Search Documents

By H. J. Rose

SIXTY-FIVE million net tons of coal were carbonized in the by-product and beehive coke ovens1 of the United States during 1924. This tonnage represented 13.4 per cent. of the bituminous coal which was mined in that year. Table 1 shows production and disposition.2 TABLE 1.-Production and Disposition of Oven Coke in 1924 BY-PRODUCT BEEHIVE TOTAL Coal charged into ovens, tons 49,061,339 15,914,310 64,975,649 Coke produced (exclusive of screenings and breeze), tons 33,983,568 10,286;037 44,269,605 Average yield of coke, per cent 69.3 61.6 68.1 Disposition of coke: PER PER PER CENT. CENT. CENT. Blast furnace 82.5 82.8 82.6 Foundry 4.6 13.3 6.6 Domestic 8.3 1.4 6.7 Water gas manufacture and all other uses 4.6 2.5 4.1 Cokes having somewhat different combinations of chemical and physical properties are desired for the various uses listed above, and these properties depend primarily upon the types of coal used. American coals have a wide range of purity and coking quality, and the chief subject of this paper will be the selection of coals for the manufacture of blast furnace, foundry, domestic, and water-gas coke, in by-product coke ovens. It will obviously be necessary to include a discussion of those physical and chemical characteristics that are generally considered essential or desirable for each type of coke.

Jan 7, 1926

Gentlemen.-It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute. As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition. With property valued at more than three-quarters of a million dollars, and with considerable sums in various funds and endowments, it is possible to spend on each member of whatever class $22.65 each year, more than the maxi- mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all. To do this has required close management and a strict regard for our limitations. In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initiation fees to the General Reserve, and still only reduce the cash balance $2,074.54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratuitous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally. Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds. PUBLICATIONS In an analysis of the income and expenses of the Institute published in the February issue of our Journal, MINING AND METALLURGY, it was pointed out that the largest item of expenditure is, as it should -be, for publications. Printing, binding, and distributing the various technical papers sent to the members cost in 1926 more than all the money received from dues, including the portion allocated as subscription to the magazine. Within the. year, the following volumes were printed and, with the exception of the second volume of TRANSACTIONS, which was mailed in January, were distributed : TRANSACTIONS, Volume 73, 1241 pages, covering papers on non-ferrous metallurgy, milling and concentration, non-metallic minerals, iron and steel, and the Institute of Metals Division papers read at the

Jan 1, 1928

By H. B. Smith, B. Egererg

In a previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature between 200" and 450" F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress — tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy. Tensile and Bend Tests Two ingots 73/4 in. wide, 11 in. long and ¾ in. thick were cast from the same pot. One ingot was cold-rolled in one direction to a strip 0.241 in. thick, which furnished the tensile test specimens; the other ingot was rolled in the same way to 0.253 in. and furnished the specimens for the bend tests. The ingots were cast as described in the previous paper and cold-rolled in six passes.

Jan 1, 1930

By C. A. Stout, S. W. Nicksic

The materials that stubilize emulsions of some Southern California crude oils were isolated from the produced crude. These substances were separated into acidic and nonionic fractions by ion exchange chromatography. Each fraction was further broken into groups of homogeneous molecular weight composition by gel permeation chromatography. Both ionic character and molecular weight of the individual fractions are reflected in the properties of the original crude oil emulsion. Specifically, the more acidic and the higher molecular weight fractions appear to be the most effective stabilizers. INTRODUCTION The treatment of oilfield emulsions is a continuing problem for the oil industry. In almost all cases, these are water-in-oil emulsions. Much more is known about the formation and stabilization of oil-in-water (O/W) emulsions than of the water-in-oil (W/O) type. To understand W/O emulsions, more information is needed on the materials responsible for their formation and stabilization. This is especially true in the case of oilfield emulsions where the stabilizing materials are complex mixtures of large asphaltene-like molecules. To study the chemical and physical properties of these emulsion stabilizers, it is necessary first to separate them from crude oil. This separation was achieved in the case of two Southern California crude oils. The materials that were isolated appear at first to be little different from an asphaltene mixture. However, if a mixture of distilled water and mineral oil containing about 1 percent of the natural emulsion stabilizers is passed through a colloid mill, the W/O emulsion formed may be stored in the laboratory for many months without any sign of breaking. This could not be done using undifferentiated asphaltenes from the same wells, indicating that there is a real difference between these materials and ordinary asphaltenes. The colloid mill used to generate the emulsion was required because tile natural emulsion stabilizers had very little effect on oil-water interfacial tension. The one characteristic — complexity of composition — that emulsion stabilizers share with asphaltenes makes virtually impossible the exact structure determination of the components of the mixture. For this reason, it was decided to investigate first the influence of molecular weight on the ability of these materials to stabilize emulsions. The emulsion stabilizers were first separated into acidic and neutral fractions according to whether or not the material was retained on a weakly basic ion exchange column. The extraction procedure was not designed to remove basic components from tile oils, and no attempt to isolate such a fraction was made. Following this separation, selected fractions were analyzed by gel permeation chromatography. Gel permeation separates according to molecular size, largely independently of chemical or polar characteristics. A heterogeneous mixture is separated into a number of fractions having much more homogeneous molecular weight distribution. A number average molecular weight of each fraction is therefore close to the true molecular weight of the principal component of that fraction. The fraction weights, expressed as weight percent of the sample, and the number average molecular weight of a representative selection of the fractions, will be referred to in this paper as the molecular weight profile of the original sample. DESCRIPTION OF GEL PERMEATION ANALYSIS The first reported gel permeation analyses were for separating partially hydrolyzed protein molecules in an aqueous system using expanded starch granules. Most of the theoretical work on gel permeation has been done by biochemists.1 This theoretical treatment is still incomplete, but the

Jan 1, 1969

By A. J. Strauss

The solubilily of lead in PbS as a funclion of lemperature has been investigated by means of Hall coej'icient (RH) measurentents OIL samples prepared by annealing and quenching Bridgman-grourz single crystals, which contain excess lead incorporated during /heir growth from the mell. For sufficiently long annealing times and sufficiently rapid quench rules, the samples obtained consist of n-lybe PbS snturated with In the semiconducting compounds PbS, PbSe, and PbTe, the point defects associated with the presence of lead in excess of the stoichio metric composition are shallow donors. The defects associated with the presence of excess nonmetal are shallow acceptors. lead at the annealing teuiperatiire, together luilh a dispersed second phase of lead microprecipitates. Due to the retrograde solubility of lead, the measured free carrier concentration (n = l/eR77) decreases with decreasing annealing tewperature (T) from- 2.4 X 10 em-3 for 1l85OK to 1.3 X 1018 cm-3 for 623°K. The dala are well-represented by the equation n =(1.08 x 102) exp[ - (0.37 ev.)/kT] cm-3 For most undoped samples of these compounds, the carrier concentration at room temperature and below is determined primarily by the stoichiometry, since the concentration of either excess lead or excess non-metal is large compared to the concentrations of intrinsic carriers and electrically active impurities. Therefore the dependence of composition in temperature and partial pressure can be investigated by means of Hall coefficient measurements, even though the deviations from stoichiometry do not exceed 0.03 at. Pct

Jan 1, 1968

By M. Semchyshen, A. P. Coldren, W. G. Scholz

A survey of the Fe-Mo-B system was made to determine the extent to which boron might affect the microstructure and strength properties of iron-rich Fe-Mo alloys. Seventeen vacuum-induc tion melted ingots were prepared with approximate mo-lybednum contents 01 2, 4, 9, and 19 wt pct and approximate boron contents of 5, 14,50, and 630 ppm by weight. Phases extracted from annealed specimens and identified by X-ray diffraction analysis included E Fe3MO2, Mo2FeB2, and an oxide hazling a diffraction pattern practically identical to that of MnFez04. Three types of alloy strengthening were observed: a) Fe-2 pct Mo-B alloys were hardenable by a bainitic-type transformtion of austenite to ferrile; b) Fe-4 pct Mo-B alloys were hardened by the solid-solution mechanism; and C) Fe-9 pct Mo-B and Fe-19 pct Mo-B alloys were hardened by precipitation of the E Fe3Moz phase. Boron was observed to have a very strong hardening effect in the Fe-2 pct Mo alloys and a mild strengthening effect on the 1200°F properties of the Fe-4 pct Mo alloys. In the Fe-9 pct Mo alloys there was no consistent effect of boron on strength at either room temperature or 1200° F. The Fe-19 pct Mo alloys were so brittle that meaningful tensile or creep-rupture data could not he obtained. No dispersion hardening from borides was recognized in any of the alloys. THE high-temperature properties of iron-rich Fe-Mo alloys were studied by Reiter and Hibbard.' They found that the strength of the alloys increased markedly as the molybdenum content was raised from 0 to 15.9 pct by weight. The authors explained the various degrees of strengthening in terms of a) solid-solution strengthening, b) strengthening from a martensitic-type transformation, and C) precipitation strengthening. The objective of the present investigation was to conduct a survey of the iron-rich portion of the Fe-Mo-B system to determine whether the beneficial effects of molybdenum on the strength of iron can be enhanced by the presence of boron. It was thought that perhaps fine dispersions of molybdenum- rich borides would be found which could improve the high-temperature strength of ferritic alloys beyond the strengths attainable by molybdenum additions alone. Also, it was considered worthwhile to study the effects of boron in alloys which are essentially free of carbon. Most, if not all, of our present knowledge about boron in high-temperature alloys pertains to alloys containing carbon and carbides. EXPERIMENTAL PROCEDURES Alloy Preparation. Seventeen 8-lb ingots were prepared from electrolytic Plastiron, unalloyed molybdenum chips, and boron powder by a vacuum-induction melting procedure employing hydrogen as the main deoxidizer. The alloys were melted in alumina crucibles using 35-lb melts, with each melt being split four ways to achieve varying boron contents within four Fe-Mo base compositions. The results of chemical analyses conducted on chips machined from the chilled ends of the ingots are presented in Table I. The boron analyses were performed by a spectrographic method utilizing primary standards prepared from boric acid. They indicated that in ingots to which no boron was

Jan 1, 1964

By J. W. Walker, G. J. Heuer, E. W. Hough

An improved apparatus is described for the deterrni-nation of interfacial tension* by the pendant drop method in the pressure range from 15 to 15000 psi and the temperature range from 100º td 280°F. The chief characteristics of this apparatus are reliability and ease of operation. Temperature control was accomplished by means of an electrically heated jacket which could he completely removed while cleaning the apptrratus. The cell was designed so that the camera could he placed about I in, from the window without overheating the carnera lens. Separate "0" rings employed to seal each window and corresponding window backup plate gave very reliable window operation at 10,000 psi. An extra pistorr-cylinder combination was added so that a high compression ratio could he attained when gas was employed as one phase in the pendant drop cell. Other essential parts of the system were similar to an apparatus already described.' The interfacial tension for carbon dioxide and water varies from about 69 dynes/cm at 15 psi to about 19 dynes/cm at 1,250 psi for 100°F. For pressure.r between t,500 and 3,500 psi, the interfacial tension is between 32 and 24 dynes/cm at this temperature. The interfacial tension at 280°F varies from about 50 dynes/cm at 200 psi to about 17 dynes /cm at 10,000 psi. The maximum surface excess for carbon dioxide, assuming the surface excess of water to be zero, occurs at about 1,500 psi jor the 100°F isotherni and Itas a value of about -79 X 1014 mol/sq cm. At 160°F this maximum IS shifted to about 2,000 psi and has a value of about 10 X 1014 111ol/.sq cm. Other maxima, us well as several minima, are present at these and other temperatures. Judging from the data on the solubility of water in carbon dioxide at elevtrted pressures2,3, it appears that the principal maxinza natned are in regions of increasing solubility of the water in the carbon dioxide rich phase. INTRODUCTION AND APPARATUS A pendant drop interfacial tension apparatus which would accommodate an opaque liquid in a gas phase was constructed several ycars ago' for industrial purposes. This apparatus was used as a starting point for the present development. The objective of the present development was to enhance reliability and convenience of operation. Other articles'" have described pendant drop apparatus which could not accommodate a gaseous phase adjacent to the windows. A schematic diagram of the apparatus is shown in Fig. 1. The water used followed the path; A, intro-

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By L. D. Lamont, W. C. Muehlhof

Throughout the anthracite industry's history, the problem of handling and disposing of refuse material has been one of major importance. In the early days of the industry's activities, only the large sizes of anthracite were satisfactory for market requirements and the smaller sizes were deposited as refuse. As time went by, more efficient coal-burning equipment was developed and a market demand was created for the finer sizes of coal. This demand made it possible to recover marketable coal from banks deposited as refuse in the earlier days of mining. The same condition holds good today and we can see a definite trend toward the objective of utilizing the No. 4 and No. 5 buckwheat sizes. Under present conditions, we know that a limited market exists for No. 4 and 5 buckwheat; we know that the finer sizes of anthracite can be burned as pulverized fuel; we know that these fine sizes can be processed and sold as briquettes, and we also know that the heat content of these fine sizes of coal is comparable with that of the sizes now merchandized. Therefore, it should be the objective of the industry to conserve these fine sizes of coal in such manner that if and when processing facilities are developed, and market demands exist, the material can be salvaged and made available to meet these demands. From the standpoint of economical future reclamation, the ideal method of disposing of refuse containing the finer sizes of coal is to deposit it in banks separate and apart from other breaker refuse. By this procedure, the minimum amount of material will be processed in future salvage operations to recover the No. 4 and No. 5 buckwheat sizes. Many collieries in the anthracite region are operated under leases that have a specific term. These lease agreements provide that, upon expiration of the lease by term, exhaustion or otherwise, the ownership of the refuse material reverts to the lessor. Therefore, a question was raised in the minds of these operators: Why should I assume the expense of such procedure when I have no assurance that I will benefit by the future processing and sale of these fine sizes? Under present conditions, the answer to this question is not one of choice but of necessity, as restrictions imposed by legislation make it mandatory on operators of preparation plants to take necessary steps to properly treat silt-laden waters before permitting them to enter the streams. By reason of these restrictions, the disposal of fine sizes becomes a secondary rather than a primary operating consideration, and the procedure for disposing of this refuse becomes a matter of choice governed principally by topographical and geographical conditions. Methods of Handling Refuse There are three principal methods of handling and disposing of fine-size refuse; namely:

Jan 1, 1947

By W. C. Muehlhof, L. D. Lamont

Throughout the anthracite industry's history, the problem of handling and disposing of refuse material has been one of major importance. In the early days of the industry's activities, only the large sizes of anthracite were satisfactory for market requirements and the smaller sizes were deposited as refuse. As time went by, more efficient coal-burning equipment was developed and a market demand was created for the finer sizes of coal. This demand made it possible to recover marketable coal from banks deposited as refuse in the earlier days of mining. The same condition holds good today and we can see a definite trend toward the objective of utilizing the No. 4 and No. 5 buckwheat sizes. Under present conditions, we know that a limited market exists for No. 4 and 5 buckwheat; we know that the finer sizes of anthracite can be burned as pulverized fuel; we know that these fine sizes can be processed and sold as briquettes, and we also know that the heat content of these fine sizes of coal is comparable with that of the sizes now merchandized. Therefore, it should be the objective of the industry to conserve these fine sizes of coal in such manner that if and when processing facilities are developed, and market demands exist, the material can be salvaged and made available to meet these demands. From the standpoint of economical future reclamation, the ideal method of disposing of refuse containing the finer sizes of coal is to deposit it in banks separate and apart from other breaker refuse. By this procedure, the minimum amount of material will be processed in future salvage operations to recover the No. 4 and No. 5 buckwheat sizes. Many collieries in the anthracite region are operated under leases that have a specific term. These lease agreements provide that, upon expiration of the lease by term, exhaustion or otherwise, the ownership of the refuse material reverts to the lessor. Therefore, a question was raised in the minds of these operators: Why should I assume the expense of such procedure when I have no assurance that I will benefit by the future processing and sale of these fine sizes? Under present conditions, the answer to this question is not one of choice but of necessity, as restrictions imposed by legislation make it mandatory on operators of preparation plants to take necessary steps to properly treat silt-laden waters before permitting them to enter the streams. By reason of these restrictions, the disposal of fine sizes becomes a secondary rather than a primary operating consideration, and the procedure for disposing of this refuse becomes a matter of choice governed principally by topographical and geographical conditions. Methods of Handling Refuse There are three principal methods of handling and disposing of fine-size refuse; namely:

Jan 1, 1947

By L. E. Mannion

Sodium carbonate or soda ash is one of the two principal alkalis of commerce, the other being sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines or solid salts were the source of impure soda for glass manufacture. In early modern times until the 19th century, soda ash, as well as potash, was recovered mainly by leaching the ashes of plants. In Europe, during the 18th century, a brown lye for laundering was produced by pouring hot water over burned seaweed. One of the better grades of this kind of material was a product from Spain termed "barilla," which analyzed 24 to 30% Na2CO3 (Hou, 1942). The birth of the modern chemical industry may be said to start with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. Although invented in France in 1691, England made the most extensive use of it. In 1863 Ernst Solvay devised the ammonia-soda or Solvay process, and by 1874 the first of many Solvay plants was built. These were to supplant the LeBlanc method and dominate soda-ash production until the present time. Although of lesser importance, natural sodium carbonate deposits continued to support operations in various parts of the world. Shortages during World War II stimulated production of "natural" soda ash, particularly at Searles Lake, Calif., and at Lake Magadi, Kenya. Within the last ten years in the United States, a notable surge in production has occurred based on the vast trona deposits in Wyoming. Table 1 lists some principal producers of natural soda ash and the character of the source deposits. Uses and Specifications Sodium carbonate (Na2CO3) is a white, crystalline hygroscopic powder, an aqueous solution of which is strongly alkaline. Most commercial soda ash is a product that must meet high standards of purity and uniformity. Two forms are commonly sold: a fine, powdery material called light ash, and a more coarsely crystalline dense ash; these weigh 32 to 39 and 60 to 66 lb per cu ft, respectively. Dense ash may be produced by adding a little calcium chloride to the sodium carbonate solution to control crystal size and prevent agglomeration. Specifications and typical analyses of light and dense ash in the United States are shown in [Table 2]. Sizing generally achieves about 75% of light ash and 90% of dense ash between +30 and -100 U.S. screen mesh. World use of sodium carbonate now exceeds 24 million tpy, of which the United States produces more than 7 million tons. The market for soda ash is dominated by the glass industry, which uses almost half the supply. Inorganic chemicals, including phosphates and silicates, consume about 30%. Other principal uses include the manufacture of soaps and detergents, petroleum, caustic soda, organic chemicals, and paper; and nonferrous and ferrous metallurgy. [Fig. 1] shows the percent consumption by use of soda ash in Europe, Japan, and the United States. The price of soda ash in the United States remained relatively stable during the 1960s at about $33 per ton; in 1972 it reached $35 per ton. The price in 1975 was $42 per ton. Geology Mineralogy [Table 3] is a list of the more common sodium carbonate-bearing minerals. Anhydrous sodium carbonate is almost never found in nature; only natron, thermonatrite, and trona have been used directly as sources of sodium carbonate. At Searles Lake, burkeite and hanksite are important in the reconstitution of

Jan 1, 1975

By E. Miller, J. M. Eldridge, K. L. Komarek

Aclivilies of magnesium in liquid Alg-Si alloys have been delermined between 5 and 60 at. pcl Si, close to the melling point of Mg2Si, by an improved isopieslic melhod. Silicon specinrens, held in alumina crucibles and graplrile conlainevs of special design, were healed in a letrlpevalure gvadient and equilibrated with mag-nesilcrrl rapor in a closed lilanium system. The ther-madynamic Junctions were calculated and compared with the thermodyuamic properties of the other three mg- Gvoup IVB systems. Lattice paramelers of three Mg2X compounds were measured. The bonding in the Mg2X compounds is largely covalent with small and uarying amounts of metallic and ionic conlvibutions. The Mg-Si phase diagram1 has one congruent melting compound, Mg2Si, of essentially stoichiometric composition, two eutectics, and very limited terminal solid solubilities. Little information is available on the thermodynamic properties of this system. The free energy of formation of Mg2Si has been determined by the Knudsen cell technique2 in the range 572" to 680oC, by the transportation method3 between 858" and 950oC, and by the electromotive-force method4 in the range 400o to 600°C. Kubaschewski and villa5 and caulfield6 have measured the heat of formation of Mg2Si. An electromotive-force study of magnesium-rich liquid alloys was recently published by Sryvalin el al.7 The present investigation was undertaken to complete a general survey of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,a9,Mg-Sn,10,11 mg-Ge,12and Mg-Si. An isopiestic technique, previously developed for similar measurements on liquid Mg-sn11 and Mg-Ge alloys,12 was modified for the Mg-Si system. Specimens of the nonvolatile component, silicon, were contained in dense alumina crucibles placed inside covered graphite crucibles which were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure. The alumina crucibles prevented contact between the highly corrosive liquid Mg-Si alloys and graphite. The graphite cruci- bles effectively preserved the high-temperature equilibrium composition of the liquid alloys containing highly volatile magnesium on termination of the experiments during the quench to room temperature. EXPERIMENTAL PROCEDURE Silicon of semiconductor-grade purity (E. I. du Pont de Nemours and Co., Brevard, N.C.) and 99.99+ pct Mg (Dominion Magnesium Ltd., Toronto, Canada) were used. Graphite crucibles with press-fitted lids were machined from high-density (1.92 g per cu cm) rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The alumina crucibles had a purity of 99.7+ pct (Triangle RR grade, Morganite, Inc., Long Island City, N.Y.). In preliminary runs the liquid alloys were contained in graphite crucibles following the exact procedure developed for the Mg-Ge system.'2 These runs failed due to appreciable reaction between the molten Mg-Si alloys and graphite, and the results have been discarded. The procedure was then modified and the Mg-Si alloys were subsequently held in alumina crucibles. For most of the runs alumina crucibles of known weight and approximately 6.3 mm ID, 12.5 mm height, 1.0 mm wall thickness were loaded with weighed amounts of silicon and encapsuled in tightly covered weighed graphite crucibles 5/16 in. ID, 2 in. helght, 3/32 in. wall thickness). The graphite crucibles were machined from rods which were 85 pct of the theoretical density. These crucibles were therefore sufficiently porous so as to permit magnesium vapor to effuse through the silicon under the experimental conditions of approximately 970O to 1220°C and 1 day equilibration time. However, negligible magnesium was lost from the crucible during the quench due to the slow effusion rate through the pores of the graphite. The inner alumina crucible prevented the liquid alloys from contacting the graphite, and the very tightly fitting graphite crucible lids served to retain any magnesium vaporizing from the alloys inside the crucibles during the quenching step.12 The loaded silicon-alumina-graphite cells were positioned, one above another, on a 16-in.-long titanium thermocouple well and tied securely to the titanium tube with thin molybdenum wires held in grooves around the circumference of the graphite crucibles. A thin (0.005-in.) molybdenum strip prevented contact between the graphite crucibles and the titanium. This assembly was lowered into a titanium reaction tube (la in. ID, 16 in. long, $ in. wall thickness) closed on one end which contained a 11/2-in.-long cylinder of magnesium at the bottom. The inner titanium thermocouple well was positioned eccentrically in the large tube because of the eccentric mounting of the cells on the well. Appropriate modifications of the titanium cap"'12 were made to join the inner and outer titanium

Jan 1, 1968

By A. W. Hesse

VENTILATION of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 19 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. VENTILATION FOR MECHANICAL LOADING IN GASSY MINES In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to by-pass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity, and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1941

By H. P. Greenwald

IN the year just passed the Coal Division's Committee on Rock-Dusting reviewed the status of this safety measure in American coal mines and prepared a paper thereon which will be presented at the February meeting of the Institute. This paper supplements one appearing in Vol. 139 of the "Transactions," page 87 (1940). Because that paper will be issued soon, only a summary is given herein.

Jan 1, 1944

By Corliss R. Kinney

SINCE the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated pace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. POSSIBILITIES OF ACETYLENE One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and' these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1946

By Paul R. Smith

Preparation for flotation begins with dragline mining, pumping, washing, screening, and desliming. Slimes, nominally -150 mesh material, constitute large quantities of phosphate and water which are a disposal problem. Older techniques involve sizing at about 35 mesh for separate coarse and fine treatment. The plus 14 mesh fraction does not require concentration. Coarse treatment includes agglomerate spiralling, belt flotation, thickening, scrubbing with sulfuric acid, de-oiling for reagent removal, and cationic flotation of fine quartz. A recent trend is to screen at coarser than 35 mesh size and eliminate coarse particle treatment, sacrificing some grade of this product. Techniques for flotation concentration of the fine size fraction are discussed.

Jan 1, 1976

By C Gunther

Mining examinations are of several kinds and the scope of the investigation depends in each case upon the purpose for which the examination is made. A formal examination of a developed mine is an expensive undertaking; from one to several months are allowed for the work according to the size of the property; many samples are taken; investigation is made of the geological features, including, perhaps, a topographical and geological survey of the surface; the metallurgical treatment of the ore is studied; finally, a determination of costs is demanded. Formal examinations are made for prospective purchasers or as a basis for the consolidation of several properties, and occasionally, in the owner's behalf, to verify the work of resident engineers, or to determine the readiness of a mine for equipment and the kind and capacity of equipment it shall receive. A formal examination of a mine should not be undertaken until a preliminary examination has shown that it is justified. It is regrettable that some engineers are in the habit of prosecuting long and exhaustive examinations of properties whose lack of merit should be, and perhaps is, apparent from the start, or of continuing their investigation long after an unfavorable result is seen to be inevitable. This wasting of a client's money is a species of trickery difficult to prove, and therefore the more contemptible. Preliminary examinations are precisely what the term implies, and are undertaken to determine the advisability of making

Jan 1, 1932

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to '939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942