Search Documents

By R. V. McAfee

The fundamentals of vertical-lift performance are examined with the aid of computer-calculated flowing gradient charts. Flowing and gas-lift well performance characteristics are determined from available well test data. The effect of tubing size, gas-liquid ratio and wellhead pressure is discussed for both flowing and gas-lift wells. The effect of gas-injection pressure, formation gas, bottom-hole pressure and valve spacing is also discussed for gas lift wells. From these studies conclusions may be reached for improving or prolonging natural flow, obtaining optimum lift efficiency when natural flow ceases and improving existing gas-lift systems. The techniques perfected satisfy the requirement that the time involved to conduct an evaluation be practical for operating personnel. INTRODUCTION Flowing pressure gradients furnish the key to successful evaluation of vertical-lift performance in producing wells. Command of multiphase flow gradients in some readily usable form is a necessity before operating personnel can competently include vertical-lift performance evaluation of both flowing and artificial-lift wells in their over-all consideration of production efficiency. A readily usable form cannot be overemphasized since most of the decisions which confront the production engineer with a problem well must be made quickly. In moving a barrel of oil from the reservoir to the stock tank, the major portion of energy generally is expended in the vertical-lift phase. This may or may not be of concern during the flowing life of a well, depending upon the production requirements. It becomes of some concern when the flow performance of the well becomes erratic, and a conscious effort must be made to maintain natural flow. It is at this time that the first steps may be taken to modify existing conditions to relieve unnecessary limitations to proper flow. When natural flow ceases and some form of artificial lift must be installed, the amount of energy expended in lifting liquids becomes quite obvious. It is at this time, if no other, that lifting efficiency becomes important because that part which must be supplied from an outside source is now related directly as a cost per barrel of oil produced. Ten years ago, the majority of gas-lift wells were produced with gas-well gas. Today, the majority are produced by closed rotative gas-lift systems. This permits a direct evaluation of well performance in terms of horsepower requirements and has resulted in mixed conclusions as to the success of gas lift based upon the relative efficiency of a particular system. An increased awareness of the need to resolve vertical-lift performance on a readily usable, scientific basis was inevitable. An indication of the need for better applied science in this field is the often-asked question of whether or not gas-lift can efficiently deplete a given well or reservoir. This question cannot possibly be answered without first evaluating reservoir, surface and vertical-lift performance both as encountered today and as anticipated throughout the life of the well or wells. The technique presented in this paper was originally developed to upgrade gas-lift installation design from an applied art to an applied science. It has since been successfully used not only for this purpose, but also for the whole field of vertical-lift performance in its broadest sense. Lift efficiency should be considered important while the well is still flowing, as well as after natural flow ceases. Correct interpretation and proper modification of the vertical-lift performance of a producing well can provide dramatic improvement in production performance and/or efficiency. STATEMENT OF THEORY AND DEFINITIONS Fig. 1 illustrates the three divisions of production which will be used in this paper. The terms are a modified version of those presented in the very fine paper by Gilbert.' The fields of reservoir and surface performance both have been greatly improved over the years. A study of those writings which may be found indicates that the field of vertical-lift performance has not progressed as well. There are two possible reasons for this lack of progress. 1. It has not been recognized as a scientific field in itself by the oil companies, as has reservoir engineering. 2. The equipment companies have confined their efforts to mechanical design research rather than the more basic study of vertical-lift performance of producing wells. Both organizations must have an economic stimulus for doing research in this field, and most of the results obtained in past work has been so erratic as to arouse little enthusiasm. The basic purpose of interpreting vertical-lift performance is to predict operating conditions below the surface of the ground from available data. The success of the interpretation depends upon the accuracy with

By M. Metzger, J. Intrater

IN the large number of important studies on high-purity aluminum (e.g., recrystallization and grain growth, creep, internal friction), it does not seem to have been generally recognized that the iron content, despite its very low figure, has a strong influence on a number of properties. In part, its influence is due to the very low solubility of the Fe-A1 6 phase. For aluminum of about 99.99 pct purity, the iron content may be 0.001 to 0.004 pct. For values in this range, a second phase will be present below 410" to 480 °C. This was determined by extrapolation of a log solubility vs inverse temperature plot of the solid solubility data of Edgar.' One consequence is the inhibition of grain coarsening below the solubility limit. This is shown in Table I, which gives, for three iron contents, the annealing temperature required for the absence of grains smaller than 1/2 mm average diameter together with the minimum temperature for the presence of some grains larger than 2 mm diameter. The specimens were 1/4x 1 1/2-in. strips cut from hard-rolled 1/16-in. sheet supplied by the Aluminum Co. of America.

Jan 1, 1954

By P. Chiotti, G. R. Kilp

Thermal, metallographic, vapor pressure, and X-ray data were obtained to establish the phase diagram for the zinc-zzrconiz~m system. Five compounds corresponding to the stoi-chiometric formulas ZrZn, ZrZn,, ZrZn,, ZrZn,, and ZrZn14 were observed. All these compounds, with the exception of ZrZn2, which melts congruently at 1180°C under constrained zinc-vapor conditions, undergo pexitectic reactians. The temperature at which the zinc vapor pressure is I atm for a series of alloys was determined from vapor-pressure measurements. The data obtained are summarized in the construction of a I-atm-pressure phase diagram and a phase diagram corresponding to a pressure of less than 10 atm. THE purpose of this investigation was to establish the phase diagram for the zinc-zirconium system. Thermal, metallographic, vapor pressure, and X-ray data were employed in determining the phase regions. Partial investigations of this system have been conducted by Gebhardt1 and Carlson and Borders.' Carlson and Borders studied the high-zirconium region and established the existence of a eutectic at 69 wt pct Zr with a melting point of 1015°C. The terminal phases of the eutectic horizontal were shown to be an intermetallic compound ZrZn and a solid solution of ß zirconium containing 21 wt pct Zn. The ß solid solution decomposes into ZrZn and a zirconium at 750°C. The eutectoid composition is given as 15 wt pct Zn, and the solubility of zinc in a zirconium at temperatures below 750°C is indicated to be negligible. Gebhardt studied the zinc-rich region and observed a lowering of the melting point of zinc from 419.5" to 416°C and temperature horizontals at 545" and970°C. Some preliminary observations by Chiotti, Ratliff, and Kilp were reported by Hayes.2 pietrokowsky3 has reported the compound ZrZn2 to have a cubic MgCu2 structure with ao = 7.396A. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc or Baker analyzed reagent granulated zinc, both 99.99 pct pure and hafnium-free iodide-process crystal bar zirconium obtained from the Westinghouse Electric Corp. The zirconium contained 200 ppm Fe, 200 ppm Si, 100 ppm C, and minor amounts of other impurities. The zirconium was milled or machined into thin chips or shavings. These were cleaned with a nitric-hydrofluoric acid solution, rinsed with water, and acetone, and dried just prior to their use in alloy preparation. The granulated zinc was similarly cleaned using dilute nitric or hydrochloric acid. Weighed quantities of these materials, 20 to 30 g total, were mixed and pressed at 20,000 to 70,000 psi to give relatively dense compacts. During the early part of this investigation the pressed compacts were placed in MgO-15 wt pct MgF, crucibles which were then sealed inside of quartz ampules. The compacts were given various prolonged heat treatments prior to their use for thermal analyses, or vapor-pressure measurements. Because of expansion of the compacts and the relatively high zinc vapor pressure it was difficult to heat to the melting temperatures of the alloys without failure of the quartz ampules. Homogenization at temperatures below the melting temperature gave brittle, porous alloys unsuitable for metallographic examination. It was also difficult to prevent condensation and segregation of zinc on the colder parts of the quartz ampules during heating and cooling operations. These problems were eliminated to a great extent by the use of tantalum crucibles. Tantalum proved to be a satisfactory container with little or no reaction between the alloys and the tantalum. Small tantalum thermocouple wells were successfully welded in the bottom of these crucibles. Pressed compacts were sealed inside the tantalum crucibles by welding on preformed caps under an argon atmosphere. Heat treating and differential thermal analysis were combined into a single operation. The experimental sample assembly is shown in Fig. 1. This assembly was enclosed inside a stainless-steel tube heating chamber which could be evacuated and filled with an inert gas. The thermocouple leads were brought out of the heating chamber between two rubber gaskets used to provide a vacuum seal for the water-cooled head. Most of the compounds in this system undergo peritectic decomposition. After heating above the temperature of a particular peritectic horizontal the sample was cooled to just below the peritectic temperature and held at temperature for several hours. The sample was then reheated through the peritectic temperature and the size of the thermal arrest, if still present, compared with the one previously obtained. If the thermal arrest was not characteristic for the alloy composition being investigated its magnitude diminished and repeated cycling and annealing eventually eliminated it. The peritectic thermal arrests characteristic of a particular composition were established in this manner.

Jan 1, 1960

Slovenliness is as reprehensible in words as in clothes. Much writing that we recognize as poor in style is merely sloppy. Just as some students postpone the necessary shave or forget to change their collars, so young engineers in writing drop their articles, definite and indefinite, or omit prepositions where they are required, possibly to compensate for those they use unnecessarily The work will begin [on] Saturday. Influenza seriously affected many mines [during] the last three months. Flotation in America [during] the last two years has made tremendous strides. Construction of the mill started [on] August 12, 1915, at which time 75% of the excavation was completed. The idea I wish to convey is [that] there are mineral deposits to which the present law applies badly. For this reason, if there was [for] no other, the ownership of the ore below and [of] the surface above should go together. When a unit of mapping is furnished, be the unit a claim or [a] group of claims, it is necessary . . . A fully stocked store was started in Park City and all employees [were] sold merchandise on a strictly cost basis. The word "merchandise" is left without government or agreement. 'I suggest: ". . . and merchandise was sold to all the employees on a strictly cash basis." The verb 'be' is serving concurrently both as a principal and as an auxiliary in the following: At first the work was interesting and [was] liked by most of the men. The sulphide ore was more complex or [was] milled at an increased cost. The failure to repeat the auxiliary verb in successive clauses is a common error, as in The filter is filled with liquid allowed to empty, and then ignited.

Jan 1, 1931

By C. S. Matthews, W. R. Strickler, M. Prats

To gain an insight into the deviations from normal behavior caused by dip. a mathematical study has been made of single-fluid five-spot floods in dipping reservoirs for flooding techniques likely to be employed in such cases. Streamline patterns and sweep eficiencies are computed for a number of different cases, and the results, where possible, are presented in graphical form. An increase in sweep efficiency can be obtained by moving the central injection well updip, and the opti~num position is found for several cases. The applicnhility of the results is discussed. INTRODUCTION Because of the growing importance of water flooding in California and in other locations where large angles of dip are quite common, it is important to know at least some of the effects of dip on the performance characteristics of water floods in such instances. In the past, only reservoirs having relatively mild dips have been wateflooded. Consequently, little is known today as to the effect of dip on the performance characteristics of a flooding operation from the point of view of field experience; and because of the complexity of the problem, little, if anything, has been done on the problem from the point of view of theory. There are two distinct aspects of the role played by gravity in a flooding operation. The first is that of the preferential segregation of the reservoir fluids at the time when the flood is to commence. The second is the role that it may play in affecting the performance of the reservoir during the course of the flooding operation. In this paper the reservoir is assumed to be filled with only one fluid, so that there is no preferential segregation of reservoir fluids at the commencement of the flood. Moreover, the injected and in-place fluids are assumed to have the same characteristics, so that in effect we consider only a single-fluid problem. Single-fluid results have been used as a guide in the past for predicting and interpreting the behavior of regular five-spot floods in horizontal reservoirs. It is thought that single-fluid results might likewise be used for five-spot patterns in dipping reservoirs as a norm to which the effects of the multifluid problems might he referred.* In confining our attention to the single-fluid case, we therefore do not consider the preferential segregation of injected water in the oil bank, or of the oil bank in the unflooded zone. Instead we consider the deviation from the behavior of a horizontal five-spot which is caused by use of flooding techniques (i.e., the flow potential pattern at injection and production wells) likely to be employed during flooding operations in dipping reservoirs. In other words, we consider effects which are caused by the pattern of injection and production well pressures which we choose to apply. Performance characteristics are given for the five-spot spacing pattern as a function of two parameters; one is the ratio of gravity head to potential difference bctwccn the high updip injection well and the low downdip producer of the same five-spot, denoted by Rg; the second is the orientation of the five-spot pat-

Jan 1, 1956

By H. W. Mossman

Three aspects of magnetite smelting are discussed. The first is the working out of equilibrium conditions for eliminating sulfur. The second is the influence of magnetite solubility on the difficulty of tapping the reverb matte. The third is an approximation of the equilibrium conditions in the reverb gases which govern whether magnetite is mode or reduced in the reverb slag by these gases and by any iron sulfide in the slag. MAGNETITE has had a varied history in the Hurley Smelter since its start in 1939. Magnetite determinations on the smelter products are made regularly only on the monthly composite samples. Variations on the monthly averages are shown in Table I. Magnetite which drops from the slag and matte in the reverb has some slight bottom buildup which comes and goes, but no substantial accumulation from this source has been found at the end of a normal nine months' furnace campaign. However, there has been some low grade magnetite bearing material mixed with considerable A1,0,, which has slid down from the bottom of the sloping flue between the reverberatory furnace and the waste heat boilers. This accretion has required drilling and blasting near the skimming end of the furnace. The magnetite has interfered with tapping at times. When the smelter was first started, tapping trouble from magnetite was extremely severe. Increasing the reverberatory furnace temperature by putting in an air preheater and a Dutch oven has helped greatly, although there still is occasional tapping trouble. When the present series of physical chemistry articles on copper smelting started coming out in 1950, they were read with interest, but no immediate application was seen for them. Results of some laboratory work in 1952 aroused a much stronger interest in this physical chemistry. A series of melts was made on some converter slags, which had magnetite in very large grain sizes, with the object of reducing the grain sizes in the slag, as it was known that it was easier to handle in the reverb in that condition. Anything done in the tests greatly reduced the grain sizes—even in the controls, where nothing was done except melt the slag and cast it. There was more magnetite in the slags after the tests than before, and with wide variations. There were no obvious reasons lor much of what happened in these tests. Much of the base material published in English in this field was made available for study. Recalculations were made on many of the type problems, and part of the data was reduced to local temperatures and compositions. Explanations were found for what happened in the 1952 series of tests on converter slags, and the same principles turned out to be a description of much of what magnetite does in the reverb. This article is to present the results of that study, from the viewpoint of applying the technical material in definite numerical form to the operating conditions in both the converters and the reverberatory furnaces at the Hurley smelter. Table I. Magnetite Variations on Monthly Averages, 1939 to 1955 Pet Magnetite Lowest Highest Average Converter slag 13.6 43.3 25.4 Roverb slaa 2.7 20.9 8.7 Matte 28 15.9 98 In general it was found that magnetite is made or reduced in both the converters and the rever-beratory furnace, depending on variations of temperature, matte composition, and reverb gas composition occurring in ordinary plant operation. Within reasonable limits, the field conditions for formation or reduction can be predicted, and probably can be set up and maintained. Converter conditions affecting magnetite formation can be put into numerical values better than for the reverb from purely technical calculations. The converter can be operated so as to keep the magnetite in the slag down to between 12 and 14 pct and still give satisfactory life for the converter brick. This depends upon having converter flux available which will make a slag with a good separation without raising the temperature too high. In the Hurley reverb and others with similar conditions, it is likely that a compromise of conditions will give a reasonably good control of combustion and still keep the magnetite from building up on the bottom. This discussion consists of three main parts. The first is the working out of the equilibrium conditions in the converter for determining in which direction the reaction 3 Fe,,O, (s) + FeS (1) F? 10 FeO (1) + SO, will go under actual converter operating conditions. The second deals with the influence of the solubility of magnetite in the slag and matte in the reverb on the difficulty of tapping matte. The third is an approximation of the equilibrium conditions in the

Jan 1, 1957

By Luther W. Lennox

The purpose of this article is not to compare one type of grinding machinery with another and to conclude from a series of tests that one particular machine is superior to all others. Neither is the reader asked to tire himself with the details of many tests to prove the statements herein made. The Chilean mill stands today almost an outcast from the milling world. It ranks with the applicant for a job who has been given a trial along with others and condemned because he was not able to perform the definite task assigned as well as the others, and was forever eliminated. The judges did not tarry long enough to try this aspirant in a field of a slightly different nature. Even though it has been condemned, the writer contends that the published records will indicate that the trials were never shifted into the field of greatest efficiency for the . Chilean mill. Those of us who cling to this outcast as a fine grinder in our milling operations do not wish, naturally, to be condemned also, with the machine, and yet we feel that we are classed as behind the times, at least in this phase of our milling judgment. Hence there is considerable personal feeling in our efforts. During the last few years there have been published several papers on the relative merits of the various grinding machines. In two of these articles a comparison was made between Chilean mills and cylindrical grinders. In each case the Chilean mill came out second best from about all standpoints. The outstanding feature in these comparisons would seem to be the decided attempt to keep all conditions the same, so that each machine could be judged on its merit. As Mr. David Cole states,1 "We are inclined to regard a direct comparison of grinders arranged side by side, and making a product that affords as nearly as possible the same screen measure, as the Supreme Court in these grinding matters." The writer agrees that this is the very best method for true comparison between machines. The results in the two detailed tests should give the relative merits of the two grinders in doing the work assigned. And they probably do. The conclusion drawn in each case was adverse to the Chilean mill as a fine-grinding machine. However, the duty placed upon the machines was that of converting material that had already been

Jan 1, 1920

By G. D. Cremer, J. J. Cordiano

ALUMINUM powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, how- ever, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and aluminum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. 4 second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age- hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders, is probably the significant factor in our failure to obtain strong sintered pieces. METHODS OF PRODUCING THE POWER Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By Roy Thomas

SOON after the Waelz plant for the fire concentration of low-grade zinc ores was put into operation in the early part of 1929 at Katowice, it was found that the conveyor equipment for transporting the hot residue from the furnace dust chambers was inadequate. Hand tram-ming with water cooling was used for a time, but that method was injurious to the workmen as well as costly. The problem was to find some practical mechanical means of conveying flue dust at temperatures of from 450° to 600° C. as it was drawn from the dust chambers. After considerable preliminary investigation it was decided to install pneu-matic equipment for conveying the hot materials to a central mixing plant, where it would be mixed with slime and from which it would be returned to the furnace feed hoppers. The first pneumatic equipment was installed in 1930, and has been in successful operation since that time. The pneumatic method of transportation has shown a considerable saving in operating costs over the former methods of dust handling and a decided improvement in working and hygienic conditions at the plant, through the elimination of the dust hazard. Additional pneumatic equipment was installed in 1933 for conveying the furnace fume from the baghouses to the roaster plant. At the same time pick-up lines were provided for collecting the cleanings from the vertical and horizontal cooling pipes that are between the furnace dust chambers and the baghouses. The latter installation has practically eliminated a dusty and costly hand-tramming operation.

Jan 1, 1939

By C. D. Hall, F. E. Dollarhide

Conventional static tests of fluid-loss agents do not realistically simulate conditions in a fracturing treatment. The dynamic tests reported here show that fluid-loss volume is better represented as proportional to time, rather than as the square root of time. This leads to a different equation for fracture area. The leak-off rate increases with increasing shear rate at the fracture wall, but appears to approach a limiting value. Pressure effects are minor. Spurt loss ordinarily is not affected by the flow velocity in the fracture and is inversely proportional to concentration of agent. The filter cake, once it is well established, is resistant to damage by the flow of plain fracturing liquid (without fluid-loss agent). The latter two findings indicate that a treatment employing a high-concentration spearhead followed by plain fluid can offer a more economical treatment under suitable conditions. INTRODUCTION The successful design of hydraulic fracturing treatments depends on accurate knowledge of the fluid-loss properties of the fracturing fluid. Howard and Fast,' in giving the basic equation relating fracture area to fluid and treating parameters, described three mechanisms which might control the rate of fluid leak-off from the fracture. One mechanism usually is dominant in a given well treatment. For each mechanism, the leak-off velocity is inversely proportional to the square root of time, and the proportionality constant is designated as the fracturing-fluid coefficient. For the wall-building type of fluid-loss agent, the coefficient is determined by a filtration test in a pressure cell, usually with a rock wafer or core as the filter medium. In these static tests, the cumulative volume generally is proportional to the square root of time, after an initial spurt volume. The static-fluid-loss test is not representative of the con,-&tions under which a fluid-loss agent performs in a fratturing treatment. The marked difference between the dynamic- and static-fluid-loss behavior of drilling fluids reported in the literature2,3 implies that dynamic testing is also needed with fracturing fluids. We have therefore undertaken a study of the dynamic-fluid-loss behavior of fracturing fluids. The testing apparatus has also afforded opportunity to evaluate the resistance of the filter cake to removal or damage by flowing fluid containing no fluid-loss agent, with and without sand. The results of these studies offer a means for more accurate evaluation of fluid-loss agent performance, and point the way to a "spearhead" fracturing technique which may offer more economical treatment for some wells. EXPERIMENTAL METHODS The dynamic-fluid-loss testing method is applicable to any type of wall-building fracturing fluid. The present study aimed first at finding what phenomena are involved, and therefore has been limited in the number of materials tested. All of the results specifically reported herein are for kerosene containing a commercial solid fluid-loss agent, which is commonly used at 50 lb/1,000 gal of oil. Another agent in liquid form, used usually at 20 ga1/1,000 gal oil, has shown all the same phenomena in dynamic tests, and generally the same level of fluid-loss control as the solid agent. The dynamic-fluid-loss core cell used in all tests is shown in Fig. 1. The fracture was simulated by the an-nulus between a 2.03 in. OD sandstone core and the surrounding pipe. Annulus widths of 0.234 and 0.117 in. were used, and the core was 3.5 in. long. The annular geometry provides a uniform fluid velocity and a well-defined shear rate over the entire filtering surface, and permits a large filter area (144 sq cm) in a reasonably compact cell. The leak-off fluid passed into a 0.5 in. diameter axial hole in the core. A hollow steel rod through this hole was threaded into a rounded "streamliner" upstream of the core, and into a mounting stud downstream. The streamliner and the stud had the same outside diameter as the core. In all tests except those where sand was circulated, the mounting stud had protruding rings which constricted the annulus, to minimize any tendency for channeling of the fluid to the side exit port. The ends of the core were sealed by Neoprene, steel and Teflon washers. The leak-off fluid was conducted from the hollow rod to an exit tube, through a metering valve (a fine-pitched needle valve) and a quick-opening toggle valve in series, and into graduated cylinders for volume measurement; Two separate circulating systems were used in the experimental program. The extensive initial testing was done at 50 to 150 Psi. The fluid was circulated by a variable speed Moyno pump, and the flow rate was read by a rota-meter flow meter. The filtration Pressure was supplied by holding a back-pressure with a throttling valve. The discharge streamcould be diverted into any of four sections

Jan 1, 1965

By H. A. Coy

THE Mascot mines of the American Zinc. Co. of Tennessee are situated at Mascot, Tenn., 14 miles northeast of Knoxville, on the Southern Railway. The district is centrally located in the Great Valley, or Appalachian Valley Province. Prior to 1900, a small output of zinc was obtained from oxidized ore mined in open pits. In 1900, a shaft was sunk to sulfide ore, and in 1903, a second shaft was put down, neither being as deep as 200 ft. The American Zinc Co. of Tennessee began drilling in 1911, and outlined an ore body to which its No. 1 shaft was sunk, to a depth of 365 ft. Since that time, the American Zinc Co. of Tennessee has been the only operator in. the district. The Federal mining laws have never been in operation in Tennessee and mining lands are as irregular in boundary and area as farm lands. Ownerships are generally held in fee. In most cases the surface and mineral rights, are transferred together. Electric power is supplied at 66,000 volts by the Tennessee Power do, from a hydro-electric plant at Parksville, Polk County, Tenn., 100 miles from Mascot. No other power is used, but an emergency steam plant is held ready in case of interruption of service. Labor is all native and non-union. Negroes are employed for most of the shoveling, and for a few miscellaneous jobs, but for almost, no other work.

Jan 9, 1924

By D. T. Peters

To better understand the Co-Mo interaction in maraging steels, the precipitate reversion behavior of two alloys closely related to the 18 Ni-250 grade has been studied. The reversion experiment is carried out by aging at a low temperature, T1 (preaging temperature), for some period of time and then aging at a higher temperature, T2, called the reversion tetnperature. Aging and reversion tmzperatures used were in the range 679 to 1050°F. Reversion is marked by an increase in resistivity and a decrease in hardness. It teas found that some reversion took place at all cornbinations of T1 and T2 but that pronounced rei3ersion resulfed for an Fe-18 pct Ni-5 pct Mo-8 pcl Co alloy exposed to preagz'ng' temperatures at or below 850°F. A similar alloy not containing cobalt exhibited no such discontinuity in reversion behazior with TI. The results are interpreted in terms of two types of molybdenum-rich precipitates, one nucleated at dislocations and the other in the matrix. The increased supersaturation resulting from the presence oj- cobalt evidently provides sufficient energy to nucleate the matrix phase. Anotnalies in the temperature dependence of the resistivity decrease and peak hurdness in the Fe-18 pct Ni-5 pct Mo-8 pct Co alloy as a junction of aging temperature noted in an earlier study are explained on this basis. SEVERAL investigatorsl-9 have studied the details of the precipitation-hardening reaction of the maraging steels. The great majority of conclusions have been drawn from transmission electron microscopy. Although much has been learned by this method, alternate techniques which will give information earlier in the aging process are needed for a more complete understanding of the series of precipitation steps probably involved in the aging reaction. Peters and cupp'' have recently shown, by measurements of the kinetics of precipitation, that an 18 pct Ni-Co-Mo maraging steel shows a distinct change in precipitation behavior at aging temperatures below 850°F. The results were interpreted in terms of the existence of two types of precipitates at low aging temperatures. Only one precipitate type is present at higher aging temperatures. The low-temperature precipitate was found to be a particularly effective strengthener. No evidence for the additional low-temperature precipitate was found in the 18 pct Ni-5 pct Mo ternary alloy. The object of this investigation was to study further the characteristics of the two types of precipitates and the interaction between cobalt and molybdenum characterizing this system. Some preliminary experiments indicated a difference in reversion behavior in specimens aged above and below 850°F. This suggested that knowledge of the reversion behavior might shed some light on these two questions. Hardy and Heal11 have defined reversion as the loss of hardness, electrical conductivity, or other properties caused by heating for a very short time at temperatures above the aging temperature. The precipitate reversion referred to in this paper is entirely distinct from "austenite reversion" often referred to in maraging steel literature. This latter phenomenon could more accurately be called the diffusion-controlled formation of austenite. Much has been written about reversion in several of the aluminum-base binary and ternary alloys.'2-16 Two explanations for reversion have been advanced. Based on the classical nucleation theory of Volmer-Weber-Becker-Doring,17 Konobeevski18 suggested that reversion was due to the size of the precipitate particles

Jan 1, 1968

By Hewitt Wilson

IN 1903, T. M. and E. H. Alvord, of Marblemount, Wash., built a soapstone-grinding mill in the Skagit River Valley and are reported to have produced "ground talc" during 1904 and 1905, shipping to the paper mills in Wisconsin. Between 1916 and 1920, the Western Talc Co. built and operated a talc-grinding mill north of Mondovi, on the banks of the Spokane River, in eastern Washington, and sold powdered talc to the Inland Empire Paper Co. of Spokane. ? The most active develop-ment in recent years has been by two companies in the Skagit Valley-the Skagit Talc Company, Inc., which has been sawing soapstone block for the soda-recovery furnaces of the pulp and paper companies, and the Asbestos-Talc Products of Washington, Inc., at Burlington, which has been mining and dry-grinding a soft serpentine for the structural filler and insulation trade. Many prospects have been opened in the northern part of the state on both sides of the Cascade Mountains, and these activities undoubtedly are the forerunner of an industry that promises to attain considerable magnitude in the North Pacific States. At the present time, talc is imported from California for use as paper filler, and soapstone block from Virginia for use in the soda-recovery furnaces. A small market has been created locally for tailor and foundry:, pencils, stove grills, and block soapstone for art objects. The results of the present study, as yet incomplete, indicate that the use as a refractory and as a ceramic filler and flux can be expanded.

Jan 1, 1936

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By L. Segle, R. Resnick

NUMEROUS experiments in the past few years have proven that void formation occurs quite generally in the diffusion zone of bimetal specimens1-4 The phenomenon has been explained in terms of the accumulation of lattice vacancies resulting from unequal diffusion of the constituents and their eventual precipitation as holes.= Attention has recently been directed to the fact that voids also form within homogeneous metals during high-temperature creep.' The idea has been put forward that these voids form by the condensation of excess lattice vacancies generated by intersecting dislocations.".' If the precipitation of lattice vacancies from solution is treated as a nucleation and growth process, the predicted vacancy concentration for homogeneous nucleation of voids at an observable rate is 100 to 1000 times the normal thermal equilibrium concentration. It appears that voids actually form during diffusion at vacancy supersaturations which are much lower than this8 According to the calculations of Machlin,' the same must be true for voids formed in homogeneous metals during creep, if these are considered to arise from the precipitation of lattice vacancies. Therefore, if the vacancy mechanism is valid, it seems that the holes which form in diffusion and creep specimens are heterogeneously nucleated by imperfections or impurities in the metal. Irregularities in the frequency and distribution of voids in diffusion couples bear out this explanation.' , It is not known at the present time what the nuclei are on which vacancies condense. Various investigators have speculated that they could be certain dislocation configurations, already existing voids produced during solidification or working, gas pockets, or inclusions in the metal. Relatedly, the precise value of the degree of vacancy supersatura-tion for void nucleation is still uncertain. An initial attempt to estimate this value from diffusion data, made by Balluffi, indicated that voids form in diffusion couples at vacancy concentrations which may

Jan 1, 1958

By Lincoln F. Elkins

The Spraberry Trend Field of West Texas was discovered in January, 1949. Drilling of 2.234 wells and production of some 45 million bbl of oil by January, 1953, indicated this to be an important field which will ultimately cover more than 400,000 acres. In addition to being the world's largest field in areal extent, the Spraberry has presented many problems in well completion and operation and has demonstrated unique reservoir performance characteristics. The pay section consists primarily of a few fine grained sandstone or siltstone members in a thousand-ft thick section of shale, limestone. and siltstone. Since porosity averages only 10 per cent and nearly all permeabilities are less than 1 md, conventional core analysis does not delineate the "pay" section. Mercury injection was used as a capillary pressure test adaptable to rapid routine use to select those intervals having low enough connate water saturation to contain commercially significant oil saturation. In the central area of the field this "pay" amounts to 16 ft of Upper Spraberry and 15 ft of Lower Spraberry sands. An interconnected system of vertical fractures, observed in cores, provides the flow channels for oil to drain into the wells hut most of the oil is stored in the matrix since the void volume of fractures is estimated to be less than 1 per cent of that in the sand. Initial potentials of wells range up to 1.000 B/D after fracture treatment which should be compared with estimated capacity of 5 to 10 B/D if oil had to flow into the wells through the sand itself. Without exception initial pressures of later drilled wells were significantly lower than initial pressures of earlier drilled nearby wells in a large area some 6 miles long. This means the earlier drilled wells had drained fluids from areas much greater than their 40-acre proration units. Since most of this performance occurred while the reservoir pressure was above the. saturation pressure it was analyzed by the compressible fluid flow theory. This analysis gave calculated initial presrilres which agreed within 30 psi of measured pressures of 60 per cent of wells in the area using 16-md permeabilitv corresponding to a fracture system substantially that indicated by cores and using combined compressibility of rock and its contained oil and water corresponding to the core analysis data. The most important feature of this analysis was the very close agreement between effective compressibility of the rock and its contained oil and water from the field performance and that from the core tests, because it meant there are no "islands" of low permeability reservoir rock left untapped in the inter-well area and thus no additional wells are necessary to insure that at least one well penetrates each "reservoir." Twenty-five of forty-four 40-acre spaced wells on three contiguous sections were wed in a four-month inteference test. Six shut-in well. were tested monthly for oil production. productivity index. gas-oil ratio and pressure buildup, and seven shut-in wells were tested for decline in reservoir pressure. Tests on 12 regularly producing wells gave comparative data for interpretation of shut-in test wells. Reduction in reservoir pressure, decline in productivity index. and increase in gas-oil ratio were found to be substantially the same in the shut-in test wells as those in the comparative regularly producing wells, meaning that the producing wells were depleting the

Jan 1, 1953

By C. F. Clausen

"Cement" means binding agent or glue. It is derived from the Latin word "Caementum," the name of a limestone, chips of which were used in mortar more than 2,000 years ago in Italy. During the middle ages "cement" or "cement" generally denoted mortar. Today it means any binding material. The Thomas Register lists nearly 200 classifications for "cement" including automobile cement, household cement, rubber cement, etc. The material most commonly associated with this word, however, is portland cement which, when mixed with water and allowed to hydrate, is a ceramic binding material used to cement aggregates (crushed stone, gravel and sand) together in "concrete," the most universally used building material of today. It is estimated that more tons of concrete are used annually than all other building materials put together including steel, lumber, gypsum, bricks, tiles, aluminum and glass. Its use in foundations, building construction, sanitary work, dams, railroads, and highways, makes it difficult to conceive of modem civilization without concrete. A survey made in October 1955 showed the following uses of portland cement: [Percent Highways20 Nonresidential buildings20 Residential buildings15 Military construction10 Sewer and water works8 Public utilities10 Other (conservation, farm, and maintenance and repair)17 100] As of today, the percentage for highways is probably even higher. Ceramic binding materials have unquestionably been used in construction work for thousands of years. The mortar between the blocks of the great pyramids was calcined gypsum (plaster of paris). The use of calcined and slaked limestone goes back earlier than the Roman Empire. Gypsum, however, is relatively soft, and common lime mortar is not "hydraulic," i.e., it does not harden under water. The Greeks and Romans discovered later that an addition of a finely divided active siliceous material (Santorin earth or Pozzolana) would react with slaked lime to form a stronger, and hydraulic, cement. The Appian Way in Italy, Colosseum, and the great Aqueducts built by the Romans were made with this type cement, and some of these structures are still in existence today. However, not until 1756 did some serious research result in the development of better cements. In that year the English engineer, John Smeaton produced a stronger cement by burning a limestone containing considerable proportions of clayey impurities. Other investigations and improvements were made by Bryan Higgins, Bergmann, Joseph Parker, L. J. Vicat, J. F. John, James Frost, and I. C. Johnson.2 Traditionally, but perhaps unfairly to others, the invention of the prototype of today's portland cement is credited to the English mason Joseph Aspdin who in 1824 obtained a patent and gave the product its name, because in color the mortar produced from it resembled a natural building stone obtained from the British Isle of Portland. The contributions of Johnson and Aspdin were primarily the important step of preparing a synthetic mixture of lime and clay without depending on raw materials found in nature which might contain such elements in desirable proportions. However, even these early

Jan 1, 1960

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country, F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962