Search Documents

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of June, 1913: Members. ANGERER, VICTOR, Vice-Prest. and Genl. Mgr., Wm. Wharton, Jr. &, Co., Inc., 25th St. and Washington Ave., Philadelphia, Pa. BULLOCK, ALLYN, Min. Engr., Hazleton, Pa. CUNNINGHAM, NOEL Met. Engr. Hollinger Gold Mines Ltd., Timmins, Ont Canada ESTABROOK, EDWARD L., Supt. of Colliery 426 Center St., Ashland, PA. GATES A. O. Instructor Purdue Univ. La Fayette Ind. 1 LUDLUM, ALBERT C., Prest., New York Engrg. Co., ,2 Rector St., New York, N. Y. MILLER, HERBERT F., Met. Engr P. O. Box 142, Verona, Pa. MORTON, ELMER T., Min. Engr Clifton, Ariz. MURFIT, RICHARD H.. Fdv. Asst Hess Steel Castings Co., Bridgeton, N.J. QUAYLE, THEODORE W., Chief Sampler, Metcalf Mines, Arizona Copper Co., Metcalf, Ariz.

Jan 7, 1913

Jan 1, 1907

By J. H. Anderson, G. A. Parks, B. K. Jindal

Both temperature and humidity are important variables in electrical separations. By independent control of temperature and water vapor pressure, it is shown that charge depends primarily upon relative humidity, not on temperature or water pressure alone. All the effects of temperature changes other than modification of humidity are apparently small. However, humidity control can be achieved through manipulation of the more tractable variable, temperature. Both temperature and humidity are important variables in electrical separations. Some of their effects have been described in general by Fraas1,2 and by Ralston.3 The influence of temperature and humidity may be considered a problem in industrial separations because humidity, especially, is not normally controlled, hence leads to unpredicted quality control problems. The problem is significant whether the separation is based on conductivity differences or on contact electrification. There is no doubt that water adsorbs from humid atmospheres onto mineral surfaces resulting in conductivity changes.'-8 An empirical relationship between conductivity and humidity is1.4-6,8 where a and b are constants peculiar to the substrate, and s and h are the conductivity and relative humidity respectively. Some authors have taken advantage of differences in a and b among minerals to make or propose electrodynamic separations in which h is the key control variable. Fraasl,2 reported that the charge developed on quartz and feldspar through contact with aluminum is sensitive to humidity, as illustrated schematically in Fig. 1. Lawver9 found that the charge developed by quartz on contact with several materials was tem-

Jan 1, 1967

NEW MEMBERS The following list comprises the names f those persons who became members during the period of Dec. 10, 1917, to Jan. 10, 1918. ARLUCK,- A. A., Headquarters Co., 66th Artillery Brigade, 41st Division, Care Postmaster, New York, N. Y. BUCK, LEONARD J Park & Prospect Ave., Bethlehem, Pa. BULL, FREEMAN N., Min. Engr., Robert W. Hunt & Co., 310 Wall St., Joplin, MO. BURGESS, ELISHA PAYNE JEWETT, Pres. & Mgr., Montana Consolidated Copper Co., Care Clark Dodge & Co., 51 Wall St., New York, -N. Y. CAMPBELL, THOMAS E Governor of Arizona, State House, Phoenix, Ariz. CARTWRIGHT, F. 0., Asst. Chief Clerk, The Braden Copper Co., Bancagua, Chile. CASH, FRANK E., Engr. & Asst. Supt. of Mines, Alleghany Ore & Iron Co., Lignite, Botetourt Co., Va. CRITCHLOW, EDWARD B., Pres., Conkling Min. Co., 307 McCormick Bldg., Salt Lake City, Utah.

Jan 2, 1918

By J. L. Huitt, D. K. Lowe

This laboratory flow study covers propping agent transporl in horizontal fractures as influenced by the characteristics of the propping particles, fluid and fracture. Correlations are presented for the transport of particles, deposition and fingering through dunes. For particles moving individually, the article velocity in some cases may be low compared to the hulk average fluid velocity; in other cases, the particle velocity may exceed the bulk average fluid velocity. At high propping agent concentration or low fluid velocity, the likelihood of particle deposition and dune formation increases. Fingering and channeling accompany dune formation. Dune formation can be limited to the outer region of tile fracture by adjustment of pump rate, fluid viscosity and particle concentration. A method is presented by which pump rate and fluid vircosity may he selected to control dune formation for given propping agent concentrations. INTRODUCTION The area and flow capacity of a fracture predominantly control the stimulation derived from hydraulic fracturing. Generation of fracture area exposes the rock matrix to a flow channel; the flow capacity of the fracture controls the flow through the channel to the wellbore under a given pressure gradient. This paper pertains to an important factor that affects the flow capacity of a fracture: the transport of the propping particles in the fracturing during the hydraulic fracturing treatment. With a better understanding of particle transport, fracturing treatments may be designed to obtain more effective distribution of the propping agent. RELATED STUDIES In recent years, the approach to obtaining high fracture flow capacity has been partial monolayer propping. Three papers1-3 have dealt with various facets of this concept. However, in some papers dealing specifically with particle transport, the results generally indicate that packing the propping particles within a fracture is inevitable. In early work&apos; with a sand slurry flowing in a pie-shaped flow cell, qualitative results showed that particle deposition in a fracture during transport should be expected. In other studies"" correlations based on slurry flow in vertical linear flow cells showed particle deposition was primarily a function of fluid velocity. In a recent paper the rate of sand advance (movement of dunes) in a horizontal linear flow cell was discussed. Subsequently, a method was given for designing fracturing treatments, based on the extent of sand advance during a treatment. In this work, particles whose diameter was small relative to the fracture width (i.e., dl W< 0.2) were primarily considered. The particle transport approaches that of sand transport in a stream bed. The industry trend, however, has been to use larger size propping agents. That is, particles with diameters approaching fracture widths predicted by Perkins and Kern.&apos;&apos; This trend has led to generally better fracturing treatments with particle relative sizes in the range 0.2 <d/W < 1.0. In all of the particle transport studies previously cited, the fluid characteristics were discussed. However, little or no attention was given to the parzicle characteristics. In this study the particles. as well as the fluid and fracture, are considered. VARIABLES AFFECTING PARTICLE TRANSPORT In the exploratory work to set LIP a program for this study, it was noted that particles within a batch moved at different velocities in a horizontal linear flow cell. In some cases the particles moved independently. In others there was particle interference. Also, particle deposition and fluid fingering occurred in some cases (Fig. 1). As a result of observing the easily distinguishab&apos;le types of particle movement, the particle variables as well as the fluid variables were included. In addition, the fracture width was included because the fluid velocity profile surely must affect the movement of the larger particles differently than that of smaller particles. Particle variables were density, diameter (based on a sphere of equal volumetric displacement), long and short dimensions, drag coefficient and velocity. Fluid variables were density, viscosity, yield shear strength and velocity. Fracture variables were the width and the angle between the plane of flow and a horizontal plane. Two factors which may prove to be important were omitted because of the complexity resulting from the parameters cited above. These are the fracture-surface roughness and gross irregularities that cause changes in the direction of flow. EXPERIMENTAL EQUIPMENT AND PROCEDURE A linear parallel-plate flow cell (Fig. 2) was used in the study. Lucite plates 1 in. thick formed the test section and permitted a viewing section 11 ft long and 10 in. wide. Spacing between the plates was adjusted with shims to give fracture widths 1/36 to 1/2 in. The model could be tilted to an angle of 45" with the horizonltal plane. Fluid flow was maintained with a Moyno positive displacement pump. Single particles were placed in the flow stream with a particle injector. A .4 - in. diameter plunger moving at a constant rate in a

Jan 1, 1967

By A. Ghosh, T. B. King

The kinetics of the discharge reaction: 20&apos;- (in silicate melt) = O,(g) + 4e- at a platinum anode in lithium silicate melts have been studied al 1350°C by galvanostatic methods. Plots of the sleady-state overpotential, q, as a function of the logarithm of the current density, i, showed injlections and were linear only at high current densities. The value of the overpotential was influenced by bubbling gas through the electrolyte. The ocer potential was also studied as a function of time. The rise and decay of overpotential were very slow processes. At low current densities transport is the likely rate-controlling process but at high current densities passivation of the electrode, Presumably by an oxide film on the surface, seems to be a contributory functor. IT is well-established that molten silicates behave as electrolytes&apos;5 and, except in a few cases,6 conduction is entirely ionic. Moreover, it is supposed that a possible, and perhaps predominant, mechanism for phase boundary reactions between metals and slags is similar to that in corrosion whereby anodic and cathodic processes occur at unrelated sites, the metal serving to conduct electrons.1&apos;8 Thus electrochemical studies of some slag-metal reactions would seem to be a useful way to diagnose the rate-controlling steps in the overall reaction. The electrochemical method is, in principle, a better diagnostic tool than the direct chemical method for the following reasons: 1) The partial electrochemical reactions, which are simpler than the overall reaction, may be studied individually. 2) The rate of reaction can be controlled at will and independently of the concentrations of reactants. 3) Fast reactions can be studied by relaxation methods.&apos; Esin and his coworkers5&apos;10"12 have pioneered such studies in silicates and have deviloped some ingenious techniques. Not all of their findings, however. can be accepted without a good deal of further work. In this investigation, the kinetics of the oxygen discharge reaction: 202- (in silicate melt) = Oz(g) + 4e- [I] at a platinum electrode were studied by both steady-state and transient galvanostatic techniques. Interest in this reaction was first developed as a result of the findings of Fulton and chipman13 that the reduction of silica, in a silicate slag, by carbon, dissolved in liquid iron, is a very slow reaction. Subsequent work, for example, by Rawling and ~lliott,&apos;~ has demonstrated that the reaction under these conditions must be slow, because the rate is limited by diffusion of oxygen in the iron to the metal-crucible phase boundary at which a CO bubble may be nucleated. Further work by Tarassof,&apos;~ in which the reduction of silica by aluminum dissolved in copper was studied, has shown that under these conditions, where carbon monoxide evolution is not involved, control of the reaction rate resides in diffusion of silica in the slag phase. However, there is no practical way of inducing sufficient convection in the system to make it clear that the phase boundary reaction is indeed fast. The overall reaction of silica reduction involves the discharge of silicon ions at cathodic sites and oxygen ions at anodic sites. In the examples cited, the discharged ions are dissolved in a liquid metal. In the present study of oxygen ion discharge, gaseous oxygen may be evolved at high current densities or oxygen may simply dissolve, possibly as oxygen molecules, in the silicate at very low current densities. The discharge of an oxygen ion at an anode must, in silicates less basic than the orthosilicate composition, be preceded by a reaction in the vicinity of the electrode, such as: which makes oxygen ions available. Platinum was chosen as the working electrode since it is comparatively inert to oxygen and is, therefore, expected to come rapidly into equilibrium with the electrolyte and with gaseous oxygen. Minenko, Petrov, and Ivanova16 have measured the electromotive force at a platinum electrode in molten silicates as a function of the partial pressure of oxygen in the atmosphere, the concentration of oxide ions in the melt, and the temperature. They found platinum to behave as a reversible oxygen electrode. At two different oxygen pressures, Po2 (I) and Pq (11). the electromotive force is given by: where F is the Faraday constant, equal to 23,060 cal per v equivalent, indicating that the electrode reaction is as written in Eq. [I.]. Platinum has been similarly used in molten silicates by other inve~ti~ators. "&apos;~~ In this investigation platinum was used only as an anode, since a current deposits other elements on its surface and changes its characteristics.

Jan 1, 1970

By H. R. Wenk

This paper describes a workshop on deformation mechanisms and texture development in rocks. Empahsis is on relating macroscopic mechanical properties with microscopic structures and the methods of their quantitative analysis.

Jan 1, 1982

By F. Claisse, R. Angers

Self-diffusion in iron has been measured during rapid a-r transformations using a variant of the Kryukou and Zhukhovitskii diffusion method. The study was performed by thermally cycling iron foils (1 to 6 cpm) through the transformation (=910°C). Some foils have been subjected to over 1000 cycles and some have spent more than 15 pct of their total diffusion time in the process of transformation. The experimental results show that the a-r transformation has no measurable effect on self-diffusion in iron. The study is completed by a quantitative analysis of mechanisms which can affect the diffusion rate during the transformation. The analysis confirms the experimental results. SINCE diffusion is an important factor in many solid-state transformations, it is of interest to study how it is affected by the stresses generated during these transformations. Clinard and Sherby1&apos;2 were the first to make a study along these lines. They measured diffusion coefficients in Fe-FeCoV couples subjected to slow thermal cycling (1.5 cph) through the a-r transformation range. They found an enhancement of diffusion by a factor of about two. The purpose of the present paper is to report measurements of the self-diffusion coefficient of iron during much more rapid thermal cyclings (1 to 6 cpm) through the a-r transformation (-910°C). These more rapid cyclings produce higher strain rates during the transformation and should emphasize any possible influence of transformation upon diffusion. EXPERIMENTAL Iron foils, 25 to 35 µ thick, were cold-rolled from 99.92 pct pure iron and annealed in pure helium for 2 hr at 870°C; the resulting grain diameter was about 150 µ. Specimens 0.5 by 8 cm were cut from the foils and I7e55 was vapor deposited on one of their surfaces. A 38 gage alumel-chrome1 thermocouple was spot welded in the middle of one of the specimen long edges, Fig. 1. Two 38 gage chrome1 wires were also spot welded along the same edge on each side of the thermocouple; they were placed 2.5 cm apart and used for electrical resistance measurements. In order to prevent twisting and crumpling, the specimens were pinched between two quartz plates 0.1 by 1 by 7 cm and the assembly was close fitted into a 1 cm ID quartz tube. Four holes were drilled through the tube to let the 38 gage wires out: these were connected to the recording equipment by means of extension wires. 20-gage nickel wires fixed at both ends of the specimens were used to thermally cycle the foils by Joule heating. The above described device was placed in a 2.7 cm ID quartz tube which in turn was placed in a tubular furnace. Either a pure helium atmosphere or circulating hydrogen was used during the experiments. Specimens were subjected to thermal cycles between a minimum temperature To and a maximum temperature Tm at rates ranging from 1 to 6 cpm. This was obtained by maintaining the furnace at a constant temperature near the minimum temperature To and periodically passing an electric current through the specimen. Cooling was achieved by heat losses to the surroundings. The forms and periods of cycles were varied from one specimen to another; however, each specimen was subjected to one type of cycle only. The temperature and electrical resistance variations of the specimens were recorded as a function of time. The temperature curves were used for diffusion calculations while the electrical resistance curves were used to monitor the transformation and to determine its starting point and its approximate duration. Diffusion was measured by the method developed by Kryukov and zhukhovitskii3 and modified by Angers and Claisse.4,5 In this method a metallic foil is coated on one side with a radioactive isotope and the activity is measured periodically on both sides during the diffusion anneal. The following equation then holds: where: I1 Activity on the surface on which the deposit is made. I, Activity on the opposite surface. t Diffusion time. B Constant. D Diffusion coefficient. d Foil thickness including the deposit. G(t) A function of time; it is a second order correction term which is given graphically in Refs. 4 and 5. The diffusion coefficient D is found by plotting ln[(Il - I2)/(I1 + I,)] -G(t) against t; the resulting slope m leads to an accurate calculation of D through Eq. [2]. The effect of the a-r transformation on diffusion is expressed by the ratio DT/DU where:

Jan 1, 1970

By Fathi Habashi

Chalcopyrite can be readily leached with HNO3, but the recovery of elemental sulfur does not exceed 50% under the most favorable conditions. Preheating at 500°C in a slightly reducing atmosphere increases the recovery of elemental sulfur to about 65%. Chalcopyrite can also be treated with HNO3 in a pressure reactor at 110°C to solubilize selectively the copper while iron remains in the residue as an oxide. The recovery of elemental sulfur also improved when preheated chalcopyrite is treated in this way. Stainless steel should be an adequate material of construction.

Jan 1, 1974

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper discusses the results of the Fry conventional or cocurrent in situ combustion test, which was conduct-ed in a 3.3-acre inverted five-spot. The depth of the formation was between 880 and 936 ft; the oil had a specific gravity of 28.6° APl and a viscosity of about 40 cp at the reservoir temperature of 65°F. Preceding the combustion test, air injection tests were conducted which, in conjunction with geological studies, were used to evaluate the characteristics of the reservoir. Combustion was initiated on Oct. 13, 1961, with ignition being accomplished by a 40 kw electrical heater. The test phase of the project ended on Oct. 1, 1963. During the test, the average air injection rate was 1,520.-000 scf/D. Throughout the test, production of all fluids— gas, oil, and water—was monitored. Cumulative oil production credited to the project was 100,586 bbl. The cumulative air-oil ratio was 11,500 scf/bbl oil, and the oxygen uti1ization efficiency was 87 per cent. INTRODUCTION The Marathon Oil Co. conducted a successful in situ combustion test, beginning Aug. 22, 1961, at the Fry unit, Crawford County, 111. The purpose of the project was to test the feasibility of cocurrent in situ combustion as a means of oil recovery in the Fry type reservoir. Interest in in situ combulstion as an oil recovery tool has been stimulated mostly by the existence of large reserves of heavy viscous crudes with low expected recovery, usually less than 10 per cent. These are the so-called unrecoverable reserves, and most combustion tests to date have been conducted in this type of reservoir.1-4 In contrast, the Fry combustion test was conducted in a reservoir with a relatively high gravity oil having a relatively low viscosity. This paper discusses the performance of the test. The geology of the reservoir and the field operations are discussed in separate papers.5 TEST SITE The Fry combustion test was carried out in a 3.3-acre inverted five-spot portion of a lenticular body of Robinson sandstone. Net sand was 50 ft thick, porosity averaged 19.7 per cent, oil saturation was 68 per cent of pore volume, and water saturation was 20 per cent of pore volume. The oil in place was estimated at 1,040 bbl/acre-foot, or 171,600 bbl within the 3.3-acre pattern. The water in place was 326 bbl/acre-foot, or 53,800 bbl. The oil has a specific gravity of 28.7° API and a viscosity of 40 cp at the reservoir temperature of 65°F. AIR INJECTION PERFORMANCE Air injection took place in two phases, the phases separated by ignition of the reservoir. In the pre-ignition phase, air injection tests were conducted in the summers of 1960 and 1961. These indicated that the Fry reservoir was confined, and a high return rate of injected air could be expected. This proved to be an outstanding characteristic of the project, as cumulative gas production was 95.3 per cent of the air injected. The difference between the cumulative air injected and the total gas produced can be largely accounted for by the quantity of air stored in the reservoir. An estimated 16 X 10 cf of air remained in the burned-out portion of the reservoir and an indeterminate amount of gas was stored in the unburned but pressurized reservoir. Hence, a complete material balance of gases would account for nearly 100 per cent of the air injected. At times during the test, the daily gas production rate was 98 per cent of the daily air injection rate. Fig. 1 presents the air injection history of the Fry com-

Jan 1, 1966

By T. A. Rickard

The mountains of the picturesque Dauphine, in southeastern France, have long been known to collectors as the source of many minerals of rare occurrence; but. they contain also several mines, which, though less known, date from the time of the Saracens, many centuries back, to that of the graduate from the Ecole des Mines. In the department of the Isere, upon the cliffs of Villard Ey-

Jan 1, 1893

By P. Schwarzkopf, J. H. Brophy, J. Wulff

A constitutional diagram has been proposed for the tantalum-rhenium alloy system. Rhenium dissolved in tantalum up to 48 wt pct, and the maximum solubility of tantalum in rhenium is 5 wt pct. Intermediate x and s phases were found. X-ray diffraction, metallography and melting points were employed. SEVERAL investigators have described the phases present in the tantalum-rhenium alloy system, but no detailed account of the phase diagram prior to the present investigation appears to be available. Greenfield and Beck&apos; reported the solubility of 48 to 54 at. pct Re in tantalum, a s phase at 41 at. pct Ta, and x phase isomorphous with a Mn from 37 at. pct Ta to less than 25 at. pct. They employed as-arc melted specimens and heat treatments at 1200 °C lasting 72 hr.2 Duwez3 reported the existence of a a phase at the composition Re3Ta2. Niemiec and Trzebiatowski4 observed a lattice parameter a = 9.69A, for the x phase at a composition Ta7Re22, but no s phase. Savitiski and Tylkina5 have shown a hardness maximum at the composition 40 at, pct Ta and a somewhat lower plateau from 35 to 10 at. pct. Knapton6 indicated results similar to those of Greenfield and Beck.&apos; The present investigation describes the phase relationships in the tantalum-rhenium alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURE Commercial 99.7 pct Ta powder from Fansteel Metallurgical Corp. and 99.9 pct Re powder from Chase Brass and Copper Co. were used for alloy preparation. The powders were weighed to desired nominal compositions and then pressed without binder into compacts weighing 5 or 10 g. The compacts were arc-melted six times on alternate sides on a water-cooled copper hearth using a nonconsumable tungsten electrode in an atmosphere of titanium gettered helium, at a pressure of 500 mm Hg. In most cases this procedure yielded alloy buttons of satisfactory homogeneity. A series of alloy specimens were analyzed wet chemically for use as standards for X-ray fluorescence. All specimens were analyzed by fluorescence and the results showed that the compositions differed by less than 3 pct Re from the original as-weighed nominal composition.* On the basis of self-

Jan 1, 1961

By G. W. Tracy

The material balance equation has been used for many years by engineers to determine reservoir performance. The use of this equation in general has been twofold: first, to determine the oil-in-place in a reservoir; and second, to predict the future performance. The Schilthuis form of the material balance equation, or one equivalent to it, has been used by many of the engineers. The use of the Schilthuis form in predicting future performance has proved to be laborious in that one generally must make several estimates at each step of the trial and error calculation before arriving at a check of the oil-in-place. A method is presented for expediting the calculations. The Schilthuis form of the material balance has been rearranged into a more useable form. In using the material balance to predict the future performance of a reservoir, it has become common practice to estimate the incremental oil production for each step of the calculation which corresponds to a given pressure reduction. Instead of estimating the incremental oil production, the method outlined in this paper better lends itself to estimating the instantaneous gas-oil ratio. A check of oil-in-place is more easily accomplished by estimating gas-oil ratio since it is less sensitive to small inaccuracies. This method incorporates the same self-checking feature inherent in the Schilthius form. DEVELOPMENT OF SIMPLIFlED EQUATION In the development of the simplified equation, the Schilthuis form of the material balance equation will he used. Substituting in Equation 1 for and rearranging terms In Equation 2, the cumulative oil production (n) is multiplied by a factor which is uniquely a function of pressure. Also, the cumulative gas production (G) and net water influx are also multiplied by factors which are a function of pressure alone. These factors are called and are defined as follows: Using these factors, Equation 2 becomes The equation in this form is easier to manipulate mathematically than any of the previous forms which, have been used. Sources of data for the pressure factors are a bottom-hole fluid analysis and the ratio of initial gas cap volume to oil volume in the reservoir. AID IN DETERMlNING THE ORIGINAL OIL-IN-PLACE Each of the curves and +, have a similar shape. Each is infinite at the bubble point pressure. As lhe pressure is reduced below the bubble point, the

Jan 1, 1956

By K. Thirumalai, D. P. Schlick

Longwall Technology has a potential of resulting in safety and productivity improvements of U.S. underground coal mining similar to those experienced by the introduction of continuous miner systems. The study presents a comprehensive national evaluation of longwall technology to assess the potential of longwalls to improve health and safety and coal productivity. The study was conducted by the authors during the spring of 1980 as part of MSHA New Technology Coordination activities and with a view to examine the factors that may limit the acceptance of longwall technology in the U.S. coal mining operations. The study points out areas where adjustments need to be made in MSHA regulations and enforcement to help Longwalls. A two-entry longwall system appears to offer a practical method of improving underground coal productivity and safety. Applying regulations that are primarily designed for room and pillar methods to longwall mining, in some instances, reduces the effectiveness and productivity benefits feasible by new technology application. Controlling dust is the single predominant problem in the design and operation of longwalls in the United States. The results of this study points out a need for a coordinated program between government and industries on dust control technologies for examining acceptable technological options to control dust in longwalls without restraining the production capability of the system.

Jan 1, 1981

By HAROLD A. TITCOMB

TOWARD the close of 1925, a British geologist, T. Landell Mills, brought to the notice of .A. Chester Beatty and selection Trust Ltd. certain mineral areas in southern Yugoslavia. Mills&apos; data, which included rough maps and preliminary reports by&apos; a Yugoslav engineer, Jules Draskocy, appeared interesting to Reatty, and early in 1926, I, with three British assistants, proceeded to Serbiaand commenced the investigation of several groups of ancient mine workings. They were found to be extensive and the geological conditions-schists, limestones, and andesitic intrusive-favorable for mineral deposits. At Stan Trg, on the Trepca Concession, five rniles east of Kosovska Mitrovica, an ancient filled adit was found, a shelter-hut erected, and work started in reopening this adit.

Jan 1, 1936

By S. R. Rao

Interaction of potassium amyl xanthate with pyrrhotite has been studied thermochemically. Heats of adsorption of xanthate on unactivated mineral and the mineral activated with cupric ions have been compared with heats of reactions between potassium amyl xanthate and ferrous and cupric salts. It is shown that xanthate is consumed by stoichiometric exchange with anions present at the mineral surface. The floatability of the unactivated mineral is poor since xanthate is precipitated in bulk without creating a hydrophobic surface on the mineral. At the activated mineral surface, xanthate is adsorbed in certain isolated patches (active spots) and thereby creates a hydrophobic surface. The hydrophobicity of the mineral is greatly improved by lowering the pH to 4.5.

Jan 1, 1972

Since the beginning of the 20th century the world has been trying to find a new political system, even as it did at the end of the 18th century. The French Revolution instigated the destruction of absolute monarchies when Napoleon unwittingly showed the masses the advantages of freedom, as opposed to the abuses of unlimited power by the imperialists. In spite of advances in culture, science, and technology during the past 50 years, there is a hangover of laissez-faire economic principles. Failure to divert the trends of minority pressure groups has caused two world wars and is the basis for the current social unrest and turmoil. In the ebullition of ideas there have risen to the surface the dregs of ideas, old and new-Nazism, Fascism, Russian Communism-a hodgepodge of imperialistic, socialistic, communistic and capitalistic maneuverings where state monopoly of capital enables ruthless exploitation of the masses. The United States owes much of its industrial greatness to the work of pioneers in the mineral industries. The task of the pioneer was to locate and develop in a rude way the mineral resources of the nation. Today, mineral industries leaders are still in great demand, but for a different purpose-to direct intelligent utilization of the limited, waning, submarginal mineral resources. Today the need is for trained earth scientists, mineral

Jan 1, 1950

By Paul Tyler

THE extensive employment of nonmetallic minerals antedates the use of metals, but only within the last two decades has the production of nonmetals begun actually to keep pace with the complicated activities which characterize the so-called Machine Age. The economic changes ushered in by the Industrial Revolution were reflected first in an increased demand for metals and for fuels. In the modern sense, therefore, the nonmetallic mineral industries are new and afford new opportunities for engineer and economist alike. A certain amount of caution is indicated, therefore, before attempting to apply ready-made formulas to the problems of these industries. Economics is not an exact science. In the field of production technology where the number of variables is fairly well known, the principles of economics are readily applicable, but as the student proceeds through the province of marketing into the unexplored regions of psychology and sociology he must distinguish carefully between scientific reasoning and purely metaphysical speculation, even when the latter masquerades as economics. The present paper attempts to prove no preconceived theorems and is designed primarily to stimulate careful thinking on sundry neglected phases of these industries. An attempt is made to differentiate the general problems into single aspects which afford promise of being comprehended separately; also, some fundamental statistical data are presented, but merely to indicate a method of scientific approach applicable to more intensive studies.

Jan 1, 1933

The Ashanti mine is located in the Gold Coast region of West Africa in Ghana, where gold is found over a wide area of about 105,000 sq km (40,000 sq miles). Ashanti has been the most productive of all the lode mines and has been one of the world&apos;s notable gold producers for over 50 years. The mine is located at Obuasi, 113 km (70 miles) north and east of Tarkwa, which is 80 km (50 miles) inland from the coast. The Ashanti lode is worked on 300 m (1,000 ft) of strike length over a width of 12 m (40 ft), and by 1934 it had attained a depth of 700 m (2, 300 ft). The lode is in pre-Cambrian granite intruding a system- of shists, phyllites, etc., containing fragments of the wall rock with quartz, carbonates, sericite and small amounts of pyrite, arsenopyrite, sphalerite, galena, and gold. The shattered quartz fractures carry sulfides and gold, most of which are invisible. (William Harvey Emmons, "Gold Deposits of the World," McGraw -Hill, 1937.) Because the mill treats an ore composed of refractory sulfides - chiefly arsenopyrite and fine free gold - the flowsheet reflects the complex ore characteristics. Plane tables are used in the grinding, circuit for free gold recovery. After roasting the sulfide flotation concentrates, additional free gold is recovered from the calcines with a rotary belt concentrator and the two concentrates are combined for feed to the amalgamation pans, with the resulting gold amalgam being retorted. Following four-stage crushing to minus 9. 5 mm (318 in.) with two stages of grinding, the cyclone overflow is floated for sulfide recovery. The flotation concentrate is roasted with the calcine reground and roughly cyanided to scalp out the gold readily dissolved in one of two cyanidation circuits. The cyanide residue joins the thickened flotation tailing for cyanidation in a complete CCD circuit using filters. The gold precipitates are calcined before melting in pot-type furnaces. The tonnage to the mill of 3,175 mtpd (3,500 s tpd) with a content of over 14.7 g per mt (0.43 oz per st) places the Ashanti production as one of the top producers in the world; and with its past long life, the total production rates it as one of the world&apos;s great mines.

Jan 1, 1981

By W. R. Clough, M. E. Shank

IT has been noted in a study of the flow and fracture of nodular cast iron under biaxial stress conditions (complete results of which will be published later) that when this metal is subjected to stress it may undergo a striking density change. Such behavior was first determined by strain gage measurements made on tensile test specimens, and has since been substantiated by other types of measurement. The chemical analyses and mechanical properties of several nodular irons to be discussed here are given in Tables I and 11. Tensile data for iron A was obtained from a hollow cylindrical combined stress specimen of the same dimension as those used by L. F. Coffin, Jr.1 in his investigation of gray iron properties. Standard 0.505 in. solid tensile-test bars were used for irons B and C. On each specimen type, A-8 wire resistance strain gages were used—two diametrically opposing gages in the axial direction, two in the tangential or hoop direction. By subtracting elastic strains from the measured strains, the plastic strains could be calculated. By assuming that radial and tangential strains are numerically equal, a measure of permanent volume change can be obtained by summing the plastic strains. This appears to be a good assumption, since the metal either fractured, iron A, or readings were discontinued, irons B and C, long before necking took place. This calculated variation of volume increase with stress is given for irons A and B in Fig. 1. Data for iron C is almost identical with that for iron B. The volume change indicated by Fig. 1 has been substantiated by a more direct type of density measurement. A method developed by S. G. Fletcher and&apos; Morris Cohen,&apos; and completely described in the discussion of their article, has been used. The accuracy of specific volume measurement has been estimated as 0.00002 cu cm per gram. Essentially the method consists of weighing a sample in air and then immersed in water. Measurements were made before and after straining the material. The results shown in Table I11 were obtained by means of half-size (0.252 in. diameter, 1 in. gage length, 3/8-16 threads) tensile specimens. Initial measurements were made on the whole specimen before stressing. After stress-

Jan 1, 1955