Search Documents

By H. M. Otte

Certain choices for the shear elements of the inhomogeneous distortion in the phenomenological theory of martensite formation are examined for their agreement with crystallographic and X-ray data of iron alloys. The assumption that the shear elements must represent slip or twinning systems characteristic of bcc metals is found to covey all observations, even when a small uniform dilatation is taken into consideration. In bct martensite, (011) becomes a possible twinning or faulting plane, in addition to {112), and qualitatively similar X-ray line broadening is to be expected from both. The basic concept inherent in the current theoriesl-4 of the formation of martensite is that the interface between the parent (austenitic) and product (martensitic) phase is an invariant strain plane (i.e., one that is undistorted and unrotated). Experimental evidence that the interface is of such a nature is available in certain transformations2'5'6 but for the transformation in iron alloys direct observation has not proved enlightening. Internal strains resulting from the formation of the small martensite platelets within the parent austenite matrix7 make it difficult to produce the desired evidence. Indirect evidence, however, such as the continuity of scratches in passing from untrans-formed to a transformed region, strongly indicates that the habit plane in iron alloys is an invariant strain interface. The scatter in habit planes in a given specimen8 would suggest that internal stresses have a slight but definite influence. On the other hand, composition changes which affect the lattice parameter can alter the habit plane appreciably, and by an amount greater than the scatter.' The success of the theories depends on the choice made for the "inhomogeneous distortion" or "complementary shear'' in the analysis and also on the choice for the parameter 6 representing a small uniform dilatation. In the approach developed by Wechsler, Lieberman, and Read'," it is implicitly assumed that 6 is unity. In the case of iron alloys, all observations cannot be explained without varying either the inhomogeneous distortion or 6 . Bowles and Mackenzie3 considered only the effect of varying d. They found it difficult to reconcile the wide scatter of habit planes with the theory and were forced to the conclusion that it may also be necessary to consider variations or different choices of the inhomogeneous distortion. Wechsler and Read" considered a limited number of possible choices for the inhomogeneous distortion, but no variation in 6, though this could easily have been introduced if so desired. It is the purpose of the

Jan 1, 1961

By Charles Clayton

A study of the literature shows that the greater part of research work on annealing of cold-worked iron has been for the purpose of studying the effect on grain-size and properties other than hardness. No reference has been found of experimental work of the same nature as that explained in this short paper. The material used throughout was Vismera iron, an iron containing 0.03 carbon and made several years ago by the Inland Steel Co. One-half inch stock was cut into cylinders ¾ in. long. The cylinders were then compressed for 60 sec. in a Reihle testing machine under loads as indicated below: COMPRESSION, AVERAGE LENGTH, SERIES POUNDS INCHES 1 10,000 0.693 2 15,000 .599 3 20,000 .501 4 25,000 .426 5 30,000 .378 6 35,000 .351 7 40,000 .311 Fig. 1 shows these cylinders after compression. Each series con¬sisted of 17 specimens lettered 0, B, C, D, E, E:, G, H, I, J, K, L, M, N, P, Q, and R. One specimen of each series was reserved for study of the properties in the cold-worked condition. The other specimens were annealed in a Hump furnace for ½ hr. at the following temperatures:

Jan 2, 1926

By H. Q. Golder

INTRODUCTION The stabilization of slopes is not a design problem. A slope is designed before it is made. For a slope to be stabilized it must already exist. The basic problem has existed for a long time. It started with cuts in soil and rock made in the 18th century during the construction of the canals which were developed at that time, and continued into the 19th century with the development of the railways, and in the 20th century with motor roads and lately open pit mining. It is not difficult to stabilize a slope, but certain questions must be asked and answered. These are: i) How much stability is required? ii) For how long is it required? iii) How important is the cost? These three questions indicate the basic problem of Civil Engineering, which is that the solution to any problem is a compromise between safety, cost and time. Stabilization of slopes is no exception. If the slope exists why is stabilization a problem? There are many possible reasons, for instance, a neighbouring and similar slope may have failed, or it may be necessary to change the conditions of the slope, steepen it, increase its height, put weight at the top, or construct a building at the foot in which case added security is required, or guarantee its stability for a longer time. MECHANISM OF FAILURE In order to pick the correct method of stabilization the mechanism of failure must be understood and the immediate cause of failure known. Often to remove the cause is the best remedy. The mechanism of failure has been studied over a period of many years in landslide problems. Pit slope failures are very similar to some types of landslides. (1) (2) (3) (4) In one sense there are many causes of landslides. Terzaghi lists 19. This means that there cannot be a standard solution to a stabilization problem. In another sense, it can be said that there is only one cause, which is gravity. This is a constant, never failing force which cannot be

Jan 1, 1971

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By W. N. Logan

WHAT is mineral wool? This question is frequently asked by those unacquainted with its manufacture. The word "mineral" suggests that it is of mineral origin; the word "wool" suggests that it is of animal origin; but the only similarities it has to wool are its fibrous character and its white fleecyness. Mineral wool is a fiber produced by melting rock to a glasslike condition and blowing the glass into fine white, wool-like threads. A -number of the products fabricated from-mineral wool are used for some form of insulation, but mineral wool is adaptable to many other uses. It is used in the manufacture-of pipe covering designed to with; stand the high temperatures produced in steam pipes. In a similar form of insulation it is used to cover boilers and furnaces. It is used in ,the fabrication of upholstery tow for sofas and car seats: In acoustics it has many uses, such as acoustifibroblock, which is used in floors to destroy sound and vibration, and acoustic mat, which is used under carpets to destroy sound. In the insulation of houses, loose wool and granulated wool are used beneath attic floors and between the studding in frame buildings to prevent the escape of heat in winter and the entrance of heat in summer. Mineral wool is used also in fabrication of linofelt, which is a quilted form of insulation; in fibrofelt, which is an insulating board; in the fabrication of lith, which is an insulating block; in anti-fibroblock ,which is used in insulation and refrigeration; in flexfelt; in loose wool; in pressed block; in heavy oiled wool; in dark oiled block; and for many other purposes. The materials used in the manufacture of mineral wool are of two kinds. The first is a rock which contains silt, clay and silica, with smaller amounts of lime and magnesia. The second is a more highly calcareous rock which may carry a small amount of magnesia. The latter is used as flux to assist in the melting of the former. The relative proportion of the alumina-iron-silica content to the lime-magnesia content is normally as fifty to fifty but a considerable range is possible.

Jan 1, 1932

By V. Lessels, D. J. Buckwalter, D. H. Rose

At White Pine Copper Co.'s operation in the Upper Peninsula of Michigan, the company has been losing more than four lbs of copper in each ton of sand tailings. With an average rate of 12,000 tpd of sand going to the tailing pond daily, the company has been losing more than 14 million lbs of the red metal annually. With an eye aimed toward lessening this loss, White Pine engineers in 1959 initiated a study on techniques for recovering this "lost" copper from the sands. Inasmuch as the flotation operation was considered to be optimized, a logical approach seemed to be leaching. For various reasons ammonia, ferric chloride, acid, and biological leaching were ruled out as impracticable. This led to a consideration of cyanide leaching as practiced in the precious metals industry.

Jan 8, 1967

By George M. Schwartz, Ian L. Reid

THE Soudan mine in the Vermilion district of northeastern Minnesota is the oldest iron mine in the state. It has shipped ore every year since 1884 and still contributes a yearly quota of high grade lump ore. No comprehensive report on the Vermilion iron-bearing district has appeared since Clements' monograph,' but Gruner2 discussed the possible origin of the ores in 1926, 1930, and 1932, and recently Reid and Hustad have added data on mining and geology .3, 4 For many years geologists of the Oliver Iron Mining Div., U. S. Steel Corp., have kept up to date a series of plans and vertical sections of the Soudan mine. In connection with mine operation considerable diamond drilling has been done, and this, together with the mine openings, has permitted a reasonably accurate picture of the structure of the orebodies and wall rocks. It has long been evident to geologists familiar with the mine that the ores were not a result of weathering, a point emphasized by Gruner in 1926 and 1930. As the deeper orebodies were developed it also became clear that replacement had played an important part in their development. In recent years it has been recognized that other iron ores were formed by replacement, as Roberts and Bartly5 have argued strongly for the deposits at Steep Rock Lake. On the basis of these facts G. M. Schwartz suggested to members of the Oliver staff that it would be desirable to study the evidence of replacement, particularly the possible alteration of the wall rock which would be expected if the replacement was a result of hypogene solutions. Rock Formations: The formations directly involved in the iron orebodies of the Soudan mine are few though far from simple. The country rock is largely the Ely greenstone of Keewatin age consisting of a mass of metamorphosed lava flows, tuffs, and intrusives which have been more or less altered by hydrothermal solutions. The predominant rock is chlorite schist. Interbedded with the original flows and tuffs are a series of beds and lenses of jasper to which the name Soudan formation has been applied. In the Vermilion district the term jaspilite has been used for interbanded jasper and hematite. According to modern usage these jasper or jaspilite beds do not comprise a formation separate from the Ely greenstone, inasmuch as the beds of jasper are interbedded with the flows and tuffs of the upper part of the greenstone. It would more nearly accord with modern usage to consider the Soudan beds a member of the upper part of the Ely formation. Because of incomplete rock exposure and exploration the number of interbedded jaspilite beds is unknown. In the mine, however, as many as nine major beds of jasper are known on a cross-section of one limb of the syncline, with an equal number on the other limb. In addition diamond drill cores show beds of greenstone down to half an inch in thickness. The thin beds are probably always tuffs. Structure: Rock structure in the Soudan area is complex, and because there are no recognizable horizons within the greenstone it is extremely difficult to work out the details. Generally speaking, the major regional structure is an anticlinorium, the axis trending east-west, with a westerly pitch. The Soudan mine is related to a synclinal structure on the north limb of the anticline about a mile from the west nose of the folded iron formation. The general structure at the mine is that of a closely folded minor syncline on the major regional anticline. A cross fault has dropped the east side so that the bottom of the syncline has not been reached, whereas to the west it is well shown by the mine openings and diamond drill exploration. Throughout the mine the beds of jasper, and ore-bodies that have replaced the jasper, normally dip northward at angles of 80" or steeper. In detail the jasper beds are extremely folded, probably as a result of deformation while they were still relatively unconsolidated. Orebodies: Ore in the Soudan mine is mainly a hard, dense, bluish hematite. Locally ore has been brecciated and cemented by quartz. The vugs commonly occurring near the borders of orebodies are lined with quartz crystals. They seem to have formed as part of the ore-forming process and are evidence that no folding or compression of the ore has taken place. The orebodies are numerous, varying greatly in size. Many lenses of high grade hematite are too small to be mined. Some of the larger orebodies have been followed vertically for as much as 2500 ft and horizontally up to 1500 ft. The large ore-bodies are extremely irregular in outline in the plane of the beds of jaspilite. In width they are more regular, as they are strictly governed by the width of the jaspilite beds and the greenstone wall rock, which seems to have resisted replacement by hematite. At many places the orebodies replace the jaspilite completely and have a footwall and hanging wall of greenstone. At other places either one or both walls may be jaspilite. Geologists who have studied the orebodies in recent years agree that evidence for the replacement origin of the hematite bodies seems conclusive. AS noted above, many of the orebodies replace jaspilite beds from wall to wall with no evidence whatever of compaction. The replacement origin is also supported by details of the banding which is characteristic of the

Jan 1, 1956

By M. L. Holzworth, Joseph C. Kremer, Paul A. Beck, L. J. Demer

FOR alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystallization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig r shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hrs. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b. It is seen that for any annealing temperature below T. the grain size was smaller than in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T. the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T, or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig 11 by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has has been most frequently and best investigated in brass. This type has been designated as "normal grain growth," while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1947

By John Dilworth

THIS paper treats primarily of the valuation of developed coal properties by the method of capitalizing their estimated average future earnings. However, in it reference is also made to valuations of undeveloped coal lands and to various methods of appraisal other than by future earnings. FUNDAMENTAL VALUATION PRINCIPLES Before discussing in detail coal property valuations, a few statements bearing on the general subject will be made to present certain of the writer's views on the question as a whole. 1. A certain property at a given time has but, one true value. This is not universally admitted. The appraiser rather frequently finds that a coal owner has in mind three valuations for his holdings; one, the figure at which he feels they should be appraised for taxation purposes; another, the much higher one that should be used if a loan is to he negotiated on the property; and a third, intermediate between the other two, the price for which he would be willing to dispose of his holdings were they for sale. The last is usually nearest to the true value, and because this is so the statement is generally accepted that the fair value of such a property is the price arrived at by negotiation between a willing seller and a willing buyer who are otherwise disinterested. 2. Notwithstanding the foregoing, it is only very generally and approximately true that the proper measure of the value of a given developed1 coal acreage is the unit or per-acre price for which one or more bodies of similar coal in the salve district have been sold recently. To give a few reasons why such a measure of value can not be strictly applied, it may be noted:

Jan 1, 1927

By L. M. Pidgeon, K. T. Aust

There has been considerable interest in the possible use of titanium in magnesium alloys.' Zirconium has shown some promise in this connection2 and its general similarity with titanium suggests that the latter might act in a similar manner. A literature survey revealed that quantitative data on the Mg-Ti system was unavailable. Several patents3 have claimed that titanium additions from 0.2 to 4 pct to magnesium alloys were possible, but no mention was made as to the form in which the titanium existed in the alloy. Kro114 succeeded in introducing only traces of titanium into magnesium by bubbling TiCl4 through the metal under argon or by reacting it with sodium titanium fluoride. The application of theoretical data given by Carapella5 based on Hume-Rothery's principles, involving atomic size factor, crystal structure, valency and the electro-chemical factor, suggests that a Mg-Ti alloy is a favorable case, and the system appeared to warrant experimental examination. Experimental Procedure and Results THERMAL ANALYSIS If titanium is appreciably soluble in magnesium, a change in the melting point of the magnesium might be detectable using standard cooling curve methods. Magnesium was melted in graphite crucibles under an argon atmosphere, the assembly being enclosed in a silica tube. Graphite thermocouple protection tubes served also to stir the melts. The apparatus was very similar to Fig 1, with the addition of a refractory and baffle system to prevent undue heat losses from the top of the crucible. Chromel-alumel thermocouples were calibrated using Al of 99.97 pct purity. Dominion Magnesium Limited sup- plied redistilled high purity magnesium of the analysis given above. Titanium was added in three different forms: 1. Titanium powder —100 mesh, from the Titanium Alloy Manufacturing Co., Niagara Falls, N. Y. 2. Sheet titanium from the U.S. Bureau of Mines, produced by Mg reduction of TiCl4. 3. Magnesium —50 pct titanium master alloy from Metal Hydrides Inc., Beverly, Mass. The melting point of the high purity magnesium used was measured experimentally as 651.0°C. More than a dozen tests were conducted using titanium from the three sources referred to above, in calculated additions up to 20 pct titanium, at temperatures between the melting point and 1000°C and holding periods up to 6 hr. In no case was evidence obtained of solubility of titanium in magnesium, using inverse-rate and time-temperature curves. The melting point of the magnesium was unchanged within the accuracy of measurement, namely -+0.5°C; and no other thermal arrests were detected. Metallographic investigation of the thermal analysis billets indicated that the titanium additions were apparently mechanically entrapped in the magnesium in segregated areas. Consequently, these samples were not analyzed for titanium. The master alloy proved to be a mechanical mixture of titanium particles in a magne- sium matrix. These results indicated that the titanium solubility, if such existed, could not be obtained by the usual thermal methods. X RAY DIFFRACTION INVESTIGATION In an effort to detect solubility of titanium in magnesium, samples were investigated using both the Debye-Scherrer and the Focusing Back-Reflection methods. Filings from samples of the thermal analysis billets and from pure magnesium were annealed in argon one hour at 350°C to relieve mechanical strain. Measurements made of the interplanar spacings showed no difference between the Mg-Ti samples and pure magnesium. The interplanar spacings could be measured to within 0.0002A, and the greatest variation found was 0.0004A, in the back-reflection method. The diffraction lines for magnesium were not shifted by the titanium additions indicating that the solid solubility of titanium in magnesium is of a very low order—less than 0.5 pct. From both diffraction methods, a d or interplanar spacing of 0.817A was obtained for the redistilled high purity magnesium. This latter value is not given in the standard X ray diffraction cards for magnesium metal or vacuum distilled magnesium. Theoretical calculations for a close-packed hexagonal space lattice for magnesium indicate that the planes {2134) should give a line which was found. The relative intensity for this reflection at 0.817A is slightly less than that at 0.870k for magnesium. SOLUBILITY OF TITANIUM IN LIQUID MAGNESIUM The Mg-Mn system was examined by Grogan and Haughton6 who were

Jan 1, 1950

By Irwin Roman

Numerous results and formulas have been published for analyzing seismic records, but most of them apply only to large-scale phenomena such as are encountered in studying earthquakes. In a few cases,' formulas have been published for some of the simpler structures. In the present paper, an attempt will be made to analyze several types of structures without using methods more advanced than those of a first course in calculus. In tracing a disturbance through a medium, it is almost always possible to base the analysis on Fermat's Principle of Extreme Time, which states that waves of displacement travel between points in such a manner as to make the time of travel an extremum with respect to all neighboring paths. In the simpler cases, comprising most of those used in optics or geophysical prospecting, this time is a minimum and the principle is often referred to as the Principle of Least Time. Within a homogeneous medium, having a uniform speed of transmission of the disturbance in all directions and throughout the medium, the paths are straight and are refracted at the interfaces in accordance with the Snell law of refraction, which states that the ratio of the sine of the angle, made by the ray with the normal to the interface, to the speed of transmission is the same on both sides of the interface. Thus, in any medium composed of homogeneous sections, this same ratio has a constant value at all points. In particular, if all interfaces are horizontal, it is apparent that the angles of incidence are the angles made by the ray with the vertical direction. Furthermore, the incident ray, the refracted ray and the normal to the interface are all in the same plane at each refraction,

Jan 1, 1934

By Frederick Laist

IT IS obviously impossible to design a copper smelting plant which could be considered, ideal under all conditions. For example, a plant properly designed to smelt the concentrates resulting from the treatment of porphyry ores by flotation would not be the kind of plant that one would design for the treatment of a coarse pyritous copper ore. The smelting of flotation or other fine concentrates is generally accomplished in a reverberatory plant, although occasionally the concentrates are sintered and then smelted in blast furnaces. On the other hand, coarse self-fluxing ores, whether pyritic or semi-pyritic, are generally smelted in a blast-furnace plant. Even this statement is only- approximately true, since the choice will be influenced by many factors; for example, the kind of fuel available (coal, oil or coke), the value of power (electric or steam), the uses to which waste steam may be put (heating, drying, etc.), the cost of refractories (silica and fire brick), the permanence and continuity of the ore supply and the relative first costs of the two types of plant (the reverberatory plant is generally more expensive to construct and to shut down), the contour of the site on which the plant is to be built (rugged, rolling or flat), the intelligence and character of the labor avail-able, and many other factors. From these remarks, it is evident that no copper smelter can be ideal for all conditions of ore and locality, and inasmuch as most of the copper now being pro-duced comes from fine or flotation concentrates and these are generally smelted in reverberatory furnaces, I shall confine my remarks to this type of smelt-ing plant.

Jan 5, 1923

By W. A. White

UNDERCLAY squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay—making it more plastic—or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards. The Coal Div. of the Illinois State Geological Survey has collected samples of underclays from various mines and from cores drilled by coal companies in the state. From these samples natural moisture content, particle size and particle size distribution, and clay mineralogy are determined. Data from samples collected from the underclay below Herrin (No. 6) coal in the Lumaghi Coal Co. mine near Collinsville, Ill., are used in this report to clarify points in the discussion. Data from samples taken from other mines lead to the same conclusions. A generalized geological section for the area is given in Table I. The underclay below coal No. 6 ranges from a few inches to 3 or 4 ft thick. The upper 6 to 18 in. are noncalcareous; the lower part becomes more calcareous with depth. Limestone nodules become larger with depth, almost grading into the limestone below. In areas where the clay is nearly absent the limestone may thicken to take its place; thus they may complement each other in thickness. There are two types of squeeze areas in a mine. In one type up to 3 or 4 ft of underclay lie in what appears to be a depression in the limestone underneath. This is suggested by a rim surrounding the squeeze area where the underclay is thin and the limestone lies within a few inches of the coal. In the second type the underclay of the squeeze area is surrounded by underclay of similar thicknesses which does not squeeze. Test Methods: Natural moisture content, particle size and particle size distribution, and clay mineralogy were determined by the following methods: Natural moisture is the moisture content a clay contains in its natural environment, expressed in percentage of the weight of ovendried clay (110°C or 230°F). To obtain the natural moisture content, given in Table 11, the clay samples were sealed in containers as soon as the samples were taken in the mines. Particle size and particle size distribution were determined by the pipette method,' and the data were plotted as cumulative curves, Fig. 1, on semi-logarithmic paper. Particle size was plotted on the logarithmic scale and percentage on the arithmetic scale. The quartiles (diameters that correspond to frequencies of 25 and 75 pct) and medians (diameters that correspond to the frequency of 50 pct) of the samples were determined from these curves. The clay minerals were identified from the data obtained by differential thermal' and X-ray powder" techniques. The differential thermal analyses were made on the whole samples, whereas the X-ray analyses were made on fractions of less than 2p. Data and Discussion Moisture Content: After the sealed jars had stood for 24 hr, those that contained squeeze samples had perspired, so that droplets of water had accumulated on the insides of the jars. Table II shows the moisture in the clay after it had perspired for 24 hr. (This perspiring was not noted in samples from nonsqueeze areas.) After perspiration one of the squeeze samples still had a higher moisture content than the samples that did not squeeze. Clay Mineralogy: The thermal analysis, Figs. 2 and 3, indicates that the clay minerals are chiefly micaceous in type; the low-temperature endothermal

Jan 1, 1957

APRIL BEGAN with increased disorder in the Ruhr and some blood-shed. The war cloud in the East disappeared, however, with the signifi- cance by the Turks of their intention to return to Lausanne to negotiate a treaty of peace with the Allies. The French occupation of the Ruhr continued during April without there being any spectacular develop-ments. Of course there was surliness on the part of the Germans. In the meanwhile the statesmen on both sides were intimating what they might give and what they might take, sounding the sentiment of their respective populaces. The British Government found that its revenue for the last fiscal year has been greatly in excess of expenses. The surplus was applied to reduction of the debt. A consequence of this development has been a reduction in British taxes for the ensuing year, which has naturally created a much better feeling in Great Britain. On the other hand the unemployment situation in Great Britain caused increasing alarm. At the begin-ning of April about 1,500,000 men were out of work and the thought was developing that this might be not merely a temporary emergency, but a long continuing condition. The uneasiness of the workers themselves began to be exhibited in increasing strikes and threats of strikes. There were important domestic events during April. The six miners who were on trial in Illinois for the Herrin massacre were acquitted, following which the State dropped further prosecutions on the ground that Williamson County is so thoroughly under labor domina-tion that justice could not be had there. The Supreme Court of the United States on Apr. 10 handed down a decision that an act of Congress fixing minimum wages for women in the District of Columbia was unconstitu-tional, being interference with the freedom of contract included within the guarantees of the fifth amendment. Advances of wages became more general during April. The leading event under this head was the action of the United Steel Corporation putting into effect an.11 per cent. increase in the wages of common labor on Apr. 16, by virtue of which the rate per hour was raised from 36 c. to 40 c. This was dictated by competitive conditions, the labor difficulties of the steel industry being due less to a scarcity of men than their disinclination to take jobs in that industry while the building and other industries were paying as high as 60 c. per hour for similar work.

Jan 5, 1923

By G. W. Tuffnell, S. Floreen

Three Fe-18 pet Ni-base ternary alloys cortaining carbon, molybdenum, or cobalt were aged to pgroduce hardening by carbides, Ni3Mo, or ordering, respectively. Each alloy was tested in rotating-beam fatigue tests after hardening to 195 ksi ultim.ate tensile strength. The fatigue properties of three alloys soere essentially identical. The results suggest that tlze fatigae strength of an igron-base alloy should depend primarily upon the tensile strength, and not iipon the hardening mecaanisrn. THE fatigue strengths of many steels have been found to be directly related to their ultimate tensile strengths. For ultimate strengths below 200 ksi, the fatigue endurance limit at 107 to 10' cycles is approximately half the ultimate strength. Essen- tially all of the steels that have been tested, however, have been hardened by carbon. Thus it is not certain whether the relationship between fatigue and ultimate strengths is a general one that applies for other types of hardening in steels, or whether it applies only for the particular method of hardening by carbon. The recent developments of the martensitic precipitation-hardened stainless steels and the marag-ing steels have shown that it is possible to achieve high strengths in iron-base alloys by other hardening mechanisms than that due to carbon. Therefore, it is now possible to compare the fatigue properties of several iron alloys having the same ultimate strengths but hardened by different mechanisms. For the present study a binary Fe-18 pct Ni martensite was selected as a base material. This particular matrix composition has been found to have deformation characteristics very similar to pure iron.' Three ternary alloys were prepared by adding either 0.23 wt pct C, 5 wt pct Mo, or 20 wt pct Co to this base composition. After suitable heat

Jan 1, 1965

By J. L. Lamon, W. Crafts

Study with the electron microscope of the carbides in vanadium-chromium-molybdenum steels after tempering up to 1000 hr at 600 teelsto 1400°F confirmed that alloy carbides are formed at the secondary hardening temperature by decomposition of the plate-like iron carbides. It was also demonstrated that vanadium carbide persists as much smaller particles than do chromium- or molybdenum-bearing carbides. Conditions conducive to the formation of fine vanadium carbides are indicated to be favorable for high temperature strength. IN order to determine the effects of long exposure at high temperatures on vanadium-bearing steels, a survey has been made of their hardness and carbide structure. The behavior of carbides in the tempering of martensite was studied by X ray diffraction and electron microscope examination of electrolytically extracted residues in greater detail than in an earlier investigation.' A group of steels with about 0.25 pct carbon and containing chromium up to 5 pct, molybdenum up to 1 pct, and vanadium up to 1 pct was either quenched or annealed and then tempered for peri- ods of up to 1000 hr at 600° to 1400°F. Their hardness after tempering agreed with the Hollomon and Jaffe2 relation of equivalency of time and temperature, and with the degree of secondary hardening predicted from composition. Further, the appearance of the carbides indicated that the time and temperature equivalency relation was also applicable to the degree of carbide development. The mechanism of the tempering of martensite was demonstrated more clearly than in the earlier study. It was confirmed that carbides develop from martensite as poorly defined plates of the Fe2C type carbide followed by thickening of the plates with a transition to Fe,C. Finally the plate structure deteriorates into a lacy mass from which alloy carbides emerge as chunky particles that grow slowly with further increase of tempering temperature. Vanadium carbide derived from tempered martensite was found in characteristically small particles that tended to grow very slowly. The addition of chromium or molybdenum to a steel with predominant vanadium carbide tended to introduce carbides of a chromium- or molybdenum-bearing type having a somewhat larger particle size. The Cr,C, type carbide particles were larger than those of the V,C, type and somewhat smaller than the carbides in steel containing both Cr,C and M,C. Similar observations were made of the carbides in the pear lite of annealed steels. It appeared that high temperature properties would be benefited by the retention of the fine carbide particles that result from a balance of composition and heat-treatment designed to produce a maximum amount of vanadium carbide. Procedure: The steels used in the investigation were made with a base of Armco iron in a high-frequency furnace at the Union Carbide and Carbon Research Labs., Inc. The steels were deoxidized

Jan 1, 1951

By A. L. Jamieson, H. Rosenthal

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By A. Eilers

In a former paper on Western Smelting Works, I mentioned the great difficulty of obtaining accurate information in regard to the economy of the processes in practice; and to-day, although nearly two years have elapsed since my former paper was written, I am sorry to say that very little improvement has taken place in the keeping of accounts, and in the direction of a more systematic management in the majority of these works. But I am quite certain that by this time even the most sanguine furnace managers must have become convinced, from the experience of the last year, that somewhere in their processes there are enormous losses. Rates for the purchase of ores in 1873 were not as high as they were in former years in certain parts of the country ; labor was no 'higher than formerly; the demand for unparted lead was good throughout the year, with the only exception of the time of the panic, in the fall of 1873; yet there are, of between 40 and 50 works, not more than two or three in Utah and Nevada to-day, that have paid a reasonable interest on the capital invested.

By A. D. Hodges

The process to be described, whatever other merits (or demerits) it may have possessed, certainly proved a financial success under the conditions of the locality where it was introduced and where a refining process had been sought previously in vain. I have ventured to bring it to the notice of the Institute in the hope that it may prove of some interest as a solution of a practical problem, such as is often presented to the metallurgist in the remote mining regions of the West. The method was used first at the Lyon Mill at Dayton, Nevada, and has been adopted at other tailings-mills on the Cornstock. These mills treat two classes of tailings: "sand," or; material which has passed previously through the pans of the ore-mills; and " slimes," or the fine clayey material which, coming from the battery, is too light to settle in the tanks inside of the mills but is

Jan 1, 1886

By K. A. Johnson, F. H. Ellinger, C. C. Land

The Pu-La alloy systenz has been studied by thertnal, tnzcrographic, and X-ray diffraction methods. It is churacterized by a liquid miscibility gap, a maximum solubility of about 20 ut. pct PM in y lanthunum and 19 at. pct PI* in 0 lanthanum, very little soluibility of lanthanum in the plulonium allotropes, and the absence of intermediate phases. THE existence of immiscible liquids in the Pu-La system has been reported by Schonfeld.1 A tentative phase diagram based on the results of thermal-analysis experiments has been constructed by Poole et a1 2 This diagram shows a liquid immiscibility loop with a monotectic at 77 at. pct La and 846°C. 7 lanthanum is shown to dissolve 20 at. pct Pu and to decompose by an inverse peritectic reaction (y La = L , + p La) at about 82 at, pct La and 833°C. The ß lanthanum solvus was not determined, but the thermal work indicated a maximum solubility of 16 at. pct Pu in ß lanthanum. The present investigation has defined the solubility limits of plutonium in y lanthanum and 0 lanthanum, and, with the exception of minor discrepancies, has verified the results of Poole et al. 1) EXPERIMENTAL The electrolytic plutonium melting stocks were better than 99.9 wt pct pure, the main impurities being 90 ppm Fe and 50 ppm W. The lanthanum melting stocks, supplied by Research Chemicals and the Cerium Metals Corp., were about 99 wt pct pure, the main impurity detected by our spectrochemical analysis being 2000 ppm Fe. The components for each alloy button (-5 g) were weighed on an analytical balance and were melted together in a conventional arc furnace. If no significant weight loss occurred during melting, the as-weighed

Jan 1, 1968