment. All studies made distinguish two types of ore, laterite and silicated.

Jan 10, 1973

By A. B. Kinzel

THE year 1936 has been an eventful one in the iron and steel industry. Renewed industrial activity has brought with it many new problems. These problems have generally involved the question of increasing capacity without sacrifice of economies and quality developed in the less active previous years. The nature of the iron ore used and the effect of its porosity and other physical characteristics on the capacity of the blast furnace has been reviewed by the U. S. Bureau of Mines. The whole question of handling raw materials and methods of charging furnaces has been intensively studied, with the result that capacity has been in- creased without affecting the quality of

Jan 1, 1937

By T. A. Rickard

Do not write until you have something to say. Think first; then write. In order to be understood, you must know what you wish to say. Clear writing is the consequence of clear thinking. Therefore consider your subject well before you begin to write; ruminate on it; marshal the salient facts in your mind; saturate yourself with the ideas you wish to express and with cognate ideas; then express yourself deliberately. If you are bubbling over with your subject the words will come, but you might as well expect to sail without a breeze as hope to give life to words without the living thought. Here I may advert to the fact that among the uneducated it is a common expectation to acquire the knack of writing without taking the trouble to study the art of literature. I overheard a woman in a suburban train remark to her neighbor: "I'd like to be able to write well without stopping to think about it". She was one of many that would like to do a thing well without the trouble of thinking; but it cannot be done in respect of anything to which thought is essential. The possession of a good voice does not justify a person in expecting to sing successfully to a large audience; before singing in public one has to master the technique of singing; one has to learn first how to breathe properly, how to enunciate, and many other things. The successful singer is an artist, not a megaphone. Most of us would regard a man or a woman without any training in the art of singing as a fool or an impostor if he or she were to give a public concert, yet we do not recognize the equal foolishness and imposture of persons that write books before they have studied the technique of writing. That is why so many books are unreadable, and why many books by clever men are difficult to read. They start to write books before

Jan 1, 1931