Search Documents

By W. W. Dudley

Inflow of ground water is an important engineering and safety consideration during construction of large openings underground. The initial step in predicting groundwater inflow involves hydraulic tests in exploratory drill holes. Zones within the area of interest are isolated in the drill hole by inflatable packers and are tested by measuring the water level responses to applied hydraulic stresses. These responses may then be translated into significant hydraulic characteristics of the tested rocks such as transmissivity, hydraulic conductivity, hydraulic potential, and storage coefficient by using a type-curve solution. Once the geometry and necessary hydraulic characteristics have been determined for the rock in the vicinity of the proposed opening, a model can be developed using certain assumptions that will lend itself to treatment with available mathematical methods. The mathematical method applied to the model considers conditions of partial penetration and nonsteady-state, leakyartesian, constant-drawdown discharge of ground water. A type-curve solution results in a curve that gives the variation of discharge (inflow) with time. This technique of predicting ground-water inflow has been used in planning construction of cylindrical chambers for use in underground nuclear experiments by the U.S. Atomic Energy Commission. These chambers have been constructed in low-permeability rocks at depths as much as 6000 ft and under hydraulic heads of thousands of feet.

Jan 1, 1973

By R. B. Rosene, G. L. Foster, A. R. Hendrickson

he properties of some of the common fracturing oils, such as sand-falling rate, fluid loss and viscasity, are a function of the three major constituents of the oil. These are: asphaltic material, parafin waxes and a base oil. The base oil can be either high or low viscosity. Asphaltic material increases viscosity by thickening the oil, decreasing the rate of fall of sand through the oil. at temperatures up to 200" F. When large arnorrnts of parafin wax are present, much of the wax i.s not dissolved, but is present in the form of rnicroscopic crystals. 7'his, of course is limited to temperatures below the melting points of waxe.s. As a result, parafin waxes clo not function primarily as thickener.7, but rother as bullting materials. The functiori of wax, without asphaltic material, in a low viscosity base oil is uniquely unlike that of wax with asphalt coexistent in the oil. The resulting difierence in wax crystal size governs the sand-falling rate to a large extent. An ideal type of fracturing oil is one containing neither asphalt nor waxes. In such cases, the viscosity and resulting low sand-falling rate are apparently due to soluble resin- ous hydrocarbons, which are compatible with formation oils. INTRODUCTION Since the introduction of hydraulic fracturing as a method of stimulating production from oil and gas wells, a variety of fluids have been employed to open the fractures and carry the propping agent. Such fluids include gels, emulsions, and oils. In the latter category, the use of refined oils has increased tremendously, and it is probably safe to assume that such oils represent more than one-half of the total fluid used in fracturing. The general acceptance of refined oils for fracturing can be accounted for on the basis of their relatively low cost and general applicability. To minimize transportation costs, such refined oils are generally obtained within the local areas of operation. As a result there are several kinds of oil used in different areas, with a wide variation in the basic composition. These types may vary from a fair grade of lubricating stock to a highly viscous cut-back asphalt. or road oil. Originally, little attention was paid to the composition of the oils used for fracturing, and any oil which would carry sand was considered satisfactory. Recently, however, service companies and well operators have become more concerned with the type of oils used for fracturing. With this in mind, the present work was undertaken to evaluate and compare many widely used fracturing oils to determine which constituents were most desirable for fracturing purposes. Some of the important properties of fracturing fluids are sand-falling rate, viscosity, and fluid loss. Other properties, that are actually of no less importance, include flash point, pour point, emulsifying tendencies with formation brines, and compatability with the formation oils. This discussion has been limited, however, to the first mentioned properties in order to give some idea of the general composition of the refined oils, how they function, and why. PROPERTIES OF FRACTURING OILS The properties of fracturing oils are a function of the three major constituents of the oil. These may be designated as: (1) asphaltic material, (2) paraffin waxes and (3) a base oil, which may be of either high or low viscosity. The asphaltic material clas-

Jan 1, 1956

By Thiann R. Yu, William J. Quesnel

At Kidd Creek, the annual production of 4.5 million tonnes of ore has been achieved primarily with sublevel blasthole stoping. This mining method has allowed underground operations to meet the designed production capacity while maintaining an outstanding safety record. To achieve this goal, rock mechanics principles have been integrated into each facet of mining in the planning stage, in the production stage, and in various stages of ground support. This paper evaluates the two adopted mining sequences based on ground stress patterns, blasting control, ground reinforcement, backfill support, and numerical modelling for stope stability at the mines.

Jan 1, 1984

By Chris Mills

The role of gravity separation in the mineral industry is briefly considered in perspective. The mineralogical and laboratory approaches to gravity process design are examined with emphasis on process technology selection. The equipment available for small scale and pilot test-work is discussed, particularly in regard to scale-up and the acquisition of reliable, accurate data. Transposition of performance data from pilot scale to plant scale is explained. The available types of full scale gravity separation equipment are discussed with emphasis on large high-capacity units. Plant layout and selection of ancillary equipment are considered.

Jan 1, 1978

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

The 114th(New York) Meeting of the Institute will be held in the third week of February, 1917. The committee on Papers and Publications has set Dec. 1, 1916, as the closing date for the receipt of manuscripts intended for this meeting. . Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committees they must be sent to those committees enough in advance of the time to be forwarded and in the hands of the Secretary by the time specified.

Jan 10, 1916

By D. M. Given

HOW much can the mine operator afford to spend on his coal burning boiler plant? The usual answer is as little as possible and still get the job done. Thus, attention must be focused on the spot where excessive costs are most likely to arise - the materials handling end of the job. Boiler plants consuming less than 30,000 tons of coal annually can be controlled to the point where costs for handling coal and ashes are under $1.00 per ton. There is a wide selection of coal and ash-handling systems that can be used in smaller boiler plants to provide labor savings and convenience required if management is to accept coal as fuel.

Jan 7, 1953

By R. Hogg, D. W. Fuerstenau

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation, and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most clearly met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80% of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50% of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1973

By J. M. Ohm, C. M. Bunker

Two special tools for recovering gamma-ray probes and logging cable from drillholes have been designed by Ohm and Bunker and constructed by Ohm. Though intended specifically for U. S. Geological Survey equipment, they may be used with other equipment of the same general type. Fishing Tool for Probes: A fishing tool of the overshot type (Fig. 1) was designed to retrieve logging probes (sondes) that become disconnected from the logging cable and are trapped in the drillhole. When the tool slides over the top of the gamma-ray probe, studs on the bottom engage the shoulder near the top of the probe (Fig. 2), which is then pulled to surface. The barrel can be constructed from brass or steel tubing. Wall thickness is not a critical dimension, but the tool should be heavy enough to sink through mud or water in the drillhole. The internal length of the tool must be enough to prevent interference with the upper end of the probe head as the tool slides over it. The design of the probe head used by the USGS required a minimum free space of 2 1/2 in. inside the fishing tool, which was made 7 1/2 in. long to increase the weight. The lower end, which engages the shoulder of the upper end of the probe, contains three studs placed at 120" around the circumference of the tool and held in the engaging position by the tension of a spring wire. The studs can be made of any metal, such as steel, having high tensile strength. As the tool slides over the probe the studs are pushed outward from the center against the spring tension, allowing the tool to slide into position below the shoulder of the probe head. The spring tension forces the studs inward into the engaged position after they pass the shoulder. When the tool is raised the studs stop against the shoulder, preventing the tool from sliding up over the top of the probe. Once it engages the shoulder of the probe it cannot be freed until both probe and fishing equipment are recovered from the drillhole.

Jan 1, 1960

By J. W. Leomrd, B. A. Donahue

Results of research are presented examining the extent to which the analytical characteristics of the relatively distinct coal bands from a variety of coal seams can be related to each other. This paper dis-cusses an approach for developing a practical coal petrographic quality control program based on conventional analyses, most of which is part of the standard A.S.T.M. procedure. The work is a final follow-up to Part I of this series which was prepared by the authors as an approach to applying conventional coal petrography to single coal seams. Recent published work by the authors entitled Petrography for Coal Mining and Coal Prepration: Part I dealt with interrelating various chemical and physical properties of coal1 measured using conventional analyses made on distinct petrographic bands taken from single coal seams. Since most coal production facilities process coal from a single coal seam or from very closely related coal seams in the same area,2 emphasis on interrelating the properties within a single seam appeared appropriate. The distinct petrographic bands were analyzed on the assumption that such differentiated data would be more representative of a heterogeneous coal seam than the single analytical value commonly used to characterize each property of an entire seam.34 Effort was directed at demonstrating the extent to which the interrelated chemical and physical properties 5,6 could be developed into nomographs or petrographic standardization graphs. Thus, one analysis, determined on a series of petrographic fractions separated from a single sample, was used to estimate numerous other properties in each fraction by referring to the previously established petrographic standardization graphs. This conventional approach to coal petrography was undertaken as a suggested feasible means by which a few coal analyses could be employed to develope a more penetrating knowledge of the properties of coal from any given seam in order to monitor more extensively its performance at the point of utilization. Such procedures can support development of the type of in- formation commonly sought through automated testing and through the use of computers.7 The broad knowledge which can be developed through these procedures is intended for application in the generation of an analytical profile or broad characterization of coal. These estimates were not intended as replacements for individual coal analytical tests. In this expanded second part of the research program, distinct petrographic bands from nine coal seams in the Central Appalachian Region were physically and chemically analyzed to elucidate the extent to which this concept of conventional petrography could be broadened for application to numerous coal seams. In presenting this second phase of work, the relationships developed are presented individually and not in a connecting series of nomographs or petrographic standardization graphs as in the previous work, thus leaving open the combinations of possibilities to individual interpretation and application. MATERIAL AND EXPERIMENTAL WORK Nine coal seams, representing a wide range of rank, from the Central Appalachian coal fields were used in this study. The distinct petrographic bands from the Kittanning, Pond Creek, Jawbone, Tiller, Poca-hontas No. 3, No. 2 Gas, Eagle, Winifrede, and Pittsburgh coal seams were separated by carefully removing a portion of each band at the face of the seam. The following were determined: ash, sulfur, free swelling index, heating value, bulk specific gravity, volatile matter, Hardgrove Grindability Index, and Gieseler Plastometer measurements. Determinations, where procedures were available, were carried out using ASTM standard procedures.8 Bulk specific gravity was determined using a kerosene volume displacement procedure modified from a method applied by Headlee and McClelland of the West Virginia Geological survey,9 Those bands with a bulk specific gravity greater than 1.60, which is generally above the practical specific gravity cleaning range of bituminous coals, were excluded and no analyses were performed. Much of the initial organization of this second phase of work was developed through the extensive use of a computerized statistical monitoring program (see Ref. 4). However, in order to achieve the closest possible interpretation of results, the final organization of data proceeded mainly from exhaustive trial

Jan 1, 1968

By S. Terry, J. G. Munro

A unique feature of the recently dedicated pelletizing complex of Hamersley Iron Pty. Ltd. is the dry grinding circuit for the iron ore fines. This facility, located at Dampier, some 800 miles north of Perth, Western Australia, has a rated annual capacity of 2 million tpy of iron ore pellets. The Mt. Tom Price orebody, which supplies the pelletizing plant, is a massive deposit of high-grade hematite containing an estimated 500 million tons of ore averaging 64% iron. The main impurities are ferruginous shales that occur in bands of varying widths in the orebody. An average analysis shows 4.4% SiO2, 2.0% A12O3, 0.05% P and 1.8% LOI.

Jan 5, 1968

By G. C. Wallick

Since the appearance of the paper, "Solution of the Equations of Un-steady State Two-Phase Flow in Oil Reservoirs," by W. J. West, W. W. Garvin, and J. W. Sheldon,' a two-fold investigation of this subject has been carried out. One objective of the investigation has been to deter-mine the feasibility of solving such problems 7on a medium-size com-puter such as the Datatron*, and the other objective has been to in-vestigate the application of such cal-culations to experimental and theo-retical petroleum reservoir research. In the first Datatron calculations, the fluid and rock properties published by West, et al, were used, together with the published equations describ-ing the system. Details of the formu-lation not given in the original paper are discussed in the Appendix to this note. Reference should be made to the subject paper for the complete equations and defintion of symbols. An unexpected result of this in-vestigation was the discovery that the linear solution published by West was in error. Thus, in addition to describing the Datatron solutions and to discussing certain numerical diffi-culties which will be encountered if one uses the published method of solution, the purpose of this note is to indicate the nature of this error. LINEAR FLOW Since the linear case requires a minimum amount of scaling, a fixed-decimal point Datatron program was written for the one-dimensional flow problem and an attempt was made to duplicate the solution described by West. In the case described, fluid was produced at a constant rate, Q, until such time as well pressure reached 0.04. Production was then continued at constant pressure. From the constants and curves given by West it was determined that the ini-tial constant production rate could be approximated by Q = 0.007. An ini-tial dimensionless time step ?t = 0.434 X 10 - "as used, and each suc-cessive time step was doubled until a value of = 0.444 was reached. This constant interval was then used for the remainder of the solution. In subsequent solutions, several varia-tions in the time schedule were em-ployed, including smaller time steps and slower rates of increase in the time steps. In all cases, almost identical results were obtained regardless of the time schedule employed. However, as described below, it was noted that the time schedule had some influence on the rate of convergence of the solutions. As a check on the accuracy of the solution, the cumulative production at each time step was calculated using the two methods described in the Appendix. Satisfactory agreement was observed with the differences in these two values of the order of two parts in 50,000. It should be noted that the mass balance check as described is of questionable value, particularly with regard to the well pressure and saturation. This is especially true in the radial solution where pressure and saturation values near the wellbore would make only a negligible contribution to the numer-ical integration. It is believed, how-ever, that such a comparison is ot value in determining the over-all accuracy of a solution. In comparing the Datatron solu-tion with that published by West it was discovered that in the later stages of depletion, the pressures near the well declined more rapidly in our solution than in the West solution, and that the limiting well pressure of 0.04 was reached at an earlier time than that originally reported. It thus became evident that it would be impossible to duplicate the production schedule described by West and a constant rate of production was maintained until the well pressure was equal to 0.0. A representative comparison of the results published by West with those obtained in this investigation is shown in Fig. 1, which is a plot of GOR as a function of cumulative recovery. These two curves should be in agreement until a cumulative recovery is reached which corresponds to a well pressure of 0.04 — for the Datatron solution, a recovery of approximately 5.6 per cent. Actually, a major disagreement is evident. Subsequent correspondence

Jan 1, 1958

By H. D. Merchant

NUMEROUS publications have examined hot hardness of metals and alloys. Some have studied creep in long-time hardness tests, few of which, however, were tested under a spherical indentor. 1-3 The results of Mulhearn and Tabor' indicate a parabolic-type creep for indium and lead, whereas Moore and Tabor2 how a logarithmic-type creep for indium. Similar semilog relationships between hardness and time have been found by Goffard and wheeler3 for magnesium, aluminum, and their alloys. In this note, the elevated-temperature hardness of some complex alloys, shown in Table I, was examined to discover whether any basic information about the deformation behavior of the alloys could be obtained. One of the alloys, H-13 alloy steel, was tested for short-time creep tests to examine the hardness-time relationship at various temperatures. A standard Brinell Hardness Tester, mounted with an appropriate furnace and 99 pct A12O3 poly-crystalline indentor, was employed for the purpose. The alloys were tested at temperatures from room to 1400°F for 30 sec under 1500-kg load. The creep studies were conducted for about 8500 sec at 7l°, 500°, 1000°, and 1200°F. For constants A and B, a relationship of the type H = Aexp(-BT) [ll was obtained for all alloys between hardness, H, and temperature, T. In the semilogarithmic plot, the data points for each alloy were arranged into two groups, each group on a straight line with a specific set of A and B values. These results are in agreement with many such observations on hot hardness, notably those of Westbrook for pure metals,4 The thermal softening coefficient, B, and transition temperature, Tt, for various alloys are shown in Table I. The change in slope around the transition temperature suggests an apparent change in the mechanism of deformation, probably from the shear (below Tt) to the diffusion type of mechanism. At the temperatures above Tt, for constants A' and B, a relationship of the type was obtained between H and T, Fig. 1. The nature of the equation, where R is gas constant, suggests the possibility of a thermally activated mechanism of deformation above Tt. The constant B' may hence be defined as the apparent activation energy of indentation. The B' values of various alloys are shown in Table I. A plot of B vs B' gives a curvilinear relation shown in Fig. 2. The indentation-creep data for H-13 alloy steel is shown in Fig. 3. At 71" and 500°F, the creep initially follows the logarithmic time law. However, the indentation size stabilizes after 7 sec at 71°F, and after 10 sec at 500°F. Further increase in loading time has no effect on indentation size. The creep of 1000° and 1200°F follows the logarithmic time law for the first 1000 sec, after which the

Jan 1, 1964

By G. W. R. Kuzyk, John D. Smith

Tantalum Mining Corporation of Canada Limited has been mining tantalum ore from the Bernic Lake pegmatite dyke since 1968. The shallow nature of the dyke and relatively high strengths of the various rock types led to the choice of a room and pillar mining method. Rock mechanic studies have indicated that the original pillar dimensions of 50 feet x 50 feet are conservative for existing rooms. Therefore, a plan to reduce the size of pillars using rock mechanics instrumentation to monitor the resulting stress on pillar remnants and stope backs was devised. The paper describes the test work done on the rock types within the pegmatite dyke. The use of Irad stress cells and extensometers in monitoring the stress in pillars is described. The actual results of the program to date are presented.

Jan 1, 1983

By Charles F. Johnson

A pulse technique is described for the measurement of bar velocity. A low frequency sine wave pulse is used which allows the wave-length to become much larger than the lateral dimensions of the test specimen. The low frequency pulse method has been tested and compared with the resonant frequency method and the results show that both methods give, on the average, equivalent velocities.

Jan 1, 1971

By Harry Bapty

LONGHOLE drilling with a heavy type percussion Leyner drill, jointed steel rods, and a tungsten carbide insert bit was investigated while drilling and working a quartz barite brecciated rock. Procedure and practice were developed and its suitability for tackling pillar and sill recovery proven and extended to regular stoping at Torbrit. Torbrit, as the name implies, is a contraction of the Toric property and the Britannia Mining & Smelting Co. Ltd., the former owners. This silver property, with minor amounts of lead, zinc, and rarer sulphides of little or no economic value, was discovered in 1916 from an outcrop in the Kitsault River, 18 miles north of Alice Arm Post Office, in the Portland Canal Mining District, B. C.

Jan 11, 1954

By N. G. Johnson

ALL of us are only too familiar with the fact that first the defense program, and finally the war, required vastly increased production from existing sources, and the discovery and development of new sources of minerals and metals. For this vast program, the explosives industry was well prepared. I use the term "well prepared" to cover all the phases of explosives service, which include formulation, design, manufacture, distribution, and application.

Jan 1, 1944

By Manuel Valerio Ortega

This Mexican amalgamation-process, invented in 1557, at Pachuca, by Bartolome de Medina, has been widely discussed in America and Europe, but thus far there is no universal agreement as to all the chemical reactions involved. Having been, after many trials, the first to succeed in effecting the amalgamation of silver-ores by the same mechanical means, but doing without one of the chemical substances which had been considered indispensable in the practice of 300 Sears, I am led to offer these notes as a contribution to the discovery of an exact theory concerning the patio process. My treatment for silver- and gold-ores being protected by letters-patent in this country, the United States, France, Peru, Bolivia and Chile, I may speak freely concerning its materials and manipulation. I. Patio-Amalgamation. The ore extracted from the mine is sorted by pepenadores, who break the large pieces with hammers, rejecting those which contain no ore, set aside the very rich to be smelted, and deliver the rest to be crushed and pulverized for direct amalgamation in the patio. The broken lumps, of about fist-size, are first ground in Chilean mills, and then reduced, in arrastras or tahonas, to fine slime. After the lama or slime has acquired a suitable consistency by the evaporation, through the sun's heat, of a part of the water which it contained, it is spread upon the patio or amalgamating-floor, where it is mixed with 5 or 6 per cent. of common salt. The next day a certain amount (depending upon

Jan 1, 1902

By Charles B. Dudley

It is evident that, as the size and weight of cars have increased, the demands on the cast-iron car-wheel have become more and more severe. Fortunately, the factor of safety in the cast-iron wheel, as originally made, was so large that it was only when freight-cars approached the capacity of from 80,000 to 100,000 lb. that the question of wheels began to give some anxiety. A moment's thought will show that, as freight- and passenger-cars have increased in weight and size, a much greater duty is required of the same eight wheels than was formerly the case. In other words, although the cars have increased in capacity from 15 tons to 50 tons each, the number of wheels under a car has not been generally increased. It is true, some cars have been equipped with 12 wheels, but this construction is not the rule. Hence the duty which the wheel must perform has become much more severe, and although it was clearly able to stand some increase, there must evidently be a limit somewhere which cannot be exceeded. Meanwhile, it is the part of wisdom to make better wheels if possible, and accordingly, no little study is now being devoted to the requirements for cast-iron car-wheels; and modifications are being made, both by increasing the weight of the wheel and by improving the quality of the metal of which it is made. The desire to improve the quality of the wheel has led to the preparation of specifications for its manufacture; and within the last 15 years a more rigid scrutiny of the wheel is char-

Jan 1, 1905