Search Documents

By Harold E. Thomas, Samuel S. M. Chan, Nicholas Bada

The U.S. Bureau of Mines has developed a technique for locating and evaluating bedding plane cracks in mine roof by an air-injection and hot-film flow logging technique. It is ultrasensitive to cracks and is especially useful for detecting the early stage of crack development. Potential applications include: (1) correlation with roof sag measurements, (2) locating cracks for grouting, (3) comparison of mechanical and resin roof bolt effectiveness, and (4) possible delineation of the fracture zone to confirm the arch hypothesis. The required equipment is inexpensive and simple to operate.

Jan 1, 1975

By W. N. Best

(San Francisco Meeting, September, 1915) INTRODUCTION CRUDE oil attracted attention because of its excellence as a fuel for open-hearth furnaces; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hot-air furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This means a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity Baumé. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230°'F., Mexican crude oil at from 175° to 210° F., and Beaumont, Texas, oil at 142° F. Fuel oil vaporizes at 130° F.

Jan 8, 1915

By J. Chipman, N. J. Grant, B. M. Shields

The vacuum tin-fusion method of analysis for hydrogen, developed by Carney, Chipman, and Grant, has been modified to permit the analysis of the evolved gases for hydrogen by means of a thermal conductivity cell. A properly prepared sample can be analyzed in 10 min with a probable error of ±0.12 ppm. A study of various methods for storage of hydrogen samples shows that samples can be safely held in a dry ice-acetone bath as long as six days. Storage in liquid nitrogen is necessary for samples to be held one week or more. HE vacuum tin-fusion method, as developed by I- Carney, Chipman and Grant,' is the only analytical procedure which has shown promise of being fast enough for use in the control of hydrogen during steelmaking. It was felt that further simplification and faster speed of operation could be effected by the use of thermal conductivity measurements for analysis of the gases evolved in the tin-fusion method. The application of conductivity measurements to the tin-fusion method is possible because: 1—the evolved gas is essentially a mixture of hydrogen, nitrogen and carbon monoxide with a hydrogen content usually over 50 pct, 2—the evolved gas is collected at a relatively low pressure, and 3— the thermal conductivities of CO and N2 are practically identical while that of hydrogen is very much greater. The major part of this research program was devoted to the construction and calibration of a vacuum tin-fusion apparatus which analyzes the evolved gases for hydrogen by means of a thermal conductivity cell. The second phase of the problem was associated with the development of a procedure for storage of samples prior to analysis. With the rapid quenching method for hydrogen sampling,' which seems to be the most practical for steel mill use, it is necessary that the samples be stored safely during the interval between sampling and analysis if the hydrogen content of the molten metal is to be maintained in the supersaturated solid samples. The thermal conductivity bridge has been used for a number of years in the analysis of certain gas mixtures. An elementary discussion of the theory and practice of gas analysis by thermal conductivity measurements is given by Minter.3 A more comprehensive discussion of the theory and of the various measuring circuits is presented by Daynes.' A complete knowledge of the theory and properties of the thermal conductivity of gases and gaseous mixtures can be gained by a study of the standard textbooks on the kinetic theory of gases."' The existing data on the thermal conductivity of single gases are reviewed by Hawkins: that for a number of binary gas mixtures by Daynes' and Lindsay." The thermal conductivity method may be applied to the determination of the composition of a binary mixture if: 1—the thermal conductivity of the mixture varies monotonically with composition, and 2— the two gases have measurably different thermal conductivities. The greater the difference between the two gases, the greater the sensitivity of the method.10 he method is applicable to the analysis of multicomponent mixtures when all of the gases in the mixture except one have nearly the same thermal conductivity. Fortunately, the mixture of hydrogen, nitrogen, and carbon monoxide evolved by the tin-fusion analysis' falls in this latter classification. The thermal conductivities of nitrogen and carbon monoxide are practically equal; and the thermal conductivity of hydrogen is approximately seven times that of the other two. Therefore, the thermal conductivity of a gaseous mixture of hydrogen, nitrogen, and carbon monoxide at known temperature and pressure can be related directly to the percentage of hydrogen in the mixture by suitable calibration. Usually the thermal conductivity of a mixture of gases is measured at atmospheric pressure where the thermal conductivity is independent of pressure over a wide pressure range. At very low pressures (below 1 mm Hg), the thermal conductivity of gases varies with the pressure. This phenomenon has been utilized in the Pirani vacuum gage for the measurement of pressures in the range of 10" to 10-0 mm of mercury.= Very little has been published concerning the variation of thermal conductivity with pressure at intermediate pressures between 1 mm Hg and 1 atm. However, preliminary measurements indicated that the thermal conductivities did vary with pressure over the range of pressures (up to 10 mm Hg) at which gases are delivered from the vacuum pump. Therefore, the calibration of the thermal conductivity cell had to be planned to include the effects of both gas composition and pressure. Such a calibration chart is shown in Fig. 4. Most industrial applications of the thermal conductivity method of gas analysis have used a compensated Wheatstone bridge circuit containing two

Jan 1, 1954

By B. F. Oliver

A levitation zone melter is described which has the necessary characteristics for processing metals of controlled purity. No crucible is required; control of the solidification variables is stable; the environment of the charge is chenzically controlled. Rotation of the solidifying interface and mixing in the liquid by the magnetohydrodynamic stirring produce an eight-fold increase in freezing velocity over former melting units with better resulting solute redistributions. The smooth appearance of processed specimens, resistivity ratios as a hnction of position, as well as a segregation curve, are presented as evidence of smooth continuous solute fransport over distances in excess of ten zone lengths. THE difficulties of the floating zone-purification of higher density metals in large quantities under conditions of lowered surface tension are well known and have hindered fundamental research programs for some time. The inordinate amount of time required to obtain a small reproducible yield of high-quality metal has excluded the use of such material for many important material research programs. However, with the use of controllable induction levitation forces' to accomplish stable liquid zones with nearly flat solidifying interfaces, and with good physical and chemical control of the processes involved, these difficulties can be overcome. A zone melter that is to be used for both high-purity and controlled composition work in metal systems must have the following three characteristics: 1) The process must avoid the use of containers. 2) Physical control of the solid-liquid interface and of the mixing within the liquid phase must be stable. 3) The chemical environment of the melt chamber must be controllable. A description of an apparatus that accomplishes these objectives follows.* APPARATUS One of the basic features that is necessary for good process control of large sections is that the charge, the coil, and the motion mechanisms be within the same chamber. This arrangement permits a close coupling between the work coil and the load, which then provides a good flexibility for adjustments of coil dimensions, for controlling the amount of levitation needed for stable operation at a given power level. An overall view of the melter is shown, with the melt-chamber door open, in Fig. 1. The radiation shields surrounding the single-turn induction coil are of water-cooled copper. The chamber is stainless steel, as are most of the components within the chamber. The control panel for the scanner is located at the immediate lower right of the melt chamber. This panel controls the operation of the scanner. The operations controlled are the interface rotation rate, the stretch-squeeze or diameter control, the up and down scanning speeds, and the induction power. All of the drive motors are constant-torque variable-speed motors. The scanning speeds are set with precision helipots and continuously observed with the voltmeter on the control panel and checked with a mechanical indicator within the melt chamber. The rotation rate is also set with a precision helipot. The up-scanning speeds are 2 to 300 in. per hr.

Jan 1, 1963

By F. C. Pittman, D. W. Harriman, J. C. St. John

This paper mentions briefly the history of hydraulic jetting as applied to perforating and fracture initiation. It points out the advantages of hydraulic perforation and undercutting as an aid for creating a fracture at the point desired rather than depending upon the weakest point in the formation for breakdown. It describes early experimental work with jet nozzles in search of better nozzle materials. The effect of splash-back damage and its subsequent influence on jet body and tool design during this work is discussed. A series of cutting-rate curves for jets cutting steel and steel-cement-formation combinations is presented to show the effect of hydrostatic head and the point of diminishing returns with respect to cutting time. There is a series of photographs showing various types of rock formation in which perforation and undercutting tests were made. These stones were drilled and the casing cemented in place as in an actual well. The casing was perforated and circularly cut as if preparing for a fracturing job. The conclusion reached in the paper is that hydraulic jetting with sand-laden fluid can be used for perforating and undercutting casing, cement and formation rock for the intended purpose of inducing the formation to fracture at a desired point. INTRODUCTION Hydraulic jetting as a means of cleaning a formation during acidizing has been used for many years. The acid-jet gun was used to clean formation and for drilling cement from casing with acid. This tool was dropped to a seating ring installed on the tubing and could be retrieved by reverse circulation or wire line. In this process, the fluids were directed against the formation to clean and penetrate beyond the mud-damaged area. After the development of the hydraulic fracturing process, interest in jetting the formation with abrasive-laden fluid was renewed. The cutting action of abrasive fluid on pumping equipment, which is a well known problem, has been utilized to perforate and undercut casing, tubing and formation. In this process, surface areas are provided in the formation on which the frac- turing pressures may work to produce a fracture at the location desired. EQUIPMENT The tools used consist of bodies containing two, three or four jets in a single horizontal plane equally spaced around the circumference. The body is threaded to the end of a string of tubing and run into the well. In addition, an expendable tool is available that may be left in the hole after perforating and produced through until necessary to remove the tubing. The bottom of each tool is equipped with a ball-type back-pressure valve. The ball can be reversed to the surface and recovered. This allows reverse circulation so that loose sand which accumulated below the tool while jetting may be removed before the fracturing job. The present jetting tools are of such length that, when screwed together, the jets fall on 12-in. spacing. ANALYSIS OF THE PROBLEM Early work with nozzles indicated that hardened steel was not a suitable material for jets and that more durable material would be required. Ceramics were tried and found to be superior to steel but still too shortlived for most applications. Tungsten carbide, which was tried and found to be the best material available, is now being used for jet nozzles. Analysis of the problems presented by this process indicated that the following information was needed. 1. The effect of submergence on a jet stream and the effect of submergence on the cutting rate of a jet stream. 2. The cutting rate and depth of a jet stream in steel. 3. The cutting rate in various formations and point of diminishing returns. 4. Size of hole or slot cut in a pipe by a given jet. 5. Fluids and sands used. 6. The flow of various weight fluids through the jet nozzle and the discharge coefficients. 7. The type cut formed in the formation by the jet stream. 8. The stretch and contraction of tubing due to temperature and pressure. The cutting effect of a jet stream on a target in the atmosphere is rapid and spectacular as most of the

By O. C. Wheeler

Production in Colombia attained a new high during 1940 when it reached a total of 25,607,976 bbl. Of this amount, the Tropical Oil Co. produced 21;426,492 bbl., including 268,586 bbl. of petroleum condensate, and the Cololmbian Petroleum Co. produced 4,181,484 bbl. from its Barco property. The wildcatting program of different companies in the Magdalena Valley that was initiated during the previous year was continued but with results that were decidedly disappointing. Ten wells were drilled in the Magdalena Valley between the approximate latitudes of Puerto Wilches and Puerto Berrio and nine of these were dry; the tenth was a small producer of no commercial importance. The prospects of finding new fields in the Magdalena Valley thus received a serious setback, since some of the tests drilled were on well developed surface structures. The prospects of the Valley, however, have by no means been exhausted and drilling operations are being continued on other prospects. One additional wildcat was drilled outside the Magdalena Valley on the Colombian Petroleum Company's Barco Concession, which brought to 11 the total number of wildcats drilled in Colom-bia during the year. This well, known as

Jan 1, 1941

By O. C. Wheeler

Production in Colombia attained a new high during 1940 when it reached a total of 25,607,976 bbl. Of this amount, the Tropical Oil Co. produced 21;426,492 bbl., including 268,586 bbl. of petroleum condensate, and the Cololmbian Petroleum Co. produced 4,181,484 bbl. from its Barco property. The wildcatting program of different companies in the Magdalena Valley that was initiated during the previous year was continued but with results that were decidedly disappointing. Ten wells were drilled in the Magdalena Valley between the approximate latitudes of Puerto Wilches and Puerto Berrio and nine of these were dry; the tenth was a small producer of no commercial importance. The prospects of finding new fields in the Magdalena Valley thus received a serious setback, since some of the tests drilled were on well developed surface structures. The prospects of the Valley, however, have by no means been exhausted and drilling operations are being continued on other prospects. One additional wildcat was drilled outside the Magdalena Valley on the Colombian Petroleum Company's Barco Concession, which brought to 11 the total number of wildcats drilled in Colom-bia during the year. This well, known as

Jan 1, 1941

By G. M. Schwartz, G. A. Thiel

THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snelling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipestone and elsewhere in southwestern Minnesota: The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation, in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowled and by Thiel and Dutton.2 The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.3 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on' the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1-Central Minnesota in the region of the city of St. Cloud, 2-the upper Minnesota River valley region, 3-the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in. their dis-

Jan 1, 1952

By A. Kaufman

More than 3 trillion gal of water are used annually by the mineral industry. Of this, approximately 21/2 trillion gal are recirculated, the rest constituting intake water. The major users are natural gas processing plants and phosphate rock, sand and gravel, and iron ore producers. Water was used by the mineral industry for mining (6%), processing (64%), cooling and condensing (27%), and miscellaneous uses such as boiler feed and sanitary purposes (3%). Whereas total water use is dependent on the quantity of material processed and on the particular process requirements of an industry, recirculation is dependent on processing, as well as cooling and condensing requirements, quality of new water intake, and the necessity for treating new and discharged water. Consumed water, on the other hand, is dependent on the quantity of water recirculated, and temperature and humidity in the area. Based on this analysis, an increase in water use by the mineral industry of 21/2 times by 1985 is forecast. Wster intake, however, will only rise 62%, because of a substantial increase in recirculation. In one report of a special series concerning the water resources of the United States, the Senate Select Committee on National Water Resources, 87th Congress, estimated that water demand would double by 1980 and triple by 2000.' In view of the possible water deficiencies that might result from such expanded usage and the need for research guidance, the Bureau of Mines organized and carried out a statistical canvass of water use in the mineral industry for calendar year 1962. The data used in this paper, unless otherwise noted, are derived from that canvass.' The efforts in this paper are devoted toward summarization of the canvass and analysis of the data. SOME DEFINITIONS Intake: Water introduced from an external source for the first time into a given mine or plant regardless of quality. Intake water is also called new water, water withdrawn, or makeup water. Fresh Water: Water suitable for cooking and drinking. Saline Water: Water containing more than 1000 parts per million of dissolved solids. Contaminated Water: Water not suitable for domestic use, but excluding saline water. Recirculated Water: Water reused to conserve intake water. Solutions that are recycled primarily because of fixed metallurgical practices, such as copper leaching solutions containing sulfuric acid, are excluded. Gross Water Used: Recirculated water plus intake water. Also called total water used. Consumed Water: Water that is lost by evaporation, as well as water lost in product. Seepage and transferred water are not considered consumed. The use of either intake or recirculated water may result in consumption. However, because of difficulties in measuring consulmption, consumed water is defined as the residual between intake and water discharged from the mine or plant. Mineral Industry: For the purposes of this paper, mineral industry includes all metal and nonmetal surface and underground mines and their associated processing plants, as well as custom mills, coal washing plants and associated mines, petroleum and natural gas well drillers, natural gas processing plants, and secondary recovery operations. WATER USE IN THE MINERAL INDUSTRY Water used by the mineral industry constitutes a relatively minor fraction of the water withdrawn by all users. Data compiled by the U.S. Geological Survey in 1960 indicate that water withdrawals, exclusive of that used to generate hydropower, approximate 99 trillion gal annually.3 Our data indicate that water withdrawals by the mineral industry comprise only 1% of this total, or 2% of the water withdrawn by industrial users. Use by Industry: Water used by various mineral industries is shown in Table I. The table indicates that close to one-half of the gross water used by the mineral industry in 1962 was used by natural gas processing plants, followed by sand and gravel, phosphate rock, and iron ore producers. The largest aggregate users of water are also the largest users per dollar of product. For example, Fig. 1 shows that the natural gas processing and phosphate rock industries are very large users of water per dollar of product. Their recirculation per

Jan 1, 1968

By W. A. Bruce

This paper covers the theory and present state of development of an apparatus for the nonmathematical analysis of complex problems of reservoir and well behavior. At the present stage of development of this apparatus, it is capable of solving the water-drive problem of any reservoir performance for which a mathematical solution has been presented in the literature, either on the basis of steady or unsteady-state flow analysis. The theory is presented for the extension of the scope of this analyzer along the lines of the present development. The resulting apparatus should be able to solve reservoir-performance problems previously thought too difficult for practical solution by mathematical means. As an illustration of its operation and present scope, the analysis of a reservoir problem and synthesis of expected performance is presented. Introduction In this method† of analyzing problems of petroleum-reservoir and well behavior, the porous continuum of the reservoir is assumed to be divided into small blocks, or units. Each block is assumed to be small enough so that for a material balance on the fluids in the block an average pressure for the block can be used. In analyzing reservoir behavior from this point of view by mathematical means, a set of simultaneous difference equations would be obtained (two for each block), which must be solved or combined into a partial differential equation. In the method to be described here, instead of solving these sets of equations analytically, electrical units are constructed, which will behave in respect to the flow of electricity exactly as the reservoir units behave under various conditions of fluid flow. The electrical units are then wired together in the same way that the reservoir units are connected naturally by virtue of their geometrical locations and shapes. Fluid-Flow Equations Consider a block in a reservoir. Assume that reservoir fluid (or fluids) is flowing in at one face and out at the opposite face, and that the block is small enough so that at all points the stream lines are within one degree of perpendicular to the face. Furthermore, assume that the pressure, pi, at the upstream face (Fig, I) is not more than one per cent greater than P2 the pressure at the downstream face. A material balance will show that the mass of fluid flowing out less the mass of fluid flowing in will equal the change in density times the fluid volume. This is expressed in the equation:

Jan 1, 1943

By W. A. Bruce

This paper covers the theory and present state of development of an apparatus for the nonmathematical analysis of complex problems of reservoir and well behavior. At the present stage of development of this apparatus, it is capable of solving the water-drive problem of any reservoir performance for which a mathematical solution has been presented in the literature, either on the basis of steady or unsteady-state flow analysis. The theory is presented for the extension of the scope of this analyzer along the lines of the present development. The resulting apparatus should be able to solve reservoir-performance problems previously thought too difficult for practical solution by mathematical means. As an illustration of its operation and present scope, the analysis of a reservoir problem and synthesis of expected performance is presented. Introduction In this method† of analyzing problems of petroleum-reservoir and well behavior, the porous continuum of the reservoir is assumed to be divided into small blocks, or units. Each block is assumed to be small enough so that for a material balance on the fluids in the block an average pressure for the block can be used. In analyzing reservoir behavior from this point of view by mathematical means, a set of simultaneous difference equations would be obtained (two for each block), which must be solved or combined into a partial differential equation. In the method to be described here, instead of solving these sets of equations analytically, electrical units are constructed, which will behave in respect to the flow of electricity exactly as the reservoir units behave under various conditions of fluid flow. The electrical units are then wired together in the same way that the reservoir units are connected naturally by virtue of their geometrical locations and shapes. Fluid-Flow Equations Consider a block in a reservoir. Assume that reservoir fluid (or fluids) is flowing in at one face and out at the opposite face, and that the block is small enough so that at all points the stream lines are within one degree of perpendicular to the face. Furthermore, assume that the pressure, pi, at the upstream face (Fig, I) is not more than one per cent greater than P2 the pressure at the downstream face. A material balance will show that the mass of fluid flowing out less the mass of fluid flowing in will equal the change in density times the fluid volume. This is expressed in the equation:

Jan 1, 1943

By Harlowe Hardinge

THE sound made by ball, pebble and rod mills has long been used by the operator as the "telltale" of their operation. The nature of this sound depends upon local conditions and the type of mill used. By experience an operator can tell whether the mill is running properly or not. Some operators are able to detect the difference in sound much better than others and get better results running the same mill tinder the same conditions. The automatic operation of a mill using sound as the fundamental means for maintaining control presents many problems. The satisfactory solution of these problems requires, for given operating conditions, a greater average output, with improved product for subsequent processing, than can be obtained by manual control.

Jan 1, 1939

By N. L. Hancox

Previous researchers have used the cutting and rejoining model to represent a porous body when attempting to place Archie's law on a theoretical basis and calculate rock permeabilities (F = Ø-m, where F = formation factor, = - porosity and m = a constant). In using the model, a porous solid is assumed to consist of sections with parallel sides containing straight. continuous pores of total porosity 4 (pore to total volume or, for a homogeneous body, pore to total area). The joining of pores at an interface between two sections is assumed to be random which results in a common pore area Ø2. This reduced area Ø2 is then taken as that area which limits electrical conduction or fluid flow in the body. Agreement between experimental results and results calculated using a model is not always good Because of this, various modifications of the model are presented — for instance, the random nature of the joining is questioned. Formation factor measurements on specially constructed porous specimens are described in this paper. it is concluded that the common pore area limits flow completely only if sections containing straight pores are very thin, and that, in most natural materials, the common pore area at an interface must be greater than that given by random joining. However, the model is still useful in permeability calculations, provided that the fractional area limiting flow is determined from formation factor measurements. INTRODUCTION Two important properties of porous media are permeability k, which describes the ease with which a fluid can flow through a porous medium, and formation factor F, defined as the ratio of the resistivity of a saturated specimen to the resistivity of the saturating liquid which describes the electrical properties of the saturated material. k is defined by Darcy's law,l k= µqL/P Ae . . . . . . . . . . . . . . . [1] where µ = liquid viscosity, q = flow rate, L = length of specimen, p = pressure across the specimen and = - the effective area over which flow occurs, F is given experimentally by Archie's law,2 F = Ø-m ,..............(2) where 4 is porosity defined as the pore to total volume or, for a homogeneous body, the pore to total area; and m lies between 1.3 for loose sand and 2 for cemented sand. Consider a porous body of total cross-sectional area A and length L, saturated with a liquid of resistivity R and with an effective area for conduction of Ae. Then, from the definition of F given previously, F=A/Ae , ................(3) or, from Eqs. 2 and 3, Ae = A Øm ..............(4) Thus, in any attempt to calculate k or F, some assumptions must be made concerning the pore structure of the body and a value derived for A,. To determine Ae, Childs and George3 and Wyllie and Gardner4 suggested an elementary statistical representation often referred to as the cutting and rejoining model of a porous body. The body is assumed to be composed of two or more parallel-sided sections of porosity 4, containing straight, continuous pores with a common pore area of Ø2 at an interface between two sections. The value is given by a random joining of the pores in either section. Two such sections,

Jan 1, 1969

By Henry A. Stiff, and Lawrence E. Davis

The authors previously presented a method for predicting the tendency of oil field waters to deposit calcium sulfate. The present paper gives a similar method for calcium carbonate. Methods for predicting calcium carbonate scaling tendencies in fresh waters have been available for some time, but these could not be used for brines. By experimentally deriving the value of the K term in the Langelier equation, a method has been developed which applies to waters of high salt content. A statistical study is included which shows that the experimentally derived values of K are in good agreement with actual conditions. Several applications of the final equation to production practice are given. INTRODUCTION The authors previously presented a method for predicting the formation of calcium sulfate scale in oil field waters.' Although calcium sulfate deposition is important in production operations, the majority of scale problems involve calcium carbonate. The present communication discusses a method by which the formation of this type of scale in oil field waters can be predicted. Calcium carbonate precipitation is caused by a shift toward carbonate in the carbonate-bicarbonate-carbon dioxide equilibrium. When equilibrium shifts in the other direction, the precipitate goes back into solution. Since there is usually considerable delay between the establishment of an equilibrium and the precipitation or solution of calcium carbonate, unstable conditions exist in which a water will precipitate or dissolve calcium carbonate on standing. Tillmans? who did a major part of the early work on carbonate scaling, pointed out that the condition of equilibrium not only indicates the tendency of a water to scale but also is an indication of its corrosive properties. Previously precipitated calcium carbonate combines with iron to form a dense crust which inhibits corrosion. If the water tends to dissolve carbonate, the scale becomes porous, and electrolytic corrosion takes place. Tillmans1 work was extended by several investigators until in 1934 Langeliers developed an equation setting forth the conditions of carbonate equilibrium. By the use of this equation the pH of a water at equilibrium can be calculated. If the actual pH is higher than the calculated pH, the water has a tendency to form scale. If it is lower. the water has a tendency to be corrosive. Langelier's equation can be expressed in a simple form as follows: SI = pH-pCa-pA lk-K where: SI is the stability index. A positive index indicates scale formation. A negative index indicates corrosion. pH is the pH of the water sample, as actually determined. pCa is the negative logarithm of the calcium concentration. pAlk is the negative logarithm of the total alkalinity. K is a constant, the value of which depends on the total salt concentration and the temperature. This equation has been shown to apply to waters with totaI solid concentrations as high as 4.000 ppm. In fact, control of fresh water treatment by means of this equation has been standard text-book practice for a number of years. Nomographs have been worked out so that the stability index of a fresh water sample can be determined in a matter of minutes. Most oil field waters, however, contain well over 4,000 ppm of salts and for this reason the usual application of Langelier's equation can not be made. By an empirical method we have extended the application of the Langelier equation to waters of high salt concentration. By the use of this equation the tendency of oil field waters to deposit calcium carbonate can be predicted.

Jan 1, 1952

By Bjorn N. P. Paulsson

A number of granitic rock specimens have been studied from the Stripa mine site in connection with a large-scale geomechanics research program. The purpose of the program was to evaluate and develop field and laboratory techniques for rock mass characterization and to determine design parameters for storage of nuclear waste. In this paper a minicomputer-based technique for studying dynamic rock properties in the laboratory is described, together with results from the tests. The specimens were tested under different uniaxial and saturation conditions. Specimens from a field-heated rock mass were also tested to determine if temperatures typical of those encountered with nuclear waste would introduce additional fracturing. Both Vp and Vs increased with stress for both saturated and dry specimens. Both Vp and Vs were higher for saturated specimens at all stress levels compared with the dry. The velocities increased linearly or near linearly with saturation. The test results on the previously heated samples indicate that attenuation is more sensitive to thermally-induced microfracturing than velocities. Analysis of the attenuation values with stress show that rock heated to 200°C is damaged, and that the damage is in form of low-aspect ratio fractures.

Jan 1, 1984

By R. T. Mishler

I wish to express my keen appreciation of the article on the above subject by Coe and C1evenger.l It has been doubly interesting to me, for the reason that the experience recorded and the principles evolved practically parallel the results of similar investigations made by myself and others at The Lucky Tiger Mine, El Tigre, Sonora, Mex. An outline of the work at El Tigre may aid in confirming the principles expressed by Coe and Clevenger. El Tigre has the unenviable distinction of possessing a slime with a much lower settling rate than any recorded in the article discussed. Under most favorable conditions the settling rate is about one-third that reported for the Liberty Bell mill, and one-tenth that reported for the Nipissing, Golden Cycle, and Presidio mills. This slow settling characteristic of Tigre ore has necessitated careful investigation of settling phenomena throughout the various evolutions of the plant. Previous Settling Investigation at Tigre During construction work at the mill, the metallurgical engineer in charge, D. L. H. Forbes, ran a series of experiments on settling. His tests proved that deep settling tanks were not ordinarily necessary. The use of tanks 2 or 3 ft. in depth was suggested.2 Later experiments demonstrated that the following principles of settling applied to Tigre pulp.3 1. In settling dilute pulp, settling rates are independent of pulp depth. 2. In settling thick pulp, settling rates are approximately proportional to pulp depth.4

Jan 1, 1918

By L. J. Howell, A. S. Roy, H. H. Kellogg

KNOWLEDGE of the phase diagram of salt systems is important for selection of the optimum con- ditions for electro winning of the refractory metals from fused salts. This note summarizes the studies of the NaC1-rich portion (0 to 22 mol pct HfC14) of the NaC1-HfC14 phase diagram. Melts in this composition range have vapor pressures well below one atmosphere and melting points between 548° and

Jan 1, 1959

By E. C. Simmons

Uranium is an incompatible element with respect to the major rock-forming minerals crystallizing from granitic magma, entering instead trace minerals such as zircon. The relationship between the saturation limit (SL) for such a mineral and the bulk distribution coefficient (Do) for U is central to understanding the distribution of U and its availability to late-stage fluids that can form ore deposits directly, or labile U that can be remobilized later. Low SL values imply early crystallization of zircon, but in very small proportions, minimizing Do and maximizing the degree of enrichment of U in late-stage fluids. Thus, granitic rocks with low Zr contents (due to a low saturation limit for zircon) are most likely to evolve U-enriched differentiates; this will be reflected in a high U content of the zircons (but not necessarily high U abundances in whole-rocks). Thus, the ratio of the U content of zircon to the Zr content of the corresponding whole-rock is potentially a very useful parameter in identifying granitic rocks most likely to have U-enriched solutions associated with them. The granitic rocks associated with the U deposits of the Midnite mine area, Washington, have geochemical characteristics that fit the model presented very well. The rocks are very low in Zr (100 ppm) and contain zircons with extremely high U contents (3,000-4,000 ppm).

Jan 1, 1984

By J. D. Edwards

When Charles Martin Hall invented the electrolytic process for the production of aluminum, one basic requirement was a supply of pure alumina. Now, more than 50 years later, the same requirement still holds, and there are no technical straws in the wind to indicate that this situation is likely to change. Long ago, Aluminum Company of America took a number of steps to see that this country should not face shortages of alumina and aluminum in time of emergency. As one step to this end, the Company developed and used a supply of bauxite in South America in order to conserve dwindling Arkansas reserves. Another, and more a program than a step, was to investigate every type of process that might bear the possibility of utilizing the low-grade ores of aluminum that are more plentiful than bauxite. It is a long story, but the investigation included electric-furnace processes, acid extraction processes and alkaline extraction processes, with or without preliminary furnace and sinter treatments. Some of the processes developed were operated in commercial production. This work has been continuous since the first World War. The turn of the wheel came sooner than was expected when, in 1942, bauxite shipmerits through the caribbean became uncertain and hazardous through the operation of submarines. The tremendous requirements of aluminum for the war effort were consuming high-grade bauxite at an alarming rate and a national search for substitutes began. High-grade bauxites, for technical and economic reasons, have been defined as those containing about 7 per cent or less of silica. While bauxite of this grade was limited in amount in the United States, there was in sight a substantially greater volume of low-grade, high-silica bauxite not amenable to economic treatment by the Bayer process, but richer in alumina than the clays or other available low-grade ores. It was at this point, and after several years of intensive research on this particular phase of the problem, that Aluminum Research Laboratories brought to completion the invention of one of its research staff, which made practical the utilization of large reserves of low-grade bauxite in America. Bayer Process The Bayer process has been almost universally used for the production of alumina from bauxite. This process, in outline, comprises the digestion of hely ground bauxite in a solution of caustic soda (NaOH) under pressure and at an elevated temperature. Alumina in the bauxite goes into solution as sodium alumi-"ate and the impurities—oxides of iron, titanium and silicon—remain undissolved. The undissolved residue, known as "red mud,'' from its color, is separated and run to waste. AluKlinum hydrate (A12O3.3H2O) is precipitated from the solution of sodium aluminate, and the liquor containing the caustic soda and some alumina is returned to the Process for digesting more bauxite. The aluminum hydrate, after washing, is calcined at a high temperature to produce

Jan 1, 1949

By Nathaniel Herz

The formula very frequently used for computing the economical size of pipe to transmit compressed air is that of D'Arey, as follows: D = cV w1l Where, D = the volume of compressed air delivered in cubic feet per minute, at the final pressure. c = an experimental coefficient determined for the various sizes of pipe, d = the diameter of the pipe in inches. 1 = the length of the pipe in feet. p, = the initial gauge-pressure in pounds per square inch, p2 = the final gauge-preesure in pounds per square inch. w1 = the density of the air, or the weight in pounds per cubic foot at the initial pressure, p1. The most common case is that in which the given quantities are: the quantity of air required, the length of the pipe, and the initial pressure. The method of solution is to assume a pressure-loss and to compute the remaining factor, cd5, thus giving the size of pipe corresponding to the assumed loss of pressure. It is always desirable to try two or more pressure-drops, in order to find the combination that is most satisfactory, since often a small change in the size of pipe will reduce or increase the loss of pressure several pounds. An alternative method is to assume a size of pipe and calculate the corresponding pressure-drop. Each method involves a series of tedious calculations to arrive at the most economical solution, and also requires the use of tables giving the constant, c, the density of the air, w1, and often, for convenience, a table giving the values of the expressions p1-p2 and c J I hare constructed a graphic chart, Fig. 1, for the solution of

Jan 1, 1913