Search Documents

By C. W. A. Newey

I would like to make the following points in connection with the studies of the deformation of NiAl reported in the recent paper by Wasilewski, Butler, and Hanlon. 1) Much of their paper is concerned with demonstrating that slip occurs on either {110)(001) or {100)(001) systems. In their discussion they state "the existence of (001) as the basic slip direction can thus be considered established." This fact was established by the earlier studies of Ball and Smallman.32 Ball and Smallman also concluded that the slip plane was of the type (110) and they showed that cross slip or pencil glide on orthogonal (110) planes could produce macroscopic slip on planes of the (001) zones, e.g., (100). Wasilewski et al. refer to this paper by Ball and Smallman but not in connection with the slip system determinations. 2) Wasilewski et a!. eliminate the possibility of (111) slip in NiAl on dubious grounds. Their statement that ('the very high yield strengths of the (100) oriented crystals", in which (001) slip is constrained, "immediately ruled out the possibility of {110)(111) slip" cannot be accepted unequivocably; it would be reasonable if the crystals were completely brittle but they are not, as Wasilewski et al. and others33734 have shown. Their elimination of the possibility of (111) slip in a crystal compressed along [227] is misleading since there is no obvious reason why (111) slip should occur in a crystal of this orientation. In fact, from an analysis of the macroscopic surface markings on deformed (100) stoichiometric crystals, Pascoe and Newey34 have deduced that slip occurs on systems of the type {211)(111) and {321)(111). 3) Polycrystalline NiAl is known to undergo general deformati~n.Having emphasized that general deformation is impossible if only (100) slip occurs, it is a pity that Wasilewski et al. do not attempt to account for the disagreement between theory and their experimental results. Of course, (111) slip can provide the additional independent systems required for general deformation.

Jan 1, 1969

By William Catron, Cyril U. Colledge

BECAUSE the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It was clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stopes below with disastrous results to men and mine. The method of mining developed during the years 1928, 1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. GEOLOGICAL STRUCTURE The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1938

By Richard D. Snouffer

Prime topics of conversation these days are the new concepts of rail haulage for bulk items such as iron ore, potash and coal. We have heard such ideas as the "integral train" and the "unit train" discussed frequently during the past two years at various AIME meetings, and progress reports have kept up a steady appearance in the technical press and in local newspapers. While no railroad has a complete "unit train" in service at this moment, one has 50 fast-discharge cars under construction and the Pennsylvania Railroad has experimented with radio-controlled motive power distributed at intervals throughout the train. To a great extent, however, the promise for greater efficiency and lower costs held out to industry by these new haulage methods is dependent not on greater speed or larger cars or more dedicated equipment alone but, rather, on the utilization of modern practices in the loading and unloading of rail cars. It is the purpose here to examine these two key steps and the up-to-date procedures and equipment they entail.

Jan 7, 1963

By C. E. Arnold

IN attacking the problems of mining and treating large disseminated copper orebodies such as those occurring in the Miami or the Ray district of Arizona, one of the vital questions to be decided is, "What is the value of the orebody per ton in place?", The importance of this question lies in the fact that its answer helps to reach a decision concerning the method of mining to be employed. Let it be assumed for the moment that milling and smelting practice, especially the latter, is more or less standardized; and has a cost incapable of much variation, while the cost of mining has a considerable range owing to the large number of mining methods by which a mine may be exploited. For instance, a method may be adopted whereby all the available ore can be extracted perfectly clean (i.e., unmixed with barren material) at a relatively high cost; or a method may be used involving the necessary dilution of a portion of the ore with waste, in order to recover that portion, thus giving a relatively poorer extraction but nevertheless a lower working cost than the former method. Naturally, between these two extremes there lie intermediate methods. In order to arrive at a solution of a mining method problem that is of any value, it is necessary that accurate and complete estimates of mining, milling, and smelting performances and costs shall be established. By way of illustration is given a, case of mining, by the system of undercutting and caving, a large orebody with an average content of 1.50 per cent. copper supposedly all in sulphide form, to which case has been applied those results in mining operations which one may fairly assume are to be expected when viewed in the light of G. R. Lehman's ore-drawing experiments, which form the subject of a paper to be presented at this meeting. It is assumed that the total. costs will be as shown in the following table:

Jan 9, 1916

By John C. F. Randolph

(Read at the Amenia Meeting, October, 1877.) Tits establishment being now in full working order, it has seemed of considerable professional interest to collect together, in a concise form, the various points as to its plan, method of dressing, and equipment. The data contained in this paper have been largely drawn from the able paper of E. Kutscher, constructing engineer. of the works, contained in the Zeitschrift fur Berg-Hütten-und Salinenuesen im Preussischen Staate, 1873, supplemented by some personal memoranda made while the works were under construction and by memoranda on the works appearing in various German technical papers from their completion up to date. This is probably the largest dressing works in the world devoted to the beneficiation of argentiferous lead ores, and it is doubtful if any establishment for the concentration of mineral of any description can compare with it in size. As showing the final practice adopted in an old and very conservative mining region, in which the concentration of ores has been a matter of constant practice and experiment for a very long period, these works are of peculiar interest. The fact that the Clausthal ores strongly resemble a very large and abundant class of ores found in the United States has always attracted the attention of American mining engineers and mine owners to the methods employed in dressing and smelting them. The study of their methods of concentration of ores has, however, always been full of difficulty,

Jan 1, 1878

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960

By Charles White Merrill

A forecast of mineral demand during the remaining years of the 20th century can serve as an excellent starting point for student mining and mineral engineers in planning their professional careers. This approach of appraising demand before seeking supply is not new. of course, but, it is quite the opposite of the traditional attack on mineral resources in which adventurous prospectors, followed by practical miners and engineers, have in the past sought out and developed mineral supply with a faith that markets existed for the products they were preparing to offer. Such faith, even to this day remains fully justified if the product is gold, which still enjoys an unlimited market at $35 a fine ounce, but other mineral products must compete in markets of varying stability and capacity for adsorbing new supply. The world is in a period of rapid expansion. Most basic is the worldwide increase in the number of people which has reached proportions popularly termed "the population explosion." Conservative demographers, noting an increase from 1 ?h billion people at the beginning of the 20th century to 3 billion today, are predicting 5 billion by the year 2000; some predictions are much higher.

Jan 2, 1964

Visitors frequently put the question to Kalgoorlie gold miners; "Why don't you concentrate your mining operations?" A mine may be drawing ore from over a hundred different working places which are spread out over several thousand feet of strike and on many different levels. The answer to this question is that "finished" can rarely be written for a section of the mine. The intricate web of mineralization in faults, shears and fractures is an endless puzzle, each solution opens up new avenues to be explored. After the last ore is taken from a stope, a program of drilling may continue for several weeks on different possibilities. Perhaps no ore is discovered and drilling is abandoned, but it is not unusual for another search to begin later in that same area on a new theory with successful results. Wherever a slightly richer mineralization is found, it is needed to "sweeten" the mill heads. Over seventy years ago gold was discovered in the dry wastes of Western Australia. Rich deposits of alluvial gold were found at first and as these were worked out they led to the discovery of the lode ores, which were leaner and harder to extract.

Jan 10, 1964

By S. N. Sharma, William Davis

Because of diminishing energy resources and rising energy costs, every industry is forced to carefully examine its pattern of energy consumption. The copper industry is no exception; current smelting practice begs for technological innovations that would improve the efficiency of its energy utilization. The thermochemical simplicity of copper metal production, as shown in Fig. 1, is deceptive. Designed from the same basic principles, there are four major commercial processes either in use or under construction; and others, such as the Mitsubishi process, are being developed.

Jan 5, 1977

By C. E. Armantrout, J. A. Rowland, D. F. Walsh

THE close-packed-hexagonal structure of mag-J- nesium is converted to a ductile and malleable body-centered-cubic lattice by the addition of lithium in excess of 10 pct. Further, the density of magnesium or magnesium-base alloys is decreased by additions of lithium. The practical possibilities of such alloys as a basis for uniquely light, malleable, and ductile structural materials were pointed out by Dean in 1944' and by Hume-Rothery in 1945.2 It was apparent to these investigators, however, that more complex compositions would be required if strengths sufficient for structural applications were to be developed in these alloys. In a search for strengthening additions, various investigators w have examined a number of the ternary and more complex alloys containing magnesium and lithium. An investigation of the fundamental characteristics of these alloys was undertaken by the Bureau of Mines. The investigation was initiated with a study of the magnesium-rich corner of the equilibrium diagram for the ternary system, Mg-Li-Al. The following data from published investigations of Mg-Li-A1 alloys were available: 1—a description of isothermal sections at 20" and 400°C through the Mg-Li-A1 constitution diagram by F. I. Shamrai;' 2—a diagram by P. D. Frost et al." showing approximate phase relationships at 700°F for a number of the Mg-Li-A1 alloys; and 3—diagrams showing the constitution at 500" and 700°F for the Mg-Li-A1 alloy system published by A. Jones et al.' Where compositions and temperatures permit comparison, these diagrams show disagreement. The 700°F isotherms of Frost and Jones differ only in the placement of the phase boundaries. But Sham-rai's 400°C (752°F) isotherm shows a variation in phases as well as in phase boundaries. Although rigid comparison of these different isothermal sections might not be justifiable, it seems impossible to reconcile Shamrai's construction with the isotherms of Frost or Jones. The isothermal sections presented in this paper were prepared to determine compositions which might be suitable for age hardening and to develop the general slope and placement of the various phase boundaries in the magnesium-rich corner of the diagram. Sections at 375", 200°, and 100°C were selected for investigation. In constructing these sections, the solubility of aluminum in magnesium, as reported by W. L. Fink and L. A. Willey Vn 1948, was used at the binary Mg-A1 boundary and the solubility of lithium in magnesium was obtained from the equilibrium diagram for that system as reported by G. F. Sager and B. J. Nelson" in the same year. The solubility of magnesium in lithium was determined experimentally and conforms in general to data reported by P. Saldau and F. Shamrai." Parameters for AlLi and MgI7A1, were taken from American Society for Testing Materials X-ray diffraction data cards. Experimental Procedures Although the isothermal sections presented in this paper are not unusually complex, the experimental techniques involved in their construction are made extremely difficult by the relatively high vapor pressure of lithium and the great chemical activity of both magnesium and lithium. Because of these characteristics, which make precise control of the composition of equilibrium-treated filings practically impossible, the disappearing phase method was used in preference to the parametric method in conjunction with metallographic studies. The alloys used in this investigation were melted and cast in an atmosphere of helium using a tilting-type furnace which enclosed a steel crucible and mold in a single unit. Each portion of the charge (500 to 600 g) was cleaned carefully just before placing it in the crucible; and the charge, crucible, and entire melting apparatus were evacuated and then washed with grade A helium while preheating to approximately 100°C. The alloys were melted and chill cast in an atmosphere of helium. Alloys prepared in this way were relatively free from inclusions and a fluxing treatment was considered unnecessary. The cylindrical ingots obtained were scalped and then reduced 96 pct in area by direct extrusion, yielding % in. diam rod. Sections of the rod, approximately 3 in. long, were given equilibrium heat treatments and then sampled for metallographic examination, X-ray diffraction study, and chemical analysis. The surface of each equilibrium-treated rod was machined to a depth sufficient to insure removal of contaminated material before samples for chemical analysis or X-ray diffraction study were obtained, and all decisions on microstructure were based on the examination of the central portion of the metallographic specimen. All specimens homogenized at 375°C were analyzed after this equilibrium heat treatment. When the composition of an alloy placed it in a critical area of the 200" or 100°C isothermal section, a check chemical analysis was made on a sample taken from the alloy specimen as-heat-treated at the particular temperature. Standard chemical procedures of gravimetric analysis were used in the determination of magnesium and aluminum; lithium, potassium, and sodium were determined by flame photometer methods

Jan 1, 1956

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

The tensile properties, creep resistance. and thermal stability of highly alloyed Ti-Al-Zr alloys were examined. On the basis of these studies, the Ti-7Al-1ZZr composition was selected for more complete evaluation. The alloy was found to be weldable and free from excessive directionality. In addition, it developed maximum properties without requiring heat treatment other than an annealing operation in the alpha field. The alloy was recommended for scale up and is presently being investigated on a production-level basis. One of the more attractive properties of titanium alloys is their ability to withstand stress at moderately high temperatures, and a considerable amount of effort has been devoted to increasing the maximum service temperature of titanium alloys. This work has suggested that the optimum alloys for high-temperature service will be single-phase a (close-packed hexagonal) alloys containing significant amounts of aluminum. However, the maximum amount of aluminum which can be alloyed with titanium is between 6 and 8 pct,l since at high-aluminum contents an embrittlement reaction occurs in the anticipated service temperature range, 800" to 1100°F. It has been shown that the embrittlement reaction involves decomposition of the high-aluminum a phase to one or more new phases.' Since this reaction does not occur at intermediate or low-aluminum contents, it was felt that intermediate Ti-A1 alloys might be strengthened by a-soluble ternary additions without inducing the embrittlement reaction. The first alloying addition considered was tin, which shows extensive solubility in a titanium and has moderate strengthening tendencies. Unfortunately, it was soon apparent that tin also promoted the embrittlement reaction, and that to obtain a stable alloy, the aluminum content had to be reduced as the tin content was increased. The second alloying addition considered was zirconium, which is similar to tin in its effects on titanium. This element did not contribute to the embrittlement reaction and, in fact, appeared to increase the maximum amount of aluminum which could be alloyed with titanium without inducing instability. This paper describes an investigation of the Ti-A1-Zr a alloy region. Alloys containing from 4 to 12 pct A1 and from 6 to 15 pct Zr were examined. The properties of these alloys are described and the bases for selecting an optimum composition is outlined. This composition, Ti-7A1-12Zr, is presently being scaled up in tonnage quantities, and is being evaluated extensively throughout the industry. In addition to presenting the basis for its selection, this paper presents a description of the properties developed in laboratory material as determined during the alloy investigation. These properties suggest that this alloy can fill an important position in applications requiring light weight, fabrica-bility, weldability, and strength to 1000oF or higher. EXPERIMENTAL PROCEDURES Titanium alloy ingots were prepared by inert electrode arc melting under an argon atmosphere. Alloying elements used were 110 Bhn titanium sponge, high-purity aluminum, and reactor-grade zirconium. Pancake-shaped ingots were prepared weighing approximately 300 g. The composition of the ingots was checked by weight measurements before and after melting. The pancake ingots were forged at 2000°F to approximately half their original thickness to give a flat plate roughly 1/2 in. thick. This plate was then rolled at 1800' to 1600°F to 0.250 in. thick. All of the alloys examined fabricated well. However, alloys containing 15 pct Zr tended to overheat due to exothermic oxidation, and scaling was excessive. As might be anticipated from its effect in decreasing the ß transus, increased zirconium appeared to improve fabricability somewhat, especially during rolling at lower temperatures. Except for a limited study of heat-treatment response, all alloys were examined in the a-annealed condition. Prior to heat treatment the a and ß tran-sus temperatures were determined by metallo-graphic examination of samples quenched after annealing at 50-deg intervals in the transformation region. These data are shown in Fig. 1. Recrystal-lization appeared to occur in about 1 hr in the range 1300º to 1500ºF. Therefore, alloys were annealed for 1 hr at 1550ºF (4 and 5 pct Al), 1600ºF (6 through 7-1/2 pct Al), or 1650°F (8 or more pct Al). This produced an equiaxed a grain structure. In most alloys, a "ghost" structure was visible after the a-annealing treatment, as shown in Fig. 2. This structure apparently resulted from the acicular

Jan 1, 1963

By W. L. Zeigler

THE year 1930 in the Ceur d? Alene district was one of curtailment in production. Many of the small properties were closed entirely and only three large. producers, the Bunker Hill & Sullivan, Hecla, and the Morning mines were left producing at capacity. No innovations in milling were evident, but progress was made in reducing costs as is always necessary in times of low metal prices. One new concentrator was constructed, a 500-ton daily capacity selective flotation plant for, the Jack Waite Mining Co. This mill uses coarse crushing, followed by hand sorting, for both a high-grade ship- ping ore and waste. The remainder of the ore leaving the sorting belt is crushed in a new type Traylor reduction crusher to %-in. size and stored in large capacity mill ore-bins. The grinding is done with ball mills, in closed circuit with a Dorr classifier to 75 per cent - 200 mesh. Minerals Separation 24-in. flotation machines are used both for a lead and a zinc concentrate, with double cleaning in each case. The concentrates are dewatered in Dorr thickeners and filtered on Oliver late-type filters.

Jan 1, 1931

By W. C. PAGE

HARVEY S. MUDD has the unusual distinction of having virtually inherited a Directorship in the -A.I.M.E., for he was appointed to the Board to fill the unexpired term of his father in 1926. Since then he has served as a Director continuously until 1936, and now he is a candidate for Vice-President. One of the first words that young Harvey tried to say was "ore," for he was born in Leadville, Colorado, in the heyday of that camp, where Seeley W. Mudd for years ran the Small Hopes mine. Stanford and Columbia gave him his mining education, and the Shattuck-Arizona, at Bisbee, his first job. Afterwards he examined many

Jan 1, 1937

By C. W. Sherman, N. J. Grant

The correlation of the high temperature chemical properties of slag-metal systems with some easily measured property of either slag or metal at room temperature has been the goal of both process metallurgists and melting operators for many years. There are several rapid methods for estimating various constituents in steel in addition to the conventional chemical methods which are quite fast, but these do not reveal the nature of the slag as a refining agent, which is of primary interest to the steelmaker. Furthermore, there are several methods for examining slag, the three principal ones being slag pancake, petrographic examination, and the previously mentioned chemical analysis. The main objection to the last two is the lime required to make a satisfactory estimate of the mineralogical or chemical components. The objection to the first is the inadequacy of the information obtained. A new technique has been developed by Philbrook, Jolly and Henry1 whereby the properties of slags are evaluated from an aqueous solution leached from a finely divided sample of slag. It is known that the pH or hydrogen ion concentration (of saturated solutions that have dissolved certain basic oxides, notably calcium oxide) will indicate a pronounced basicity. Philbrook, Jolly and Henry devised the pH measurement technique in order to supply open hearth operators with a fast, reasonably accurate method of estimating slag basicity. They offered the method as an empirical observation and made no claims as to its theoretical justification. The results were presented as an experi-metally observed relationship which applied over an important range of basic open hearth slags. They found that, in plotting the measured pH against the basicity, the best relationship existed between the pH and the log of the simple V ratio, CaO/SiO2. Extensive investigation also showed that there were several variables in the experimental technique that influenced the results and necessitated following a standard procedure to obtain reproducible pH readings. These variables were: 1. Particle size of the slag powder used. 2. Weight of sample used per given volume of water. 3. Time of shaking and standing allowed before the pH was measured. 4. Exclusion of free access of atmospheric carbon dioxide to the suspension. 5. Temperature of the extract at the time the pH was measured. In subsequent investigations of the pH method by Tenenbaum and Brown2 and by Smith, Monaghan and Hay3 the general conclusions of Philbrook's work were reaffirmed. It was the object of the present investigation to extend the technique to a point where it could be used to evaluate slags of all types. Experimental Results PARTICLE SIZK OF SLAG POWDER A large sample of commercial blast furnace slag of intermediate basicity (V-ratio 1.15) was selected for the study. The slag had been put through a jaw crusher until all of it passed through a 20 mesh screen. Five fractions of this crushed material were separated, -20 to +40, -40 to +60, -60 to +100, -100 to +200, and -200 mesh. A representative sample of 0.5 g was removed from each fraction and the pH determined using the method of Philbrook. Check pH analyses on the sample fractions varied due to the different amounts of shaking. To eliminate this variable, a mechanical shaker was employed. In order to know the exact time of contact between the slag and water, it was found necessary to filter the extract at the end of the shaking period. Using the mechanical shaker and a filtering apparatus, similar runs were made on the five fractions for contact times of 5, 10, 20, and 40 min. Random checks gave reproducible results within 0.02 pH. The data are plotted in Fig 1. It can be seen from the plot that each slag fraction is hydrolyzed to an extent that is roughly proportional to the surface area exposed to the water. The (—100 to +200) mesh material changed very little in pH after 10 min. shaking time. The curves are symmetrical and lie in proper relation to one another. The —200 mesh curve appears to be somewhat flatter than the others, but this can be attributed to the portion of very fine material that is not present in the other fractions. The closeness of the (-100 to +200) mesh curve to the —200 mesh curve and the fact that a —100 mesh sample would contain amounts of slag down to 1 or 2 microns in diam were considered sufficient reasons for selecting a —100 mesh sample as representative of the whole sample of slag for the purposes of this investigation.

Jan 1, 1950

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939