Search Documents

By K. B. Nowels

DATA pertaining to pipe line flow for both oil and gas in horizontal or nearly horizontal pipe lines are both extensive and accurate. However, the pipe formulas used to determine pressure drop for flowing fluids (liquids and gases) under conditions of horizontal flow are not generally applicable to flowing oil and/or gas wells. Except for some data developed in small laboratory set-ups, little or no information was available concerning flow of oil and gas mixtures in vertical pipes, when, in 1928, the writer began the development of a method for computing pressure drops in the pipes of flowing oil wells, as outlined in this paper. In 1929, Uren1 presented some findings based on laboratory experi-ments in which vertical flow of an extremely heavy crude oil was induced, by means of air through a 2-in. pipe, 41 ft. long. The friction factors derived from the experiment, as well as values for pressure drop per 100 ft., are not believed satisfactory in their application to flow problems in the field. Versluys,2 also in 1929, presented a mathematical development of the theory of flowing oil wells, and in 1930, gave a companion paper3 setting forth some principles governing the choice of length and diameter of tubing in oil wells. Since the termination of the study presented in this paper, another. valuable contribution pertaining to the problem, of vertical flow was made by Moore and Wilde.4 Although there were writings dealing with the principles of the gas-lift, a search of the available literature indicated that specific information on vertical flow was lacking with the exception of the writings of Uren, Versluys, and Moore and Wilde, to which reference .has been made.

Jan 1, 1932

By Robert D. Pike

IN November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: [ ] Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2,3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depend¬ing upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1947

By E. P. Mathewson

In a discussion of a paper on The Basic Process as Applied to Copper Smelting, by Percy C. Gilchrist, read before the Society of Chemical Industry, London, Jan. 5, 1891,' Prof. W. C. Roberts-Austen asked Mr. Gilchrist whether he thought that the substitution of a basic lining for acid lining in the Manhks process would afford anything like the service which it had been shown to render in the metallurgy of iron. Claude Vautin stated that he had experimented for over two years. with basic linings for Bessemer converters for copper mattes at Cobar, but had given up the attempt on the score of cost. Mr. Gilchrist in his reply stated that he did not believe in applying any system of Bessemerizing to copper. About the time of the presentation of the paper mentioned,Hermann Keller, Superintendent of the Parrot smelter, in Butte, was experimenting on a large scale with converters lined with magnesite brick. He gave up the idea on account of the cost of linings and because no particular advantage was observed. My belief is that his tuyeres and converters were too small. A short time afterward similar experiments were tried at the Great Falls plant of the Boston & Montana Co., and at the Old Works of the Anaconda Copper Mining Co. in Anaconda. These were abandoned on the score of cost and the lack of advantages. The same cause of failure, in my opinion, holds here. The Anaconda Copper Mining Co., however, adopted the magnesite brick lining for its tilting casting machines. Fig. 1 is a view of the first tilting furnace casting copper. It was made from an old Brueckner roasting cylinder. Fig. 2 shows an elevation and vertical and horizontal longitudinal sections of the second tilting furnace, built in 1897.

Jan 1, 1914

By E. F. Kingsbury

ONE of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist- heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consumption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. SUBSTITUTES FOR PLATINUM During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established.. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time.

Jan 1, 1928

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors' work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By Billy L. Crowder, John M. Fairfield

The implantation of B+ , P+, and As&apos; into silicon has been studied with the purpose of making shallow p-n junctions. The influence of such parameters as 1) ion energy, 2) target orientation and temperature, 3) total dose, and 4) annealing schedule was investigated. An energy range of 70 to 300 kev was used for boron and phosphorus implants and up to 500 kev for arsenic. It is found that the experimental projected range agrees well with theory and that shallow junction depths can be made reproducibly. ION implantation has received much attention recently as a technique for doping semiconductors. Specifically, it has the potential of supplementing or replacing the diffusion process as a method for making p-n junctions. In a few specific cases it has been used successfully to make semiconductor junction devices. Potential advantages of ion implantation doping over diffusion techniques are: 1) It affords greater control of shallow junction depths (< 0.2 µ) while maintaining high peak concentrations. This is particularly important for high-speed switching devices, since lower junction capacitances and resistances can be achieved. 2) More precise registration of small planar structures can be realized if proper masking procedures are employed. This advantage is especially useful in the design of high-density integrated circuits. It has been used to advantage in FET fabrication since the edge of the source or drain can be aligned precisely at the edge of the gate electrode.&apos; 3) Ion implanatation permits lower temperatures than diffusion techniques. This factor alleviates the problem of compatibility of diffusivities often encountered when designing multiple-junction structures. Also, the lower temperatures create fewer thermal defects and dislocations, which may account for the high efficiency of some ion-implanted solar cells.2 4) Impurity profiles can be more easily tailored to resemble ideal distributions. Successful exploitation of the potential advantages of ion implantation techniques will depend on increased knowledge and understanding of the subject. The factors likely to be influential in determining impurity distribution profiles in ion-implanted single-crystal targets have been reviewed by J. F. Gibbons.3 In addition to the mass and energy of the implanted ion, the total dose, target orientation, and target temperature are important parameters. The annealing temperature required for removing lattice damage and incorporating the implanted species on an electrically active site is very important. This paper describes an investigation of some of these factors. Implants of boron, phosphorus, and arsenic into silicon have been studied. Energy ranges of 50 to 300 kev were used for boron and phosphorus and up to 500 kev for arsenic. In addition to the implantation energy, the effects of total dose, target temperature, and post implant anneal have been investigated. EXPERIMENTAL PROCEDURE The implantation targets were silicon wafers cut from Czochralski-grown crystals, lapped, and chemically polished. The orientations were (111), (110). and (100) with misorientations of up to 7 deg from the principal axis. For this study, accurate target alignment (i.e., within 0.1 deg) was not available and quoted misorientation values should be regarded as approximate . The implantation equipment consisted of an ion source, a 300-kev linear accelerator tube, an electromagnetic separator, and the associated target supporting and beam focusing assemblies. The ion source was a simple oscillating electron type source,4 which has been described elsewhere.5 The gaseous compounds BF3, PF5, and AsH3 were used as ion sources for B+, P+, As+, and AS+&apos;. Analyzed current levels of up to 20 pamp could be obtained; however, for this investigation target current levels of 1-3 µ amp were usually employed. The analyzed ion beam was collimated through a double slit (1.4 x 0.4 cm) and swept perpendicularly to the long axis of the slit such that an area of about 2 sq cm on each target was covered. Dosages of around 1015 cm-2 were normally employed, but smaller amounts were also used for comparison. A uniform flux density over the bombarded area was assured by the continuous use of profile monitors similar to those described by Wegner and Feigenbaum.6 Post-implant annealing was accomplished in an argon atmosphere in a temperature range of 600" to 950°C. It was not part of the purpose of this investigation to study the annealing kinetics; however, some isochronal and isothermal anneal experiments were conducted to determine the time and temperature necessary to render a reasonably high portion of the implanted ions electrically active (i.e., higher than 50 pct). Post-implant anneal temperatures of around 900° and 600°C were required for boron, and arsenic and phosphorus implants, respectively. Arsenic and phosphorus implants increased in conductivity rather abruptly at the proper anneal temperature of the isochronal curve, but boron increased more gradually over a wider range. Isothermal anneal curves were reasonably flat after 10 min, so an anneal time of 1/2 hr was used for the experimental results described below. The profiling techniques were: 1) neutron activation analysis, 2) differential sheet resistance,7 and 3) junction staining.8 The differential sheet resistance technique is commonly employed in this type of study. Its principal disadvantage is the uncertainty of the ef-

Jan 1, 1970

By Chi-Yuen Wang, Chaw-Long Chu

The time-dependent volumetric constitutive relation for a San Andreas fault gouge and a consolidated kaolinite are experimentally determined at confining pressures to 200 Mpa, under creep condition and at ultrasonic frequency. At any given pressure, the bulk modulus determined at 1 Mhz frequency is identical to the "elastic" modulus determined at a stepwise change of pressure. After the pressure change, there occur a time-dependent change of volume and thus the effective bulk modulus. The constitutive relations may be modeled by a standard linear viscoelastic medium with pressure-dependent moduli and viscosity. For the San Andreas fault gouge, viscosity increases from 2x10 13 poise, at 17 Mpa, and 10 14 poise, at 100 Mpa. For kaolinite sample, the corresponding values are 3x10 12 poise and 10 13 poise. These results imply that both stress and pore pressure in fault zones may show time-dependent variations in response to a change of state of stress, such as that occurring after an earthquake.

Jan 1, 1982

By R. E. Schilson, F. H. Poettmann

The direct determination of the stabilized performance behavior of low capacity, slowly stabilizing gas wells is extremely time-consuming and wasteful of gas. From both field experience and theoretical considerations, a test procedure has been evolved by which the stabilized hack pressure behavior of such gas wells can he predicted without having to revert to long time flow tests. The method consists of using the isochrona1 test procedure to establish the slope of the back pressure curve, "n", and the short time variation of the performance coeficient, "C", with time. From this short time transient flow data and theoretical considerations, the value of C at large times can he established. By assuming the radius of drainage of a well to be half the distance between wells, one can calculate the stabilization time for various well spacing patterns. Once the stabilization time for a given .spacing has been determined, the value of C can be calculated and the stabilized back-pressure curve can he. establbrhed. The calculated perfortnance coefficient as a function of tinze was cotnpared to the experintentally measured values for a number of gas wel1.e. The deviation of the calc~*lated from the cxperimental res1tlt.s vary depending on the set of short time experimental points used to evabrate the parcrttzeters of the equation. The longer the tirne far the flow test data user1 in the calculations, the better was the agreement with the experimental results. The time necessary to obtain this data from well tests varies consitlerably, depending on the physical natrcre oj the rt3scrvoir under consideratiot~. INTRODUCTION For many years, the U. S. Bureau of Mines Monograph 7&apos; has served as a guide for testing and evaluating the performance of gas wells by means of the back-pressure method. The back-pressure performance of a gas well is expressed by the following equation: Q~ CW-W.........(I) where the characteristics of the back-pressure equation are determined by C, the performance coefficient, and n, the exponent which corresponds to the slope of the straight line when Q and {P* - PN2) are plotted on logarithmic paper. Q is gas flow rate at standard conditions, and P, and P, are equalized and flowing bottom-hole pressures, respectively. Prior to the development of the back-pressure tcst, the "open flow" capacity method of testing a well was common. By this method, the wells were flowed wide open to the air and the flow rate measured. Such procedure was wasteful of gas and did not provide information on the deliverability of the gas to the pipe line. Monograph 7 Procedure The back-pressure method of testing wells was developed to overcome these shortcomings. Although much has been learned regarding the laws of the flow of gas through porous formations, the original development of the back-pressure relationship was based entirely on empirical methods. The back-pressure behavior provides the engineer with information essential in predicting the future development of a field. It permits him to calculate the deliverability of gas into a pipe line at predetermined line pressures, to design and analyze gas gathering lines, to determine the spacing and number of wells to he drilled during the development of a field to meet gas purchasers&apos; requirements, and to solve many other technical and economic problems. As described in Monograph 7, the flow-after-flow method of back-pressure testing, when applied to fast stabilizing and usually high capacity wells, correctly characterized the behavior of the well. However, as the value of the gas at the wellhead increased, small capacity gas wells having slow rates of stabilization became economically operable. The flow-after-flow method of testing could not be used to describe the behavior of these slowly stabilizing wells. The procedure of Rawlins and Shellhardtl for establishing the back-pressure behavior of a gas well was based on the rcquirement that the data be obtained under stabilized flow conditions; that is, that C is constant and does not vary with time. C depends on the physical properties of the reservoir, the location, extent and geometry of the drainage radius, and the properties of the flowing fluid. In a highly permeable formation, only a very short period of time is required for the well to reach a stabilized condition, and, consequently, the requirements for the test procedure described in Monograph 7 are met. For a given well, n is also constant

By Stephen L. Bolivar, Susan H. Balog, Thomas A. Weaver

A data-classification scheme was developed to detect potential uranium mineralization in the Montrose l º x 2º quadrangle, Colorado. The methodology developed is a rapid and efficient method of resource evaluation on a reconnaissance scale. The necessary techniques were developed and refined to digitize, integrate, and register various large geological, geochemical, and geophysical data sets for the Montrose quadrangle, Colorado, using a grid resolution of 1 km. All data sets for the Montrose quadrangle were registered to the Universal Trans- verse Mercator projection. The data sets include hydrogeochemical and stream sediment analyses for 23 elements, uranium-to-thorium ratios, airborne geo- physical survey data, the locations of 90 uranium occurrences, and a geologic map (scale 1:250 000). Geochemical samples were collected from 3965 locations in the 19 200 km2 quadrangle; aerial data were collected on flight lines flown with 3-5 km spacings. These data sets were smoothed by universal kriging and interpolated to a 179 x 119 rectangular grid (each grid block is 1 km2). A mylar transparency of the geologic map was prepared and digitized. All possible combinations of three, for all data sets, were examined for general geologic correlations by utilizing a color microfilm output. Subsets of data were further examined for selected test areas. A classification scheme for uranium mineralization, based on selected test areas in the Cochetopa uranium district, is presented. Areas favorable for uranium mineralization, based on this scheme, were identified and are discussed.

Jan 1, 1982

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district&apos;s production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state&apos;s total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district&apos;s production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state&apos;s total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.&apos; The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898&apos; C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.&apos; The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898&apos; C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By O. N. Cole, R. E. Davis, T. D. Brotherton

Pvfoperties of rubidium and cesium are compared with those of other alkali metals. Methods for the preparation of rubidium and cesium metal are reviewed briefly, ad hazards and safety precautions required in handling rubidium and cesium metal are described. SimPle methods for handling laboratory quantities of elemental rubidium ad cesium under oil and under argon are illustrated. CESIUM and rubidium were both discovered by Bunsen and Kirchoff in the years 1860 and 1861. Cesium was discovered while Bunsen and Kirchoff were making a spectrographic study of spring water from Durkheim, Germany. It was the first element discovered by this technique. The element was given the Latin name "caesius" for sky blue because of the color it imparted to flames. Elemental cesium was first prepared by Setterberg in 1881 through electrolysis of a molten mixture of cesium and barium cyanides.&apos; In 1861, Bunsen and Mirchoff discovered rubidium while making a spectrographic study of the alkali content of lepidolite ore from Saxony. Two prominent dark red lines appeared in the spectrum and so the element was named "rubidius" or dark red. In 1861 Bunsen and Kirchoff first prepared elemental rubidium through the electrolysis of molten rubidium chl~ride.~ The alkali metals are very similar in their chemical and physical properties. They are the most active metals, and all exhibit a single oxidation state of one. They are so reactive that they are never found in nature in the elemental state. The reactivity of he metals increases with atomic number. Rubidiurn and cesium ignite spontaneously in air and react explosively with water. This extreme reactivity makes necessary special equipment and techniques for the safe preparation and use of the metals. The cation: of Group IA can be separated from the metallic cations of other groups with relative ease, but the separation of the individual alkali cations is much more difficult because of their close chemical similarity. This close chemical and physical similarity of alkali metals can be inferred from the atomic radii, oxidation numbers, and ioni-zation potentials shown in Table I. A difficult but the most practical physical method of separating the elemental alkali metals from one another is by distillation. Only lithium has a boiling point sufficiently far-removed from the boiling points of the other alkali metals to make this method of separation feasible without elaborate and expensive equipment. This method is not used, however, for lithium because it possesses sufficient chemical dissimilarity from the other alkalies for it to be separated relatively easily as lithium hydroxide monohydrate or as lithium carbonate. Francium, the last member of the group, has no known stable isotopes. The naturally occurring

Jan 1, 1962

By V. E. Elliott, C. L. Meyette

THE conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams -and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a useable and relatively simple solution to a bothersome problem. BASIS FOR CLASSIFYING In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will he used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined&apos; as a zone of

Jan 1, 1948

By E. O. Fromm, R. I. Jaffee, R. M. Evans

IN connection with a research on gallium alloys, a method for the thermal analysis of very low melting alloys was developed, which appeared to be worthy of more than passing interest. As used, the method was suitable for work in the temperature range, — 72° to 250°C. However, with suitable adjustment, the method could be adapted for use over broader temperature ranges. The Rosenhain temperature gradient furnace,&apos; adapted for low-temperature use, was the basis for the method. The gradient was set up in a stainless steel tube. The specimens were lowered through it at a constant rate while time-temperature or inverse rate data were taken. It was essential to maintain careful control of the top and bottom temperatures of the gradient. Also essential was good heat transfer from the walls to the specimen. This was accomplished by a liquid heat-transfer medium.

Jan 1, 1953

By D. J. Carney, J. Chipman, N. J. Grant

An absolute calibration has been achieved for sampling and analyzing liquid steel for hydrogen based on Sieverts&apos; values of hydrogen solubility in iron. Further checks were made in nickel, iron-nickel, and 18-8 stainless melts. The sampling method was successfully applied to a large number of commercial steel melts in various types of furnaces. The concurrent problem of sample storage was also solved. THE problem of sampling of liquid steel for hydrogen is more difficult than the problem of analysis. Hydrogen has a greater mobility than any other element; it is the only element that will diffuse out of steel at room temperature. In accordance with the known relation between temperature and diffusivity, the diffusion of hydrogen is extremely rapid at the temperature of liquid steel. Consequently, in the past, attempts to quench molten steel to retain the dissolved hydrogen have not been as successful as similar attempts with nitrogen or oxygen. The retention of hydrogen is especially difficult since it will continue to escape at room temperature even if the molten metal has been rapidly quenched. The hydrogen sampling methods may be classified broadly as (1) the rapid quenching techniques which attempt to preserve super saturation and (2) those methods which attempt to collect the gases evolved as the metal freezes and cools to room temperature. With all methods of sampling but especially with the rapid quenching methods, there is also a concurrent problem of storing the sample until analysis is undertaken. The two problems are interrelated and must be considered together when discussing liquid steel sampling techniques. The major obstacle in liquid steel sampling has been that there was no way of evaluating properly the various sampling and storage techniques which have been developed. It has not been possible to compare the accuracy of the various methods. For evaluation of sampling methods some known standard is required; this may be found in the published work on the equilibrium solubility of hydrogen in liquid iron which has been determined in three separate investigations.1,2,3 The data are shown in table I. Sieverts&apos; original method of obtaining gas solubilities involved measurement of the volume of gas required to saturate the liquid metal contained in an evacuated bulb of known volume. This procedure, improved by introduction of high frequency induction heating, has yielded reproducible results which appear to be entirely dependable. Using Sieverts&apos; method, it has been proved for iron and other metals and alloys that the hydrogen solubility is proportional to the square root of the pressure of the hydrogen gas above the liquid, so that one may work with various partial pressures of hydrogen to put different amounts of hydrogen in solution. From Sieverts&apos; law it is possible to know accurately what amount of hydrogen is dissolved in the liquid metal at the time of sampling. The accuracy of a sampling method may be gauged by reference to this known solubility. It was the purpose of this investigation to develop a method for sampling liquid steel and for storing the sample so that the analytical result would represent the actual hydrogen content of the metal bath. For this purpose an induction furnace was

Jan 1, 1951

By I. A. Lange, A. M. Richardson

Although methods for determining shaft lining thickness are well documented, little attention has been given to the design of station breakouts and other related shaft ground support structures. This paper discusses design of selected shaft structures for the Cathedral Bluffs project, a planned 54-kt/d (60,000-stpd) oil shale mine in western Colorado. Design philosophy and construction sequences used in the three completed 520-m (1700 ft) deep, 4.6-m (15 ft) to 10.4-m (34-ft) diameter shafts are described.

Jan 1, 1984

By C. G. Dunn, P. K. Koh

TWO recent review papers have considered the origin of primary and secondary recrystalliza-tion textures from the point of view of oriented nucleation and oriented growth theories."&apos; Both theories require nuclei for primary recrystallization but provide no unequivocal answer to the question of what nuclei are. The answer to the same question regarding secondary recrystallization, however, often is that nuclei are certain primary recrystallization grains or primaries. The two theories differ, however, in specifying what the certain primaries are. In support of the oriented growth theory Beck and Hua originally stated "It may be assumed that in a re-crystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as nuclei for the coarse grains, provided that conditions are favorable for their growth." In commenting on this statement one would say that there are two restricting conditions: namely, that 1) the certain primaries (nuclei) are large enough to grow, and 2) their boundaries have high mobility. More recently Beck2 has con-

Jan 1, 1958

By C. J. Bise, E. K. Albert

Mathematical modeling and computer simulation are the two primary techniques used for production analysis of underground coal mine layouts. Oftentimes, however, the selection between these two techniques is not based on an awareness of the level of effort needed for input formulation versus the suitability of the desired output. This paper will review mathematical modeling and two of the more prominent simulators (Virginia Tech&apos;s FACESIM and Penn State&apos;s UGMHS) used in underground coal mine production analysis. A hypothetical section will be analyzed by these programs and, based on the results of the aforementioned study, their advantages and disadvantages will be discussed.

Jan 1, 1985