Search Documents

By Robert E. Green, P. W. Kingman

Application of a constant geometry compression test to single crystals of aluminum of selected diameters from 1/4 to 1/64 in. showed the presence of a diameter-dependmt size effect. The most pronounced effects were found in those crystals oriented for single slip, while for specimens possessing orientations in the comers of the standard stereographic triangle virtually no size effect was exhibited. The yield stress of the crystals oriented for single slip was found to increase with decrease in specimen diameter, while the strain-hardening rate was found to be lower for the smaller specimens. The experimental results are in general agreement with those of other investigators obtained from lensile tests on copper and aluminum crystals. THE earliest systematic investigation of a possible size effect on the plasticity of metals was that of no,' who in 1926 performed tensile tests on cylindrical aluminum single crystals with diameters of 3 to 8 mm. Ono concluded that the gross stress-strain curve did not show a diameter dependence, but that the resistance to slip for strains of 0.1 pet and less appeared higher for 3-mm-diam crystals than for larger sizes. Later studies of aluminum by Maddin et al2 tentatively concluded that a size effect exists, but the conclusions were again open to question because of inconsistencies in the experimental data. Wu and Smoluchowski3 had previously shown that the slip system activated in a single-crystal sheet specimen of aluminum is a function of the specimen cross section in the slip direction, but no stress-strain data were obtained. Subsequently Fleischer and Chalmers4 studied the effect of the length of the slip direction of the primary-slip system on the stress-strain curve by testing aluminum crystals with geometrically dissimilar cross sections. In the course of this investigation a size effect was indicated in rather large crystals; however, the number of these tests was small. Other investigators have indicated that a size effect in aluminum is appreciable only for diameters of 0.5 mm or less.5, 6 Size-effect studies have also been carried out on copper crystals, the most detailed being that of Suzuki et a1.7 who performed tensile tests on specimens of many diameters ranging from 2 to 0.12 mm. Suzuki found a strong size dependence in the easy-glide region, both the extent of the easy glide and the hardening rate in easy glide were size-dependent, and the size effect was found to be orientation-dependent. Suzuki's results are in agreement with the less extensive observations of Pater-sonB and those of Garstone et al.9 A size effect was found by Rebstock using tubular copper crystals.'0 Size effects have also been noted in a brass,6, 11 in cadmium,12'19 and in hexagonal crystals.14 All the previously cited works have been entirely concerned with the variation of specimen cross section. The effects of specimen length and the change of specimen geometry which results from using progressively thinner specimens while maintaining the same specimen length have been largely ignored. A theoretical discussion of the effects of specimen length and geometry has been given by Hauser and Jackson,15 who predict a grip effect on easy glide as a function of specimen geometry provided that the specimen dimensions are large compared with the spacing between the slip bands, and by Fleischer and Chalmers,18 whose analysis of grip effects resulting from lattice rotation predicts an increase in easy glide with an increase in specimen length. A study of size and geometry effects in aluminum crystals by Kitajima and shimba17 indicated increasing amounts of easy glide in specimens of increasing length and identical cross section, and nearly identical stress-strain curves for specimens of different sizes having constant length-to-diameter ratios. Since the present study is primarily concerned with diameter dependence, the following factors were taken into account: specimen material, specimen geometry, testing method, range of sizes to be tested, and possible influence of surface and volume effects. Aluminum was chosen because of the present lack of conclusive results and the seeming possibility of size effects at relatively large diameters, the

Jan 1, 1964

By T. B. Counselman

C. G. McLachlan—In the foregoing paper the author has presented a very neat method for calculating the solution recovery for a countercurrent flowsheet. He has, however, based his calculations, as he states, on the assumption that "the concentration of dissolved value must be exactly the same in the overflow and underflow of any thickener." This assumption, which is usually made regardless of the type of calculation used, is "not strictly correct because diffusion of the dissolved gold in the solution associated with the solids as it progresses through the countercurrent system is far from being instantaneous, with the result that on a ton for ton basis, the assay of the solution in the thickener underflow is higher than in the corresponding thickener overflow. An agitator introduced into the flowsheet between thickeners will reduce, but not entirely eliminate, this difference. In practice we have found that the best way to take care of this condition— in addition to the use of one or more intermediate agitators—is to circulate 20 pct or 25 pct more solution than called for by the cheoretical calculation. This presents no difficulty provided that adequate thickener capacity is provided in the original design of the countercurrent circuit.

Jan 1, 1951

By T. B. Counselman

C. G. McLachlan—In the foregoing paper the author has presented a very neat method for calculating the solution recovery for a countercurrent flowsheet. He has, however, based his calculations, as he states, on the assumption that "the concentration of dissolved value must be exactly the same in the overflow and underflow of any thickener." This assumption, which is usually made regardless of the type of calculation used, is "not strictly correct because diffusion of the dissolved gold in the solution associated with the solids as it progresses through the countercurrent system is far from being instantaneous, with the result that on a ton for ton basis, the assay of the solution in the thickener underflow is higher than in the corresponding thickener overflow. An agitator introduced into the flowsheet between thickeners will reduce, but not entirely eliminate, this difference. In practice we have found that the best way to take care of this condition— in addition to the use of one or more intermediate agitators—is to circulate 20 pct or 25 pct more solution than called for by the cheoretical calculation. This presents no difficulty provided that adequate thickener capacity is provided in the original design of the countercurrent circuit.

Jan 1, 1951

By B. C. Allen

Grain-boundary gvoocing was studied irz chronziu?n. molybdenum, tungsten, and the solid-solution alloys, Cr-35Re. Mo-33Re, and W-25Re at 0.6 to 0.9 of the absolute liquidus temperature under an inevt atmosphere , foveign nzetal zlapor, and liquid metal. The controlling mechanism of matter transport was deduced frolr groove size and shape. kinetics of growth, and cotnparisoz with theoretical relatiotzships derived by Mullins. Grooves in chowzizon formed prittzarily by volume diffusion tkrongk kelium or argon at 1 atm pressure and by e1)apovation-condensatiotz in a static vacuum. Groozles in the other nzetals and alloys forrned priniarily by sirface diffusion, the coefficients of which were calculated. Carbon was found to decrease the acti7:ation energy for surface diffusion on molybdenun. Sitrface diffusizities weve sinzilav for iWo-0.0ZC and Mo-33Re. The presence of about 1 -?nm pressure of silver or tin vapor did not affect the neckanis)n of grooz;e formation. In liquid titz or silz:er, pain bolindary gvooves formed by zolume diffusion in the liquid. BASED on theories of ullins," the mechanisms of grain-boundary grooving have been determined for low-melting metals such as copper in an inert atmospheres or in liquid lead.4 The purpose of this investigation was to study grain-boundary grooving in the refractory Group VI-A metals, chromium, molybdenum, and tungsten, and the bcc solid-solution alloys, r-35e, 0-33e,= and -25e,' at 0.6 to 0.9 of included to see whether Mullins' theories were applicable to them as well. EXPERIMENTAL WORK The materials chromium, molybdenum, tungsten, Cr-35Re, Mo-33Re, and W-25Re were in the form of 0.050-cm-thick sheet assaying 99.98 pct or better. The nominal carbon level was generally 30 ppm. The oxygen + nitrogen + hydrogen content was -50 ppm. Mo-33Re and W-25Re were prepared by powder-metallurgy methods and supplied by Chase Brass and Copper Co. The remaining materials were arc-cast. Chromium and Cr-35Re were prepared at Battelle by arc melting, extruding, swaging, and rolling. Mo-0.003C was supplied by Climax Molybdenum Co., and Mo-0.02C and tungsten by Universal Cyclops Corp. As a source of liquid metals, tin and silver granules assaying 99.98 pct were used. Spectrographic analyses indicated the presence of -100 ppm each of iron and silicon. Vacuum melting reduced the combined gas content to c5 ppm (2.60,, 0.9N2, 0.4H2 in tin and l.602, 0.7N2, and c0.04H2 in silver). Specimens were prepared for grain-boundary grooving. Coupons 0.5 by 1.5 cm with a small hole in one end, or substrates 1.5 by 1.5 cm, were cut from sheet. The specimens were annealed in containers of the same material to provide a vapor-solid equilibrium as well as to protect them from gaseous impurities. Outgassing was done at 2 x 10"5 mm for 15 to 30 min at 1150°C for chromium and Cr-35Re, 1750°C for molybdenum and Mo-33Re, and 2600°C for tungsten and W-25Re. Then recrystallization to a stable grain size of about 0.5 mm was accomplished by annealing at least 1 hr at 1600°C for chromium, 1800°C for Cr-35Re, 2350°C for molybdenum, and 2300°C for Mo-33Re in a rhenium-element resistance furnace under 1 atm of static argon or helium. The atmosphere was gettered by tantalum radiation shielding. Tungsten and

Jan 1, 1967

By George S. Ansell, John B. Hudson, Stephen A. Koffler

The permeability of hydrogen through the a phase of palladium has been measured by a low pressure permeation technique under conditions such that bulk diffusion was the rate-controlling process. The observed permeability is described by the equation: J = 1.80 x 1O-3 P½exp(-3745)/RT) cc(stp)/sec/cm2/en over a range of hydrogen pressure, P, from 2.9 x 10-5 m Hg to 5.0 x 10-3 cm Hg, and over a temperature range, T, from 300" to 709°K. The fact that the permeability shows a square root dependence on pressure and a reciprocal dependence on thickness was taken as evidence that bulk diffusion, rather than surface reactions, was the rate-controlling process. The permeability data were used in conjunction with the solubility data of Salmon et al., to determine the diffusivity of hydrogen through palludium as: D = 4.94 x 10-3 exp(-5745/RT) cm2/sec There was no influence of sub structural defects observed over the temperature range employed. From the permeability data obtained, coupled with grain size measurements, it was concluded that the ratio of grain boundary diffusivity to bulk diffusivity was less than 105 over the range of temperature investigated. THE diffusive mass transport of hydrogen in the a phase of palladium has been studied previously by numerous investigators.' In spite of the large amount of attention this system has received, there is not good agreement between the results obtained in different investigations.' This is due in part to the fact that the mass transport was surface-limited during some of these studies, rather than being diffusion-controlled3-5 The reason for the disagreement in other cases is not clear. These studies made use of such techniques as rate of absorption from solutions6 and gases,' electrochemical potential,8 time lag,' and permeation10,11 to determine the mass transport behavior. Of these, the gas permeability technique is the only method which allows an easy test to determine if diffusion is the rate-controlling mechanism, thus eliminating the uncertainty regarding the limiting transport processes inherent in the other techniques. The two most recent permeability studies are those of Toda10 and Davis." Toda determined the permeability of hydrogen in the a phase of palladium over the temperature range from 170" to 290°C, and over the pressure range from 36 to 630 mm Hg utilizing a steady-state gas-permeability technique. Toda's result was: J = 1.41 x 10-3 P½ exp(-3220/RT) where J = specific permeability in cc(stp)/sec/cm2/cm, P½ = square root of the inlet pressure in (cm Hg)½, R = Universal gas constant, and T = temperature in deg Kelvin. Davis11 also employed a steady-state gas-permeability technique over the temperature range from 200" to 700°C and over the pressure range from 0.02 to 760 mm Hg. His result for the permeability of hydrogen in the a phase of palladium was: J = 3.15 x 10-3 P½ exp(-A440/RT) In the range of overlapping temperature for these two investigations, the values of the specific permeability calculated from the above two equations differ by a factor of about 1.8. In the present investigation, the permeation of hydrogen in the a phase of palladium was determined over a wide temperature range, 27" to 436oC, and over the pressure range from 2.9 x 10-5 to 5.0 x 10-3 cm Hg. This temperature range overlaps that of the previous investigations of Toda and Davis, but also covers the lower temperature range which has never before been investigated. The lower pressure range used here avoided the interaction between the dissolved hydrogen atoms observed at higher hydrogen concentrations.' MATERIALS The as-received palladium specimens were cold rolled from a casting and were supplied as 5.08 cm discs of 0.508 and 0.762 mm thickness. According to J. Bishop and Company specifications, the composition of the discs was 99.95 pct Pd, the balance being Cu, Ag, Au, and Ir. In order to obtain samples of varying grain size, the as-received discs were then heat treated. Sample 1 was treated for eight minutes in a nitrogen atmosphere at 810°C and then air-cooled. Sample D was heated first to 550°C in helium. The helium atmosphere was then immediately replaced by hydrogen and the temperature was slowly raised to 1220°C and held for 22 hr. The sample was then cooled to 550°C where the hydrogen was replaced by helium and the disc was further furnace-cooled to room temperature. Sample H was given the same heat treatment, only with hydrogen substituted for helium below 550°C. The reason that hydrogen was not used throughout the entire annealing cycle for samples D and H was to prevent the distortion encountered by low-temperature cycling in hydrogen observed by Darling." After these heat treatments were completed, the

Jan 1, 1970

By E. R. Buchanan, R. E. Reed-Hill, F. W. Caldwell

Poly crystalline zirconium tensile specimens containing a sizable fraction of grains unfavorably oriented for slip were deformed at 77°K to strains as high as 9 pct. The contributions of the various twinning modes to the observed strain were deter~nlned quantitatively using measured twin volume fractions and Schrnid orientation factors. The results indicate that at very small strains twinning can account for almost all of the observed strain. At higher strains slip becomes the dominant means of deformation. The most significant form of twinning was {1121}. PLASTIC deformation in polycrystalline aggregates is poorly understood even today. This is primarily because slip cannot be easily observed or studied in the interior of a metal. On the other hand, twinning can be discerned inside a specimen after deformation. Twinning studies can therefore often yield quantitative information about polycrystalline deformation not otherwise obtainable. This investigation uses the above aspect of twinning in determining the contributions of twinning to the strain during tensile deformation at a cryogenic temperature (77°K). Polycrystalline zirconium was used as the object of study. There are several reasons why this information should be of value. In contrast to many metals, both the strength and ductility of zirconium increase with a corresponding decrease in temperature. This may be related to the fact that twinning becomes more profuse and complex with decreasing temperature. Secondly, it has been discovered that certain room-temperature properties of zirconium can be greatly improved by about 1 pct prestrain at 77°K. These include an increase in tensile elongation in critical directions by over 50 pctl and a large mechanical hysteresis effect.2 Both effects are believed to be related to twins formed by prestraining: plastic twin-boundary movements accounting for the increased ductility, and anelastic twin-boundary movements for the internal friction. Thirdly, hexagonal metals which twin primarily on only the (1012) mode (such as beryllium, zinc, and magnesium), unlike zirconium, are very limited in ductility at cryogenic temperatures. Therefore, the significance of the various types of twinning in zirconium at cryogenic temperatures is of more than academic interest. Three twinning mechanism-s have beenobserved in quantity at WOK, {1012), {1121), and {1122). Each must be considered as a unique deformation mechanism because of their markedly different twinning shears and basically different angles between twinning and basal planes, as shown in Table I. It is therefore necessary to separately consider the role of each of these twins during plastic deformation at 77°K. Fortunately, each twin possesses unique morphological features which makes its identification possible on a properly prepared metallographic section. The use of the polarized microscope3 can also greatly aid in identification of the various forms of twins. EXPERIMENTAL PROCEDURE Arc-melted sponge zirconium plate, previously describedY4 was machined into 1/8 by 1 1/4 in. threaded-end, round tensile test specimens. These specimens were deformed to the desired strains in a liquid-nitrogen cryostat mounted in an Instron testing machine. The tensile axis was the transverse plate direction. This specimen direction resulted in large numbers of grains in orientations unfavorable for deformation by prism or basal slip. Deformed specimens were sectioned, mounted in epoxy cold-mount resin, ground on metallographic papers, electropolished, and anodized to provide surfaces sensitive to polarized light. Standard quantitative metallographic procedures5

Jan 1, 1965

By M. Garfinkle, W. D. Klopp, W. R. Witzke

The tensile properties of binary W-Re alloys containing up to 33 at. pct Re were determined at temperatures from 78" to 3630°F. Elongations as high as 260 pct were observed in electron-beam-melted tungsten containing 23 at. pct Re when tensile-tested at 3630°F after a 1-hr anneal at 3090°F. All alloys tested under these conditions with rhenium contents between 20 and 28 at. pct exhibited elongations of at least 200 pct. These alloys also showed enhanced grain growth rates. The values of strain-rate sensitivity ranged between 0.2 and 0.3 for the alloys exhibiting high elongations. Houlezler, for swaged alloys tested just above the re-crystallization temperature, strain-rate sensitivities as high as 0.8 were observed. The high-temperature strengths of the high-rhenium-content alloys were also less than those of alloys with intermediate rhenium contents. ALLOYING with rhenium has two distinct effects on the mechanical properties of tungsten. One effect occurs in dilute solid solutions and is most clearly seen in the lowering of the hardness and of the ductile-brittle transition temperature at about 5 at. pct Re.1-3 The second effect occurs in the concentrated solid solution at about 25 at. pct Re, and is characterized by twinning and a larger decrease in the ductile-brittle transition temperature. An aspect of the high-rhenium-content alloy which has received little attention is the higher-than-usual tensile ductility at 3500°F.3 Anomalous high ductility has been observed in several other alloy systems. usually associated with a phase transformation or a solid-solubility limit.4'5 The phenomenon is now commonly termed superplasticity. High-strain-rate sensitivities6 and grain boundary sliding7 have been reported for materials that undergo superplastic deformation. Also, it has been found that superplastic materials usually have a very fine grain structure (less than 10 pm).8 and it has been proposedg that such a structure alone is sufficient for superplasticity. The purpose of the present study was to further characterize the high-temperature tensile properties of W-Re alloys to determine the conditions under which they might be superplastic. Tensile and selected strain-rate sensitivity tests were conducted on alloys containing 0 to 33.3 at. pct Re at temperatures from 78" to 3630°F. Grain-growth rates were also determined on most alloys at 3630°F. Fig. 1 indicates the compositions evaluated and their locations relative to the solvus line in the tungsten-rich end of the W-Re phase diagram. Twelve binary W-Re alloys containing up to 33.3 at pct Re were double electron-beam-melted and subsequently fabricated to 0.3-in. rod by extrusion and swaging. The starting materials were commercial powders of tungsten and rhenium with impurity levels as listed in Table I. The various blended W-Re compositions were hydrostatically pressed at 70 ksi. The pressed bars were drip-melted into 1.5-in.-diam ingots and then remelted into 2-in.-diam ingots at a chamber pressure of 10~5 torr. The ingots were canned in molybdenum and extruded to round bar at a reduction ratio of 6:l. The alloy extrusions were swaged to about an 80 pct reduction at 2100" to 2900°F. Buttonhead tensile specimens with a reduced section diameter of 0.16 in. and a gage length of 1.0 in. were centerless-ground from the swaged bars

Jan 1, 1970

By Walter R. Crane

PAGE I. Apparatus and Methods.......... 406 1. The Magnetic Circuit...........406 2. Apparatus Employed in the Traction-Method...... 406 a. The Coils............409 b. The Pole-Pieces..........409 3. Methods of Testing Fields Produced by Different Pole.Pices.. ..409 c. Testing with a Search.Coil........410 d. Testing with Iron-Filings and Glass Tube.. .. .410 4. General Forma of Pole-Pieces.........411 e. Flat Poles............411 f. Conical Poles........... 411 g. Spherical Poles...........411 h. Chisel-Edged (Chamfered) Poles.......412 II. Magnetic Fields...........412 5. Methods of Testinq for Magnetic Permeability...... 421 i. The Rod-Method..........423 j. Method Employed in These Experiments......424 k. Difference in the Results of the Two Methods..... 425 l. The Traction-Method.........427 m. Effect of Loosening the Charge.......430 n Corrections...........432 6. Theory.............433 o. Effect of Varying Weight on Tractive Force..... 434 p. Effect of Varying Pole-Distance.......436 q. Effect of Varying Magnetization.......436 T. Effect of Varying Size.. .......437 a. Summary,........... 441 III. The Relative Magnetic Permeability of Various Minerals,. 443 The form and strength of magnetic fields have attracted much attention. especially in connection with the designing of dynamo-electric machinery—an art which has been revolution-

Jan 1, 1902

By L. Cichowicz, K. K. Millheim

The constant-rate drawdown test performance for a low-permeability, verticany fractured gas well was investigated. A series of gar wells were tested by flowing each well at constant rate until the data could be analyzed using con-ventional radial flow theory. Each well was then shut in to build up. After a sufficient buildup was obtained, another flow Iest commenced but at a higher flow rate than Ihe first test. Again, the well was shut in when radial fiow was obtained. his procedure was repeated for three to four different flow rates. Two wells in the San Juan basin were tested using this procedure. Both wellere fractured after completion, cleaned up and then shut in until flow testing commenced. Test designs of both wells permitted investigation of the most realistic values of egective permeability, wellbore radius and turbulence factor. Also, being able to determine the eflective fracture flow area and vertical fraclure efficiency was inherent with this testing approach. It was observed that fractures in both wells influenced the Pressure behavior for approximately Is to 40 hours (depending on the flow rate) before radial flow was evident. After this time, drawdown data were analyzed using radial pow theory. When a low-permeability gas well has vertitally oriented, induced fractures, the early flow geometry ic. essentially linear. It will be shown how to determine when a flow test has been conducted long enough so lha' the most representative values of effective permeahiiity. wellbore radius and turbulence factw can be calculated. From the linear pressure data, valuable information about The fracture treatment, such as the effective flow area and vertical fracture efficiency, can be determined for vertically froctured wells. Introduction During tests on gas wells in the Sari Juan basin7 initial transient behavior lasted for many days because of the low permeability of some porous media. As a result, stabilized flow performance could not be obtained. If these wells received some type of stimulation treatment, early pressure behavior deviated from conventional theoretical radial Row. When conventional radial flow theory was used to analyze these low-permeability fractured gas wells, larger values of flow capacity and absolute open flow potentials (AOF) sometimes resulted. Wells were assigned open flow poten- tials that proved to be 3 to 10 times higher than the well would sustain over a longer period of production. In some cases where the wells had flowed for longer periods of time during a constant-rate drawdown test, it was noticed that the effective flow capacity appeared to be decreasing with time until a certain value was reached. The early nonradial pressure behavior can be explained If linear flow is assumed. Rusell and Truitt mathematic. ally investigated the vertically fractured well in a bounded area. They showed that early flow behavior was essentially linear and, for x,/x. approximately less than 0.10 radial flow was obtained after short periods of time. Then realistic values of effective permeability and skin could be determined. Scotta experimentaliy studied the vertically fractured well with a heat flow analog. He showed that earb flow was linear, Both studies indicate that, for small values of x,/x,, linear flow approaches radial flow if the well is tested long enough, To help prove this concept of early linear flow caused by induced vertical fractures, two low-permeability gas wells were tested. Both wells received large fracture treatments prior to testing. A vertical fracture was indicated from the analysis of fracture treatments, As anticipated, tests of both wells indicated early linear flow that was later followed by a period of radial flow, Data collected from each well were analyzed. From the well tests, plus other information on each well, the effective permeability, wellbore radius and turbulence factor were calculated. Effective fracture flow areas calculated from test analyses for each well proved to be approximately one-fourth the created area calculated from classic hydraulic fracturing theory: other fractured wells that were tested but not presented in this paper also indicated that the effective fracture flow area was one-fourth to one-third the created area predicted from hydraulic fracturing theory. The vertical fracturing efficiency was estimated from the calculated values of effective wellbore radius and fracture flow area. For the two wells tested, calculated fracture lengths x, were 112 and 105 ft, and the vertical fracturing efficiencies E, were 122 and 183 percent. Development of Flow Model Agnew' showed that most induced fractures below 1,500 ft are vertical. Anderson and Stah15 indicated that most of the fractures they studied were vertical. Thc model proposed for early flow in most vertically fractured gas wells is shown by Fig. 1. This model should approximate early flow behavior until radial flow is reached, at which time a radial model with an effective wellbore radius of 0.5 they will

Jan 1, 1969

By J. P. Boisseau, C. N. J. Wagner, E. N. Aqua

An analysis ulas made of powder-paltern peaks from cold-rolled polycrystalline copper and from copper powders, compacted into briquets (1 in. diameter) with pressures up to about 106 psi. Powder-pattern peaks from both contact faces were measured with a diffractometer and CuKa radiation. Laltice-parameter measurements indicate the presence of residual stresses in the bulk specimen of the order of a - -10 kg per sq mm after 93 pct reduction in thickness, and give some evidence for the occurrence of deformation stacking faults (probability a - 0.003) in both bulk and powder samples. Fourier analyses of the line profiles were carried out on the (111) - (222) and (200) - (400) Pairs of reflections. The particle sizes decrease rapidly with increasing deformation and reach asymptotic values of De (111) = 550A and D, (200) = 350A at about 25 pct reduction in thickness or 80,000 psi pressure for compaction. The anisotropy of the particle sizes indicates the presence of microtwins and stacking faults on (111) planes. The rms strains increase also with deformation and reach limiting values of 2 x 10-3 in the [100] direction and 1 x 10-3 in the [Ill] direction at a distance L = 100A normal to the reflecting planes. THE diffraction of X-rays in cold-worked, polycrystalline, fcc metals and alloys yields Debye-Scherrer patterns in which the individual (hkl) lines may show a broadening, a shift, and an asymmetric shape.' These effects can be explained by the fragmentation of the small, coherently diffracting domains, the presence of residual elastic strains in the lattice, and the formation of stacking faults. X-ray studies of stacking faults in fcc metals and alloys have been methodically performed during the last few years, but so far most of the investigators dealt with cold-worked powder specimens obtained by filing.2-8,10-19 In such specimens, the crystals are randomly oriented and the average elastic strains are assumed to be zero, so that the observed peak shifts are due to stacking faults only. The agreement between X-ray diffraction theory1,20 and experiment is generally good. On the contrary, cold-worked, polycrystalline bulk specimens (after wire drawing, rolling, plastic deformation by tension or compression, etc.) contain residual elastic strains, which may not average to zero in the surface of the specimen and show very strong preferred orientation of certain lattice planes (texture) parallel to the specimen surface. Nonzero elastic strains also produce peak shifts, the magnitudes of which depend upon the crystallographic orientation of the reflecting lattice planes in elastically anisotropic materials as well as on the type of plastic deformation and which have to be taken into account when measuring stacking-fault probabilities in deformed bulk specimens.21-23 The purpose of the present investigations was to perform a detailed X-ray analysis on a bulk specimen of a fcc metal deformed by rolling at room temperature and on powder of the same material deformed by compaction, and to compare these results with those previously obtained on cold-worked filings.18 Pure copper was chosen for this study since it is known to produce only a small quantity of stacking faults by filing at room temperature.3,16,17,19 The residual elastic strain in the surface of the bulk copper should be the predominant factor determining

Jan 1, 1965

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the sane. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known. GENERAL METHOD The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Earle E. Schumacher, W. C. Ellis, John F. Eckel

Copper-calcium alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiensl have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1930

By Charles Willis

MANY of the failures in vocational education are due to the fact that the educational methods were not designed to the capabilities, habits, and environments of those to be trained; rather they were based on the policy that education is education and lessons are lessons, whether for youngsters of fifteen or for men of forty. Vocational education among miners involves, first, a study of the men themselves, their habits, and the use of their leisure time; second, a study of the differences between the methods of teaching required for men and for children. Certain fundamental requirements of training methods for miners are reasonably universal and may be applied with success to any ordinary mining community. The rate of labor turnover is another consideration; it would be useless to design a four-year course for men who remain in one place only a few months.

Jan 7, 1919

By Philip D. Wilson

The mines of the Calumet & Arizona Mining Co. are situated in the Warren Mining District, Cochise County, Arizona, between Bisbee and Warren and adjoin those of the Copper Queen Consolidated Mining Co. and the Shattuck Arizona Copper Co. Paleozoic 1imestones.of considerable thickness have been intruded by granite porphyry. A great stock of the intrusive outcrops boldly near the city of Bisbee and is known as Sacramento Hill. From this central core the porphyry has tongued out into the limestone for many thousands of feet as dikes and sills of irregular shape and variable dimensions. Churn drilling has recently developed a large tonnage of secondarily enriched copper ore in the main porphyry mass of Sacramento Hill. While some ore has been found in porphyry in other parts of the district, it is relatively unimportant compared with that which occurs in the Paleozoic limestone as irregular lenses replacing favorable beds near porphyry contacts or associated with well-marked fracture zones often many hundreds of feet away from the intrusive. In a zone extending from Sacramento Hill for a distance of from 1,500 to 3,000 ft., the limestone has been extensively metamorphosed and in this contact metamorphic zone the ore occurs through a known vertical thickness of upward of 900 ft. and individual orebodies often show extension in a vertical direction of over 200 ft. At a greater distance from the intrusive stock, the ore occurs as lenses of greater horizontal than vertical dimensions with an average thickness of approximately 30 ft. An exception to this rule is found in the occasional steeply dipping mineralized fractures, almost true tabular veins, which are found long distances a way from the zone of contact metamorphism. The copper was probably introduced during or slightly later than the porphyry intrusion in the form of chalcopyrite and bornite. These primary copper minerals are always associated with pyrite and often occur as rich lenses in a huge mass or shell of pyrite carrying an insignificant percentage of copper. In many instances the copper-bearing solutions were preceded by siliceous solutions and these latter, often persisting during the period of mineralization, have thoroughly indurated the ore-

Jan 1, 1917

By M. Kitada, U. Kawabe, F. Ishida, T. Doi

The relations between micros tructures and critical current density in transverse magnetic field were experimentally investigated due to each transformation of the 0 to 0' + P" phases at 700' C for superconductmainly examined using replication electron microscopy. The ß' or a precipitates were found to pin down magnetic flux lines in these alloys. The effects of precipitation upon the critical current density were discussed in relation with the size, spacing, and characler of these precipitates. HIGH magnetic field superconductors, such as Nb-Zr, Nb-Ti, and Nb-Zr-Ti alloys, have been recently put to extensive practical use as winding materials for superconducting magnets.13 The critical current density of these hard superconductors under an applied magnetic field is an important characteristic for magnet materials and is very sensitive to metallurgical structure. It is generally known that the critical current density is increased by introducing dislocations and precipitates into a superconductor; that is, dislocations and precipitates are presumed to be barriers that hinder quantized flux lines from moving.4'5 Theoretical6'7 and experimental analyses of the motion of flux lines and the interaction between flux lines and various defects have already been reported by many authors. Metallographic analysis of high magnetic field superconductors such as Nb-Zr and Nb-Ti is difficult, so that no quantitative relationship between microstruc-ture and critical current density has been established yet. In this paper, the effect of precipitation on the critical current density in magnetic field was investigated for two superconducting alloys, Nb-40Zr-10Ti and Nb-5Zr-60Ti. In these alloys the resistive critical field H, at 4.2oK was about 100 kG and the critical current density Jc at 80 kG was of the order of 104 amp per sq cm.13-l5 The superconducting properties were examined in relation to the microstructural changes due to transformation of i) the ß to ß' + ß" phases at 700°C for Nb-40Zr-10Ti alloy and ii) the ß to a + ß phases at 500°C for Nb-5Zr-6OTi alloy. The effect of size, spacing, and character of precipitates on flux line pinning was in particular examined. The microstructures were studied by means of residual resistivity, microhardness, and tensile strength measurements as well as by X-ray diffraction, optical, and replication electron microscopies. I) EXPERIMENTAL PROCEDURE Pure niobium, zirconium, and titanium, in the form of rods 0.8 cm in diam, served as raw materials. Results of chemical analyses of these rods are given in Table I. Ingots of the alloys, 0.4 cm in diam and 3 cm in length, were prepared by means of levitation melting, utilizing a copper mold in an argon-gas atmosphere. Samples from the ingot then were cold-worked by grooved mill to 0.2 cm in diam, heat-treated homogeneously (in the ß phase region) for 5 hr at 1100° in a vacuum of 1 x 106 Torr, and finally cold-drawn to 0.025 cm in diam. For heat treatments, samples were wrapped in niobium foil and sealed in an argon-gas atmosphere in fused quartz capsules. Water quenching was done after each heat treatment. Subsequently H-J, were performed at 4.2° by slowly transporting the current through the samples 4 cm long, under transverse magnetic field, until the least detectable resistive terminal voltage was observed. The resistive critical field H, was taken as the field at which 100 pv appeared at 4.2°K across a sample 3 cm in length, with a current of 5 ma. The critical temperature T, was measured by means of a conventional four-probe resistivity technique and taken as the temperature at which the sample resistance reached one-half of full restoration of the normal-state resistance with a current l ma flowing through a sample 2 cm in length. Precipitates were observed by means of optical microscopy and carbon replication electron microscopy. The etching solution consisted of 5 ml HF, 10 ml H2SO4 10 ml H2O2, and 50 ml H2O, and shadowed carbon replicas were examined in a itachi HU-11 electron microscope operated at 50 kv. X-ray diffraction photographs were taken by a 11.46-cm-diam Debye-Scher-rer camera using copper Ka radiation. The micro-hardness was measured under a load of 200 g using

Jan 1, 1969

By John W. King, S. Ralph Austin

Spurred by recent forecasts of greatly increased demands for uranium by 1980 and beyond, interest is once again focusing on America's western uranium deposits. One of the principal producers in this area is the Gas Hills district in Wyoming, the site of approximately 12% of the known uranium in the U.S., including past production and current reserves. Located on the south flank of the Wind River Basin, the Gas Hills deposits have been recently studied by the Atomic Energy commission for clues to and guides for discovering similar-occurring ores. The ore deposits are confined to a permeable sandstone unit, up to 350 ft thick, at or near the base of the upper Wind River formation of early Eocene age. The uranium occurs in three principal north- south "ore trends," each of which is about six miles long, one mile wide, and separated from each other by approximately three miles (Fig. 1).

Jan 5, 1966

By William L. Fink, L. A. Willey

Since so many different curves have been published for the solid solubility of zinc in aluminum, it seems desirable to definitely establish the correct curve by two or more independent methods. The curve published in part I1t was based entirely upon X-ray measurements because the other methods employed at that time were not satisfactory. The present paper (the seventeenth of this series on high-purity aluminum alloys) describes the determination of the solid solubility of zinc in aluminum by the measurement of electrical resistivity at temperature and by microscopic examination. Since the publication of our part I in 1932, an investigation of the solubility relations in the aluminum-zinc system has been reported by Schmid and Wassermann2, who obtained their solubility results from lattice-parameter measurements on heat-treated and quenched specimens. The diagram that they published is shown in Fig. 1. In this investigation they also found by X-ray measurements that the parameter of the gamma phase changed continuously with zinc content and at such a rate that it would be identical with that of the beta phase at 60 atomic per cent zinc. It was concluded therefore that the beta and gamma phases, from the point of view of structural relationship, are one single phase. They also suggested a gap of immiscibility between 270" and 350" C. The complete boundary in this region could not be determined satisfactorily by the method employed and therefore was not shown in their diagram. Aluminum-zinc Alloys Materials Used.—Electrolytically refined aluminum3 was used in preparing the alloys for the work reported in this paper. Chemical analysis showed the following impurities: 0.004 to 0.005 per cent silicon, 0.006 to 0.008 per cent iron and 0.005 to 0.006 per cent copper. Also,

Jan 1, 1936

By R. E. Pray, M. C. Fuerstenau, J. D. Miller, B. F. Perinne

Quartz cannot be floated with potassium amyl xanthate as collector at any pH. Complete flotation is achieved with certain minimal additions of amyl xanthate and Pb from pH 5.8 to 8.5 and with amyl xanthate and Zn from pH 7.5 to 8.1. The active species of these metal ions responsible for activation are shown to be PbOH and ZnOH No flotation was effected when Cu and Mg were added as activators. Previous work1,2,3,4,5,6,7 has shown that quartz may be floated in the presence of sulfonate or soap when the following two criteria are met: 1) some portion of the added metal ion has hydro-lyzed to its first hydroxy complex, and 2) a precipitate of the metal-collector has formed. Since sulfonate and soap, two substantially different anionic collectors, conform to these criteria, this phenomenon may well be expected to be of a general nature. In this view then, it would appear that any anionic collector, including xanthates, should also float quartz when these two criteria are met. The object of this paper is to demonstrate the conditions under which quartz will respond to flotation in the presence of potassium amyl xanthate. EXPERIMENTAL MATERIALS AND TECHNIQUES Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Potassium amyl xanthate was selected as collector. Purification of this reagent was effected with the following method: 1) a laboratory sample of potassium amyl xanthate was dissolved to saturation in hot ethyl alcohol and filtered several times while still hot, 2) the filtrate was cooled, during which time potassium amyl xanthate crystallized out of solution; the xanthate was then separated from the solution by filtration, 3) the amyl xanthate was dissolved in fresh hot ethyl alcohol and filtered, 4) step (2) was repeated, 5) the crystalline potassium amyl xanthate was washed with ethyl ether five times, and 6) the xanthate was dried for 24 hours under continuous vacuum. Inorganic impurities are insoluble in hot ethyl alcohol whereas dixanthogen is soluble in ethyl ether. Five-gram charges of 48x150 mesh quartz were conditioned for 3 min in 125 cc of solution containing the reagents and were floated with the small-scale cell and procedure described in previous papers.478 Reagent grade HCl and NaOH were used for pH adjustment, while reagent n-amyl alcohol was added as frother. Frother addition is necessary with this technique, but it should be mentioned that data, similar to those shown in Fig. 2 for 1 x10-4 mole per liter Pb++ and 1 X 10-4 mole per liter AX-, were also obtained with a Hallimond cell in the absence of frother. EXPERIMENTAL RESULTS Clean quartz could not be floated with amyl xanthate at any pH. Flotation was achieved under certain conditions, however, when various metal ions were added to the system. The activating ions used were lead, zinc, copper and magnesium, added as reagent grade chloride salts. Lead as Activator: The effect of Pb++ as activator was examined at five different additions of amyl xanthate (Fig. 1, 2 and 3). When 1x 10-5 mole per liter xanthate was added in the presence of 1 x 10"4 mole per liter Pb ++, no flotation was obtained at pH 6.5 or below, while a recovery of about 60% was effected at pH 7. When the pH was increased to 7.8, no flotation was again obtained, Complete depression was noted from pH 7.8 to about 10, at which point a recovery of about 30% was achieved. At about pH 11, the precipitate of lead amyl xanthate which was present below this pH dissolved and complete depression occurred. When 2.5x 10-5 mole per liter xanthate was added with the same lead addition, no flotation was obtained at pH 5.8 and below, whereas a recovery of

Jan 1, 1965

By J. E. Andersen, J. Halpern, C. S. Samis

In the presence of oxygen, galena is oxidized in an aqueous medium containing sodium hydroxide, in accordance with the following reaction: PbS + 2O2 + 3OH ? HPbO2 + SO4 = + H2O A novel method was devised for following this reaction which takes place in an autoclave under oxygen pressure, by measuring the concentration of HPbO2- in the solution with a cathode ray polarograph employing stationary platinum electrodes. Using this procedure a study was made of the kinetics of the reaction, in which the effect of a number of variables, including temperature, oxygen pressure, NaOH concentration, and agitation, on the rate, were determined. The results of this study are described and discussed, in terms of possible mechanisms for the reaction. IT is known that sulphide minerals can be oxidized in aqueous media in the presence of oxygen under pressure. Reactions of this type can be classified in two categories depending upon whether the products of oxidation are insoluble or soluble in the aqueous medium. An example of the first type of reaction is the oxidation of pyrite in alkaline solutions, giving rise to an insoluble iron oxide. The kinetics of this reaction have been investigated and its mechanism established.' It has been applied in the oxidation of iron sulphides present in refractory gold ores to improve the subsequent recovery of gold by cyanida-tion.' The second type of reaction finds application where it is desired to recover the metal by leaching during oxidation. In this case a medium is selected in which the oxidized mineral is soluble. For example, nickel, copper, and cobalt sulphide ores can be treated by oxidation in the presence of a solution of ammonia dissolving the nickel, copper, and cobalt as the metal ammine sulphate salts.:' A similar treatment has also been reported to apply to zinc sulphide ores.' It is known that lead sulphate is soluble in solutions of sodium hydroxide or ammonium acetate. It should therefore be possible to dissolve the lead from galena ores by aqueous oxidation with oxygen under pressure using either of these solutions. The applicability of the ammonium acetate treatment has been investigated and confirmed in a recent study.' The present paper describes the results of a similar study in which the kinetics of the oxidation of galena in sodium hydroxide solutions have been investigated. The object of this investigation was pri- marily to obtain information of a fundamental nature relating to the kinetics and mechanism of this reaction. The use of pulps of comminuted ore in a study of this type is undesirable because of the difficulty in controlling and measuring the surface area. The measurements were therefore made using galena crystals of measured surface area and in this way absolute reaction rates were obtained. The reaction was found to proceed as follows: PbS + 2O2 + 3OH ? HPbO2 + SO4 + H2O [I] The products are sodium plumbite and sodium sulphate salts which dissolve in the aqueous solution. The reaction studies were carried out in an autoclave in which a desired pressure of oxygen was maintained. The reaction was followed by measuring the concentration of lead in the solution with a cathode ray polarograph. The results obtained in this investigation are presented and discussed in the present paper. Experimental Materials: The crystals of galena were obtained from Violamac Mines, Sandon, B. C. The following impurities were indicated by spectrographic analysis carried out by the Provincial Assay Office, Victoria, B. C.: Sn, 0.02 to 0.2 pct; Sb, 0.07 to 0.7; Zn, 0.01 to 0.1; Si, Fe, Mg, As, less than 0.05 pct; Ag, 126 oz per ton, the latter determined by standard fire-assaying procedure. After cutting a specimen measuring approximately 5x7x12 mm, the crystal surfaces were ground parallel to the 100 axes using No. 2 emery, washed with water, and the dimensions were measured with a micrometer. Oxygen gas was of commercial grade and supplied in cylinders by Canadian Liquid Air. Solutions were made up with chemicals of chemically pure grade and distilled water. Equipment: Autoclave: The autoclave used in these studies was constructed of stainless steel and

Jan 1, 1954

By L. F. Tedsen, A. E. Flanigan, J. E. Dorn

SINCE aluminum-alloy sheet may be used occasionally at moderately elevated temperatures, the effects of temperature en the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 375°F. This paper deals with stress-rupture and [ ] creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24S-T Alclad 24S-T8I Alclad 24S-T86 Alclad 75S-T R301-T (clad) [ ] Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 211°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to boo hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). MATERIALS Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1946