Search Documents

By Jasper Stuckey

THE object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which-the Hot Springs and Kings Mountain -contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3 1/2 miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite-usually there have been less than three producers-and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage. was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926.

Jan 1, 1933

By Guy Crane

I. INTRODUCTION THE geology of the Tintic mining district, fully treated, would occupy an elaborate monograph. This less comprehensive paper is devoted primarily to the occurrence and origin of the orebodies of the district, while space is given to those phases of the general geology only which seem necessary to a proper setting of such a discussion. The first geological report on the Tintic district to be issued was that by Tower and Smith, published in 1899, in the form of a paper in Part III of the Nineteenth Annual Report of the U. S. Geological Survey, and also as Folio No. 65, Geologic Atlas of the United States. About four years ago a second investigation was begun by Waldemar Lindgren and G. F. Loughlin, of the U. S. Geological Survey. With the exception of a paper on the oxidized zinc ores of the Tintic district by Mr. Loughlin, the results of their work are still unpublished. The writer's acquaintance with the district began in the fall, of 1913, and has extended over a period of about two years.

Jan 10, 1915

Executive Committee, Board of Directors Howard C Pyle, Chairman, J L Gillson, Vice¬Chairman, A W Thornton, Elmer A Jones, Augustus B Kinzel Finance Committee, Board of Directors J S Vanick, Chairman, John P Hammond, J W Woomer Investments Gail F Moulton, '60, Chairman, Andrew Fletcher, '62, John M Lovejoy, '61, C R Dodson, ex off as AIME Treasurer, J S Vanick, ex off as Chairman of Finance Committee Endowment Andrew Fletcher, Chairman, N G Alford, W J Coulter, Harold Decker, J V N Dorr, R B Gilmore, J B Haffner, Kenneth Hill, 0 H Johnson, J D MacKenzie, D H McLaughlin, J R McMillan, W S Morris, L F Reinartz, H DeWitt Smith, Wilfred Sykes, J R Suman, C E Weed Honorary Memberships C E Reistle, Jr, '60, Chairman, Grover J Holt, '61, Augustus B Kmzel, '62, (ex off as Past Presidents of AIME) M L Haider, '60, D H McLaughlin, '61, John M Lovejoy, '62, L F Reinartz, '63, Howard C Pyle, ex off as President of AIME

Jan 1, 1959

THE Pacific Northwest's joint meeting of the Industrial Minerals and Metals Branch in Spokane, Wash., drew 260 members, 72 students, and 30 ladies. Theme of the meeting was to acquaint men in the industry with students and younger men. The special appeal to the students was coupled with an attempt to attract young technical men from the companies located in the northwestern area. The activities of the meeting were available without charge to students. Contributions were made by the industries in the area to assist student attendance. Following the special student and faculty trip to the Trentwood rolling mills and research laboratory on Friday afternoon everyone enjoyed a complimentary dinner. A. Y. Bethune of the Sullivan Mining Co., spoke to the group on the operations of Kellogg, Idaho electrolytic zinc plant. The Industrial Minerals Div. session was opened on Saturday morning by R. G. Vervaeke, Conference Chairman who introduced A. O. Bartell of the Raw Materials Survey, Portland, Ore. Mr. Bartell in turn introduced C. W. Sweetwood who discussed Open-Pit Phosphate Mining.

Jan 1, 1952

IN recognition of thirty-one years' service as professor of mining in McGill University the friends of Dr. Porter gave him a complimentary dinner at Montreal, on Jan. 24. The affair was appropriately held under the auspices of the Montreal Branch of the Canadian Insti-tute of Mining and Metallurgy, George C. Riley presid-ing, and was made the occasion of presentation to him of a Canadian landscape painted by Maurice Cullen, and of a silver plate to Mrs. Porter. Among those speaking were Messrs. George E. Cole, F. D. Adams, Sir Arthur Currie, W. C. McBride, and J. G. Ross. Mr. Cole spoke of the large part Professor, Porter had played in the development of mining in Canada through training the men who had become the leaders in the work. More than 200 mining engineers graduated from the University during Dr. Porter's tenure of office and while not all of them had continued to practise their profession, as a body they had had an immense influence.

Jan 2, 1928

By Alden Greninger

TWINNED metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the obser vation of the twins, there are two other possible groups: (1) solidification twins,? when observed in the as-solidified or as-cast condition, and (2) transformation twins, ? when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form {112}. Since McKeehan's discovery, little or no attention has-been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the prepara-tion of single crystals. McKeehan's twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures-at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O'Neill3. has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually

Jan 1, 1936

By William R. Webster

In view of the great interest now taken in the tests of castiron and details of foundry practice, with the number of investigators at work, and recent improvements in the methods of research, it would seem that the time is ripe to attempt the solution of some of the many problems with which iron founders have to contend. Recent papers and discussions on these subjects* have opened up s large field for investigation, and have emphasized the importance of many considerations generally overlooked. With the view of promoting a comprehensive and systematic discussion, I have attempted to tabulate, in conveilient form, some of the most important points for investigation, on the general plan suggested, with such good results, by our former President, H. M. Howe, for the discussion on the Physics of Steel, at the Virginia Beach meeting, last year. This table can, no doubt, be modified or enlarged to advantage, and put in shape to serve as a guide or reminder to all who are interested in this line of work. Suggested Lines for Discussion and Investigation. I.—Correspondence between chemical composition and melting point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: I. Cupola mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6. Kind of mould, green sand (under dif- on 1 E. Chill. ferent conditions of ramming, amount F. Residual stress. of moisture, and skin-dried), dry sand, G. Condition and quan loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum,

Jan 1, 1896

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

By G. S. Anderson

PRIOR to 1912 the only rail outlets for a large part of the coal regions of Carbon and Emery Counties. Utah, were over single-track lines of the Southern Utah R.R. and Castle Valley Ry. Companies, forming a route extending from Mohrland and Hiawatha, Utah, to a point of connection at Price, Utah, with what is now The Denver and Rio Grande Western R.R. Co. These two tap lines were poorly and inadequately constructed, with impracticable grades, lacking in equipment, and incapable of being put into condition to serve this region and handle the output of the mines, to say nothing of making possible increased production and new development. Any plans for the new development and increased output necessarily involved new and adequate railroad service. It was essential, not only that additional facilities be provided but that these facilities be in the form of an efficient and up-to-date railroad providing an independent through operation from the coal mines to a point of direct connection with the lines over which the product would be distributed to consumers. For this purpose, the Utah Railway Co. was incorporated in

Jan 1, 1948

By J. C. Yannopoulos, N. J. Themelis

Ah electronic thermogravirnetric balance was used to measure the veductioiz rule o single cirpric oxide particles suspended in a stream of hydrogen. Very jzne thermocouples embedded in lie center and at the surface of the sphere recorded the variation of terw perature during reduction. In contrast to iron oxide reduction, where in most instances the rate of interface reactiokl is controlling, the heat- and mass-transfer phenotnena play a predolrinant role in the reduction of cupric oxide. The correlation of experitnental data or tnass lransfev lhrough the boundary layer at Reynolds nunlber 0-4 50 was as jollocs: ThE reduction of cupric oxide by hydrogen is represented by the equation: It is a highly exothermic reaction and the amount of heat released varies only slightly with temperature (-21,430 cal per g-mole at 400°C). Most of the published studies on this system have been conducted at temperatures in the range of 34 to 280c.l-&apos; The concensus of opinion has been that at temperatures below 200°C the reaction is preceded by an induction period during which there is very little or no reduction. The length of this period diminishes as the temperature of the reaction is increased1l5 and aseawa found that at 280°C reduction starts practically immediately when the oxide is exposed to hydrogen gas. The existence of an induction, or incubation, period has led experimenters to believe that the reduction of CuO by hydrogen is catalyzed by metallic copper.&apos; Boldurev and rmolaev found that mechanical additions of powdered copper to oxide did not affect its reduction, although metallic copper produced during the reduction seemed to have a catalytic effect. At least three other authors2&apos;5&apos;7 have reported that addition of copper had no effect on the rate of reduction. Pease and alor&apos; observed that water vapor had a strong inhibiting effect on the reduction at 1503C, but its effect was greatly diminished at 200 C. Pavlychenko and Rubinchik5 studied this reaction at 159 to 235 C and found that, once the reaction had been initiated, there was no inhibiting effect due to the introduction of water in the hydrogen stream; at temperatures above 183°C there was no inhibiting effect due to water vapor, either before or during reaction. The same authors noted that the rate of reduction was independent of pressure in the range of 200 to 700 mm Hg. aseawa investigated the kinetics of the CuO-Hz system at 160 to 280°C and estimated the apparent activation energy at 14,000 cal per g-mole. A similar value (13,500 1200 cal per g-mole) was reported by ond&apos; in the temperature range 148 to 216°C. Bond also reported that there was no incubation period and that water vapor had no inhibiting effect on reduction at temperatures above 190 C. The above studies have been conducted at temperatures below 280°C and the physical configuration of the system under investigation has not been defined adequately. However, it is well-known that the mechanism of gas-solid reactions depends on a number of in series physical and chemical rate prcesses.&apos;&apos; It is, therefore, essential to include among the experimental factors the geometry of the solid system and the mass-transport characteristics of the reducing gas. Scott studied the reduction of packed beds of cupric oxide cylinders by Hz-He streams of very low hydrogen concentrations at temperatures 400 to 600 C, pressure of 10 to 30 atm, and gas velocity from 0.18 to 5.8 ft per sec (3 < Rep < 30). The reduction rate was found to be mainly controlled by diffusion through the boundary layer and through the pores of the reduced copper phase. The following correlation was proposed: Scott in an earlier work studied the reduction of fixed beds of cupric oxide wire and found that the rate of flow of the gas stream through the bed had a controlling effect on the rate of reduction. The same mass-transfer phenomenon was observed by Bond and clark13 on a similar reduction system. The analogy between mass and heat transfer through the boundary layer which exists between a solid surface and the bulk stream stems from the similarity of the differential equations representing these phenomena

Jan 1, 1967

By W. O. Philbrook, L. D. Kirkbride

IN the normal operation of the iron blast furnace, reduction of the iron oxides is accomplished almost entirely above the tuyeres.&apos; Blast furnace slags usually contain less than 0.5 pct FeO, although higher values may occur with abnormal operation. There is reason to conjecture, however, that incompletely reduced ore may sometimes reach the hearth and enter the slag as a result of heavy slips or, perhaps, even from cores of excessively large lumps of a charge material of poor reducibility. The possibility of reoxidation of iron droplets falling in front of the tuyeres has been considered by several writers. It would be of interest, to know how rapidly iron oxides reaching the slag for any of these reasons could be reduced by reaction with coke or with the high carbon liquid iron in the hearth. In comparison with the hundreds of papers that have appeared on various aspects of the reduction of solid iron oxides by gases and in the presence of several forms of carbon, little work has been published on the reductioin of liquid oxides or slags. Dancey measured rates of reaction of the pure liquid oxides, both FeO and Fe,O,, with molten iron containing about 4.3 pct C. The oxide was dropped into the cup formed in the upper surface of the iron by rotating the crucible and melt. Under these conditions, reduction of either FeO or Fe,O., was completed in less than 10 sec. The present study was concerned with the reduction of FeO from blast furnace-type slags containing less than 5 pct FeO and melted over carbon-saturated iron in stationary graphite crucibles. The results were considerably different from those found by Dancey, as will be discussed later. Although this work is of interest in relation to hearth reactions in the blast furnace, interpretations must be made with caution because the experimental conditions do not duplicate those within a furnace and may not even lead to the same reaction mechanism. The authors were motivated in undertaking this work by an additional interest—the part played by FeO reduction in the mechanism of de-sulphurization of iron by slags under similar experimental conditions. Derge, Philbrook, and Goldman eveloped detailed experimental evidence to support a three-step mechanism for desulphurization like that originally proposed by Holbrook and Joseph&apos; (These reactions are written in molecular form for convenience, but this is not intended to imply the existence of molecules of FeS in the bulk metal phase nor to deny the likelihood of ionic reactions in the slag.) Earlier work by Chang and Goldman" had shown that the overall reaction follows first-order kinetics with respect to sulphur and that the rate of reaction is proportional to the slag-metal interface area, which observations have been confirmed by subsequent work. Later studiese,&apos; have established the influence of al.loying elements on the first and last steps of the reaction. This paper reports a study of step 3 alone, uncomplicated by the simultaneous process of sulphur transfer. Apparatus and Procedure The experiments were made in a conventional high frequency induction furnace powered by a 35 kva Hg spark gap converter. The graphite crucibles used for most of the runs were 14 cm (5.5 in.) deep and 4.8 cm (1.9 in.) ID with 0.75 cm (0.3 in.) wall. An insulating cover with a small opening for withdrawing samples was used to minimize heat loss and infiltration of air into the furnace. The crucible was charged with 300 g of carbon-saturated iron and either 65 or 100 g of prefused slag analyzing 38.0 pct SiO,, 15.4 pct A10 and 47.1 pct CaO. To obtain the cleanest possible interface at the start of the reaction, the metal and slag were brought to temperature together to prevent the rejection of kish graphite that would have been caused by the chilling effect of a large addition of cold slag to carbon-saturated iron. After temperature control had been established, the desired amount of iron oxide was added in the form of a prefused slag of composition 73.6 pct FeO, 7.7 pct AWX and 19.0 pct SiOl. This slag addition was observed to be molten in somewhat less than 1 min, and a very vigorous reaction proceeded for 1 to 2 min after its introduction. Zero time was taken as 2 min after the ferrous silicate slag addition. Slag samples weighing about 0.5 g each were taken periodically by a copper chill sampler." The weight of the initial slag was large relative to the weight of samples removed, so that the slag weight never varied by more than 5 pct during any run. Temperature was measured by a calibrated W/Mo thermocouple immersed in the metal, with a graphite tip cemented over the fused silica protection tube to prevent attack by slag and metal. After some difficulties with uncertain temperatures during the first two runs, the practice adopted to position the thermocouple for reproducible results was to lower the protection tube to touch the bottom of the crucible and then raise it 0.5 cm. The apparent temperature gradient between the bottom of the crucible and the top of the slag was found to be 15°C (27°F). but much of this spread was probably the result of inadequate immersion of the protection tube to off-set conduction losses along the graphite tip when the thermocouple was inserted only into the slag. The temperature of the bath was controlled within 25°C (9°F) during a run.

Jan 1, 1957

By Clarence P. Linville

(Pittsburg Meeting, March, 1910.) IT is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition ; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which . make the fuel practically uniform ; the Gayley

Mar 1, 1910

The John Fritz Medal for the year 1917 has been awarded to Professor Henry Marion Howe for his investigations in metallurgy, especially in the metallography of iron and steel. Record of the John Fritz Medal. The John Fritz Medal Board of Award has published a book giving a history of the Medal, the Rules of Award, biographical notices of the medallists illustrated with portraits, etc. This beautiful book, designed, engraved and printed by Bartlett Orr Press, New York, may be obtained by addressing the Secretary of John Fritz Medal Board of Award, Engineering Societies&apos; Building, New York. Price $3 per copy.

Jan 3, 1917

By Roscoe C. Clark, Henry F. Coffer, J. J. Reynolds

A cement slurry lightweight additive has been adapted in the Conoco laboratories for use in oil well cements. This additive makes possible the use of air to lighten oil well cement slurries. Specifically, the additive consists of small clay bubbles of air having sufficient strength to resist crushing by bottom hole pressures. Clay bubble cement slurry weights can be safely reduced to 10 Ibs/gal. In addition, the clay bubbles tend to act as lost circulation materials and to provide a cement texture which should produce good perforating characteristics. Clay bubble cement is relatively impermeable. INTRODUCTION In many areas in Oklahoma, Texas, Wyoming, and California, difficulties are experienced during casing cementing operations with lost returns caused by the high density of the cement slurries. Wells in these areas are ordinarily drilled with 9 to 11 lbs/gal. drilling mud while neat cement slurries may range in densities from 14.5 to 17 lbs/gal. In these areas, cement slurry weights are at present being successfully reduced to around 12 lbs/gal. (under bottom-hole conditions) by the use of additives in the cement. Since the use of additives will decrease the strength which the cement will develop, the amount of additives which can be used must be based on the minimum cement strength which is acceptable; and thus the maximum slurry weight can be reduced. At present, the minimum tensile strength generally acceptable is 50 lbs/sq in. cured for 24 hours under bottom-hole temperature. This figure is based on laboratory tests1 and on a large number of cement jobs which have been conducted using cement which will not develop more than 50 psi tensile strength in 24 hours under bottom-hole conditions. Two additives are now in use for decreasing cement slurry weights. These are expanded perlite and/or bentonite. The density of both of these materials is greater than that of the cement slurry; however, large quantities of water may be added with these materials without producing a slurry which will settle out of suspension. It is these large quantities of water which contribute to the reduction in the slurry weight. The minimum slurry weight at present obtainable with expanded perlite and/or bentonite is approximately 12 lbs/gal. using a standard Portland cement slurry. In many areas, this weight reduction is insufficient; and returns are still lost during casing cementing operations. In many cases, the pay formation itself is fractured; and a considerable quantity of this cement is lost to the pay zone. It is therefore believed that if cement slurry weights can be reduced to as low as 10 lbs/gal., two advantages will accrue: 1. The lighter densities (10 to 12 lbs/gal.) should mitigate or eliminate lost returns during casing cementing operations. 2. Cement slurries above 12 Ibs/gal. (the present minimum limit ) should develop considerably more strength than is now being obtained. A tensile strength of 100 psi is desirable.&apos; It is the object of this paper to describe a cement slurry having a weight of 10 lbs/gal. and capable of

Jan 1, 1955

Furnace Builder. Engineer with extensive experience in furnace building. Position with well-established firm, branching into new fields. Location Ohio. 11-1343. Erecting and Operating Engineer to take charge of erection of gas-producer equipment and to teach customers how to operate such equipment. Location Ohio. Salary $250 per month. R-1339. Assistant Professor in Mining School, for instruction work; must have had experience in ore dressing and metallurgy. Location Missouri. Salary $1500-$2100 per school year (8 mo.). R-1332. Consulting Engineer, familiar with construction of artesian wells to act in a consulting capacity. Location New York City. R-1324. Mining Engineer and Investigator to do non-metallic mineral investigations in both field and office for United States Government. Position will last at least a year, and may become permanent. Location Washington, D. C. Salary $1800-$2700 depending on qualifications of appointee. R.-1317. Crushing Plant Superintendent, cement mill and construction experience essential. Prefer man who has had limestone crushing experience. Location New York. R-1314. Assistant Professor of Coal Mining, must be a graduate of mining engineering and have had some coal mining experience. Location Philadelphia.. Salary $2200 for school year of 10 months. R-1312.

Jan 9, 1919

By H. W. Hitzrot

The new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure—the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, and not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct

Jan 1, 1939

By H. W. Hitzrot

The new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure—the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, and not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct

Jan 1, 1939