Search Documents

By G. A. Vissac, R. G. Minet, N. E. Sylvander

R. G. Minet—The authors' description of the remarkable progress made in the last few years in applying the fluidized solids technique to the problem of lignite drying and carbonization clearly demonstrates that engineering techniques available today may make many processes practical and profitable which a few years ago were considered otherwise. As pointed out in the article, the future of the carbonization step hinges on the value and utilization of low temperature tar. On paper, at any rate, this tar looks like a valuable raw material for the chemical industry to use. Some 50 to 60 pct may be converted to pitch for electrodes, roofing, road tars, and other valuable products; the 25 to 30 pct tar acids could conceivably form a basis for a new low cost resin or plastic of the phenolformalde-hyde type. Yet these materials are so new and dissimilar from available sources that much work must be undertaken by the chemical industry before they will be accepted. Now that the work of Dr. Perry and his colleagues has made a large supply of low temperature tar a real possibility, I would expect the chemical industry to accelerate its work in this field. On the basis of certain data available in the literature it appears possible to produce a more aromatic tar, although in smaller yield, by operating at temperatures in the range of 1300" to 1500°F. Operating a fluidized bed process for lignite at these conditions should be technically possible, at least, and could produce a tar having more familiar characteristics. I wonder if Dr. Parry would care to comment on such a possibility. Incidentally, in our own work on carbonizing coking coals in fluidized beds, using Ohio, Pennsylvania, and West Virginia high volatile bituminous coals, we have obtained yields which agree with the correlation given for tar yields vs moisture and ash-free volatile Btu. Our data are slightly under the line, but certainly in the range of the correlation. We have also obtained evidence in support of the authors' statement as to the effect of air on the process. In our pilot plant all the heat required for carbonizing is released by internal combustion of char in the fluidized bed in normal operation. We are also equipped to obtain all carbonization heat by external electric heaters on the shell of the carbonizer while introducing only an inert gas to the process. We note no difference in tar yield or characteristics between the two operations. In the case of the gas, however, it appears that some hydrogen is consumed by the air combustion. We would be interested in hearing in a little more detail about the hot dust and char handling problems at Sandow. Have the authors found char subject to spontaneous combustion? Have they ever tried a coking coal in their pilot plant? V. F. Parry (author's reply)—Production of a more aromatic tar by operation of the carbonizer at 1300" to 1500°F does not appear to be economical. 1) The capacity of a reactor operating at 1500°F would be 30 to 50 pct less than the capacity at 932 °F and the cost of processing would increase materially. 2) The cracking of tar vapors in a reactor requires appreciable time to complete the reactions and it is doubtful that considering the very short time of residence of tar vapors within the reactor (4 to 10 sec after evolution) the basic character of the tar would be changed significantly. This is indicated from the data reported in Table XIV. 3) General studies have shown that it is advisable to operate at the minimum temperature to produce the maximum tar and minimum gas. 4) Operating problems and the maintenance of vessels and reactors, and the hazards of handling hot char, increase with the temperature of carbonization. It is technically possible to operate at temperatures as high as 1500°F, but in my opinion it is not economical or desirable. We believe that the primary tar must be won in the simplest way and then processed alone to change its character for production of desired products. It is interesting to have confirmation of our observations on the reaction of air with the products of carbonization. The major reaction is with the char, fol-

Jan 1, 1957

By M. R. Geer, H. F. Yancey

WITH the exception of pneumatic processes and ii few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral- dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficiation process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and else- where, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment for many years, and more recently driers employing centrifugal force have gained in popularity. 1 A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal-a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. OBJECT AND SCOPE OF INVESTIGATION Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it on coal slurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1948

By Arthur Crowfoot

Page IntRodUction ................... The Round Table in Lake Superior Practice .........420 Early Use of Revolving Round Table in Butte District...... Use oF the Round Table at GREat Falls foR Sand-Slime Feed ., . The Round Table for Fine Slime........,.... Construction of Slime Plant at Great Falls..... '..... 424 Tests on Wood, Linoleum, and Cement Decks.........426 Central Feed Apron Removed ....'......... Re-treatment of Round-Table Tailing........... Determination of Conditions for Round-Table Treatment of Slimcs ... 430 Variation in Slope of Round-Table Deck........ ,... The Steel-Frame Cement-Deck Round Table ........ Tests on Cement and Canvas Dock Surfaces ..: ..... Conoidal Deck Round Tables............. Results with Sand-Slime Feed on Conoidal Deck....... Conclusions from Preliminary Tests on Conoidal and Conical Decks ... 446 Discussion of Results of Four-Day Test on Conical and Conoidal Decks . 452 Discussion of Results of Eight-Day Test.......... Qualitative Sampling of Concentrates Across Conical Deck.... Summary of Slime-Plant Practice............ Suggested Flow Sheet for Slime Classification and Treatment.... Conclusion...................467 Introduction The principal object of this paper is 60 presest, data on the development of the revolving convex round table as a concentrator for the through 0.07-mm. slimes from the ores of the Butte district, although some brief notes on the earliest recorded use of this type of concentrating table in the ore-dressing plants of the Lake Superior region and of the Butte district are also presented. The revolving convex round table belongs to the class of concentrating tables known as film-sizing. tables, these tables using the relative transporting power of a film, or thin sheet of water, as it flows over a quiet inclined surface, to separate the minerals of a sorted product. The grains of heavy mineral move down the slope of the table deck slowly, or, in some cases, not at all, after the initial force of the feed entry VOL. XLIX.—27

Jan 1, 1915

By William Phillips

This paper was prepared at the request of Capt. A. F. Lucas, Chairman of the Institute's Committee on Petroleum and Gas, as a preliminary discussion of the fuel oils which are used-in the Southwest, giving their composition, uses, prices, etc. Should it afterward be found desirable, these observations may be extended over a larger area. In this connection, J suggest that samples of all kinds of fuel oils, including various tars, from all over the country, be collected and sent to some testing laboratory for examination. We would be glad to extend the facilities of the laboratory of the Bureau of Economic Geology and Technology, at the University of Texas, for this purpose, and to do the work free of all expenses. After such examinations are made and the results classified and studied, it would be possible to suggest specifications under which fuel oils should be purchased, and to arrive at some conclusions respecting the uniformity of such specifications, with due allowance for climatic and other more or less local conditions. While such specifications do not now depart from a common standard anything like as much as specifications for illuminating oils do, yet there are discrepancies which should not exist. Some of these discrepancies are of lessening importance, due to the pronounced tendency to distill every crude oil that can be distilled with profit, and to send residues into the market for fuel oil. Residues from the refineries are of a more uniform chemical composition and physical nature than many of the crude oils that go direct into the fuel market. The lower flash-point oils are disappearing from the fuel trade and in place of them we are getting oils that do not flash below 220° F., nor burn under 320° F. In the Southwest, it has not been long since we had fuel oils that flashed at as low as 110° F., and the average flash point over a considerable period was 151° F. Now we are using oil that flashes at about 30° lower than the former burning point, which was 256° F. In other words, the flash point has risen, on the average, 100°; and the burning point about 75°.

Jan 6, 1914

By Arthur F. Daily

13.5-1. Placer Deposits-Definitions. Placers are defined for this chapter as unconsolidated deposits of detrital material containing valuable mineral, and placer mining is defined as surface exploitation of placer deposits. Unconsolidated marine deposits containing industrial minerals, such as the very large pebble phosphate beds in Florida, pelletal phosphate beds in the Sechura Desert in northwestern Peru, oyster shell beds occurring at many places, and nodules resting in the sea floor, are not classed herein as placer deposits, though methods commonly used for mining placers may be employed for their exploitation. The natural processes that may form placers range from chemical weathering to stream, marine, and wind action, and combinations thereof, resulting in some degree of concentration of valuable mineral. One or more cycles of erosion and deposition may have occured. In relation to mining, placers include unconsolidated barren or near-barren overburden and underlying weathered bedrock. Placers of any origin subsequently may become drowned by the sea and then partly or entirely covered by marine deposits; or they may become covered with alluvium, eolian deposits, or lava. The mining of placer deposits for valuable mineral content usually is followed immediately by primary concentration using wet (rarely dry) gravity methods, succeeded by secondary concentration employing both gravity and other methods. 13.5-2. Classification of Placers. A fundamental classification of placers according to genetic types follows; some degree of concentration occurs during formation of all except saprolite and some moraines. 1. Saprolite and residual placers, consisting of mineralized rock decomposed in situ principally by chemical weathering; respectively either without change in volume, or slumped because of dissolution of some constitutent.

Jan 1, 1968

By Lawrence Addicks

THrough the courtesy of Dr. James Douglas I am permitted to give a summary of some of the results obtained in leaching slimes tailings in a series of experiments conducted under my direction at Douglas, Ariz., during the past year. While the test run for which the data are given deals with a particular case, much of the work is general in its application and may therefore be of interest. This work was done upon the ores of the Burro Mountain Copper CO. A description of the geology of the district will be found in the paper by R. E. Somers published in this volume, p. 604. The mineral is pyrite and chalcocite very finely disseminated throughout the gangue and a characteristic of all the ores is the large amount of alumina present. A representative analysis of the particular ore under consideration would be about as follows: Cu, per cent..................... 2.35 S, per cent...................... 3.0 Ag, ounces per ton.............. 0.05 CaO, per cent.................. 0.5 Au............................ None K2O, per cent.................... 4.0 Fe, per cent..................... 1.50 SiO², per cent.................... 70.0 Alz²O³, per cent....................13.OO The leaching of the ore direct was early dismissed from consideration for the following reasons: 1. The ore would have to be quite finely crushed to liberate the mineral for leaching; concentrating after crushing would cost but a few cents a ton; and a higher total reeovery would result from leaching tailings rather than ore. 2. Rough concentration would yield a suitable material for roasting to make sulphur dioxide or sulphuric acid in connection with the leaching scheme. 3. Such a program put the question of cost vs. recovery on a basis where flotation and discarding of tailings were directly comparable. Concentrating experiments already available indicated that the tail-

Jan 1, 1916

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By DeVerle P. Harris

Risk for most mineral investments is greater than that of average business ventures, because the physical and economic characteristics of the mineral deposit are never known with certainty. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with the adoption of the project, methods of risk analysis are important in project evaluation and investment selection. The conceptual framework for risk analysis and the means by which some of the recommended practices might be implemented are examined. In addition to the normal business risk due to market forces, the physical and economic characteristics of the mineral deposit are never known with certainty, for only partial or indirect information is available, such as data from drill cores or surface and underground workings. Consequently, risk for most mineral investments is greater than that of average business ventures. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with adoption of the project, methods of risk analysis are important in project evaluation and investment selection. This paper examines the conceptual framework for risk analysis and means by which might be implemented some of the recommended procedures. Utility Theory A discourse on risk and its impact upon investment selection quite often leads the reader into the concept of utility theory, for utility theory is a device constructed by economists to measure the satisfaction an individuai receives from a good; in the case of investment analysis, that good is the outcome of an investment. It briefly is reviewed here to describe the reaction of the individual to risk and as a stepping stone to other techniques more suited to risk analysis at the level of the firm. Utility theory proposes that an investor possess a utility map (curve), such as indicated in Fig. 1, which indicates the value in utiles of potential monetary rewards to an individual with some specific endowment of resources. Points on this map are obtained from the following relationship:

Jan 1, 1971

By C. L. Sollenbeger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature1,2 to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent. In the All is-Chalmers Research Laboratories a systematic study was made of the effect of different alkali-silica ratios on the concentration by flotation of two scheelite ores. One of these was a high grade ore from the Sang Dong mine in Korea. The effect of such factors as pH; addition agents; and conditioning time, temperature, and pulp density on the flotation efficiency of this ore have been described previously. The other ore was a low grade ore from Getchell Mines Inc., Nevada. The mineralogy and techniques of concentrating this ore have been described by Kunze. Hereafter these ores will be referred to as the Korean and Nevada ores. Experiments were made with both to determine the effect of three factors—-type of silicate, concentration of silicate, and pH of the pulp—on recovery and grade of tungsten in a rougher concentrate. Average WO, content of the Korean ore was 1.50 pct and of the Nevada ore 0.27 pct. The predominant tungsten mineral in both ores was scheelite, which was accompanied by a small amount of powellite. The powellite and scheelite were finely disseminated through both ores and required a —200 mesh grind for liberation. Major gangue minerals in the Korean ore, in decreasing order of abundance, were amphi-boles, quartz, biotite, garnet, fluorite, and calcite. Bulk sulfides composed about 3 pct of the total weight. Gangue in the Nevada ore, in descending order of abundance, was garnet, alpha quartz, calcite, phlogopite, wollastonite, and amphiboles. Sulfide minerals were 3 to 4 pct of total weight. Batch flotation experiments were made with 500-g samples of ore, each sample wet-ground to 90 pct passing 200 mesh. The finely ground ore was floated in a Fagergren batch cell at 25 pct solids. The natural pH of the Nevada ore was 8.9 and of the Korean ore, 8.5. The D, RU, K, N, and S-35 sodium silicates were obtained in colloidal dispersions with varying amounts of water. The most alkaline, Metso, was in dry powdered form. For convenience in addition, 5 pct solutions by weight were prepared from each of the silicates, on the basis of dry sodium silicate dissolved in the correct amount of distilled water. Chemical analyses of the various silicates are given in Table I, together with the pH of the 5 pct solutions. A preliminary bulk sulfide float was made with secondary butyl xanthate as the collector and pine oil as the frother. The WO] analysis of the sulfide concentrate was nearly 1 pct for the Korean ore and about 0.1 pct for the Nevada ore. The tungsten contained in the sulfide concentrate constituted about 3 pct of the total tungsten in each ore. No effort was made to recover these tungsten values. The scheelite was floated with oleic acid. Adjustments in pH were made with sulfuric acid or sodium carbonate. A 1 pct solution of 85 pct Aerosol OT was sprayed on the froth and sides of the cell during the scheelite float to aid in dispersing the minerals and to decrease the entrapment of gangue particles. Six tests were planned for each of the six types of silicate in which concentrations of 1, 2, and 4 1b of silicate per ton of dry ore were investigated at both 6.5 and 10 pH. All tests were made at room temperature. The performance of each silicate was judged from the grade and recovery of WO, in the scheelite rougher concentrate. Tungsten recovery was calculated on the basis of the scheelite remaining in the ore after the preliminary sulfide float. Testing of each silicate at three levels of concentration and two levels of pH required 36 tests with each scheelite ore. Variance analyses were performed on the concentrate grades and recoveries to determine whether or not the type of sodium silicate, the concentration of sodium silicate, or the pH significantly affected recovery or grade. Results Concentrate Grade: A variance analysis of the concentrate grades for the Korean ore showed that concentration of the silicate and pH of the ore pulp were major factors in producing a high grade concentrate. Also, the silica- to-so da ratio was important as an interaction with pH. The concentrate grade vs silica-to-soda ratio is plotted in Fig. 1. The curves show that the concentrate grade improved with an increase in concentration of sodium silicate and also

Jan 1, 1959

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By R. L. Templin

The increasing use of aluminum and its alloys in commercial fields tias demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure alunlinum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. Comparison oF Cutting Tools Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30" to 50°, making the total angle of the cutting edge of the tool from 35' to 55". A side

By R. M. Hardgrove

PULVERIZED coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the difficulties incident to the burning of coal. In a cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverized in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. PROCESS OF BURNING CEMENT CLINKERS The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output. This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,1 in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. WET VS. DRY PLANTS The study presented here covers 88 plants, of which 41 are wet and 47 dry. Of

Jan 1, 1941

By M. E. de Morton

Recovery and early recrystallization of heavily deformed, 99.98 pct Cr was investigated by studying metallographic structure. X-ray line sharpening, electrical resistivity, plastic properties, internal friction, and shear modulus. Appreciable recovery of resistivity, internal friction, and shear modulus together with some hardening and relief of internal strains occurred before the visible growth of a textured substructure above 350°C (recrystallization in situ). The complex behavior of shear modulus, internal friction, and its strain amplitude dependence during annealing are discussed qualitatively in terms of the relative mobility of dislocations. BY plastically deforming fully recrystallized 99.98 pct Cr above the brittle to ductile transition temperature, at -350°C. as in wire drawing, chromium can be made very ductile at room temperature. However, this ductility is lost on annealing at high temperatures when recrystallization takes place.' The present investigation was made to determine the general pattern of the changes in a number of physical and mechanical properties during recovery and recrystallization of heavily deformed chromium as part of an effort to elucidate the reasons for lack of ductility in the fully recrystallized condition. PREPARATION OF MATERIAL Wire specimens 0.027 in. in diam were prepared from arc-melted, electrolytic chromium by extruding, hot swaging and finally wire drawing at 300" to 350°C, i.e. above the brittle-to-ductile transition temperature. The total reduction in area of the wire was 98 pct and the last 3 pct of reduction was made at 100" to 150°C before cooling to room temperature. The impurity content of the material is shown in Table I. Internal friction and modulus measurements were made on a single specimen after annealing in situ at successively higher temperatures. For all other measurements, a fresh specimen was used for each temperature and annealing of these specimens was done in evacuated (0.001 mm Hg) and sealed silica tubes for 1 hr at the various temperatures up to 700°C. EXPERIMENTAL METHODS AND RESULTS The occurrence of a. transition in some physical properties of chromium at - 40°C2 imposed limitations on the temperature region where some of the measurements could be made. The reason for this transition in chromium is at present unknown but is probably associated with an antiferromagnetic state observed below - 40°C.* Heavy deformation produces an anomalous decrease in resistivity when measured at temperatures below -40°C4 though a normal increase is observed above this temperature. On the other hand internal friction in heavily deformed chromium5 over the temperature range 40" to 50°C is invariant with temperature. Above and below this range internal friction is strongly temperature dependent, increasing with increasing temperature. A temperature in this range was therefore convenient for both resistivity and internal friction measurements and for consistency the measurements of the mechanical properties were also made at about this temperature. No structural change has, however, been observed in careful X-ray measurements6 between -195" and 50°C, i.e. departure from cubic symmetry was not greater than 3:10,000; X-ray line sharpening measurements were therefore more conveniently made at room temperature.

Jan 1, 1962

By C. G. Black

THE purpose of this paper is to present data obtained from an investi-gation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investiga-tion has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability 'of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose in mind of perfecting the method now tentative to show the true conditions and of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions.

Jan 1, 1936

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

At very low concentrations, carbon dissolves interstitially in molybdenum resulting in a linear expansion of lattice parameter with increase of carbon in solid solution. Geometrical consideration of the relative size of carbon atom to size of interstice approximately predicts the observed volume expansion. THE element carbon, occurring in molybdenum, either as an unavoidable impurity, or purposely added, markedly affects the mechanical properties of molybdenum. Several investigators1-" have noted the occurrence of molybdenum carbide at the grain boundaries of cast molybdenum, and Fischer and Rengstorff' have shown that this intergranular constituent can induce intergranular brittleness. The appreciable change, with temperature, of the solid solubility of carbon in molybdenum, found by Few and Manning," suggests other important effects upon mechanical properties. Finally the relative atom diameters of carbon and molybdenum (the ratio of atom diameters is 0.59) are indicative, by analogy with iron (ratio of carbon atom diameter to iron atom diameter is 0.65), of a possible interstitial solid solution. If carbon dissolves intersti-tially in molybdenum, anelastic effects and age-hardening effects, similar to those observed in other body-centered cubic metals, could be expected. However, from the work of Sykes, Van Horn, and Tucker," it might be inferred that carbon forms only a substitutional solid solution with molybdenum. These considerations made it desirable to study the effect of carbon on the lattice parameter of molybdenum in greater detail than heretofore. All heat treating was done in a high temperature furnace7 built specifically for heat treatment of molybdenum. The temperatures and times of heat treatment were determined from the a solubility limit for the Mo-C system." These heat treatments were carried out in argon which was purified with respect to N, and H.!0." Purification of the argon was accomplished by passing the argon over hot (750°C) titanium and then through a magnesium perchlorate drying tower. As many as six samples were run concurrently and quenched at different times without interrupting the furnace cycle. Both the purity of the furnace atmosphere and ability to quench samples from any temperature up to 4000 °F were of prime importance in the successful heat treatment of samples for the lattice parameter investigation. Carbon Analysis The Leco Combustion apparatus was used for carbon analysis. This apparatus is capable of an accuracy of & 0.003 pct for a 1 g sample in the range below 0.10 pct. However, it is felt the degree of accuracy is somewhat better than this limit in view of the consistency evident by cross checking a number of determinations. The Battelle Analytical Laboratory consistently reported check results to within k 0.001 pct C. X-ray Measurements The molybdenum wire specimens (20 mils) were carefully filed down to about 12 mils and then etched with nitric acid to 8 mils. Carbon analyses were made on specimens before reduction in size; however, since there was no evidence of surface carburization, it is probable that the carbon was uniformly distributed throughout the sample. The resultant specimens were strain free and small enough to minimize the error in the lattice parameter determinations due to X-ray absorption. Diffraction patterns were obtained with a Debye-Scherrer powder camera 114.59 mm in diam utilizing the Straumanis type asymmetrical film mounting. Nickel-filtered copper. Ka radiation and zirconium-filtered molybdenum Ka radiation were used. Line positions on the film were measured with a traveling microscope equipped with a vernier scale permitting measurement to 0.001 cm. The average of five readings was used to determine the position of each line. The lattice parameter for each specimen was determined from the data by the extrapolation method of Bradley and Jay, Y.e., the intercept at 90" of the straight line obtained by plotting the apparent lat-

Jan 1, 1953

By W. W. Anderson, D. G. Girton

The photoluminescence of Pr, Nd, Ho, Er, Tm, and Yb in CdS, and Ho, Er, Tm, and Yb in ZnSe has been observed from crystals Prepared by diffusion using rare earth metals and an excess chalcogen pressure. For a given temperature, time, and chalcogen pressure the spectral characteristics were very reproducible from run to run, and the emission intensity for Nd, Er, and Yb in CdS was as high or higher than the best vapor phase doped crystals we have grown. For a few rare earths it was found that certain conditions of diffusion tend to yield optimum rare earth emission intensity with respect to the background lattice emission. Photoluminescence measwements of Yb in CdS as a function of depth gave a profile which was neither a Gaussian nor complementary error function. Part of the profile appears to arise from a fast component of the diffusion and the other part from a slow diffusing component. At 960°C and 33 atm S pressure, a com -plimentary error function approximation of the slow diffusing component gave a diffusion coefficient of D = 1.3 x 10-9 sq cm per sec. MOST of the studies of emission from rare earth ions in II-VI compounds have been reported on crystals doped during growth,1,2 although Kingsley and Aven prepared ZnSe:Er by diffusion for paramagnetic resonance and fluorescence studies. Pappalardo and Dietz prepared CdS:Yb by diffusion, but they made optical absorption measurements., We know of no study on the properties of rare earth diffusion in the II-VI compounds. To date we have diffused Pr, Nd, Ho, Er, Tm, and Yb into CdS, and Ho, Er, Tm, and Yb into ZnSe and observed the rare earth emission spectra. For a given temperature and chalcogen pressure, the emission characteristics are very reproducible from run to run and for Yb, Nd, and Er in CdS, as good as the best crystals we had prepared by doping during vapor phase growth.2 The emission of Pr, Ho, and Tm has been observed in CdS prepared by diffusion for the first time. Previous attempts2 to prepare these later three materials by vapor phase growth were unsuccessful. The problem of obtaining reproducible characteristics in II-VI semiconductor compound work is well known.5 Not only is it difficult to reproduce results from one laboratory to another but it is sometimes difficult to reproduce results from one growth run to another under ostensibly identical conditions within one laboratory. This situation has been particularly bothersome in research on the luminescence of rare earth activated ZnS1 and Cds2. Crystals from one vapor phase growth run would show very strong rare earth line emission while crystals from a nearly identical run would show no rare earth emission. It was also observed on occasion that the intensity of the rare earth emission was not constant over the entire volume of a single crystal. MATERIAL PREPARATION AND INSTRUMENTATION Vapor phase grown boules of CdS were supplied by Dow Corning. This material was characterized by a free electron concentration of n - 3.5 x 1015 cm-3 and Hall mobility of 350 sq cm per v sec at room temperature. There were microscopic voids and decorated precipitates in some samples. The precipitates annealed out at diffusion temperatures but the voids remained. Single crystal rectangular samples of mm dimensions were sawed from the boules. The ZnSe was polycrystalline, UHP grade from Eagle-Picher. Poly-crystalline samples were sawed from the ingots. The samples were lapped, polished on one side, etched in a solution of 0.5 M K2Cr2O7 in 16 N H2SO4, and thoroughly washed in distilled water. A sample, excess sulfur (or selenium), and 5 mg of rare earth metal (turnings) were sealed in a 3.6 cm3 quartz ampoule at about 2 X 10-5 torr. The high chalcogen pressure used (1 to 30 atm) prevented thermal etching of the crystals and affected the diffusivity and solubility of the rare earth ions in the crystal lattice. For meaningful or reproducible results, it is thus necessary to specify the vapor pressure at which the diffusion was carried out. It is assumed that a negligible amount of the chalcogen was used in the formation of rare earth sulfides or selenides Our sulfur vapor pressure calculations are based on data assuming S2, S6, and S, molecules only in which case the equilibrium constants are given by6 where the pressures are expressed in torr. Selenium vapor consists of a mixture of Se2, Se4, Se6, and Se6 molecules. The selenium vapor pressure was calculated using equilibrium constants given by The status of the rare earth source during diffusion is unknown, i.e., the partial pressures of the rare earth metal and of the rare earth chalcogenides has not been determined. All emission spectra were recorded at 77°K on a Perkin-Elmer model 98-G spectrometer using a 640 line per mm grating. No correction was made for the spectrometer and detector spectral sensitivity. Excitation was by means of an XBO 1600 w xenon arc

Jan 1, 1970

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965