Search Documents

By D. S. Sanders, E. W. Witcomb

FLOTATION tests, from which the flowsheet for the concentrator was determined, were made in a pilot mill at Chuquicamata and later comparative testing of full size flotation cells was done at the Andes Copper Mining Co. concentrator in Potrerillos. The principal sulphide copper mineral is chalcocite with varying amounts of covellite, enargite, and chalcopyrite. The oxidized portion is principally antlerite, a green basic copper sulphate. The gangue minerals include quartz, sericite, pyrite, feldspars and kaolin. Chuquicamata pit ores have proved to be hard grinding. The results of the flotation and metallurgical work prove that good extraction and concentrate grade can be obtained under a rather wide range of conditions. Metallurgy In general the metallurgy of the ore requires a fairly close control of the grind to the primary rougher flotation and of the regrind of the primary rougher concentrate before cleaning. Regrinding is necessary to reduce the insoluble content of the final concentrate since a large part of the middling combinations are between the copper and silica minerals. The alkalinity of the pulps can vary between wide limits and control of the percent solids gives the desired grind. Alkalinity Control Arroyo Salado water is supplied to the concentrator head tanks. It contains about 5000 ppm of salts but test work shows no deleterious effect. Actually this water permits a decrease of as much as 1 lb of lime per ton of ore as compared to San Pedro water, which is used for leaching oxide ore. About one quarter of the water flow through the concentrator will be new water from the reservoir. The remainder will be reclaimed from the thickeners. For primary grinding and rougher flotation, new and reclaimed water are combined in the head tanks. To avoid erratic results, only new water is used in the regrind system. Milk of lime is added to the rod mill feed chute to obtain the maximum benefit of mixing with the ore. This protects the equipment from corrosion due to entrained acids and soluble copper salts. Lime consumption is 3 to 5 lb per ton of ore. Grinding and Flotation The six bin gates over each belt feeder are opened in controlled combination and sequence to keep a live bed of ore in the bin to prevent arching and to obtain mixing. The milk of lime added ahead of the rod mill is regulated to suit rougher flotation requirements. The primary promoter reagent, Aerofloat 238, is added to the 10-mesh discharge of the rod mill as it is laundered to the ball mill scoop box. The classifier overflow is regulated to produce a grind of about 12 to 15 pct +65 mesh and 60 pct -200 mesh. A secondary promoter Z-4 (aml zanthate) and the pine oil frother are added in the overflow launder where a pH of 10 to 11 is maintained. Comparatively heavy beds of froth on the

Jan 1, 1952

September 20, 1917. As this meeting terminates the year's agreement under which the Engineering Foundation has appropriated its income to the National Research Council, a brief summary of what has been accomplished seems called for. The Research Council was organized Sept. 19, 1916. The Executive Committee was appointed at that meeting; since that date two other meetings of the Council have been held, one in Boston, on Nov. 13 and 14, the other in Washington on April 19. During the intervals between the meetings of the Research Council, the Executive Committee has conducted all of the business of the Council. There have been 29 meetings of the Executive Committee, 13 in New York up to the first of May, 15 in Washington subsequently, and one in Boston. The meetings in New York were devoted to the organization of the Research Council and especially to appointment of committees. At the outset, the Council had no very clear idea of the way in which it was to organize; there were several other groups of scientific men at work, among them, the Research Committee of the American Association for the Advancement of Science and the Engineering Committee of the Advisory Commission to the Council of National Defense. Time was spent in straightening out these two principal complications, both of which were satisfactorily adjusted. The upshot of these negotiations is to leave the Research Council as the only representative, national body of research men, assisting the Government. During the period up to May, the Executive Committee in New York selected carefully the personnel of some 25 principal committees, and of a large number of sub-committees; so carefully were these chosen that of the entire number, several hundred, there have been only one or two declinations. Some of the important steps in the development of the Research Council are the establishment of the Military Section, composed. of the members of the Council connected with the Government and resident in Washington. This Section put the Research Council into close contact with the most important officials of the Army and Navy. From it has grown the Washington office of the Council, and the recognition of the Research Council as the "Department of Science and Research of the Council of National Defense; " and the establishment of the Washington office after the Council of National Defense had officially recognized the Research Council. About this time Dr. Hale, Chairman of the Council, appointed Dr. Millikan to be Vice-Chairman to represent the Council in Washington, and Dr. Millikan has since then been in charge of the work of the Council. At the request of the Secretary, Dr. Millikan has prepared a brief report of some of the work of the Research Council during its first year, which is appended to this report. It shows that the Research Council has been active in much of the important work. under way in our preparations for war, and that it has rendered effective services to the Government.

Jan 12, 1917

By Thomas M. Turner

Open pit mining, always a demanding task, faces two relatively new problems today: (1) availability of equipment and (2) environmental restrictions. The modern dredge offers relief in both problem areas. Delivery on a major dredge might run 18 to 24 months rather than 60 months; and lowering of the water table is precluded, thus minimizing environmental objections. In addition, a lower first cost and potentially increased efficiency may offer real advantages to the miner who is forced away from his traditional mining methods. What are the objections to the use of a dredge in open pit mining? Perhaps first and foremost is the natural reluctance to change from a successful operation. Who can blame the miner who has developed expertise in the use of the dragline if he is reluctant to change to a new mining technique that requires new and different skills? A part of the same problem is the miners' desire to control the excavation visually in order to delineate sharply between overburden and matrix. This problem can be alleviated significantly by utilizing good boring data and a positive acquisition cutter. In the final analysis, however, if the miner is prohibited from dewatering the area, either he mines the deposit by dredge or not at all. There is little doubt that when the decision is made to remove overburden and/or matrix by dredge, the problems of delineating between overburden and matrix, creation of slimes, and development of mining plans to minimize double handling etc., will be addressed and solved. There are two broad categories of dredges: mechanical and hydraulic.

Jan 1, 1976

By Robert M. Asimow, Bisuddhi Riddhagni

THE use of back-reflection Laue photographs for crystal orientation is standard in many research projects. The time required for the orientation of any given crystal depends largely on luck and the skill of the investigator. In any case, where large numbers of crystals are used, this time can be quite considerable when the standard methods involving a Greninger chart and Wulff net are employed. For this reason the technique described below was developed. This new procedure applicable for cubic crystals (without preparation of new charts) largely eliminates the skill and luck factors and makes possible the determination of orientation in minutes. The procedure works in the following way: the Laue photograph is examined and arbitrarily an important hyperbola is picked out. An important hyperbola is defined as one which contains some spots through which several hyperbolas pass. Such a hyperbola inevitably corresponds to a low-index zone axis. The angles between the reflection planes causing all the spots on this hyperbola can be read directly from a Greninger chart in the usual manner. If the hyperbola contains more than five spots, these interplanar angles will positively identify the zone axis and the indices of each of the reflecting planes. However, initially since neither the zone axis nor the Miller indices of a diffraction spot are known, there are a very large number of possibilities that must be considered. Using tables of interplanar angles to check out every possibility would be quite tedious, so that this approach is not generally used. Instead, various poles are plotted on a stereographic projection. In the cubic system, however, it is possible to plot out once and for all the angles between all planes of a particular zone axis up to some upper limit of Miller indices. This has been done for all low-index zone axes in Fig. 1. Given these charts, it is quite a simple matter to identify the spots of the unknown hyperbola. All that is necessary is to plot the angles read off the Greninger chart to the same scale as Fig. l(b) on a strip of paper. Then this strip can be slid along each zone axis of Fig. l(a) until a good fit is obtained. Once this is accomplished, the Miller indices of each spot are given and thus the orientation problem is solved. To check, it is possible to pick a second hyperbola and see whether a compatible solution is obtained. This is most conveniently done by picking for the second hyperbola one that contains a spot common with the first. If the specimen axis is chosen parallel to the incident X-ray beam, then usually the [ loo] hyperbola will appear on the film as one of the more important hyperbolas and consequently will be either chosen initially or as a check. Using the [100] hyperbola, after the (001) or (011) spots have been identified, the latitude and longitude of the specimen axis can be read directly from the Greninger chart so that it is unnecessary to use a Wulff net for the entire orientation procedure. This makes the operation not only quicker but more accurate. Of course, if neither the first nor second hyperbolas correspond to [loo] then a third hyperbola can be chosen.

Jan 1, 1967

By W. David Leyshon

This paper compares the general characteristics of Florida phosphate rock for the manufacture of fertilizers and phosphoric acid. The subjects covered are relative reactivity for superphosphate manufacture and various properties of the rock for use in phosphoric acid production, including gypsum filterability, sulfuric acid consumption, foaming, relative cor-rosiveness, chemical composition, and others. Comprison will include rocks of North Africa, the western U.S., and other locations. This paper reviews some of the important properties of phosphate rock, giving particular attention to a comparison of Florida phosphate with some of the major phosphates produced in the world. It also discusses some of the techniques available for evaluatine Phosphate. rock for phosphoric. acid and fertilizer use. The use of Florida rock outside the U.S. has been increasing steadily, evidence in itself of certain desirable properties of this rock. Table I is a list of the major producers and exporters of phosphate rock as of 1965. Florida, meaning in this case Central Florida, was the largest producer of phosphate rock and the largest exporter of rock. Of a total world production estimated at 60 million tons, about 50 million tons were produced during 1965 by the areas listed in Table I. One major producing area omitted from Table I and from subsequent evaluations in this paper comprises Nauru, Ocean, and Christmas Islands, whose output totaled about three million tons in 1965. This phosphate is marketed entirely by the British Phosphate Commissioners, primarily in Australia and New Zealand, and does not get into the world market elsewhere to a significant degree at the present time. South Africa, Egypt, Israel, and North Vietnam also produce lesser quantities of rock for the international market, and these materials are also excluded from this review. The phosphate industry is now seeing the introduction of several new areas that will be significant factors in the rock market in the future. The North Carolina and North Florida areas each have capacity at present or in the near future for producing about three million tons per year. The Djebel Onk mine in Algeria has a potential of about 800,000 tons per year. In addition, announcements have been made of significant development of deposits in Peru and in the Spanish Sahara, and sizable expansions are planned in several of the existing areas that are now of minor importance. Competition for the rock market appears to be increasing so that more attention will probably be paid to evaluating phosphates available from different areas. It is not possible here to go into all the properties of even a few of the materials listed in Table I. However, it is practical to discuss some comparative properties important for making phosphoric acid and fertilizers, and to touch on the techniques used for the evaluation of various phosphate rocks. Table II gives typical analyses of the major phosphate rocks available in the world as of 1965. There is, of course, an inherent danger in labeling any analysis as typical, but it appears that variations between two samples of rock within one given area are generally less than between two samples from different areas. The analyses listed were compiled from several years of data so they may not be representative of the present output of any particular area. The range of grades represented by these analyses goes from 66 BPL for Gafsa rock to 85 BPL for Kola

Jan 1, 1968

By Fred C. Bond

SIZE of grinding media is one of the principal factors affecting efficiency and capacity of tumbling-type grinding mills. It is best determined for any particular installation by lengthy plant tests with carefully kept records. However, a method of calculating the proper sizes, based on correct theoretical principles and tested by experience, can be very helpful, both for new installations and for guiding existing operations. As a general principle, the proper size of the make-up grinding balls added to an operating mill is the size that will just break the largest feed particles. If the balls are too large the number of breaking contacts will be reduced and grinding capacity will suffer. Moreover, the amount of extreme fines produced by each contact will be increased, and size distribution of the ground product may be adversely affected.

Jan 5, 1958

By G. M. Ritcey

The design of the plant facilities together with the necessary equipment required for the operation is at an optimum only for the specified plant with its peculiar priorities and preferences. Because many alternatives in design are possible to suit a particular plant, each plant designer and contractor must choose carefully in the selection of the site, design and choice of materials of construction, as well as the type of equipment necessary for the process. Basic factors as efficiency, dependability, simplicity, and safety must be considered early in the construction; while the choice of equipment, materials of construction, possible corrosion problems, automation, maintenance, effluents disposal and tailings dam construction can greatly affect the plant costs. While existing plants are in operation, the know-how gained from the operating experience of those plants can be invaluable in the new plant planning, design, and construction.

Jan 1, 1978

By C. W. Schulties, W. J. Mallio, L. J. Petrovic, J. A. L. Campbell

Roof control comprises about 35% of direct and indirect underground mining costs. In addition, difficulties in estimating roof control costs for new areas lead to the greatest uncertainties when negotiating coal contracts. And obviously, coal cannot be mined if the roof can't be held. Accordingly, there are strong incentives to attack this problem on as many fronts as possible. One successful geological modeling technique for predicting future roof conditions was recently applied at Peabody Coal's Simco mine No. 5, located in Coshocton, Ohio. Benefits derived from it included: - A better identification of areas where poor safety conditions may be encountered. - Improved roof control cost estimates for contract negotiations. - Estimates of time-duration while mining in bad roof areas. - Labor and materials cost predictions in an existing mine. - Productivity increases through prior knowledge of areas to avoid.

Jan 10, 1975

By Arthur Wilson, Frederick Carr

INTRODUCTION 1. The application of retreat longwall mining to the North American coal mining conditions is becoming more advantageous as more experience is gained. The productivity results being achieved and potential possible illustrates that this system can be keystone of future underground coal production. 2. In the American coal fields multi-entry is normally practiced as this allows profitable longwall development with existing equipment and systems. Difficulties are being experienced however in the longwall retreat phase by the collapse of multi-entry roadways and excessive use of supplemental support in the following panel tailgates. In some instances the headgate of an operating face can also be in difficulty. 3. Jim Walter Resources Mining Division is developed on a mining plan that calls for three retreat longwalls at each of its four deep mines which have varying depths of cover and immediate roof and floor conditions. The 63 Mine has experienced longwall entry difficulty and there were differing viewpoints with respect to the best development systems to adopt particularily regarding the number of entries and pillar sizes. In an attempt to reconcile these different points of view J.W.R. asked Dr. Wilson to examine the problem and this paper outlines the new approach developed.

Jan 1, 1983

By D. J. Bourne, G. E. Atwood

The new potash refinery of Duval Sulphur & Potash Co. produced its first tonnage of muriate of potash in November 1951. Full capacity was attained in early 1952. Excellent extraction efficiency is being obtained by the process, which is basically froth flotation. System temperature control is practiced and has proved to be of great metallurgical value through high potassium recovery and. low reagent cost. WHEN Duval Sulphur and Potash Co. recently entered the established potash industry, the vast amount of pioneer work essential in an entirely new endeavor was unnecessary. Thus it was possible to screen and assemble proved techniques into a highly efficient process based on the combined knowledge of the industry. It is hoped that the refinements Duval has added to these cumulative achievements will contribute to the rapid advance of the potash industry and related enterprises. The process selected utilizes as raw material syl-vinite ore typical of the Permian Basin. This ore is principally comprised of interlocked crystals of potassium chloride, about 40 pct, and sodium chloride. Also there is as much as 1 1/2 pct of dispersed clay slime which, because of its nature, highly complicates beneficiation of these ores. The refining method is basically flotation in which the mineral sylvite is floated away from the halite-clay gangue to produce a 60 pct K,O muriate of potash product for the plant-food trade. It departs from established practice in the use of an improved reagent scheme, developed by the company's technical staff, and in

Jan 1, 1954

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) The governing body of the Imperial College of Technology, London, S. W. (Royal School of Mines), will shortly proceed to the appointment of a Professor of Metallurgy. This important Chair has been filled in the past by such eminent metallurgists as John Percy, Sir William C. Roberts-Austen, and others. Inquiry has been received at the office of the Institute for an engineer to examine a mica, deposit in one of the New England States. The position of converter blower at. a side-blow Bessemer steel casting plant is vacant.

Jan 4, 1913

Australian research scientists at the University of Melbourne's Institute of Materials Research have discovered two methods of extracting metals from raw ore, using brown coal. The discoveries could lead to extensive new markets for the brown coal producers of Australia (boasting the world's largest brown coal deposits in the Latrobe Valley region of Victoria), the United States and West Germany. Research on the extraction processes began at the University's Department of Metallurgy in mid-1969 under the direction of Geoffrey Cullen, manager of the Materials Research Institute. In June of this year. Cullen announced that both metal extraction processes, using brown coal, had proven successful.

Jan 1, 1971

SECTION I Page Page Report of Nominating Committee. v Employment li Proceedings of St. Louis meeting. , vi Local Section News.: liv Engineering Foundation, Report Affiliated Student Societies lvi of Secretary xxxviii Forthcoming Meetings lvii Engineering Council xlii. Library lviii Suggested College Course on the Membership lxiii Human Side of Engineering... xlii Biographical Notices: Engineering Societies Club of Alexander Bryden. By C. L. Hawaii xlv Bryden lxxxiii Members in Military Service .... xlv E. F. R o e b e r . B y J. W. Meeting of Board of Directors...' xlvii Richards lxxxv 1918 Dues xlviii Institute Committees lxxxvi Transactions for 1917 xlviii Officers and Directors xciv Personal xlix

Jan 12, 1917

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the first half of March: James C. H. Ferguson, San Francisco, Cal. Capt. A. F. Lucas, Washington, D.C. Henry Adams, Stamford, Conn. Dexter P. Cooper, New York, N. Y. H. A. Wheeler, St. Louis, Mo. L. D. Moore, Chatham, N. J. John M. Sherrerd, Easton, Pa. Hennen Jennings, Washington, D. C. R. T. White, formerly General Manager of the Braden Copper Co., Chile, is to take charge of a copper company in Caucasus, South Russia.

Jan 4, 1914

By John F. Myers

Since the art of comminution has lain practically dormant for many years, it is very interesting that R. T. Hukki approaches the subject with a new concept. One is reminded of the research carried on by A. W. Fahrenwald of Moscow, Idaho, a few years ago. Fahrenwald mounted a steel bowl on a vertical shaft. The balls and ore placed in the bowl were rotated at fast speeds, thus simulating the supercritical speeds used by Hukki. The rolling action of the balls against the smooth shell liner has pretty much the same effect. The action is horizontal in one case and vertical in the other. Both researchers report good grinding activity.

Jan 8, 1958

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) A member of the Institute who has had many years' experience in office management for prominent mining engineering and metallurgical companies, and who is now located in the West, would like to secure an executive position with a firm or company engaged in mining or metallurgy, located in the East, and preferably in New York. No. 139. Member, aged 36, married, graduate mining engineer, 14 years' active experience as engineer, superintendent, and manager of large coal-mining operations. Wide experience in development and operation of

Jan 10, 1914

By John V. Beall

Ten years ago, upon coming home to New York, we had money in the bank, a portfolio of stocks, a rent- controlled apartment overlooking the Hudson and we didn't own an automobile. This was bliss! The just reward of industry and careful management of the fruits of our labor in the mines overseas. Although we kept up a delaying action, the family was pushing hard for a house in the suburbs. We were able to find something wrong with every house that came up but, finally, in a weak moment made the unlikely compromise of putting ten dollars down on a piece of property in Westchester County.

Jan 1, 1971

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Apr. 10 to May 10, 1915: William W. Elmer, Tuttletown, Cal. R. R. Freeman, Jr., Wollaston, Mass. Lawrence Addicks, Douglas, Ariz. Francis R. Pyne, Elizabeth, N. J. W. F. Durand, Stanford Univ., Cal. George B. Pickett, Ophir, Colo. S. P. Cooper, New York, N. Y. R. V. Norris has been elected President of the Columbia School of Mines Alumni Association. Robert C. Sticht has been elected President of the Australian Insti¬tute of Mining Engineers.

Jan 6, 1915

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936