Search Documents

By Charles H. Thurman

THE data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. DRAGLINE VS. BUCKET-LINE Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 10¢ gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new, 7-cu. ft. bucket-line dredge, costing upward of $250,000, and with operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These percentages of operating time are important factors in making a comparison of this kind. The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft. (65 ft. below water, 15 ft. above). A 5-cu. yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10¢ gravel 28 ft. deep with bucket line, costing 4¢ per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equipment, fully depreciated. Dismantling, mov-

Jan 1, 1945

By Charles H. Thurman

The data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. Dragline vs. Bucket-line Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 106 gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new 7-cu. ft, bucket-line dredge, costing upward of $250,000, and in operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ Per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These Percentages of operating time are important factors in making a comparison of this kind- The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft- (65 ft. below water, 15 ft. above). A 5-cu. Yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10 gravel 28 ft. deep with bucket line, costin 4¢ Per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ Per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equip-ment, fully depreciated. Dismantling, mov-

Jan 1, 1946

By Chas. A. R. Lambly

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. Geology The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varying low dips in varying directions, and underlie large areas of the district. History Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that suficient tonnage existed to justify a redesigning of the whole operation, surface and underground. After four years of general study, the following program was planned: 1. A new mine entrance, which would be an incline, that could follow the ore body down at whatever pitch was necessary. The incline will be equipped with conveyors for the moving of ore and waste to the surface and with tractor-type locomotives for man and supply transportation. 2. The new incline also required a new type of mining which was developed and is now in use. It is called contour mining and will be described in a future paper. 3. The new incline exit would necessitate the moving of the mill and mine shops across the Pend Oreille River. This part of the program is now underway. The Incline The sinking of the incline was to start as soon as World War II ended and was as follows: The first leg of the incline was to be sunk from the surface 1600 ft on a 17" slope. The collar and first level at elevation 2180 ft, the second level at elevation 2000 ft, the third level at elevation 1875 ft, and the fourth level at elevation 1700 feet. From the 1700 ft elevation the incline was to flatten out to 12" for 400 ft to give the necessary depth for the ore pockets below the 1700 ft level and the necessary clearance for future sinking (see Fig 1 and 2). Due to lack of manpower in 1946, the program was changed and was as follows: A drift was driven from the old mine workings on the 1700 ft elevation in an easterly direction. At 1300 ft the drift was turned N 50" E and at this point a raise was driven 180 ft on a 50" slope. This raise intersected the Josephine horizon and commercial ore was encountered. At the 2000 ft mark, a main raise was driven, 245 ft on a 50" slope, and the 1875 ft elevation was cut. Exploration drifts were started on this level and production followed on a limited basis. The main drift at the 2500 ft point was turned N 35" E and ran parallel to and 10 ft east of and under the proposed incline line. At the proposed intersection of the drift and incline on the 1700 ft elevation, it was planned to raise the incline to intersect the 245 ft raise and to continue on to the surface, a distance of 1600 ft. When this proposed intersection point was reached, a heavy flow of water, approximately 800 gpm, was encountered and all work on the main drift face was stopped. This water flow flooded the main pump station in the old mine and the two lower levels with approximately 20,000,000 gal of water. The water was controlled and finally drained from the cave areas and lower levels after six months of pumping. After the heavy flow of water was encountered in the main heading, it was decided that the incline would have to be started from the surface, as originally planned, so that too much time would not be lost. The surface overburden had to be removed, a total of 6000 yards. A temporary dry house for 6 men was built. An 8 in. churn drill hole was intersected in the first raise driven from the 1700 foot elevation tunnel. Air and water lines were placed in this hole, and air and water were delivered to the collar of the incline from the mine working. The incline started down at 15 ft wide and 7 ft high through the Leadbetter slates. After sinking 4 sets, it was

Jan 1, 1950

By J. J. Arps

n approach to the study of the electrical properlies of drilling muds, their cakes and their filtrates was made by treating the drilling fluid as a porous medium. Lluring this study it was found that the weight pararneter was omitted from previous investigations on electrical properties. Patnode in 1949 made a similar approach to ,his investigation. His work showed that there was a variation of resistivity relationships with per cent Puid present in a given suspension. This present study ex-tends Patnode's investigation to one in terms of the solids fraction of the drilling fluids. Previous investigations were made on low weight muds where the effect of the rolids fraction was obscured. The following equationr were fitted to data taken from 94 field muds and 47 laboratory muds (see Tables I and 2). The parameter, C, is a complex function of the solidr content, or mud weight, of a drilling fluid. It was also found that for all drilling muds examined. A nomograph is presented combining Eqs. I and 2. INTRODUCTION It is generally recognized that the materials present in drilling muds affect the relationship between mud filtrate and mud resistivities. However, most electric log interpretations proceed with the assumption that the mud resistivity and temperature are the only important parameters needed to obtain a filtrate resistivity or a mud cake resistivity. Lamont1 suggests that only average relationships exist between mud cake, mud filtrate and mud resistivities. He indicates that there is limited accuracy when these intercorrelated factors are used since no other measure-able variable is apparent. A previous paper by Patnode indicates that drilling fluids may be considered to be a system of fluids in solid particles which may be correlated electrically in a manner similar to rock solids. 1 he equation for the resistivity factor. F = (per cent fluid) is satisfied for a given clay type in water, but the value of m varies as different materials are used in the water. The resistivity factor is not constant for a given amount of clay. As is suspected it varies as the solids fraction conducts electrical current. Since both weighting material and clay solids are present in commonly used drilling fluids, it is expected that both materials contribute to the variation of the m factor in Eq. 3. An extension of Patnode's work is presented in this paper to show some of the interrelations which exist between the resistivities of mud cake, mud filtrate and mud. Use of these data enable a more accurate calculation of mud filtrate and mud cake resistivities if only the mud resistivity and weight are measured. EXPERIMENTAL The measurements of mud weight, fluid and solids resistivity, alkalinity, and chloride content of mud samples were made in this research. Mud samples representing drilling fluids from 94 Louisiana and Texas wells (Table 1) and 47 laboratory-constructed systems (Table 2) were used in the experimentation. The measurements of the mud properties were made both in the field and in the laboratory. The tests on the properties of weight, alkalinity and chloride ion were standard tests as described by API specifications. The resistivity measuring devices were constructed in the laboratory for this study. For details on the resistivity equipment see Fig. 1. The fluid cell

By H. D. Outmans

Present first-order theory for frontal stability and viscous fingering of immiscible liquids is improved by including the nonlinear terms in the equations describing conditions at the interface of the liquids. This leads to the revision of several conclusions which were based on first-order theory. They concern the growth rate and changing shape of a sinusoidal disturbance, particularly in relation to the wave number of this disturbance. Nonlinear aspects of effective interfacial tension are discussed and it is shown that this tension is not simply a positive proportionality constant in a linear relation between pressure difference and curvature at the interface. Scaling requirements are determined from the dimensionless groups which govern fingering. Gravity and interfacial tension invalidate a previously formulated conclusion that the shape of a finger after a given displacement is independent of the displacement velocity. Also, similarity of fingering (and, hence, of sweep efficiency in case of an unstable front) requires geometrical similarity of the initial disturbance in the model and the reservoir with a scale factor which is the same as the one for scaling down the dimensions of the reservoir. INTRODUCTION The critical velocity at which the transition zone in the vertical displacement of immiscible liquids becomes unstable was calculated by ill. More recently, the same was done for nonvertical displacements and it was also shown that the stability is affected by an effective interfacial tension between the liquids. 2-4 Although in the oil reservoir a stable front is always desirable from a recovery point of view, the necessary velocity may have to be so low that the corresponding production rate is not economical. In that case, a knowledge of the fingering unstable front is necessary for predicting recovery at break- through. Studies in this direction have not gone beyond the very moment at which fingering first occurs.5,6 Conclusions about stability and fingering in these references are all based on linear theory. In this theory the nonlinear terms in the equations describing conditions at the front are neglected. The usual justification for this lack of mathematical rigor is that the nonlinear terms can be made small relative to the linear terms and, supposedly, small causes produce only small effects. It has been recognized, however, that this is not necessarily true in the nonlinear problems of hydrodynamics.7 The hydro-dynamic stability and fingering of the front between two liquids, accelerated in a direction normal to the front, for instance, is strongly influenced by the nonlinearity of the boundary conditions.8-10 Since these boundary conditions are not unlike those arising in the problem of stability and fingering of the front during a slow immiscible displacement in porous media, it was thought that there, too, the nonlinear terms should be taken into consideration. A summary of the results obtained in linear theory and a comparison with experimental data precede the nonlinear theory developed in this paper. This summary serves to introduce some quantities which will be used in the further develop ment. It should also be pointed out that the method of higher-order approximation by which the nonlinear stability problem is solved has application in other reservoir studies.11 SUMMARY OF LINEAR THEORY 1. A plane interface remains stable if its velocity is smaller than a critical velocity. vc = (p2-p1)gn/(l/A2- l/A1 .........(1.1) This equation is derived for uniform flow in a thin layer inclined to the horizontal plane. The displacement takes place in a direction normal to the intersection of this layer and the horizontal plane. The undisturbed (line) interface is normal to the velocity. Fluid 1, the upper fluid (gas), is displacing Fluid 2 (oil). (VcQS would be the injection rate in cc/

By L. B. Underwood, C. J. Distefano

NORAD, when completed, will be housed in large chambers excavated out of the granite beneath the Cheyenne Mountain near Colorado Springs. A room and pillar layout for the chamber excavation was selected and executed. Many complex problems arose in designing a rock bolt system; this paper includes discussions on: rock strengthening following excavation, excavation and ground support problems, orienting rock bolts with respect to jointing systems, conducting pull tests, four-way chamber intersection problems, the need for grouting rock bolts, and loss of tension and permanency of anchorage in a rock bolt system. In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colo. Known briefly as NORAD, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Fig. 1). The NORAD COC, a U.S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources: radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action.'

Jan 1, 1968

By R. R. Angel

Drilling rate is a parameter that should be considered in determining the volume requirements for air and gas drilling. The use of past methods which ignore the effects of the solids content upon the pressure and velocity of the annulus flow stream can result in undercalculation of the required volurne by as much as 50 per cent. A vertical-flow equation is presented for determining volume requirements. This equation includes the effect of the solids that are transported up the annulus in the flow stream by incorporating the drilling rate as one of the parameters. The effect of down-hole temperature on required circulation rates is also ana-lvzed. A simple approximate method of determining volume requirements is presented. This method is more accurate than the methods used in the past. Hole cleaning difficulties are analyzed for a recent air drilling job where past methods indicated that - excess air was being used. Sample curves of calculated boitom-hole pressures are presented for air and gas drilling in several hole sizes. INTRODUCTION In certain areas the use of air or natural gas as a circulating medium for drilling oil and gas wells is becoming a common practice. Large increases in penetration rate and bit life are achieved through the use of these media in preference to mud or water. Drilling rates as high as 90 ft/hr have been obtained in shales. The importance of maintaining adequate circulation rate is generally recognized; however, much disagreement exists among drilling operators as to what constitutes "adequate" circulation rate. In quarry drilling, where annular velocities can be accurately determined, an annular velocity of 3,000 ft/min of standard air is required for best results in rocks having approximately the same density as those commonly penetrated in drilling oil or gas wells'. Although this standard air velocity has proven satisfactory for quarry drilling, some oil and gas well drilling operators believe that an equivalent annular velocity of more than 4,000 ft/min is required; others believe that as little as 2,000 ft/min . is sufficient. Much of this disagreement results from determining the required circulation rates with methods which fail to incorporate the drilled solids in an equation which is applicable to vertical flow. Hughes Tool Co. Bulletins No. 23' and 23-A3 present data for determining circulation rates based on the Weymouth formula. These data do not include the drilling rate as a parameter and, therefore, neglect the effect of the solids being transported up the annulus. In spite of this apparent defect and the fact that the Weymouth formula is not applicable to vertical flow, the Hughes data have well served the drilling industry in many areas and are important and timely contributions to the science of air and gas drilling. The Hughes data purposely omit a correction for increasing down-hole temperature. At slow drilling rates this effectively compensates for the use of a formula which is not valid for vertical flow; however, volumes determined by the Hughes method are not sufficient to support rapid drilling rates at moderate and great depths. For example, Phillips Petroleum Co.'s Cauthorn "D" No. l in the Vinegarone field for Val Verde County, Tex., was air drilled from 1,500 to 9,300 ft using a compressor delivering 1,400 cu ft/min. The 8 3/4-in hole was drilled with 5-in. drill pipe, and drilling rates as high as 90 ft/hr were obtained between 7,000 and 9,300 ft. No water or caving hole was encountered. At 7,728 ft it was necessary to wash-out 60 ft of cuttings to reach bottom after a trip to change bits. At 8,130 ft a twist-off occurred and the drill col-lars were stuck in drill cuttings. These difficulties indicate that the 1,400 cu ft/min of air was not sufficient to keep the hole clean. Hughes data indicates that 1,180 cu ft/min is sufficient to produce an annular ve-

Jan 1, 1958

By Alan Lawley

AS part of a programme of experimental work on single crystals of rhenium and ruthenium, it was found necessary to have the crystallographic angles for these elements. The angles given in Table I were determined to the nearest minute of arc, by Univac Computer. The angle $ between (HKIL) and (hkil) is given by the formula: The angles given for rhenium should be particularly useful in view of the increasing interest in this element. For completeness, angular values are also given for cadmium zinc and magnesium; these form a more complete set of values than those given by Salkovitz.' The assistance of Professor J. Hobstetter and Mr. J. Crozier in the programming of this data is acknowledged. The work is sponsored by the Office of Naval Research under contract No. NONR 551 (19).

Jan 1, 1961

By Axel Sahlin

Since the days of the infancy of metallurgical industries, slags of various kinds have been accumulating. Until a comparatively recent date hardly any employment had been found for these waste products, which have had, consequently, little or no value. An exception to this rule is the basic Bessemer slag, the value of which has become universally recognized. It is to-day one of the standard fertilizers of the world, and a price of from $15 to $20 a ton is considered reasoiable for the ground slag, which, especially in Germany, finds a ready market as fast as it is prepared. The slags from puddling and re-heating furnaces have only found vol. xx.—25

Jan 1, 1892

By K. A. Slagle, D. K. Smith

weight obtained. Additives used in conjunction with salt in these slurries have included silica flour, calcium ligno-sulfonate and cellulose retarders, granular lost-circulation materials, bentonite and selected low-water-loss additives that are not significantly deteriorated by the presence of the chloride ion. In some other areas of South Texas, the salt-saturated slurries have been used quite extensively for improvement of the flow properties of slurries and attainment of better circulation characteristics at lower displacement rates. Concurrently with this property, the protection of shales and shaly sands is also realized, as well as useful retardation of the slurry. Resultant superior cementing jobs have been indicated by both communication tests and acoustic logs for bonding to pipe and formation.' In one section of Louisiana, a major oil company has been using salt-saturated API Class A cement with calcium lignosulfonate retarder for cementing through the Miocene at 9,000 to 10,000 ft. This is another of the situations where interbedding of sands and shales exists, creating difficulty in maintaining formation competency when a fresh-water slurry contacts the clay minerals of the formation. Further work has also been done in the shaly Miocene formation at 13,000 to 15,000 ft where fairly close water or gas contacts are encountered. Indications thus far are that better segregation of these various fluids is obtained by use of the saturated salt slurries because of their improved formation bonding characteristics. In addition to the properties of salt in this situation, attainment of turbulent flow at minimum displacement rates has also been accomplished by use of an additive to help provide exceptional dispersion and viscosity reduction of the slurry. Another oil company was encountering considerable expense in completing wells in Southwestern Louisiana due to extensive block squeeze requirements for effective separation of zones. A very effective mud program was being used to minimize washout in the shale sections and, apparently, a nearly gauge-size hole was being obtained. However, primary cementing results with fresh-water slurries were generally poor. On a few occasions when slurry was actually circulated to the surface, large pieces of shale formation were brought out of the hole with the slurry, indicating a severely water-sensitive, sloughing formation. Inhibition of shale heaving was being accomvlished in the drilling program, and immediately indone ipon circulation of the fresh-water slurry even though it contained a low-fluid-loss additive to reduce filtrate damage in the sands. The subsequent change to salt-saturated slurry yielded 11 successful primary cement jobs out of 12, compared to the previous success ratio of practically zero. Since these were deep, high-temperature wells in the range of 13,000 ft with high-pressure zones necessitating 17.5-lb/gal fluid densities, the slurry used was API Class E cement, silica flour, weight material, retarder, salt saturation (which also reduced the amount of weight material) and maintenance of low fluid loss by use of a salt-compatible additive. Other salt slurries have been used to a limited extent in this same general area for similar problems at depths ranging from 5,000 to 17,000 ft. In the shallower wells, the cement has usually been API Class A where the salt functions as a retarder, and in the deeper wells API Class E cement is used with the additional salt advantage being its increased slurry weight and inability to dissolve salt stringers. A considerable number of squeeze jobs have also been done on older wells using the salt-saturated slurries with very good results. MID-CONTINENT In North Texas, salt-water slurries have been used for cementing the Woodbine sand, Strawn sand, KMA sand and Pettit lime. Shales surrounding these formations have created the same difficulty in obtaining separation of producing zones that has been the problem in other areas. Depths in this area range from 3,400 ft for the Strawn to 7,400 ft for the Woodbine, and concentration of salt has varied accordingly. In the deeper wells, where retardation is desired, saturated salt-water cement is used; for the shallower wells, in order to provide shorter waiting-on-cement times, the amount of salt has been 18 per cent by weight of the mixing water. Results have been excellent with no reported failures on any of the salt cement jobs; where acoustic bond logs have indicated indifferent bonds previously, they are indicating very good bonding for the salt slurries. In Oklahoma various shales of Pennsylvanian age exhibit a high degree of sloughing in the presence of fresh water, causing severe washouts above and below sand formations which it is desired to isolate. This situation exists to some degree in practically all parts of Oklahoma and includes formations of other ages such as the Wood-ford shale. For the past few years, salt-saturated cements and displacement rates as high as practical have been used as a remedy for this problem, with very good results. The Layton and Bartlesville formations are two examples of shaly sands where saturated slurries have been helpful. In one area where five wells were drilled through this type of problem shale without obtaining a satisfactory primary cement job, a change was made to salt-saturated cement preceded by a suitable chemical wash for the drilling mud involved. Acoustic bond logging indicated excellent bonding, and final completion bore out this result by being trouble-free. This type of slurry has also been used extensively on squeeze jobs where shales have been heaving around the producing formations. Predominantly, the basic slurry has been either API Class A cement or a pozzolan cement—although, as deeper wells are being drilled, the use of salt in Class E cement is also increasing. Salt cement in West Texas has been used primarily to help prevent channeling through the shales around the Delaware sand, Queens dolomite and Hope lime. Many of the shaly and dirty sands of this area are sensitive to the filtrate from a fresh-water cement. Salt at 16 to 18 per cent by weight of mixing water has been added to centent, and has been effective in controlling formation damage and communication between zones in these formations. Use of these lower salt concentrations is dictated in this area by the relatively low formation temperatures where retardation of the slurry would create unduly long waiting-on-cement times. Also, quite a bit of cementing has been done in this area using salt concentrations in the accelerating range— that is, 2 to 5 per cent by weight of water. Specifically, these concentrations have been used in coiljunction with high percentages of gel to overcome the retarding effect of the calcium lignosulfonate dispersant, although there are probably several shales where these concentrations could provide some degree of formation stability. On several occasions, the salt has also been used to lower the critical velocity or rate for turbulence with the slurry, particularly in the pozzolan cements. On wells in the Hope lime, it has usually been necessary to squeeze the shale above and below the lime to get a water-free completion. Use of salt-saturated slurries has largely eliminated this

By David A. Thomas, Eugene S. Meieran

MECHAMCAL, electrical, and other property measurements are often more easily made on wires than on sheets. In order to carry out transmission electron microscopy on the same material used for property determinations, we have developed a method for preparing thin foil specimens of wires. The technique was developed for 0.030 in. diam tungsten wires, and is a modification of the thinning techniques used by Wilsdorf, et al 1 A length of wire is first ground to about 0.010 in. thick by mounting the wire in low melting temperature wax, hand grinding a longitudinal flat, removing and reversing the wire in the mount, and then grinding a second parallel flat. The 0.030 in. wide and 0.010 in. thick strip is cut into 1/8 in. lengths to fit in the specimen holder of the electron microscope. Next the specimen is gripped in platinum-tipped tweezers (the anode) and placed 2 mm below a hol- low copper cathode with a 0.010 in. ID nozzle. Electrolyte, 10 pct NaOH, flows by gravity feed through the nozzle onto the specimen, as shown in Fig. l(a). Polishing is carried out until a shallow impression is made on one surface, and then the specimen is turned over and the opposite surface indented. The metal between the two impressions should be about half the specimen thickness, as is shown by the heavy line in the cross section in Fig. l(b). The entire specimen is then electropolishedin 2 pct NaOH until a hole appears at the location of the indentations. The apparatus is shown in Fig. 2, and is essentially the same as that used by Wilsdorf et al. at The Franklin Institute. Light is reflected by a mirror onto the bottom surface of the specimen! which is viewed by a stereoscopic microscope placed above it. Polishing is carried out until light is seen, indicating that a hole has formed, and then immediately stopped. The specimen is washed in water. alcohol, and ether, and is then ready for examination. The specimen should be reversed in its platinum clip during electropolishing to insure equal polishing on both sides of the impression. For tungsten, indenting at 120 v and 0.04 amp takes less than 1 min, and final polishing, at 10 v and 1 amp, less than 5 min. The portion of the specimen available for transmission microscopy surrounds the hole, as is seen by the dashed lines in Fig. l(b). Slight electroetch-ing accompanying electropolishing reveals the mi-crostructure, as seen in Fig. 3(a) by light microscopy. Low-magnification electron microscopy, as in Fig. 3(b), enables the same areas and grains to be viewed and identified when subsequently examined at high magnification. Fig. 4 is a typical structure of

Jan 1, 1963

By C. R. Clark, G. Swift, D. S. Roberts

The purpose of this investigation was to measure PVT behavior of various types and combinations of heavy hydrocarbon components from the paraffinic, naphthenic and aromatic classes where the relative proportions Of the various components were selected to approximate those of natural gas or gas condensate systems. Synthetic mixtures were used so that the compositions Of the various components could be measured accurately. n-Heptane, methylcyclohexane and methylbenzene were used to represent the paraffinic, naphthenic and aromatic components of the heavy fraction. In the mixtures studied, the heavy fraction composition was held constant at O. O5-mole lraction, the balance being methane except for one mixture where 0.10-mo1e fraction of an intermediate component, propane, was added. The PVT data for the mixtures were determined in a variable-volume, constant-mass apparatus at psuedo-reducedtemperatures from 1.84 to 2.00, over a pseudo-reduced pressure range from 2.3 to 12.0. The experimental results showed that, regardless of the type of heavy material (paraffinic, naphthenic, aromatic, or combinations thereof) mixed with methane or methane and propane, the compressibility factors at equal values of pseudo-reduced temperature and pressure varied by less than 2.2 percent. INTRODUCTION PVT data is used for natural gas and gas condensate fluids in determining reserves of reservoirs and performance of wells, in metering produced fluids, and in recombining samples for laboratory studies. While there are vast amounts of PVT data reported for natural gas and gas condensate systems from which useful correlations have been developed, ' the compositional analyses for these systems and the resultant correlations typically were made with components analyzed through some arbitrary carbon number, usually C6, with the residue reported as a lumped "heavy" fraction. The heavy fraction was stoichiometrically recombined on the basis of an apparent molecular weight to give the final compositional analysis. It is virtually impossible to make a systematic analysis of the effect that variation of the relative amounts of paraffinic, naphthenic and aromatic constituents of the heavy fraction of natural systems might have on PVT behavior. Because there is considerable latitude in the relative amounts of these constituents, one speaks of crudes or condensate liquids as being "paraffin base", etc. It is of interest to determine if changes in the relative amounts of these three types of hydrocarbons in the heavy fraction cause significant changes in PVT behavior. If so, steps should be taken to describe better the nature of the heavy fraction in PVT correlations. If not, more confidence can be placed in the correlations presently employed. DESIGN OF THE EXPERIMENTAL INVESTIGATION We attempted to determine if changes in the base of the heavy fraction would cause significant changes in the PVT behavior of gas or gas condensate fluids. Synthetic mixtures were used to enable us to systematically vary the base of the heavy fraction and to analyze accurately the fluids. We found that the heavy fraction of naturally occurring condensate systems seldom exceeds 0.05-mole fraction. Thus, the mole fraction of the heavy fraction in the synthetic systems studied was set arbitrarily at 0.05, to maximize whatever deviations in PVT behavior that might occur. Further, we judged that since the C7 hydrocarbons normally are present in greater quantities than higher carbon number hydrocarbons in naturally occurring systems, the use of n-heptane, methyl cyclohexane, and methylbenzene to represent the paraffinic, naphthenic, and aromatic species in the heavy fraction would be most appropriate. Finally, to enable us to compare our

Jan 1, 1970

By C. H. Frick

Before presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. Introduction The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accumulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3/16-in. round-hole screen and over a 3/32-in. or a 1/16-in. round-hole screen. Use of Smaller Sizes The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced—a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1949

By H. J. Freyn

The American iron and settl manufacturer finds himself to-day barely at the threshold of enormous possibilities for practicing rational economy in the use of fuels.

Jan 1, 1915

By J. K. Furst

THE reasons for manufacturing steel by the duplex process are, briefly: saving of time; increasing output for capital invested; and avoiding the difficulty sometimes experienced in obtaining scrap. On account of the latter reason, some plants duplex only at such times as the price and quantity of scrap in the open market warrant. At some plants the use of the duplex process enables, the blast-furnace practice to be simplified, because the furnaces run more smoothly and produce more iron when not held to a strict specification as to the silicon and phosphorus therein. The duplex process was practiced in Witkowitz as far back as 1878, but it was left to the steel makers of this country to develop it along practical, commercial lines. The American companies manufacturing steel by the duplex process at the present time are: Tennessee Coal, Iron & Railroad Co., Maryland Steel Co., Bethlehem Steel Co., Pennsylvania Steel Co.; Jones & Laughlin Steel Co., Colorado Fuel & Iron Co., Lacka-wanna Steel Co., Dominion Iron & Steel Co. of Canada. All of these companies, except the Dominion Iron & Steel Co., combine the acid Bessemer with the basic open-hearth process, while the latter combines the basic Bessemer with the basic open hearth. The Tennessee Coal, Iron & Railroad Co.'s Plant The installation of a converter of 15 tons capacity at the Ensley plant of the Tennessee Coal, Iron & Railroad Co. in 1904 marked the introduction into this country of the duplex system. The experience gained in the employment of the Bessemer converter had demonstrated that there was a shortening of .the time required in the open-hearth furnace and a reduction of the outlay for fuel and lime, thus affording substantial evidence of the economies resulting from this method.

Jan 10, 1914

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By S. G. Epstein

Electromigration has been measured in dilute liquid alloys of lead in antimony and antimony in lead. In these alloys antimony migrates with the electron current; lead migrates in the opposite direction. These results, which contradict the mass criterion, were predicted by the electron drag model for electromigration in liquid alloys. The existing experimental data are shown to correlate with the difference in electrical resistivities of the alloy components. FOR many years investigators have attempted to relate observed electromigration phenomena in liquid alloys to the physical properties of the alloy components. The most successful correlation was found by Angus et' al.,1 who in 1959 proposed an empirical criterion for predicting the relative direction of motion of the components of a liquid alloy in an electric field: the component with the smallest atomic mass concentrates at the cathode. While this criterion is obeyed in nearly all the alloy systems which had been investigated, the physical basis for such an effect was not understood. It was also disturbing that the mass criterion predicted the wrong sign for the Haeffner effect; observations with pure liquid metals revealed that in every instance the lighter isotope was transported to the anode.2 Klemm3 explained these isotopic separations by suggesting that the lighter isotopes were more mobile and more easily carried to the anode with the electron stream. Additionally, several deviations from the mass criterion have been found in liquid alloys, notably involving transition metals such as chromium, nickel, palladium, and zirconium, which migrate to the anode in liquid bismuth.4'5 Recently, a model has been proposed6 in which electromigration in liquid alloys is attributed primarily to the interaction between the electron stream and the metal ions. In essence, this model predicts that the component with the greater electron-ion scattering cross section will be preferentially transported to the anode, displacing the other component to the cathode. The electrical resistivity of each pure component at its melting point is taken as the measure of its scattering cross section. This model was developed from the results of systematic studies with various solutes in liquid mercury,7'8 bismuth,9 and sodium.10 In every alloy, the component with the greater resistivity has centrates at the anode. Coincidentally, in every instance the component with the greater resistivity has also the greater mass, apparently satisfying the mass criterion. In order to differentiate between electron-ion coupling and atomic mass as the relevant physical prop- erty influencing electromigration, measurements were made with Pb-Sb alloys. Lead has an atomic mass nearly twice that of antimony, but lead has an electrical resistivity of 91 microhm-cm while antimony has a value of 113.5 microhm-cm at their respective melting points. The mass criterion predicts that in an alloy of the two antimony will concentrate at the cathode; the electron drag model predicts that antimony will concentrate at the anode. EXPERIMENTAL To conclusively determine the relative motion of lead and antimony in each other, solute electromigration was measured in dilute liquid alloys of antimony in lead and lead in antimony. Both starting materials were 99.999+ pct pure. The measurements were made with the same capillary-reservoir technique previously used for measuring electromigration in liquid bismuth alloys.11 Several changes in the experimental apparatus were necessary, however, to accommodate liquid antimony, which has a higher melting point than bismuth. The modified apparatus is depicted in Fig. 1. In each experiment four quartz capillaries were filled with the molten alloy. A direct current was passed through two of the capillaries; the electrode in one of these capillaries was made the cathode, and the electrode in the other was made the anode. The remaining two capillaries sampled the alloy in the reser-

Jan 1, 1969

By R. K. Adams

The availability of digital computers costing less than $15, 000 makes them economically attractive as versatile research and experiment tools. Several such installations at Oak Ridge National Laboratory have shown that improvements in research productivity and experimental control accuracy can result from the proper application of a small digital computer. However, careful attention must be paid to several potentially expensive problems in 1) interfacing the experiment to the computer and 2) programming the computer. Two specific applications of very small computers to metallurgical testing and research are described. One is a system for data acquisition and precise temperature control associated with a thermocouple testing program, and the other is a system for pulse calorimetry determination of the specific heat of metals over wide temperature ranges and in the neighborhood of metallurgical transformations. The data acquisition system which uses a PDP-8/S computer monitors signals from up to 264 low-level thermocouple signals at two scanning speeds: 10 readings per second for long-term drift data, and 500 readings per second for transient data. The pulse calorimetry system which uses a PDP-8 computer accepts up to 6 signals of 0- to 10-v range and because of a larger analysis program, uses a bulk memory (magnetic disc) in addition to core memory.

Jan 1, 1969

By P. Barnes

The object of this paper is to make a brief comparison of the outlines of several forms of ports for steel-melting turnaces, in reference chiefly to the proper mixture; of the gas and air, and to the direction in which the flame is thrown down into the interior of the furnace. In the illustrations on the accompanying plate, Fig. 1 shows a form of port designed by M, Pernot, of St Chamond, France. This is used with the dome roof preferred by him fur the revolving bottom that bears his name. From No. 1 has been derived No. 2. This is shown on the plans of Mr. A. L. Holley, and from them three large furnaces have been built and put into operation by the Springfield Iron Company. Fig. 3 shows an outline proposed by Messrs. Richmond & Potts for the Pernot furnace. In this the ports are brought in under an arched roof of nearly the ordinary form, instead of over the top of the roof, as with the dome of M Pernot, Fig. 4 shows a furnace as built by Krupp of Essen, Prussia, for fluid refining, or " washing "-—to use the briefer French term. in this the gas and air come into contact in broad sheets one above the other, Fig. 5 shows the form used by Messrs. Richmond & Potts

Jan 1, 1881