Search Documents

By B. J. Kochanowsky

The primary use of a portable crusher, i.e., a crusher mounted on crawlers or tires, in the rock and mining industries is to reduce costs by permitting the substitution of conveyor belt haulage for truck or track haulage. The usual sequence of operations in surface mining is drilling, blasting, loading, haulage, and crushing. Haulage is normally accomplished by truck or track-mounted cars, the latter method being used for the longer distances. However, by using a portable crusher in the pit, the sequence of operations would be changed so that the crushing stage would occur before haulage (Fig. 1). Such a sequence would permit the use of conveyors to replace the more expensive truck or track haulage methods. Since most quarry and open pit operations normally require a crushing stage, the only additional costs incurred will be due to the investment required to purchase or construct a mobile arrangement for a crusher. But this factor has to be weighed against the advantages to be gained by conveyor haulage. As shown in Fig. 2, transportation of material by belt conveyor over short distances is less ex- pensive than by truck. The inclination of the belt has no effect on belt speed; consequently, the hourly tonnage moved remains the same. Conversely, the output rate of trucks as expressed in tons or ton- miles per shift decreases proportionally to the haulage speed, which is considerably slowed by the steepness of the road (Fig. 3a). Although maximum possible grades and maximum economic grades of haulage are greater for a belt than for a truck (over the same total lift), the longer haulage distances favor the use of trucks.

Jan 12, 1960

By G. C. Gambs

The electric utility industry is the largest customer of the coal industry and consumes nearly 50% of the present coal production in the United States. The byproduct of the burning of coal in utilities is ash in several forms including fly ash, bottom ash and bottom slag. At present, very little of the coal ash produced is being used and must be disposed of as waste. The coal industry should look upon this waste material as a valuable by-product which, if it can be sold for $2 to $4 per ton, will have the net effect of reducing the cost of coal to the utility by 1¢ to 2¢ per million Btu. There are many ways to use coal ash and thus benefit both the coal industry and the electric utility industry by reducing the cost of coal as burned. The solutions to the problems are obvious and all we have to do is apply them. The electric utility industry is the largest customer of the United States coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50¢ to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag. It is well known that fly ash, when used to replace a portion of the cement in a concrete mix, will produce highest quality concrete. The Corps of Engineers and the Bureau of Reclamation have constructed dams and other concrete structures for years with fly ash as a partial replacement for cement. However, many construction firms do not use it. This can become an opportunity for the coal industry to reduce the cost of coal delivered to utilities. Any fly ash, or other ash or slag, which is sold by the utilities, reduces the cost of coal burned by the utility. As much as 1¢ to 2¢ per million Btu could be taken from the fuel cost for each ton of ash sold which otherwise must be disposed of at a cost.

Jan 1, 1967

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By A. N. Chirico

This paper reviews the three major distillation processes: multiple effect (LTV) evaporation, multi-stage flash distillation and vapor-compression forced circulation evaporation. Scale preventative measures are discussed for all saline water applications. Operational data is presented on the Freeport, Texas, demonstration plant, which is the first government facility to produce one million gallons per day of fresh water for a municipality. There has been much publicity concerning the water crisis that confronts many peoples today. There is little doubt that the arid regions - which include the Middle East, parts of Africa and the Caribbean — have suffered to no slight extent for the lack of this most precious commodity. But what about our own country? Government experts have extrapolated demands and flatly predict that by 1980 we will be faced with a shortage of 80 billion gal per day. The validity of this prediction has been disputed by others; however, it appears certain that there will always be a natural abundance in some areas, a shortage of supply in other areas. Distributing our total natural water resource equitably would be impossible. Transmission of water by means of aqueducts can be an expensive undertaking. The controversial Feather River Project in Calif. is an example. The estimated cost for this venture is a staggering three billion dollars. As our population continues to increase and our standard of living rises, agricultural and industrial requirements will be proportionate. What can be done to avoid a crisis? We can conserve and use our water for industrial and irrigation purposes more judiciously: we can attempt to eliminate pollution of our natural resources from sewage and industrial wastes; we can develop, while there is time, saline water conversion processes for the massive production of low cost fresh water. The scope of this paper will be limited to only the distillation type processes that are commercially feasible. The first step in making potable water is to find a source of raw material. An inexhaustible supply is provided by oceans in coastal regions, but the supply of water is more critical in the inland communities of our country. The source of raw material in these. regions is brackish well water and this must be utilized. There is a significant process difference when handling brackish water compared to seawater and this brings out an important fact: No single conversion method can be universally applied to solve all the water problems. Composition of the raw water and degree of distillate purity are factors which must be considered before a particular process is selected. Local conditions at the plant site, fuel costs, labor costs, disposal facilities, etc. are other equally important factors which must be evaluated. WATER CONVERSION PROCESSES Conversion processes commercially feasible today are: 1) multiple effect evaporation, 2) multiple flash distillation, 3) vapor compression distillation and 4) electrodialysis. The first three are distillation processes which take potable water out of the raw water, while the fourth is a membrane process which takes out the salt. In addition to the above there are a good number of other promising methods for production of potable water, many of them in the basic research stage. Freezing is another promising process with commercial potential. This process hinges upon the formation of ice crystals which are free of salt occulsions. Separation and washing of the crystals are problems that must be solved before this process can be considered commercially feasible. Freezing processes have several advantages mostly attributable to the low temperature of operation. This low temperature reduces the scaling and corrosion problems encountered in higher temperature operations. Several different freezing processes are being considered and will be tested in the pilot plant at Wrightsville Beach. One process is a flash freeze process, a second uses a secondary refrigerant such as butane for freezing, and a third process employs a secondary refrigerant particularly controlled to produce large ice crystals. Of the above processes, only the distillation processes are reliable when water of high purity is re-

Jan 1, 1963

These pages may be used as order sheets. Mark the number desired opposite title of pamphlet wanted, add your name and address, tear out the sheets and mail them to us. Single orders 25 c. Pamphlets 10 c. each in lots of three or more. Pamphlets 5 c. each in lots of fifty or more. These prices prevail for orders for pamphlets of the same or different titles, when cash accompanies order. The pamphlets listed on the following sheets are advance copies printed to facilitate discussion at the meetings of the Institute. They are offered for sale at the reduced prices given above as long, as the supply lasts. This list is published in the Bulletin in order that members may have the first opportunity to secure pamphlets, which sometimes are in such great demand that the supply is exhausted before the wants of members can be supplied. The following list includes only a fraction of the pamphlets-that have been published by the Institute. Any other paper published by. the Institute may be obtained for the price of $1, except those published in Volume XXXI, which are rare. The, Institute is still selling back volumes of Transactions at reduced prices, but some of these volumes are becoming rare. and members who desire to complete their sets of these very important books on mining and metallurgy are advised to send in their orders as soon as convenient. The attention of members is also called to the bibliographical index of the science of ore deposits contained in the Emmons Volume which is selling at $3 in paper and $4 in half morocco. The Posepny Volume is already exhausted and members who do not get in their orders for the Emmons Volume at the present reduced price may soon find themselves unable to obtain it on such favorable terms.

Jan 7, 1917

By Jose A. Ruiz

INTRODUCTION For heterogeneous non-catalytic solid-gas reactions carried out in fluidized bed reactors, nominal bed temperature is an average value between gas and solid. For highly exothermic reactions, actual particle temperature can be up to hundred degrees above termocouple temperature, since heat dissipate at slower rate than heat generation during some steps of transformation. These micro instabilities at particle level can displace thermodynamic equilibrium from the desired phase to others. This effect is important when relatively narrow range of phase stability exists, like in sulphation roasting of sulphides, where bed discharge contains, in addition to the desired sulphate others metastable phases such as basic sulphate and ferrite. For example, for copper-iron sulphide concentration roasted below 680°C, no cupric ferrite is formed, as shown by Jakob et al., therefore the separate Kellogg's stability phase diagrams Cu-S-O represent the roasting (Fig.l). At temperature above this one, like 760°C for example, phase stability changes from CuSO4 to the basic sulphate Cu0•CuSO4. Solid state reaction between Cu0•CuSO4 and Fe203 also occurs to form cupric ferrite, Cu0•Fe2O3, therefore the Cu-Fe-S-O Kellogg's phase diagram of Fig. 1 (continuous line) represents this condition of roasting. Although both Cu0•CuSO4 and Cu0•Fe2O3 are metastable phases under normal operating conditions of sulphation roasting(1-10% SO2, 1-10% 02 and 680°C, points A and B,Fig. 1) sulphation of these species and particularly ferrite are slow and limited due to diffusional control. This explain why reactors discharge contains several phases: CuSO4, Cu0•CuSO4, CuO•Fe203 plus small amounts of CuS and FeS due to the baclonixed conditions of fluidized bed reactors. The presence of cuprous ferrite due to reducing conditions inside individual particles also occurs, but in very limited extent at the reaction interface, as it is demonstrated by the low soluble iron levels of calcines. On the other hand, the presence of cupric ferrites can be explained only due to the higher temperature achieved by particles, since below 680°C cupric ferrite formation does not take place. [ ] This phenomena also occurs for others non-ferrous metal sulphides concentrates roasted under sulphation conditions, such as 7n, Co and Ni. Therefore the prediction of discharge composition of fluidized beds is not possible based only on kinetics and mechanistics models alone or purely thermodynamical considerations, since all factors should be integrated to describe the overall phenomena. SINGLE PARTICLE TRANSFORMATION Assuming a first order reaction with respect to the gas and zero for solid, such as

Jan 1, 1984

By James H. Boettcher

INTRODUCTION A complex interaction of worldwide economic and political forces is increasingly requiring 3 primary participants for the successful development of large natural resource projects in developing countries. They are the host government of the developing country (the "host government"), one or a consortium of international natural resource companies, (the "Resource Company") and one, or more likely, a syndicate of international lenders. The host government typically controls the rights to its country's natural resources and establishes the economic ground rules for their development. However, because of worldwide inflation and the depletion of easily accessible, high-grade resources, the nominal and real capital development and operating costs of projects have been spiraling. Moreover, the depletion of high-grade and mineralogically uncomplicated resources also raises the technical and operating risks associated with resource recovery. Thus, despite increasing political self-consciousness and economic nationalism in developing countries, international resource companies are still often necessary project sponsors since they can provide, among other things, the required technical and management expertise and equity capital. The presence of these factors, and often the addition of worldwide market access in a project, is often critical in determining whether or not the project will be considered creditworthy by international commercial lenders. The international commercial lender is often the critical third party in project development, due in a large part to the ever escalating-costs of project developments relative to the financial resources of many companies and even a growing number of countries. In addition, lenders have other reasons for taking more than a passive interest in all aspects of a project's development. These reasons include the following: 1. Projects are often financially structured such that the primary security for a loan, once completion and performance standards are met, is the cashflow of the project rather than recourse to its sponsors. 2. Lenders, in addition to the "project risk" just described, are frequently asked to assume various elements of "political" risk which nay put them in a sensitive economic position between the host government and international resource firms (This is discussed later). 3. International banks today have large loan portfolios of developing country debt with final maturities ranging from one to fifteen years. The various current projects undertaken are the building blocks of most developing country economies that will hopefully contribute to the long run economic development of a country as well as generate the foreign exchange necessary to repay foreign loans in the future. In this regard it is useful for lenders to realize whether a given project "makes sense" in terms of a country's natural resource endowments and competitive advantages over other countries. The type of framework discussed in this article would help lenders to better make such assessments. In order to facilitate the continued international flow of capital and technology to developing countries and of readily available supplies of raw materials from them, it is important for each of these three parties to increase its awareness of the goals and objectives of the other parties as well as the bargaining process that results in the legal, financial, credit and fiscal structures by which a joint venture project ultimately proceeds. Each of the parties faces increasingly complicated accept/reject decisions when they are faced with difficult choices among. a wide range of alternative structural combinations each of which has different implications for risk and reward to them. Therefore, by increasing the mutual, 3-way awareness of the decision processes of the other parties, it should be possible to: • provide better information and results in the formation of more rational expectations by all parties going into negotiations, • facilitate the project formulation process by allowing parties to focus more clearly on the areas of common interest and conflict, • result more frequently in final structures and agreements that better reflect the economic and political realities associated with a project and thus • result in more creative, innovative agreements that should reduce the need for changes to them and thus promote the kind of long run political stability conducive to attracting capital and further investment.

Jan 1, 1982

By F. W. Jr. Sperr

THE byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.) 69 per cent. of coal Domestic coke (1/2 to 3/4 in.) 2 per cent. of coal Breeze (under 1/2 in.) 4 per cent. of coal Surplus gas, cubic feet per net ton 6600 Gas for heating ovens, cubic feet per net ton 4400 Tar, gallons per net ton 9 Ammonium sulfate, pounds per net ton 25 Benzols, gallons per net ton 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke,"' "beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writer1 stated that in brass-foundry practice, Connellsville coke is considered much superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in mak-

Jan 10, 1920

By J. V. N. Dorr

DEADWOOD and the Black Hills were familiar names to me from childhood, for. I had an uncle who was among the earliest eastern investors there and I used to hear of the Uncle Sam mine and its rich ore back in the eighties. The spring of my junior year at college, in 1893, brought me an offer of summer work at the Deadwood & Delaware smelter, in Deadwood, and full of the thrill of the long journey from New Jersey, I went out as chemist and stayed four months. Within a week or two of my arrival, I went through the tragic experience of seeing an associate drink cyanide by mistake and die within a few moments. I shall never forget the horror of feeling that my lack of knowledge of an antidote might be responsible for his death, but I found later that the solution he drank was so strong that nothing could have been done. A year after graduation, when I had settled down to chemical research work in New York, an offer came to go back to the smelter in Deadwood, and within a few days I was again tramping down "the Gulch" with my lunch bucket and putting in the standard assay office shift of that day, from 7 a.m. to 6 p.m., with a half-day off on Sundays. During my absence East, the D. & D. smelter had been changed from a pyritic smelter, using native pyrite, and Homestake concentrate to matte the siliceous gold ores, into a copper-matting smelter using copper ores brought from Butte, over the newly-completed Burlington rail-road. The work was interesting, and the laboratory offered many opportunities for making improvements. I remember also undertaking experiments at home on a new method of gold precipitation for the chlorination process and leasing a mine in Strawberry Gulch that promised great things, but soon petered out.

Jan 8, 1927

By D. Turnbull, J. H. Hollomon, J. C. Fisher

UNDERSTANDING of the diffusion problem has recently been furthered by the analysis of Birchenall and Mehl.1 They pursued the problem of the variation of the diffusion coefficient with composition for non-ideal solid solutions. Their analysis follows the tradition of Wagner,2 Jost,3 Dehlinger,4 and Darken,' who assumed the net flux of dif¬fusing material to be proportional to the gradient of a quantity related to free energy. The basic assumption in Birchenall and Mehl's formulation of the problem is that the net flux of diffusing material is proportional to a thermodynamic activity gradient. To estimate the applicability of the derived relations, they corrected the diffusion coefficients of carbon in austenite by utilizing Smith's' activity data for carbon, and the diffusion coefficients for zinc in copper with activity data computed from the vapor pressure measurements of Hargreaves.7 The corrected coefficients for carbon were virtually independent of carbon concentration. For the diffusion of zinc in copper a moderate variation of diffusion coefficient with concentration remained after the correction. The problem of diffusion can be formulated in another way than that used by Birchenall and Mehl. The method is that of chemical rate theory and has been used by Eyring and his coworkers8,9 as well as by Eyring and Zwolinski10 in a discussion to Birchenall and Mehl's paper. As yet the method has not been applied to substitutional solid solutions. On the basis of their assumptions, Eyring and Zwolinski derived a relation between the diffusion coefficient and activity that is identical with that of Dehlinger and Darken but which does not correct for the variation of the diffusion coefficient with concentration as well as does the relation derived by Birchenall and Mehl. It was thought that the theory of diffusion would be more complete if the inconsistency between the two analyses could be rationalized and if diffusion in substitutional alloys were analyzed on the basis of the concepts of the chemical rate theory. CHEMICAL RATE THEORY According to the theory of absolute reaction rates8 the reaction [A,+A2+ ... +.A;->X,+X2 +...+X; EqI] is viewed as taking place in two steps. First the reactants A1, A2, . . . A[i] combine to form an activated complex M with which they are in equilibrium; [A, + A2 + .. . + Ai = M. Eq 2] Second the activated complex decomposes to give the products X1, X2. . .. X[j]; [M->X1+X2+ ... +.X;. Eq3] It has been shown8 that the number of activated complexes decomposing per unit volume per unit time is given by the expression† [kT]

Jan 1, 1948

By Donald Cummings

MEASURES appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-19 has accumu-lated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors-the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Con-trol of the danger arising out of prolonged contact with pernicious air-borne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects-one, medical; the other within the province of the engineer.

Jan 1, 1938

By R. A. Ronzio, P. B. Queneau, C. A. Born

The molybdenite flotation operation of Climax Molybdenum Co., Division of AMAX Inc., near Leadville, Colo., generates a rougher tailing containing 0.03% W03 and 0.005% SnO2. This tailing is subjected to a series of mineral beneficiation steps for production of wolframite and cassiterite concentrates. However, these byproducts are contaminated by small quantities of UsOa. This paper describes application of sulfuric acid-sodium chlorate leaching for substantial elimination of the radioactive impurities, particularly the mineral brannerite. The leached residue is amenable to magnetic separation of wolframite from cassiterite.

Jan 1, 1976

By Derek C. Shelton

This chapter covers the preparation of specifications for a dry crushing and wet grinding comminution circuit.

Jan 1, 1982

By Sam Tour

Some years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.' The life of dies was considered in relation to. the casting temperature, the material used for the die and the heat to be absorbed by the die per unit volume of casting made. The mechanism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines. Importance of Heat Checking Heat checks in steel are the source of trouble in many industries besides that of die casting. Every shop where metals are subjected to hot working is searching for improvement and hoping for a cure. The development of a material of sufficient strength to be used as a die and yet devoid of the property of heat checking would be a godsend to many shops and many industries. The need for thorough study and research on the subject is evidenced by the wide variety of hot-working die steels on the market. It is peculiar, but true, that in practically every case the maker of the steel can give concrete evidence to prove his contention that his type of hot-working die steel is as good as or better than any other. A number of steel companies have several hot-working die steels from which choice can be made to fit a particular set of requirements. Possibly to expect one material to be universally the best hot-working die steel is unreasonable. In some hot-working operations, as in drop forging, the die must have great toughness to withstand the stresses developed; in other operations, as in hot piercing or punching, resistance to erosion at high temperatures, possibly defined as strength and hardness at elevated temperatures, is required. In still others, as in die casting, only sufficient hardness to resist scoring between moving surfaces is required, whereas the resistance to sudden changes in temperature must be at a maximum.

Jan 1, 1935

By Sam Tour

Some years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.' The life of dies was considered in relation to. the casting temperature, the material used for the die and the heat to be absorbed by the die per unit volume of casting made. The mechanism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines. Importance of Heat Checking Heat checks in steel are the source of trouble in many industries besides that of die casting. Every shop where metals are subjected to hot working is searching for improvement and hoping for a cure. The development of a material of sufficient strength to be used as a die and yet devoid of the property of heat checking would be a godsend to many shops and many industries. The need for thorough study and research on the subject is evidenced by the wide variety of hot-working die steels on the market. It is peculiar, but true, that in practically every case the maker of the steel can give concrete evidence to prove his contention that his type of hot-working die steel is as good as or better than any other. A number of steel companies have several hot-working die steels from which choice can be made to fit a particular set of requirements. Possibly to expect one material to be universally the best hot-working die steel is unreasonable. In some hot-working operations, as in drop forging, the die must have great toughness to withstand the stresses developed; in other operations, as in hot piercing or punching, resistance to erosion at high temperatures, possibly defined as strength and hardness at elevated temperatures, is required. In still others, as in die casting, only sufficient hardness to resist scoring between moving surfaces is required, whereas the resistance to sudden changes in temperature must be at a maximum.

Jan 1, 1935

By Harold Cook

THE purpose of this paper is to state briefly the inspection requirements of the Bureau of Ordnance, the specifications governing the inspection, and the physical and chemical properties of the steel used in the construction of ordnance for our Navy. It would be of interest to evoke discussion on points in these specifications which do not tend to insure the production of the very best material for the purpose intended. In other words, what requirements of our specifications are useless and also in what manner are our specifications deficient? It might be well at the, start to answer the first criticism of this paper which will probably be made, and that is that the title does not agree with the subject matter. Considering metallographic work as covering only the macroscopic and microscopic examination of metals, this paper will have gone beyond the subject; but it is believed that a broader definition of metallography is that it is the study of the relation of the internal structure of metals and alloys to their composition and to their physical and- other properties. The internal structure of steel is dependent on its physical and its chemical properties. These physical properties are dependent on the chemical composition and the mechanical and thermal treatment of the steel. So it seems that this subtitle would not be entirely necessary and that the title "Metallography of Steel for Ordnance Purposes" would cover a study, not only of what we can learn of macroscopic and microscopic examination, but broadly of the whole subject of the specifications, the fulfillment of the requirements of which produce the structural conditions revealed by macroscopic and microscopic examination. .

Jan 2, 1916

By K. Thirumalai

Rock response to heating depends on properties of rock material and varies widely between different rock types. By dissipating energy, surface melting limits rapid heating and fragmentation of rocks achieved by surface heating methods. This study advances a concept of rock fragmentation by rapid internal heating of a localized inner volume of rock. The working of the method to achieve fragmentation of rocks (Charcoal granite and Dresser basalt) having poor response to surface heating is analyzed. Experimental data on elevated temperature rock properties required for the study are presented. Based on the properties of test rocks, a high frequency (50 MHz) dielectric heating method of generating localized internal heating was selected for experimental study. The test rocks were fragmented without melting under localized heating below 600ºC. The heated volume required for fragmentation was observed to be less than 2 percent of the test block volume. A practical application of the method for in situ fragmentation of rocks is suggested.

Jan 1, 1971

By C. Grua, M. Gottlieb, E. M. Wewerka

The Purpose of this paper is to present an overview of research underway at the Los Alamos Scientific Laboratory to investigate some of the more attractive options for controlling trace element contamination of coal refuse drainages. * The control methods under consideration include chemical and physical methods to immobilize or remove undesirable contaminants prior to refuse disposal, the treatment of refuse disposal sites with attenuating agents to prevent the discharge of contaminated water, and the direct treatment of refuse drainage as it emerges from the refuse disposal site. The results from these laboratory studies suggest that many of these techniques are technically feasible for controlling trace element contamination of refuse dump drainage.

Jan 1, 1982

By John M. Hartman

(Read at the Wilkes-Barre Meeting, May, 1877.) Two systems are used for heating air in blast-furnace operations I. The double surface system, in which a cast-iron pipe is heated on the outer surface, and, at the same time, heats the blast from its inner surface. This is simple in operation and gives a continuous effect, but is limited by 1100° F. as a maximum temperature of the blast. II. The single surface system, by which large surfaces of fire-brick are heated, and air passed over the heated surface, absorbing the heat and carrying it on to the furnace. This system is more complex than the double surface, as it involves the reversing of the air and gas every hour and a half. The single surface system has two advantages: 1. The blast can be heated to a temperature of 1800° F. 2. The stoves are indestructible. From recent experience it has been found that 1300° F. to 1400° F. is the best average temperature for economy of coal for safe work¬ing. This is equivalent to a saving of 12 to 2 cwt. of coal per ton, of iron over the extreme limit of cast-iron stoves. Independently of this, it is a strong point in favor of this system that the blast can be raised to a temperature of 1800° F. within an hour when the hearth is getting cold. All furnacemen know the value of a hot hearth for quality and quantity of iron. Cooling of a hearth occurs from leaky tuyeres, scaffolds, or heavy burden. When there is not sufficient coal at the tuyeres to seize on the oxy¬gen of the entering air and convert it at once to carbonic oxide, there will not be enough heat to liquefy the cinder. Black cinder and poor iron are the results. The remedy is additional heat from the blast. If the stoves will give 1800° in place of 1100°, it is obvious that the furnaces will get around sooner, and without waiting for a change of burden at the tunnel head to bring extra coal to the hearth. The heat absorption caused by a leaky tuyere will chill the hearth and drive the zone of fusion higher up in the furnace. This loss must be supplied, and the calories lost to the hearth must be regained before good iron can be made. Take another case : A furnace carefully burdened on No. 1 iron, during a spell of damp weather, goes on to No. 2 or No. 3. Heat is lost to the furnace through absorption by the moisture, and less burden must be carried in order to get back on No. 1. When the

Jan 1, 1878

By H. W. Smith, A. K. Bjerring

A nonlinear dynamic model for a flotation cell is developed, using a number of simplifying assumptions, the most important of which is that of essentially complete liberation in the feed material. Using this model, a complete dynamic model for a flotation circuit is developed and calibrated against steady- state process data. The dynamic response of the circuit to disturbances in input feed rate and composition is simulated, as is the response of a linearized and simplified model on which control design might be more easily based. Preliminary results indicate the practicability of the modeling technique. However, difficulties in matching steady-state operating conditions in one process stream, and the apparent importance of recycle streams as indicators of process operation, indicate that inclusion of at least one species of middling particle in the model should be considered.

Jan 1, 1969