Search Documents

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By Edmund Leaver

IT is generally recognized that the .addition of limited small amounts of various lead salts may aid the extracting power of the mill cyanide solution in the dissolution of silver from ores and in some cases may aid in the treatment of gold ores. Excess soluble lead compounds retard the dissolution of precious metals by the usual mill cyanide solution. Another phase of cyanidation is the use of the zinc-lead couple as an aid to better precipitation of gold and silver from solution containing a low percentage of cyanide. The chemistry of the use of lead salts in cyanidation has been dis-cussed by Clennell;1 the addition of lead salts in various cyanide mills is recorded by von Bernewitz;2 and the reasons for the use of lead salts in cyanidation have been explained by Clevenger.3 This paper deals with the adaptation of cyanidation to a different condition, in which the presence of lead minerals in a gold ore that is refractory to direct cyanidation complicates the treatment. If free gold is roasted in the presence of sulfur and lead salts, or if pyritic gold ores containing even a small percentage of lead minerals are roasted to free the gold from the pyrite, lead compounds coat the gold particles enough to make them almost insoluble in the usual mill cyanide solution contain-ing lime for protective alkalinity. Also, the lead compounds remaining in the calcine are slightly soluble in the mill solutions and such dissolved lead may retard the dissolution of the gold by the removal of oxygen or

Jan 1, 1933

By G. Horvay, J. G. Henzel

Nomograms and charts are provided which permit rapid determination of the mold-casting interFace temperature and the speed of solidification when a semiinfinite ingot is cast into a semiinfinite mold. The physical properties of the mold, the frozen metal, and the liquid metal are not assumed to be equal, but they are assumed to be temperature independent. The results are correlated with charts prepared by Paschkis and Hlinka—using Columbia University's Analog Computer—for the freezing of finite ingot slabs when a constant surface temperature is impressed, and with experimental cooling curves obtained by Pellini in sand and iron molds for 7 in.-sq steel castings. x = coordinate directed to right of zero (freezing direction) y = coordinate directed to left of zero (melting direction) e = position of freezing front (in x direction) ? = position of melting front (in y direction) $ = temperature (function of position and time) ? = fixed temperature 2L = width of finite slab Y = a fixed position in the semiinfinite mold, or the width of a finite mold (see Section 7) Properties y = density, lb per cu ft c = specific heat, Btu per lb deg F k = conductivity, Btu per ft hr deg F X = heat of fusion, Btu per lb k = k/Yc = temperature diffusivity, sq ft per hr* b - = = - heat diffusivity, Btu per sq ft deg F Vhr Subscripts 2 = pertaining to the still-liquid metal (case of freezing), or the medium which furnishes the heat (case of melting) 1 = pertaining to solidified metal (case of freezing), or to molten metal (case of melting)* 0 = pertaining to mold (case of freezing), or to the still-solid metal (case of melting) f = pertaining to fusion condition (eg.,?f - fusion temperature) i = pertaining to the location x = 0 (the mold-ingot "interface")

Jan 1, 1960

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book' on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book' on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By H. B. Muller

Single stage autogenous grinding of run-of-mine ore was selected by Broken Hill South Ltd., parent Company of Cobar Mines Pty. Ltd. for the concentrator to treat 60,000 tons per four weekly period of copper and complex copper-lead-zinc sulphide ores from the C.S.A. Mine at Cobar, Australia. Ore is mined by mechanised horizontal cut-and-fill stoping and is prepared for grinding by crushing under- ground in a 60 in. x 48 in. jaw-crusher set at 5 in. closed side setting. The ore is reduced to 80% minus 76 microns in two parallel sections each of one 22 ft. dim. x 7 ft. long autogenous grinding mill, powered by a 1,250 H.P. motor, operating in closed circuit with a single stage 20 in. dim. cyclone. Broken Hill South's original concept of the concentrator required the maximum use of reliable instrumentation, centralised control, and the minimum of manning. To achieve this objective the control room, housing the process recorders, alarms, closed circuit television monitors and all the control equipment, overlooks the grinding and flotation sections, and the whole plant is serviced by a public address system. The grinding units and associated equipment are located in the open and are serviced with the aid of a mobile crane and a mobile hydraulically-operated liner lifting device.

Jan 1, 1970

By R. B. Woodworth

INTRODUCTION IN the sinking of bore holes, there are but two fundamental operations -drilling and hoisting,-which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of petroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the chilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 11, 1915

By George H. Willis

In the second half of the 19th century, bimetallism progressively was replaced by gold standard. After World War I and the 1931-33 depression, gold was mainly reserved for official international transactions and internal use was restricted. Changes since 1971 have shrunk official international use of gold. International payments deficits and surpluses are now financed by Private and official credit, rarely by gold. This historical review covers evolution of: (1) internal and external private use, (2) internal official use, (3) external official use, (4) its role in the International Monetary Fund, and (5) use as unit of account. For this paper I have tried to take a longer perspective than is usually possible, and to look, even if very briefly, at the changing relationship of gold to the monetary system over the last 200 years or so. There are, I believe, some long-term trends, continuing down to the present day. These trends have seen gold replaced by some form of paper assets in one monetary function after another. These past trends may help us to understand where gold stands now, and possibly will throw some light on the future. Because it seems to me that gold in the past has performed various functions related closely or marginally to money, I have divided this rapid historical review into several sections: (1) the internal and external private use of gold, (2) the internal official use of gold, (3) the external official use of gold, (4) gold and the International Monetary Fund, and (5)gold as a unit of account.

Jan 1, 1980

By K. M. Rolls, F. W. Reuter, J. Wulff

The superconducting behavior and microstructural characteristics of a nominal Nb-40 wt pct Ti-0.239 wt pct O alloy were studied as a function of ther mo -mechanical processing treatment. Critical current density us applied transverse magnetic field was obtained for 0.010-in.-diam wires at 4.2°Kin steady fields 14 to 110 kG. Both optical metallogvaphy and transmission electron microscopy were used to delineate the micros tructures of the same wires. It wan found that a 1-hr 500°C precipitation heat treatment after cold drawing to final size led to the highest critical current density. Heat treatment at 600°C also led to a high critical current density, but the precipitate differs in kind and form from that at 500°C. The resistire critical field was also found to be sensitive to precipitation heat treatment since the effective composition of the superconducting phase changes. This is discussed in terms of the oxygen in interstitial solid solution. Two types of high-field superconducting wire are at present used in the construction of high-field superconducting solenoids. These types are solid-solution alloy wire such as Nb-Zr and Nb-Ti and composites of the brittle inter metallic compound Nb3Sn. The latter generally have a high super cur rent-carry ing capacity which is difficult to vary if properly made. The supercur rent- carry ing capacity of the former can be varied drastically and often predictably by suitable thermomechanical processing treatments. In general, the critical current density Jc of the solid-solution type of alloy is increased by cold work and by additions of interstitial elements along with aging heat treatments. The imperfections which result are be-iieved to be responsible for the observed increase in Jc. In 1962 Kneip and coworkers1 found that the critical faurrent density of Nb-Zr alloys could be increased by proper heat treatment preceded and followed by cold work. Betterton and coworkers2 using a Nb-25 at. pct Zr alloy found that small additions of oxygen or carbon enhanced the effect of this heat treatment. They suggested that the interstitials present aided precipitation in the alloy, leading to a filamentary structure with superior properties. If the precipitation heat treatment was omitted, interstitial additions had a negligible effect on Jc. wong3 showed that higher heat-treatment temperatures lowered Jc. Walker and co-workers,4 who studied microstructure (by transmission electron microscopy) as well as superconductivity, found that the Jc anisotropy introduced by cold rolling was itself affected by heat treatment. They were unable to clarify the relation between microstructure and critical current density, although evidence of precipitation was indicated. More recent investigation of Nb-Zr alloys,5,6 besides showing that structural defects and fiber ing due to cold work and precipitation serve to raise Jc, also elucidate important optically observable microstructural changes which occur upon precipitation. In these reports, coarsening of the microstructural features was found to decrease Jc. Vetrano and Boom,7 who studied Ti-20.7 at. pct Nb, found that Jc was increased to a maximum by a 415°C, 3-hr heat treatment following quenching from 800°C and cold working. Heat treatments can also affect the resistive critical field Hr. Final-size heat treatments of Nb-Zr wire can lower Hr drastically if gross phase decomposition occurs5'* or moderately if the effects of cold work are eliminated without changing significantly the composition of the phase of interest.3,5,6,8 The percentage of oxygen which can be added to Nb-Zr alloys to enhance Jc is limited by the difficulty of subsequent cold drawing. Since Nb-Ti and Ta-Ti alloys in contrast can tolerate appreciably higher percentages of oxygen, it was decided to investigate the superconducting behavior of various alloys in these systems. The present paper describes the results of adding oxygen to a nominal 40 wt pct Nb alloy as a function of thermomechanical treatment. I) EXPERIMENTAL PROCEDURE A small alloy ingot was prepared from high-purity niobium, iodide, crystal-bar titanium, and Nb2O5 powder by arc melting on a water-cooled copper hearth in a gettered argon atmosphere. The ingot was turned and remelted fourteen times to insure homogeneity. After final melting and rapid cooling, it was machined round to 0.415 in. diam, jacketed in stainless steel, and cold-swaged to 0.117 in. diam. The jacket was removed and swaging continued to 0.051 in. diam followed by wire drawing in carbide dies to 0.010 in. diam. Although it was intended that about 1500 ppm O (by weight) be added, inert gas fusion analysis indicated a 2390 ppm 0 content, apparently due to additional oxygen pickup in the arc furnace. Even so, the alloy was sufficiently ductile to be cold-worked to greater than 99.9 pct reduction

Jan 1, 1967

By Charles Shamel

I FEAR most of the Institute members are already weary of the perennial controversy about the apex law. I feel that way about it myself now, though I have been guilty of considerable contribution to the discussion in the past. The discussion does not seem to perceptibly influence previously held views and I would not again break into print on the subject but for the urgent invitation of the Chairman of our, Law Committee. This energetic and able member has firmly determined to secure a revision of the mining law and among other things to eliminate the so-called apex provision from the U. S. mining statutes. He is, however, fair about it and has invited me to make "the strongest possible argument in its favor." I am suspicious that he is acting on the psychological principle that it is usually easier to convince an audience against a cause vigorously but unsuccessfully defended than against one wholly mute. Nevertheless, I realize that personally he wishes me no harm, much as he hates the apex law, and so am willing that the Institute have whatever benefit may accrue from my taking up again the unpopular side of the discussion. I say this because the attitude of a large part of our "articulate" membership seems irreconcilably hostile; their minds are made up; favorable consideration is foreclosed; and they become impatient and even sarcastic at any attempt to elucidate a favorable view of the apex law. The exact question for discussion at the present time is not whether on abstract, or any other considerations, the apex law is the best possible rule, but the very different proposition whether, after nearly 50 years of statutory life and much longer as a practically universal miners' custom, it is now just and expedient to repeal the apex law.

Jan 4, 1914

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of' (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.'-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "'12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger's terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

By Hallan N. Marsh

The subject of mud sounds so simple, uninteresting and unimportant that it has failed to receive the attention that it deserves, at least as applied to the drilling of oil wells. As a matter of fact, it is one of the most complicated, technical, important and interesting subjects in connection with rotary drilling. In 1923, R. E. Colloml said "It should be possible to establish certain physical standards for mud fluid," but while considerable work has probably been done on the subject before and since that time, and numerous articles have been written, the progress of general knowledge of the subject and the application of better practices have not kept pace with other developments in rotary drilling, and physical standards cannot be considered as established. Mud is apt to be thought of as an accessible and cheap material, but its cost is likely to be an important factor in the total cost of drilling a well. Some wells "make" most of their own mud out of the formations drilled, but in most cases a great deal of mud-making material has to be supplied from more or less distant sources. Expenditures for mud materials by one California company totaled practically one-quarter million dollars during 1929 and averaged about $13 per rig per drilling day, or about $2000 per well. Under unfavorable conditions, mud cost may reach many times this figure. Parker2 says that in the Hobbs, N. M., field "as much as $75,000 has been spent on one well alone for mud and mud-weighting compounds."' Presumably this is an exceptional case. Unit cost of mud fluid will range from 10 c. per barrel, where suitable material is close at hand, to $1 where crude material is available at moderate price but must be hauled long distances, and on up to as much as $11 per barrel where high gas pressure requires the use of special processed weighting material. The cost of mud pales into insignificance, however, when the results of using improper mud are considered. Blow-outs and lost circulation are obviously the result of inadequate mud. Stuck drill pipe, whether or not twisted off, in many if not most cases probably is caused by cuttings settling out of the mud or the mud itself precipitating. Recent experi-

Jan 1, 1931

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By R. W. Bartlett

The rates of oxidation of tungsten have been determined at temperatures between 1320" and 3170°C and oxygen pressures to 1 amn using a surface -recession measurement technique. Above approximately 2000°C and 10-6 atm the rate is independent of temperature and can be calculated from gas collision theory assuming a constant reaction probability, e, of 0.06. Oxygen molecules react at surface sites where oxygen atoms have previously chemisorbed. This provides a direct pressure dependence at low pressures but at high pressures tungsten oxide molecule s form an adjacent gas boundary layer which lowers the PO2 at the tungsten surface. A correction for this effect using free-convection theory fits the rate data over the entire oxygen-pressure range from 10-8 to 1 atrn as well as data using O2-A mixtures. Below 10-6 atrn and above 2000°C, e decreases with increasing temperature because of desorption of oxygen atoms. Below 2000°C the rate decreases with decreasing temperature at all oxygen pressures following an apparent activation energy of 42 kcal per mole and depending on (Po2)n with n varying between 0.55 and 0.80. MOST of the previous tungsten oxidation studies have employed gravimetric methods and have been limited to temperatures below 1000°C where the weight loss associated with evaporation of tungsten oxides is negligible compared with the weight gain from oxidation.' At higher temperatures, oxygen-consumption rates have been determined from pressure measurements, usually at constant flow rates, by Langmuir,2 Eisinger,3 Becker, Becker, and Brandes,4 and Anderson.5 The sensitivity of this method decreases with increasing pressure and, with the exception of Langmuir's work, these investigations were confined to pressures below 10-6 atm. Above approximately 1300°C, depending on the oxygen pressure, the rate of oxide evaporation is greater than the oxide-formation rate and the recession of the tungsten surface can be measured optically without interference from an oxide layer. This was first done by Perkins and crooks6 who heated tungsten rods in air pressures from 1 to 40 torr at temperatures between 1300" and 3000°C. The present investigation of the oxidation kinetics of tungsten at high temperatures emphasizes oxygen pressures from 10-6 to 1 atm. This is the range of interest for earth atmosphere re-entry applications of tungsten for which little data were previously available. APPARATUS The apparatus is a modification of the type used by Perkins and crooks.' Ground tungsten seal rods, 6 in. long by 0.125 in. diam, were mounted vertically between two water-cooled electrodes, one fixed and the other having free vertical travel. The movable counter-weighted electrode is prevented from undergoing horizontal displacement by three sets of runners mounted at 120-deg intervals. Electrical contact is made by means of a water-cooled mercury pool. A 24-in. vacuum bell jar having a volume of approximately 267 liters was used as the reaction chamber with the sample holder mounted in the middle of the chamber. Power was supplied from an 800-amp dc variable power supply. Temperature readings were made by means of a Latronics automatic two-color recording pyrometer. With this instrument, corrections for emissivity are not necessary provided the spectral emissivi-ties at two closely spaced wavelengths are equal. Supporting measurements were made with a micro-optical pyrometer corrected for emissivity of bare tungsten and window absorptivity. The micro-optical pyrometer was calibrated against a National Bureau of Standards calibrated tungsten lamp and both pyrometers were periodically checked against the melting points of tungsten and molybdenum using the oxidation apparatus. Above 10-6 atm, pressures were measured with an Alphatron gage calibrated against a McCleod gage. At 10-6 atm, a hot-filament ionization gage was employed. A magnified image of the self-illuminated tungsten rod was formed using a 360-mm objective lens mounted outside the bell jar. When the experiment exceeded 1 hr, the image was focused on a ground-glass plate about 10 ft from the tungsten rod at about X8 and the recession of the thickness of this image was monitored with a Gaertner cathe-tometer. When faster rates were encountered, a 35-mm time-lapse cinecamera with a telephoto lens and bellows extension was substituted for the ground-glass plate and cathetometer. Diameter recession rates were determined from the photograph image projected on the screen of an analytical film reader. EXPERIMENTAL PROCEDURE After installing the rod in the apparatus and cleaning it with acetone, the system was evacuated to 5 1 x 10-5 torr. Before oxygen was introduced,

Jan 1, 1964

By R. C. Craze

During the past 20 years. research and development in the study of reservoir behavior have dealt principally with flow of oil through sandstones. Many reservoir studies of sand fields have proved valuable in promoting recovery efficiency. This paper discusses fundamental principles governing oil and gas production from sandstone and limestone alike and presents the results of investigations relating to the application of analytical techniques used for sandstone reservoir studies to the study of limestone reservoir performance. The characteristics of limestone porous systems, porosity-permeability relationships, distribution and occurrence of oil, and characteristics of flow through such systems are discussed. Recognition is made of the similarities or differences which these factors exhibit in limestone and sandstone systems. Comparisons between operating data for typical limestone and sand reservoirs are presented. It is indicated that the distribution and movement of fluids in and through porous limestones follow the same fundamental principles underlying such processes in sandstones. This fundamental similarity may readily be discernible in the performance of many limestone reservoirs. The volumetric balance and unsteady state radial flow equation, the fluid displacement equation, use of electrical analogue devices, and other analytical techniques to study the behavior of limestone fields appear fundamentally applicable, but do require thorough understanding of the properties of the formation, of the fluids, their behavior during flow, and adequate production operating data. Need for more complete coring and comprehensive examination of core properties is stressed. The results of "active oil" studies, and of flow and interference tests are presented. Well spacing, well completion, and efficient rates of production in limestone reservoirs are briefly discussed. INTRODUCTION Limestone and dolomite reservoirs constitute the largest source of supply of crude oil in the world. an estimated 60 per cent of present production coming from carbonate reservoirs. In many large geologic provinces such as Mexico. the Middle East, and more recently Canada, almost all the oil is found in this type of rock. In the United States, all of the major oil-producing areas except California and Pennsylvania contain oil-bearing carbonate formations. The discovery in recent years of large oil reserves in the Silurian, Devonian, and Ordo-vician formations in West Texas, in addition to the large reserves in the Permian, has accentuated the interest of operators, geologists, and engineers in limestone formations and in the many problems associated with understanding the performance of these reservoirs. The rapid increase in discovery of oil in limestone formations and the present-day position of prominence held by these fields in the production and reserve picture in all parts of the world emphasize the horizons opened to the reservoir technologist in the field of geological and production research. Pertinent to an interpretation of the behavior of limestone reservoirs are the methods of analysis which may be utilized and a possession of full knowledge of the many factors which influence the analytical procedures. During the past 20 years a well-developed science of reservoir engineering has been built upon the research of many workers who studied the fundamental nature of oil reservoirs, characteristics of the porous media, properties and behavior of the contained fluids, and the mechanics of flow. Application of these studies to production practice has resulted in greater recoveries and more efficient field operation. The major portion of this evolutionary process has been founded upon studies of sand fields. The applicability of these more thoroughly developed techniques for studying sand fields to the study of the behavior of limestone fields becomes a factor of technical and practical significance. In the light of the technological background available to the reservoir analyst, this paper discusses fundamental principles governing oil and gas production from sandstone and limestone alike and presents the results of investigations relating to the application of analytical techniques used for sandstone studies to the study of limestone reservoir performance. LIMESTONE RESERVOIR CHARACTERISTICS The characteristics of limestone and sandstone reservoirs are similar in many respects and they both may occur under similar structural conditions. Fundamentally, the distribution and movement of fluids in and through the porous limestone media follow the same basic principles which dictate such processes in sandstones. Herein lies a fundamental similarity, which may readily be discernible in the performance of many limestone reservoirs. In some limestone fields, as in many sand fields, widely varying formation properties and distribution may reveal themselves in deviations in the performance of the reservoir, in the behavior of wells, and in fluid flow through the rock, and make difficult the delineation of reservoir behavior. Only by reservoir studies, core analyses, and coordinated laboratory and field experimentation can the effects of the many influencing factors upon the nature of limestone production be determined. FORMATION CHARACTERISTICS The chief difference between limestone and sandstone, aside from their chemical compositions, is the difference in the geometry and origin of the porous systems in the two kinds of rock. In sandstone the porous system results entirely from the openings among individual sand grains which occur during deposition. The geometry of the openings between the sand

Jan 1, 1950

By Peter Tegart

The discovery of gold in the Toodoggone River area is credited to Charles McClair who mined placer deposits in 1925, reportedly valued at $17,500. After he and his partner went missing in 1927, efforts to relocate their workings resulted in the formation of Two Brothers Valley Gold Mines Ltd. in 1933, in which the legendary Grant McConachie (first president of CP Air) played an active role. This was the age when the prospector first utilized the airplane to reconnoitre remote areas. What greeted the observer from the air was an area rich in orange and yellow colours characteristic of gossans formed by the oxidation of sulphides. However, Samuel Black, a Hudson Bay Company fur trader, had also noted in his diary as early as 1824, the unusual and many gossanous colours in the headwaters of the Finlay River. These gossans, coupled with white limestone bluffs and the presence of placer gold, attracted the first reconnaissance of the area by Cominco in 1929. Cominco was ever active in remote areas at this time. They staked and worked several base-metal showings hosted by limestone at the margins of intrusive stocks. These early workers also obtained erratic high gold assays from chalcedony float samples found in creeks draining into the Toodoggone River. However, because the samples gave inconsistent assays, no concerted effort was made to locate their source. Except for the occasional horse-supported prospecting party of the late 1940s and early 1950s, the area did not receive much attention until 1968. Work until this time focused on the base metal lead-zinc showings which contained attractive silver credits. Gold was not an attraction because of the set price established by the US government. The late 1960s saw the northward expansion of porphyry copper exploration into the Toodoggone. A program of gossan soil sampling (gossans which had attracted the early workers) was carried out by Kennco Explorations (Western) Ltd. in 1966-1967. They analysed for base metals in the field, using a cold extraction method. The Kemess copper- gold prospect was staked as a result of anomalous copper values from this early geochemical program. In 1968, Kennco continued the program of silt traversing and field geochemical testing. The samples were further subjected to multielement analysis consisting of copper, molybdenum, lead, zinc, cobalt, nickel, and silver at Kennco's North Vancouver laboratory. Several anomalous creeks, high in combinations of copper, molybdenum, and silver, were outlined. Some initial soil grids were also established. The fall of 1969 saw the return of Kennco prospector Gordon Davies and geologist Bob Stevenson to check out a well-defined molybdenum, scattered copper and silver anomaly in soils from a grid on the Chappelle claims. The subsequent analysis of several selected quartz felsenmeer floats yielded one assay which ran in the order of 0.25 kg/t (8 oz per st) gold and 2.2 kg/t (70 oz per st) silver. Subsequent trenching on the Chappelle claims exposed the source of float in a 4- m (134) wide vein of high grade gold-silver mineralization. These results led quickly to the realization that the district had precious metal potential. Subsequent exploration in the period 1969-1974 by Kennco resulted in the discovery of most of the gold and silver occurrences on the Chappelle and Lawyers properties. Several other gold and silver occurrences were found in this district by Cordilleran, Cominco, and Sumitomo, working the district during this period. Conwest optioned the Chappelle in 1973 and explored underground by adit entry as part of a one-year program. In 1974, Du Pont of Canada Exploration Ltd. optioned the Chappelle claims and in March 1980, using reserves developed on the A vein, placed the Baker mine into production at a rate of 90.7 Vd (100 stpd). The Amethyst zone on the Lawyers property, 8 km (5 miles) north of Chappelle, was found in 1973 by Kennco using continued, persistent followup prospecting of silver silt geochemical anomalies. A silt anomaly in the order of 3.4 ppm silver occurred in a stream flowing 300 m (984 ft)

Jan 1, 1985

By B. S. Gottfried

A generalized mathematical model is presented, which describes the thermal recovery of oil in linear systems with convective external heat loss. Three-phase fluid flow, conduction-convection heat transfer, chemical reaction between oxygen and oil and aqueous phase change are included, making the model applicable to a variety of thermal recovery processes. The complexity of the model requires that numerical solutions be obtained with a digital computer. The numerical approximations of the partial differential equations are presented and the algorithm is discussed in detail. The analysis is applied to the detailed simulation of a forward-combustion laboratory tube experiment. The results of the simulation exhibit with reasonable accuracy all of the principal thermal and bydrodynamic characteristics observed in the laboratory (i.e., the propagation of a combustion zone, a steam plateau, and oil and water banks). Numerical variations in the parameters appearing in the external heat-loss term, the aqueous phase-change term, and the Arrhenius combustion term are examined, and their effects on the predicted temperature profiles, oil and water production histories, and the air-oil ratio are presented. In spite of an oversimplification in the chemical reaction mechanism and the considerable computer time required to obtain solutions, the model represents a major advance in the ability to simulate the phenomena observed in thermal recovery experiments. INTRODUCTION Thermal oil recovery refers to a class of recovery processes where heat is supplied to a reservoir to provide the necessary expulsive energy. This thermal energy can be supplied externally as steam or hot water, or it can be generated in situ by forward or reverse combustion. In either case, however, thermal recovery processes are charac- terized by the simultaneous flow of two or three fluid phases in a variable - temperature field, accompanied by possible chemical reaction or phase-change effects.2-5, 7- 10, 14,16-18,20-22 Although a physical understanding of the thermal recovery processes is far from complete, it is possible to construct mathematical models which describe approximately all of the principal physical and chemical phenomena. However, attempts to solve such models, even with high-speed computers, involve formidable mathematical difficulties. Consequently, theoretical solutions have been obtained only for idealized cases in which important physical phenomena are neglected. For example, consider the process of forward in situ combustion. All such theories which have been developed consider only certain aspects of the process, such as heat transfer, 2-4,8,9,l6,l8 heat transfer with phase change,10 heat transfer with chemical reaction,7 or the hydrodynamics of three-phase flow.21 A general theory including all of the above phenomena has not been developed to date. This paper presents a unified theory of thermal recovery processes in linear systems. A mathematical model is developed which explicitly includes conduction-convection heat transfer with convective external heat loss, chemical reaction between air and oil, aqueous phase change, and the hydrodynamics of three-phase flow. A system of equations is developed which can be solved numerically on a high-speed digital computer, resulting in predicted temperature, pressure, and saturation histories in space and time. The model allows a more detailed simulation of thermal recovery tube experiments than had previously been possible. THEORETICAL DEVELOPMENT Consider the linear flow of gas, water and oil in a homogeneous porous medium. Assume that the oil will react with gaseous oxygen, and that mass is transferred between the water and gas phase by evaporation or condensation. In the absence of hydrocarbon phase change, intraphase diffusion,

Jan 1, 1966

By P. J. Spencer, J. N. Pratt

The vapor pressure of manganese over liquid Mn-Sn alloys has been determined by a high-temperature torsion-effusion technique. Alloys containing from 8 to 100 at. pct Mn were investigated in the temperature range jrom 1280" to 1580" and the measured pressure values were used to calculate the partial and integral thermodynamic properties of the liquid alloys. The activities show small negative departures from ideality while the integral heats and excess entropies of mixing are asymmetric inform, changing from positive to negative with increasing manganese content. The possible contribution of various factors to the observed thermodynamic properties is discussed. COMPARATIVELY few thermodynamic data are available for manganese alloy systems.' Therefore, as part of a continuing program of studies of the thermodynamic properties of transition metal alloys, measurements have been made on various binary alloys involving this element. In recent publications,2~3 investigations of liquid Mn-Cu alloys and of the Mn-Au system in both solid and liquid states have been reported. For the first-mentioned system the work suggested that magnetic interactions may be responsible for the observed form of the thermodynamic properties, while in the second the influence of the electrochemical factor appears to be dominant. The present paper describes a similar study of liquid Mn-Sn alloys. Again the thermodynamic properties have been obtained from vapor pressure measurements made by use of a high-temperature torsion-effusion technique.4 A detailed description of the apparatus and of the experimental procedures used in alloy preparation and pressure measurement may be found elsewhere.2'4 EXPERIMENTAL RESULTS Sixteen alloys, ranging in composition from 8 to 100 at. pct Mn, were prepared from spectroscopically standardized manganese of 99.99 pct purity and tin of 99.999 pct purity, both supplied by Johnson-Matthey and Co., Ltd. One-gram samples of the alloys were obtained by carefully weighing appropriate amounts of the pure components into an effusion cell; this was then suspended in the apparatus and the metals melted together in situ by heating under vacuum to approximately 1550°K. After allowing sufficient time for a homogeneous liquid alloy to be formed, vapor pressure measurements were commenced. These were determined as rapidly as possible at a series of steady temperatures within the range of interest. The duration of experimental runs on individual samples was kept sufficiently short to ensure insignificant varia- tion of alloy composition during investigation. After completing pressure measurements, the alloys were rapidly cooled and their compositions checked by weighing or chemical analysis. All experiments were conducted using effusion cells machined entirely from boron nitride. Measurements were made using a variety of cells with orifice areas ranging from 0.0032 to 0.0075 sq cm and lengths of the order of 0.04 cm; the usual effusion correction factors for orifice geometry and molecular distribution were calculated using Freeman and Searcy's equation5 and had values between 0.6 and 0.75 for the orifices employed here. The vapor pressures of manganese over the alloys were measured at approximately 20°K intervals in the temperature range 1280" to 1580°K. In view of the close approximation of the measured pressures to Clausius-Clapeyron behavior in the experimental temperature range, the data for each alloy have been expressed by equations of the form: logp(atm) =-A/T + B A least-squares computer treatment was applied to the vapor pressure values in order to obtain the coefficients A and B with their associated error. The resulting equations are listed in Table I, together with the equation for pure solid manganese obtained from a previous study.4 To minimize the effect of possible apparatus calibration errors, the activities and partial free energies of manganese in the alloys were calculated by initial reference to the latter equation, obtained from identical torsion-effusion measurements. The immediately resulting thermodynamic quantities, based on a solid manganese reference state, were then converted to refer to the more appropriate supercooled pure liquid manganese standard; tabulated values of the free energies of solid and liquid manganese from Hultgren et al.' were used for this purpose. Partial entropies of solution of manganese were calculated from the temperature coefficients of the free energies and partial heats from the Gibbs-Helmholtz relationship.

Jan 1, 1969

By G. K. Burgess

THE question of the allotropy of iron, in spite of a vast amount of experimental work and perhaps an even greater amount of theorizing, is not yet settled. That there is a definite transformation in iron near 900,° the A3 point, is generally recognized, as well as the fact that the temperature of this transformation is lowered by the addition of carbon and metallic elements. On heating, the transformation Ac3 is always found at a higher temperature than the transformation on cooling, Ar3. Whether the A3 transformation is sharp like the melting point of a pure substance, or extends over a considerable range of temperatures, embracing perhaps as a lower limit the A2 change, appears to be still an open question for pure iron. The nature and identity of the A2 transformation, it would appear from recent publications, has not yet been satisfactorily settled. In the present paper a critical, historical summary is given of the experimental investigations of the location of A2 and A.3 in pure iron, together with brief mention of some of the theoretical aspects of the subject, and an account is given of a series ?of experiments carried out with several samples of very pure iron which were studied by two methods of thermal analysis in the range from 5000 C. to 1,000° C., and which it is believed furnish a contribution of considerable interest as to the location and nature of the A3 and A2 transformations. Great attention has been given to the details of experimental manipulation and to the preparation of the samples, as it was soon found that some of the discrepancies noted in the work of many experimenters may be traced largely to lack of precautions which we have found essential. For example, to anticipate somewhat, it is necessary to provide a suitable practically gas-free furnace, the heating and cooling of which may be regulated to a nicety. To render a minimum the deforming effects on the cooling and heating curves of the poor conduction of the sample, it must be of a form and mass to pass on its heat rapidly and completely to the thermocouple; and finally the sample itself must be freed from gases which, if present, further mask the definiteness of the heating and cooling curves. We, have also varied within wide limits the several factors which may influence the determination of the exact location and shape of the transformation ranges, especially the mass and preparation of sample, rate of heating and cooling, design of furnace; and finally, as nearly as it is experimentally possible, we have worked with a substance approaching pure iron, free from occluded gases and other impurities, and contained within a vacuum.

Jan 10, 1913

By A. J. Jacobs, G. Katz

MANY of the studies of intermetallic compounds containing uranium were performed during the early 1940's under the aegis of the Manhattan Project. Subsequently, much of this work was declassified and published after 1949. In some instances this early work, completed with relatively impure materials, represents the only source of X-ray diffraction powder data available in the literature. In the case of the intermetallic compound U,Fe some discrepancies in the powder pattern exist in the literature. Since this compound has been prepared in this laboratory, it is believed that the publication of the indexed powder pattern would help clarify the conflict in the literature. In studies of the U-Fe system, Gordon and Kauf-mannl and Grogan and Clews2 independently reported the intermetallic compound U,Fe in 1950. The crystal structure was described by Baenziger, Rundle, Snow, and Wilson3 in 1950. It is isostructural with U,Mn, U,Ni, and U,Co and crystallizes in a body-centered tetragonal lattice. The lattice constants determined by Baenziger et al. are: giving an X-ray density = 17.7 g cm-3 for 4 mol per unit cell. The compound used in this study was prepared by melting a stoichiometric mixture of the constituent metals in an argon-arc furnace using a nonconsum-mable tungsten electrode. Before the argon of 99.98 pct purity was introduced into the furnace, it was passed through CaC1, to remove water vapor and afterwards through a stainless steel tube containing calcium turnings heated at 600°C for the removal of nitrogen and oxygen. The purity of the uranium used was better than 99.9 pct and that of the iron was 99.97 pct. Before and during melting a zirconium getter was used to further purify the argon atmos-

Jan 1, 1962