Search Documents

By William Best

OIL burners, oil furnaces, and methods of installation, have been the subject of many articles, but information concerning oil-burning systems, based upon scientific principles, is still in great demand, especially in the manufacturing districts of our country. Fuel oil, as it is termed (this being the residuum from oil refineries), has for many years been of great service to our manufacturers, and has justified its popularity not only by producing a superior manufactured product, but by turning out approximately 50 per cent. more product than can be made with coal fuel under like conditions. To install a system requiring only an oil-storage tank, a small pump, and an oil-supply main with numerous laterals leading to the various burners, furnaces, boilers, etc., is a comparatively simple matter; and, because fuel oil is very volatile, it is not necessary to heat it, even during the winter months in a very cold climate. Furthermore, only a small amount of power is required to atomize fuel oil, this often being done by a positive pressure blower, or by a mechanical burner. An analysis of fuel oil, together with that of various other liquid fuels, is given in Table I.

Jan 2, 1914

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 8, 1979

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

THE bellows are important and necessary agents in most melting processes. In addition to seeing that these have sufficient soft cloth, extend far and wide, and are of good design, including good valves and good long tubes, and that they cannot break and lose the air received, it is very important to give attention to their installation so that they may easily effect their purpose. Therefore I now wish to proceed by noting some common devices for moving them, both with water and with man power, so that you may make use of them as the need arises.

Jan 1, 1942

By E. M. Wise

THE properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. GENERAL REQUIREMENTS In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should be good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depilatories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 lb. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800° and 1200° C.

Jan 1, 1928

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,' transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :'paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :'paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By J. Stuart Warner

The reaction COSO4(c)?CoO(c) + So3(g)was investigated from 950° to 1170OK by two different methods. The sulfate was decomposed in a previously evacuated space and Pso3 calculated from the measured total pressure on the assumption that Pso2 = 2P02. The sulfate was also decomposed under conditions of controlled oxygen pressure. The difference in the results obtained by these experimental techniques is attributed to the effects of thermal diffusion. The standard free energy change for the reaction is given by ?F° = 66,292 + 17.273T log T — 102.57 T (±300 cal/mole). It was found by DTA and X-ray diffraction studies that CoS04 undergoes a transformation at 617°± 4°C. THE metal sulfates may decompose directly to the oxide or pass through one or more intermediate basic sulfates. Provided the oxidation state of the cation does not change in the course of the reaction, the decompositions may be described in general as follows: One of the major objectives of this work was to determine the validity of Eq. [3] as much of the existing sulfate data has been calculated from decomposition pressures by Eq. [5]. The type of apparatus generally used for these measurements consists of a reaction vessel at high temperature which communicates with a manometer at room temperature. A temperature gradient is thus imposed on the gas phase causing thermal diffusion which brings about a partial separation of the different gaseous species present in an initially uniform mixture. The basic theory and experimental facts associated with this phenomenon are summarized elsewhere1 and it will suffice to state here that the heavier gaseous species diffuses down the temperature gradient. Since thermal diffusion destroys the homogeneity of the gas phase, it is not necessarily true that Pso2 = 2Po2 in any particular volume element of the gas phase even though there are twice as many molecules of SO, as of 0, in the gas phase considered as a whole. Under these conditions, the decomposing sulfate gives off SO, which dissociates to SO, and 0, and all three species are distributed throughout the system by thermal diffusion. However, the sulfate will continue to dissociate until the equilibrium value of PSo3 is established on the hot zone. Thermal diffusion may distribute SO2 and O2 throughout the gas phase in any way so long as Eq. [2b] is satisfied in the hot zone; i.e. Pso2(Po2)1/2=K3pso3. When a steady state is reached, we can characterize Pso2 in that

Jan 1, 1962

By Grover J. Holt

A DETAILED description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in I920, and subsequent developments have been described by E. E. Hunner,1 M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,3 it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. [T] The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and "paint rock," directly below the surface material and overlying the ore. Taconite is the iron formation, a ferruginous chert with interbedded slate layers. "Paint rock" is a local term for oxidized slate layers interbedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Besse¬mer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden¬-removal and shaft-mining costs. STRIPPING PRACTICE Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer. In the present emergency many operators are forced to forego the economies attained by year-round utilization of equipment and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be over-equipped and high depreciation charges will have to be absorbed.

Jan 1, 1942

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as 'la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10'5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

By J. C. Draper

Duquesne Light Co.'s Portal No. 3 mine, in the Warwick group of mines in Southwestern Pennsylvania, was started in June 1965 with battery- powered tractor-trailer face haulage. The area as- signed to Portal No. 3 encompasses over 8000 acres of coal and will be developed by driving a set of main entries through the center of the tract in roughly a westerly direction, and sub mains on a 45º deflection angle in roughly a northerly direction (Figs 1 & 2). In the original planning these sub mains were to be at a 90º angle with the mains, but difficult roof conditions necessitated a change in plans. The entries and crosscuts are driven 18 ft wide in the normal Sewickley seam which varies between 46 and 56 in. high. The mine bottom is a strong shale and in average, cool or dry outside conditions stands up well for rubber-tired haulage equipment, but when the outside conditions are hot and humid, the bottom becomes soft and muddy. This condition lessens as the mine faces are advanced further from the portals because the condensation will then take place principally on the surfaces of intake entries outby the working areas. To aid the situation, an air cooling system was installed and is used as conditions dictate.

Jan 7, 1968

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate 0.f solution of nitrogen in y iron in the temperature range 1000° to 1200°C. It is shown that, when purified reacting gas is used, the rate-controlling process is the diffusion of nitrogen into the iron. The difhsiuity of nitrogen in y iron is calculated from the results and the equation logD = —(8800/T) — 0.04 is recommended to represent the temperature dependence of the diffusivity. In some experiments using unpurified nitrogen, solution rates are found to be slower than those attributable to a solely solid-state diffusion process. Indications are that in the presence of impurities in the gas, e.g., H,O, chemisorption of nitrogen at the surface is hindered and becomes a rate-controlling process for the transfer of nitrogen across the gas -metal interface. ALTHOUGH the solubility of nitrogen in y iron at known nitrogen activities has been well-established,'-a the kinetics of the solution of nitrogen in iron are not known. The work of Darken, Smith, and Filer' indicates that at temperatures below about 1300°C the rate of solution of nitrogen in y iron is controlled by a chemical reaction at the metal surface, while at temperatures above about 1300°C the rate-controlling process is the diffusion of nitrogen in the metal. Fast and verrijps studied the denitro-genization of y iron using wet hydrogen at 950°C and their results clearly indicate that the rate of nitrogen removal is controlled by diffusion of nitrogen in the metal. In Part I of this series of papers, the kinetics of the solution of nitrogen in y iron are discussed in the light of the present experimental work. EXPERIMENTAL Apparatus. The reaction chamber consisted of a platinum wire-wound resistance furnace with a re-crystallized alumina reaction tube. The temoerature of the furnace, which was automatically controlled to approximately 1°C, was measured with a Pt/Pt-13 pct Rh thermocouple and a potentiometer. The temperature distribution in the working zone of the furnace was determined using a calibrated Pt/Pt-13 pct Rh thermocouple and the hot zone was found to be approximately 3 in. long with a temperature variation of * 3°C. A series of experiments was also carried out at 1000°C and pressures above atmospheric using a pressure vessel which was similar in construction to that described elsewhere.1° Materials. Ferrovac E grade iron used in all ex-

Jan 1, 1964

By G. J. Wilson

Review of difficulties experienced in drilling directional wells in the offshore Grand Isle Block 43 field showed most failures of drill pipe, drill collars and casing to have been associated with excessive dog-legs. Alleviation of difficulties was approached by synthesizing theoretical and practical concepts in a planned dog-leg control program. Preventive measures necessary to control dog-leg severity and corrective measures used to reduce unacceptable doglegs are discussed. When other measures fail, deliberative measures as outlined can be employed after the probable cumulative fatigue damage to be sustained by the drill pipe has been determined. Results of a program successful in virtually eliminating problems stemming from excessive dog-legs indicate that control of dog-leg severity in directional wells is feasible and will cause no decrease in the over-all drilling rate. INTRODUCTION Prompted by an increasing frequency of drill pipe, drill collar and casing failures, a study of 50 directional wells representing 592,000 ft of hole, including 444,000 ft of deviated hole, drilled in the offshore Grand Isle Block 43 field was conducted in early 1965. A number of drill pipe washouts and six keyseating problems were recorded and a detailed review was made of 16 failures which had required fishing effort in 10 of the 50 directional wells drilled prior to June, 1965. These problem wells are exemplified by Wells G and F for which pertinent data are shown in Figs. 1 and 2. Data pertaining to all of the 16 failures are summarized in Table 1. Inspection of these data shows most of the problems to have been associated with dog-legs in excess of theoretical limits suggested by Lubinski' and excessive dog-legging is indicated to have been concomitant with whipstocking in several of the problem wells. Results of the investigation agreed with those reported by Schenck2 who had concluded that problems could be expected when dog-leg severity exceeded limits proposed by Lubinski. Since Schenck had demonstrated the desirability and feasibility of drilling directional wells without excessive dog-legging, a dog-leg control program was established in June, 1965 for wells drilled in the Grand Isle Block 43 field. This paper reviews the methods by which theoretical and practical concepts were synthesized to develop a program of preventive, corrective and deliberative measures which virtually eliminated problems stemming from excessive dog-legs in directional wells. Dog-legs of a magnitude causing no damage are referred to as permissible +1CONTINENTAL OIL CO. HARVEY, LA.

By Grover J. Holt

A DETAILED description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E Hunner,1 M. H Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,3 it will not be necessary here to do more than review the highlights of current practice Details on any points of interest can be obtained through correspondence with the operators involved.† The iron ores of Minnesota, which have been formed through enrichment, of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and "paint rock," directly below the surface material and overlying the ore. Taconite is the iron formation, a ferruginous chert with interbedded slate layers. "Paint rock" is a local term for oxidized slate layers interbedded in the iron formation, high iii phosphorus, alumina and moisture The iron ores fall into two classes- (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite) The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high+manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. STRIPPING PRACTICE Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer. In the present emergency many operators are forced to forego the economies attained by year-round utilization of equipment and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges will have to be absorbed

Jan 1, 1942

Columbia University, School of Mines, New York, N. Y. For many years the School of Mines published a Quarterly containing many valuable papers on mining, geology and kindred subjects, but the publication has been discontinued for several years and copies are no longer available for general distribution Papers by members of the staff are now sent to the various scientific societies, and only longer works are published by the Columbia University Press Publications of the Columbia University Press deal almost wholly with subjects other than geology and mining but one may be mentioned: Regulating an industry, by A. H. Stockder. An account of the experience of the Germans in attempting to regulate the Rhenish-Westphalian Coal Syndicate in 1893 to 1899; $2.50. For a list of publications, address the Columbia University Press at the above address.

Jan 1, 1933

By C. E. Arnold

In attacking the problems of mining and treating large disseminated copper orebodies such as those occurring in the Miami or the Ray district of Arizona, one of the vital questions to be decided is, "What is the value of the orebody per ton in place?" The importance of this question lies in the fact that its answer helps to reach a decision concerning the method of mining to be employed. Let it be assumed for the moment that milling and smelting practice, especially the latter, is more or less standardized, and has a cost incapable of much variation, while the cost of mining has a considerable range owing to the large number of mining methods by which a mine may be exploited. For instance, a method may be adopted whereby all the available ore can be extracted perfectly clean (i.e., unmixed with barren material) at a relatively high cost; or a method may be used involving the necessary dilution of a portion of the ore with waste, in order to recover that portion, thus giving a relatively poorer extraction but nevertheless a lower working cost than the former method. Naturally, between these two extremes there lie intermediate methods. In order to arrive at a solution of a mining method problem that is of any value, it is necessary that accurate and complete estimates of mining, milling, and smelting performances and costs shall be established. By way of illustration is given a case of mining, by the system of undercutting and caving, a large orebody with an average content of 1.50 per cent. copper supposedly all in sulphide form, to which case has been applied those results in mining operations which one may fairly assume are to be expected when viewed in the light of G. R. Lehman's ore-drawing experiments, which form the subject of a paper to be presented at this meeting. It is assumed that the total costs will be as shown in the table on page 204. To attain these costs, a daily production and treatment of 14,400 tons has been assumed. Other assumptions are as follows: 15 per cent. of orebody is to be extracted clean by development work and undercutting; 63.8 per cent. (75 per cent. of 85 per cent.) is to be extracted clean by caving, leaving 21.2 per cent. part of which is to be extracted by diluting with waste, and the remainder lost. Dilution and extraction are to

Jan 1, 1917

department, first as a practical miner, next. as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company's office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. Captain Ba.llamy's military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers' training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on Aug. 9, 1918. Lieutenant Martin F. Bowles Martin F. BOWleS, born Apr. 25, 1893, at Bonne Terre, Mo., and graduated from the Neodesha, Kans., High School, had finished all but one month of a four-year course in metallurgical engineering at the Missouri School of Mines, Rolla, Mo., when on May 12, 1917, he entered the first Officers' Training Camp at Fort Riley, Kans. At the close of the training period, he was commissioned a Sccond Lieutenant and assigned to Co. B, 355th Infantry, 89th Division, and stationed at Camp Funston. He left this camp with his company on May 21, 1918, and sailed from an eastern port on June 4, ayriving in England on June 15, 1918. After a short stay at a rest camp there, he proceeded to France. On August 14, he wrote that he was with Battalion Headquarters as Gout Officer, 1st Battalion, 355th Infantry, 89th Division. The last letter received from him, dated September 2, was written in his dugout and contained the following: "Here it is 2.45 a. M. Sitting in a dugout waiting for some patrols to report back in, I am writing this by the light of two candles." He was killed in action on the night of Sept. 3, 1918. The letter of notifi-

Jan 1, 1920

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,' the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964

By A. Schild

The effect of heating a producing well on the rate of oil recovery has been analyzed in the simple case of a well producing oil by a radial drive and in the steady state. Differences of production rates with and without borehole heating have been calculated and plotted; these measure some of the benefits of the thermal recovery process. A striking feature is that the production increase tends rapidly to a constant value for large production rates. Some concrete examples, including a rough comparison with field data. are discussed. Heating requirements have been calculated and plotted on the assumption that the heaters used are 100 per cent efficient. Heating has been thought of as applying only to low volume wells producing heavy oils. However, the calculations suggest that the thermal process considered might be profitable even for some wells producing large quantities of light oil, especially in unconsolidated formations where fracturing is not possible. In the case of wells producing other fluids with the oil or of wells producing partly or wholly by gravity drainage, the theory developed does not apply in detail. It can be expected, however, that any general qualitative be-havior will remain valid. Under normal temperature conditions, high viscosity emulsions sometimes form around the wellbore, lowering the permeability in the vicinity of the well and impeding the production of oil. Borehole heating often prevents such emulsification. This important effect is not easily amenable to mathematical analysis and has not been included in the theory presented here. It should therefore be kept in mind that the benefits due to borehole heating may in fact exceed the values given by the following calculations. INTRODUCTION The recovery of viscous, low gravity oils can often be stimulated by applying heat to the production zone. The higher temperature lowers the viscosity of the oil, increasing its mobility, and therefore its rate of production. One thermal method of recovery 1,2,3,4. consists in operating a heater inside a producing well and, at the same time, producing oil from the well. In this paper a simple theoretical model is analyzed to study the effect of such heating on the recovery of oil. The reservoir mechanics of the process is the only aspect of the problem which is considered here. The details of the heating system are ignored, and it is simply assumed that the heater raises the temperature in the immediate vicinity of the producing well to a pre-assigned temperature T w. Although heating requirements are calculated, these refer only to the heat supplied to the formation and to the oil being produced; they do not include heat losses due to the inefficiency of the heater. A short outline of the theory follows: The heat supplied to the producing well flows out into the formation by means of thermal conduction. At the same time, the flow of oil carries heat by convection from the formation towards the producing well. After sufficient time has elapsed, a steady-state is reached where the temperature, the velocity of the oil, etc., no longer vary with time but are functions of position only. In the steady state the temperature decays like an inverse power from the high value Tw at the wellbore to the original reservoir temperature T. at some distance away from the well. The effect of the high temperature and low oil viscosity near the producing well is the same as if the oil were produced at reservoir temperature To but through a producing well of a larger radius. From this point of view, the energy and money being expended to provide heat

Jan 1, 1958