Search Documents

By Mark R. Lamb

THE various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it. is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, "What is the actual period of treatment undergone by the pulp?? One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true to only a limited extent. The greater the number of tanks the greater is the percentage of chance that all the pulp will be treated equally. Without going into the mathematical analysis of the problem (which is of little value, since it is based on problematical premises), its important terms may be clearly grasped by thinking of, or " visualizing," the conditions when,

Jan 1, 1910

By Dennis J. McCarthy

TAX TREATMENT OF EXPLORATION AND DEVELOPMENT EXPENSES Exploration Expenditures General Principles. Exploration expenditures are expenses incurred within the United States or the Outer Continental Shelf for the purpose of ascertaining the existence, location, extent or quality of any deposit of ore or other mineral. Section 617 of the Internal Revenue Code permits a taxpayer to elect to deduct these expenditures currently. In default of election, exploration expenditures must be capitalized and included in the basis of the mineral property for purposes of determining cost depletion. Entitlement to Deduction. In order to qualify for current deduction, exploration expenditures must be incurred prior to the commencement of the development stage, i.e., when mineral deposits are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation. Generally, expenditures for geological and geophysical investigations, reconnaissance, surveying, testpitting, trenching, drilling, driving of exploration tunnels and adits and similar types of work constitute exploration expenditures if incurred prior to the commencement of development. However, expenditures to further delineate the extent and location of an existing commercially marketable deposit are not exploration expenditures. Exploration expenditures may be incurred from within a producing mine to ascertain the existence of what appears to be a different ore deposit. Expenditures for property which is subject to an allowance for depreciation are not deductible under §617. However, depreciation properly allowable on assets used in exploration is an exploration expenditure. Election to Deduct Exploration Expenditures. The election to deduct exploration expenditures is made by deducting these expenditures in the return for the first taxable year for which such treatment is desired. The election applies to all properties of the taxpayer. Once the election is made all exploration expenditures, in the year of election and thereafter, must be deducted, unless the election is revoked with the prior consent of the Commissioner. The Tax Equity and Fiscal Responsibility Act of 1982 (TEFRA) made substantial changes in the treatment of exploration expenditures. For exploration expenses incurred after 1982 and before 1984 by a corporation, the amount currently deductible is limited to 85% of the expenditure. The remaining 15% must be capitalized and recovered over a five-year period. Although exploration costs capitalized under this provision are not part of the basis of the property for cost depletion purposes, investment credit may be claimed with respect to these expenditures. Further changes have been added by the Tax Reform Act of 1984 with respect to expenditures made after 1984. The Act reduces the amount of otherwise currently deductible costs from 85% to 80%. Additionally, it limits the availability of the investment credit for capitalized mineral exploration costs to deposits located in the United States. TEFRA also allows individuals a special method of recovery under which exploration expenditures may, at the election of the taxpayer, be amortized ratably over a 10-year period beginning with the year in which the costs are paid or incurred. If taxpayer does not use this method, the excess of the exploration expenditures actually deducted over the amount that would have been deducted if 10 year amortization had been elected is an item of tax preference subject to the alternative minimum tax.

Jan 1, 1985

By F. D. Delve

RECENT studies by the author on the reduction of titanium from TiO2-bearing slags have been accompanied by difficulties that are attributed to

Jan 1, 1959

In December, 1927, the Institute published two papers on the Brad-ford pool, which were presented at the New York meeting in 1928. Pamphlet copics may be obtained by writing to the Secretary's office for: Oil-field Waters of the Bradford Pool, by Paul D. Torrey. Technical Publicalion No. 38. Some Factors Influencing Production of Oil by Flooding in the Bradford and Allegany Fields, by Paul D. Torrey. Technical Publicaliol No. 39.

Jan 1, 1928

By Edward T. Koch

A new concept involving the use of a crawler-mounted slurrifier for open-pit ore mining and overburden removal is dealt with. The design and application are discussed. Based on field experience, the area and type of operation where this machine would be effective is indicated. The slurrifier is also compared with draglines, shovels, and bucket wheel excavators. A number of the design concepts, as well as the mechanical and operational parameters, are discussed.

Jan 1, 1976

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (I) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1938

By D. Jeulin

For iron ore sinters to be good blast furnace burden, they need to possess certain basic properties such as cold mechanical strength, reducibility, etc. Relations between such basic parameters and sintering parameters (composition of the mix, fuel consumption, operating conditions of the sintering plant, etc.) are not always well understood. For example, one cannot explain the differences in quality noticed for sinters having the same chemical composition. In this paper a new approach is proposed for the characterization of iron ore sinters by a quantitative description of their morphology. The Texture Analyzer LEITZ T.A.S. is used for this purpose and such morphological parameters as sizes of microstructures and the size distribution of phases are measured on samples of sinters. The results indicate that these measurements can be correlated with the sinter quality.

Jan 1, 1977

By R. E. Lamborn

A summary of oil and gas development in Ohio for 1935 must necessarily be brief. As attention of the state government to the oil and gas industry has never included the collection and compilation of statistics on production, either by producing sands, by counties, by fields, or for the state as a whole, such information as requested in Table 1 of this symposium is impossible to secure for this state. In the absence of production data chief attention must be directed to drilling activity for the year. Information such as can be compiled from various sources, including weekly drilling reports to operating companies and trade journals, is given in the following paragraphs with the realization that the data may not be complete in all its details. Drilling Activity by Fields Drilling activity during 1935 was similar to the preceding year in , that the major operating companies were generally content to drill lease-requirement and offset wells and in that comparatively little effort was made to discover new pools. A compilation of completions recorded in weekly reports to drilling companies and in trade journals show 1022 tests completed for the year in 53 counties of the state. Of this total number, 653 wells were commercial producers and 369 were classed as dry holes. Production was secured in 40 counties from formations ranging in depth to 5700 ft. and ranging in age from Middle Ordovician to upper Pennsyl-vanian. From the standpoint of new production for the year, the most important sands are the Clinton of Silurian age, the Berea of Mississippian age and the Shallow sands of Mississippian above the Berea and of Pennsylvanian age. Trenton Sand Field Production in the field of Trenton sand, which originally included parts of 15 counties in northwestern Ohio, is now on the decline. Seventy-three completions were reported in this field during 1935, of which 33.8 per cent were dry holes. Activity centered in Allen County with 12 completions, two of which were dry holes; in Hardin County with 11 producers; and in Wyandot County with 12 producers and 2 dry holes.

Jan 1, 1936

By R. E. Lamborn

A summary of oil and gas development in Ohio for 1935 must necessarily be brief. As attention of the state government to the oil and gas industry has never included the collection and compilation of statistics on production, either by producing sands, by counties, by fields, or for the state as a whole, such information as requested in Table 1 of this symposium is impossible to secure for this state. In the absence of production data chief attention must be directed to drilling activity for the year. Information such as can be compiled from various sources, including weekly drilling reports to operating companies and trade journals, is given in the following paragraphs with the realization that the data may not be complete in all its details. Drilling Activity by Fields Drilling activity during 1935 was similar to the preceding year in , that the major operating companies were generally content to drill lease-requirement and offset wells and in that comparatively little effort was made to discover new pools. A compilation of completions recorded in weekly reports to drilling companies and in trade journals show 1022 tests completed for the year in 53 counties of the state. Of this total number, 653 wells were commercial producers and 369 were classed as dry holes. Production was secured in 40 counties from formations ranging in depth to 5700 ft. and ranging in age from Middle Ordovician to upper Pennsyl-vanian. From the standpoint of new production for the year, the most important sands are the Clinton of Silurian age, the Berea of Mississippian age and the Shallow sands of Mississippian above the Berea and of Pennsylvanian age. Trenton Sand Field Production in the field of Trenton sand, which originally included parts of 15 counties in northwestern Ohio, is now on the decline. Seventy-three completions were reported in this field during 1935, of which 33.8 per cent were dry holes. Activity centered in Allen County with 12 completions, two of which were dry holes; in Hardin County with 11 producers; and in Wyandot County with 12 producers and 2 dry holes.

Jan 1, 1936

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By Albert F. J. Bordeaux

Alluvial gold was first discovered in Guiana in 1852, in the sands of the Arataye river, by Paulino, a Braziliaii convict. During the following years, gold was found also in the rivers Orapu, CirubQ, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Vat, and Couriege. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysee, Pas-Trop-Tot, date from 1878, and their production has been about %g5,000,000. In 1888, the Awa placers, along the boundary bet.ween the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company, the Dutch Guiana Freiich Minillg Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have produced about $18,000,000 in six years (1894-1900), but not even one-fourth of tho production went through French Quiana and

Jan 1, 1911

By Dewitt T. Ring

Reliable and detailed data covering the enormous number of wells drilled and the long historical production of the state, many of which were never recorded until recent years, render it impossible to gather statistical material suitable for the Institute's standardized form. The total production of crude oil in Ohio for the year was 3,654,503 bbl., which is less than the total production in the United States for the peak day of August 1937. For a period of eight years, from 1895 to 1902 inclusive, Ohio produced more oil than any other state. During the year, 1271 tests were drilled in the state, or 114 more than in 1936. Of these, 317 were oil wells, with an initial production of 7088 bbl., an average of 22.3 bbl. per well; 503 were gas wells, with an initial open flow of approximately 222,441 M cu. ft., or 443 M cu. ft. per gas well drilled; 451 were dry holes, that is, 35 per cent of the total completions. A number of factors account for the steady decline of oil production in Ohio. In the state, at the close of thc year, there were fewer than 28,122 producing oil wells. In 1936, there were 30,150 operated oil wells with an average yearly production per well of 126 bbl. The production for 1937 averaged 130 bbl. per well. During the year, 2028 oil wells were abandoned. In other words, old wells are being abandoned more than six times faster than new ones are being drilled. Since the inception of the oil and gas industry in Ohio, between 150,000 and 160,000 wells have been drilled in the state; new potential territory, offering desirable locations for either oil or gas, is becoming increasingly more difficult to find; the dry-hole percentage will continue to increase. Prices Another factor directly affecting the crude situation during the year was the matter of price and proration of Pennsylvania grade oil. The posted price for Pennsylvania grade in Ohio on June 7 was $2.37 per barrel; at the close of the year, it was $1.70 per barrel, or a reduction of 28 per cent in price. In addition to this price cut, a 50 per cent pro-

Jan 1, 1938

By W. L. Zeigler

THE tailing from the gravity concentration plant of the Hecla Mining Co., Gem, Idaho, was former-ly loaded into railroad cars to be used for ballast, highway surfacing material, or concrete work, or dis-posed of by an aerial tramway, which dumped it into another gulch. The tailing averages about 1.2 per cent lead and 0.8 oz. silver to the ton. Further treatment for the recovery of the valuable metals had been investigat-ed several times with results that did not warrant the construction of a retreatment plant; but early in 1925 experimental work was again started with small tests, and later with a 10 tons per day flotation test plant. This showed that the tailing could be ground and treat-ed by flotation at a profit. It was decided to make the new flotation plant an addition to, rather than incor-porate it in the old concentrator, the original capacity of which had been increased many times, the present arrangement being by no means ideal. The old mill buildings were of timber and board contruction, creat-ing more or less fire hazard, so all new construction was made fireproof. Construction work on the new plant was started in the middle of July, 1925, and the plant was placed in operation early in December. The building is of concrete and steel with hollow tile walls, steel sash and corrugated asbestos roofing. The ball-mill floor has for its foundation a cellular reinforced concrete block about 14 ft. deep, extending to cemented river gravel, and the cells filled with tailing to give weight to the block. Overhead, built into the steel frame, is a 5-ton hand-operated traveling crane. With both ball-mills running fully loaded, there is not the slightest trace of vibra-tion in the foundation or building. The flotation floor is of reinforced concrete beam construction and spans Canyon Creek. Adjustable plunger feeders are arranged under the the tailing-bin, which feed by gravity to a 14-in. eleva-tor, discharging to a short 18-in. conveyor. From the conveyor the tailing is discharged into a dividing hop-per, from which point the plant is arranged in three separate units. Each unit consists of a ball-mill in closed circuit with a classifier, and an 8-cell flotation machine and has an approximate capacity of 300 tons per 24 hours.

Jan 8, 1927

By Oliver B. Hopkins

Peru produced approximately 17,466,620 bbl., of oil during 1937, or slightly less than the record high of 17,593,700 bbl. established during 1936. As in 1936, the entire output of the country was derived from the La Brea-Parinas, Lobitos-Restin and Zorritos fields in the northwestern part of the country. Outside of the proven areas, drilling was 'continued by the Peruvian Government in the northern province of Tumbes on the reserved zone at Zorritos. Drilling was carried out on three locations, two of which are understood to have been abandoned during the year. In southern Peru, further attention was given by Government engineers to the Pusi and Saman districts and plans are being worked out for the commencement of drilling operations in the near future in the vicinity of Pirin. Activities in the montaiia region in eastern Peru were continued by the Compafiia Petrolera El Ganso Azul. This company acquired the interest of the Selden Breck Co., and holds some 90,000 acres along the Pachitea River a few miles above its confluence with the Ucayali. During the year, the preparation of a landing place, the cutting of a 12-km. (71/2-mile) road from the river to the drill site, and the construction of a camp were undertaken. Equipment for drilling on this company's concessions has already arrived in South America. La Brea-Parinas Estate.—Production of crude oil on the La Brea-Parinas Estate of the International Petroleum Company Limited amounted to 14,722,754 bbl. during 1937, a decrease of 403,736 bbl. from the all-time high reached during 1936. The total production from 1890 to Dec. 31,1937, was 178,390,767 bbl. During 1937, a total of 141,653 ft. was drilled, 129,516 ft. in new wells and 12,137 in deepening existing wells. In all, 57 wells were completed, 47 of which produced oil, 2 were gas wells and 8 dry. holes. Twenty-nine wells were cleaned out or deepened during the year. The average depth of new wells completed during 1937 was 2367 ft. compared with 1984 ft. for the new wells completed during 1936. There was an increased use of rotary tools during the year and this method is now used to a greater extent than the cable-tool method, which formerly predominated. Of the 57 wells completed during the year, 31 were

Jan 1, 1938

By J. P. Nielsen

When two grains in a polycrystalline specimen meet at a point in the course of grain-boundary movements, and the new boundary created at the point is one of relatively low specific free energy, a nonequilibrium boundary condition occurs. The nonequilibrium is enhanced if the other grain boundaries involved at the point of meeting are relatively high in specific free energy. The nonequilibrium results in a correction by growth of the complex grain (two subgrains) to a large size, sufficient in many cases for it to become a self-propagating unit, i.e., a recrystallization grain. This mechanism, herein called "geometrical coalescence," is proposed as a logical origin for recrystallization nuclei, particularly for secondary recrystallization. RECENT publications1-' indicate that considerable progress has been made toward a complete understanding of the three microstructural processes in metals: recovery, recrystallization, and grain growth. However, a major problem persists, namely, the origin of recrystallization nuclei. It is generally accepted that once a recrystallization nucleus, a secondary recrystallization nucleus particularly, has reached a certain size, it will continue to grow at the expense of its neighbors, simply as a consequence of grain-boundary free-energy considerations. What has remained obscure, however, is the mechanism whereby such a nucleus comes into being and grows to the self-propagating size. Recrystallization Nucleation in a Two-Dimensional Grain-Boundary System In the left portion of Fig. 1 is shown schematically the meeting of grains 1 and 4 on disappearance of boundary 2-3, i.e., the boundary that existed between grains 2 and 3, as might happen in the course of normal grain-boundary migration. If, by chance —and the probability is not necessarily small— grains 1 and 4 are close together in their mutual orientations, or in some other special way mutually oriented so that the new common boundary has relatively a very low specific free energy (hereinafter referred to by s), then the grain boundary arrangement as depicted in the figure is highly unstable. This is particularly so if boundaries 1-3, 3-4, 4-2, and 2-1 are high in their s values. Assuming, for the sake of argument, that boundary 1-4 has a s equal to zero, and the s's of all the other boundaries present are equal to each other and constant, then the boundary arrangement on the right in Fig. 1 will be

Jan 1, 1955

By L. D. Godshall

The extreme difficulty of obtaining a short and, at the same time, exact method for the determination of gold and silver in copper-materials has been well illustrated in "Assays of Copper and Copper-Matte," and its discussion, by Dr. A. R. Ledoux and other leading authorities on this subject.* Two general methods were used by the numerous assayers who took part in the symposium initiated by Dr. Ledoux, and whose results are given in the paper and discussion. One of these is the dry or fire-method, consisting of scorification and cupellation, the former being repeated if the percentage of copper is very high, all slags and cupels being assayed and the results so obtained added to the ordinary assay; and the copper retained by the silver buttons being determined and deducted from the combined weight of the buttons obtained from the assay of the original material, the scorification-slag, and the cupel. The other is the wet or combination-method, which, while not involving so much work, requires a longer time. Briefly, it is as follows : The material to be assayed is dissolved in nitric acid, the solution is diluted, and the fine undissolved gold is collected by means of sulphate of lead, formed by the addition of lend acetate and sulphuric acid to the solution, After standing from 12 to 24 hours, the precipitate is filtered off, and the silver in the filtrate is precipitated as a chloride or bromide, and collected by means of sulphate or bromide of lead. The solution containing this precipitate in suspension is again allowed to stand until the precipitate has settled. It is then filtered; both precipitates, containing the gold and silver, are dried, ignited and scorified, either separately or together, and the result is cupelled in the usual way.

Jan 1, 1901

By D. Mills, G. B. Craig

ZIRCONIUM has been float-zone-refined in an electron-beam furnace and the redistribution of oxygen, iron, and tungsten has been measured. The iodide zirconium used in the present experiments initially contained both oxygen and iron in the range 100 to 200 ppm by weight, and tungsten in amounts less than 10 ppm. Float-zone refining of zirconium, using induction heating, has previously been attempted by Kneip and Betterton1 and Langeron.2 Kneip and Betterton were primarily interested in the removal of iron and nickel. They achieved some purification, with respect to both these elements, in material given up to six passes at 150 mm per hr under an argon atmosphere. Langeron reported purification for a large number of elements after four completed passes in a static vacuum system operating at pressures less than 10-6 mm of Hg and with rates of zone travel between 30 and 40 mm per hr. He did not report oxygen concentrations, but stated that there was inverse segregation of this element. westlake5 has also used a minimum of four zone passes to remove iron from zirconium. No rates or conditions were given. Belk6 has shown that tungsten contamination can occur during electron-beam melting. He reported an increase from 0.01 to 0.05 pct by weight tungsten in molybdenum after four complete zone passes. The vacuum system for the electron-beam unit used in the present investigation consisted of a single-stage rotary pump backing a liquid-air-trapped oil-diffusion pump. A pressure of less than 10-8 mm of Hg was obtained with Dow-Corning 705 fluid in the diffusion pump. In order to avoid contamination of the zirconium by evaporation from the tungsten filament, a special focusing cage4 was employed. Three rates of zone travel, 114, 38, and 4 mm per hr, were investigated, with the liquid zone moving from the bottom to the top of the bar. The bars used were 3 mm diam and the total melted length was 130 mm. Oxygen was analyzed by neutron-activation analysis using a neutron flux of 10' neutrons per sq cm per sec to form the isotope N16 by the 016 (n,p) N16 reaction. The standard deviation is quoted for each oxygen determination. The iron and tungsten analyses were performed spectrographically, and the precision is estimated to be ±6 pct. Analyses for tungsten were all below the detectable limit of 10 ppm, confirming the protection given by the focusing cage. No significant redistribution of oxygen was found at the two higher rates of zone travel. The redistribution of oxygen and iron obtained after five passes at a rate of zone travel of 4 mm per hr (1.1 x 10-4 cm per sec) is recorded in Tables I and 11. Burris, Stockman, and Dillon3 have estimated the distribution of solutes during multipass zone refining. Using their curves for an effective distribution coefficient of Keff = 1.5 and 2 for oxygen and Keff = 0.3 for iron, the expected concentrations were estimated for the present material. These are shown in Tables I and 11, along with the experimentally measured values. The calculated concentrations are based on a molten-zone length of 10 pct of the total melted length, whereas in the present experiments the molten zone was approximately 5 pct of the total melted length. The effect of zone length on solute redistribution is most pronounced after a large number of zone passes. Comparison with Pfann's published data8 for solute redistribution for various Keff's and zone lengths indicates only small differences at low numbers of completed zone passes. It is evident that the expected distribution has not been realized in the case of iron. Scrapings of material deposited on the inner surfaces of the electron-focusing cage were found to be magnetic. It is, therefore, concluded that redistribution of iron is masked by evaporation. Deposition of iron inside the focusing cage was observed at all rates of zone travel. The results of the investigation may be summarized as follows: 1) Segregation of oxygen is typical for a solute with a distribution coefficient, Keff > 1. 2) No redistribution of oxygen takes place at high rates of zone travel. 3) The distribution coefficient for oxygen lies between 1.5 and 2.0. 4) Purification with respect to iron occurs mainly by evaporation. 5) The focusing cage is effective in preventing tungsten contamination.

Jan 1, 1967

By D. L. Murphy

As the world's demand for iron ore increases and available sources are depleted, increasing attention will be centered on deposits in the Quebec and Labrador portions of the Labrador Trough. Improvements in the beneficiation of low grade iron ore stimulate exploration for deposits amenable to concentration. This study is centered on the Mt. Wright-Lake Carheil area, lying between Wabush Lake and Mt. Reed in Quebec. Described in detail are the general lithology, structural and economic geology, and mineralogy of the iron-formation. The iron ore province of Quebec and Baffin Island extends from the southern shore of Baffin Island southeasterly through the Labrador Trough to Matonipi Lake, approximately 185 miles northwest of Seven Islands. (See Fig. 1.) Future geologic field studies will very likely extend the limits of the province to include the ferruginous and associated rocks of the Lake Mistassini area. At present, only the deposits near Knob Lake and Lake Jeannine (Mt. Reed) have been brought into production although in the near future several other properties including those at Wabush Lake will commence operations. Within the next decade or so, as the world's demand for iron ore increases and available sources are depleted, this region will undoubtedly become a major mining district. Initial reports of iron-rich rocks in Labrador date back to the investigations undertaken by A. P. Low near the turn of the century. During the ensuing years the country was prospected chiefly for precious and nonferrous base metals because of its inaccessibility and the low tenor of the iron ore. In 1945 an evaluation of the direct shipping ores near Knob Lake indicated that sufficient reserves were present to justify the enormous capital expenditure required to bring the deposits into production. Initial open-pit mining began in 1954 following the construction of a townsite, a 360-mile long railway to Seven Islands, and an elaborate loading dock. Recent improvements in the beneficiation of low-grade iron ore have stimulated widespread exploration for deposits amenable to concentration, particularly along the southwest extension of the Trough. The Mt. Wright-Lake Carheil area, bounded by longitudes 66O45' and 67 30' west and latitudes 52 30' and 52 45' north, is a nearly rectangular tract of slightly less than 500 sq miles. It is in Saguenay County, 174 miles north-northwest of Seven Islands (see Fig. 1). Except for the periods of the spring breakup and the fall freeze up, the area is readily accessible by air.

Jan 1, 1962