Search Documents

By W. A. McCurdy, Joseph W. Leonard, T. S. Spicer

INTRODUCTION by T. S. SPICER and J. W. LEONARD Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is process design, operation and maintenance to produce an acceptable product which can be sold at the greatest possible profit. Because of these interests, attention to the unrealized potential value of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of both the product as well as the tributary coal flow moving through a modem coal preparation plant. Thus, coal types having similar physical and chemical properties tend to become increasingly concentrated according to size, specific gravity and/or surface chemistry. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches which are sandwiched together in layers and which visually differ from each other by physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, six percentage points of dry volatile matter and 10 percentage points of total sulfur.1 Similar wide variations exist for calorific value, seam moisture content and undoubtedly, for any other conceivable coal test parameter which might be used for comparative purposes. These observations all point to the long established fact that coal is not homogeneous as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance. Since both coal and associated minerals entering a preparation plant are highly heterogeneous, a multi-product potential beginning with certain flotation cell concentrates and ending with plant refuse may exist. Such a potential can and to a limited extent is achieved at some operations by drawing off coal according to size, specific gravity and/or surface chemistry differences from individual coal cleaning processes. Such a sequenced draw-off of coal of increasing ash increments could yield, among other products, chemical coals, coking coals, coals for pulverized fuel boilers, cyclone boiler coals, coals for cement plants, limestone, shale and clay. Basis for Coal Evaluation and Selection Despite the known heterogeneity of coal, the final analysis of a given coal product is customarily reported as a single average since coal has always

Jan 1, 1968

By A. T. English

X-ray dif action techniques were used to investigate ordering and domain coalescence for the B2 (CsC1) superlattice in this alloy. Essentially complete disorder is obtainable by drastic quenching. isothertmal ordering occurs very rapidly at temperatures between 565° and 680°C, only a few seconds being required for development of substantial long-range order. A very fine antiphase dormain structure, found in samples annealed for short times, undergoes coalescence with further annealing. Domain "size" is found proportional to (t)1/2 . This Yate law can be derived by adapting the formalism of Hillert's analysis 01- metallurgical grain growth. For this Purpose the material is descvibed in terms of a "Swiss-cheese " structure, consisting of two multiply connected, mutually intertwined domain volumes. The observed activation enevgy for coalescence, 70 kcal per g-atom, agrees with an estit~lated value ,for volume diffusion in disordered rrzaterial. It is suggesled that the experimental value vejlects the substantially disordered environment of mobile vacancies located in the moving antiphase domain boundary. The alloy Fe-Co-2V is bcc below about 900'C and orders into a B2 (CsC1) superlattice below about 730c It has important applications in magnetic components, including many requiring extensive cold rolling.* example, Marcinkowski and Brown6 observed a re1atively small as-quenched domain size of about 250Å in B2 Fe3A1. Since there appear to be no published data on domain coalescence in B2 alloys, this process was studied in detail. MATERIALS AND EXPERIMENTAL TECHNIQUES A commercial high-purity alloy, nominally 49 Fe-49Co-2V, was obtained from the Arnold Engineering Co. in the form of cold-rolled sheet 0.004 in. thick. Samples were annealed for 1 hr at 800°C in dry H2 to produce disorder and quenched into iced brine. They were then annealed in a nitrate-nitrite salt bath for various times at temperatures between 525° and 625°C. Estimates of the LRO parameter S and the APD size D were made using established X-ray diffraction techniques. Superlattice peaks are best observed using CoKa radiation, for which the value of (fFe-fCo) is maximized. Peak-to-background intensity ratio was improved by filtering CoKß from the incident beam to eliminate sample fluorescence, and by using a pulse-height analyzer. The LRO parameter S was computed from the ratio of integrated intensities I 100/I 200- Owing presumably to systematic errors associated with the presence of crystallographic texture and X-ray extinction, only rough agreement was obtained between experimental and theoretical (absolute) intensity ratios. For this reason certain experimental refinements (e.g., use of balanced filters) were considered superfluous and were omitted. Emphasis was placed on maximizing intensity in order to reduce the time taken to accurately determine the contour of the very small (loo), peak. This was done by point counting 105 counts at appropriate intervals. Background intensity averaged about 1200 cps.

Jan 1, 1967

By W. L. Phillips

Stress-strain curves were obtained for single crystals of 70 pct Ag-30 pct Zn tested in tension and shear. Samples tested in tension and shear had comparable resolved shear stresses and stress-strain curves. The {111} <110> slip system was observed. It zoas found that the9.e is a barrier to slip in both latent close -packed directions and that the magnitude of these barriers is proportional to prior strain during easy glide. It was observed that cross-slip in tension and shear was most frequent in crystals with an initial orientation near <100> "Oershoot" zoas observed in tension. The amount of this "overshoot" was independent of initial orientation. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of easy glide which is characterized by a linear stress-strain curve and a low coefficient, d/dy, of work hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In fcc metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close packed planes, is the existence of latent slip planes in the fcc crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.ls Several theories have been proposed to explain the linear hardening and parabolic stages of the stress -strain curve.6"10 The easy-glide region is the least understood of the three stages. The stress-strain characteristics of Cu-Zn, which shows a long easy-glide region, have been extensively investigated."-" In light of recent ideas on dislocations, cross-slip, effect of solute atoms, and stacking fault energy, it was felt that the certain features of this earlier work might be compared with another alloy, Ag-30 pct Zn, which also exhibits a long easy-glide region. Tension and shear stress at room temperatures were employed. The results obtained, together with some interpretation of the observations, are described below. EXPERIMENTAL PROCEDURE The silver and zinc used for mixing the alloys were 99.99 pct pure. The two components were weighed to within 0.1 pct of the weights required fo the alloy composition. They were then placed in a closed graphite mold and the mold and contents were heated in 100°C stages from 500&apos; to 900°C with sufficient time and vigorous agitation at each stage provided to dissolve the silver. The crucible was then heated to 1150°C and agitated violently before being quenched in oil. The resulting alloy rod was machined free of sur face defects and then placed in a graphite mold designed for growing single crystals. The graphite mold was closed with a graphite plug and was encased in a pyrex glass tube which was connected to a vacuum system. The tube and mold assembly were placed in a furnace; the tube was evacuated and the furnace was rapidly heated to a temperature sufficient for fusing and sealing the glass. The glass-encased evacuated mold and contents were then lowered through a vertical furnace. The top section of the furnace was held at 100 °C above the melting point of the alloy. The lowering rate was 1.5 in. per hr. The tension specimens were 1/4 in. diam; the shear specimens were 1/2 in. diam. These specimens were then removed from the mold, etched, and chemically polished with hot (60°C) Chase etch reagent (Crz03-4.0 g, NH4C1-7.5 g, NHOs-150 cc, HzS04-52 cc, and Hz0 to make 1 liter). In preparation for tensile testing, the specimens were carefully machined to a diameter of about 0.200 in. to permit a gage length of 6 in., annealed for 16 hr at 800&apos; to reduce coring, and then cleaned and polished. A modified Bausch-type shear apparatus which has been described previously18 were employed. The gage length was 1/8 in. This shear apparatus was placed in an Instron tensile testing machine. EXPERIMENTAL RESULTS A) Tension. Several specimens were extended at room temperature to determine the effect of initial orientation on the stress-strain curves of Ag-30 pct Zn. The initial orientation and the resolved shear stress supported by the active slip system at various total strains are plotted in Fig. 1. The critical resolved shear stress, t,, initial rate of work hardening, d/dy, and length of the easy-glide region are independent of orientation. The arrival at the symmetry line is shown by an arrow in Fig. 1. During the easy-glide region of the stress-strain

Jan 1, 1963

By H. Hooykaas

A few years ago Marsal published a method of predicting oil recovery as a function of time for an edge-water-drive reservoir with several rows of wells.&apos; The method is based solely on oil- and water-production data obtained during a short period for the first row of wells and the gross productions (past and future) of all wells. This paper presents a streamlined version of the original publication and experimental evidence showing the reliability of this version. For this purpose scaled experirnents were performed in a large model (750 X 500 X 23 cm, 24.4 ft X 16.2 ft X 8.9 in.) in which edge-water-drive reservoirs with three rows of production wells were simulated. From the results of the experiments it is concluded that the method gives a fairly accurate prediction of the future production behavior of the reservoir and enables us to select the most profitable production plan. Results obtained with the method were always slightly conservative. INTRODUCTION The calculation method developed by Marsal aims at forecasting future reservoir behavior.&apos; It can be applied to floods in which a number of down-dip wells are rapidly going to water. Essentially it is a method for predicting the future behavior of the up-structure wells on the basis of the observed behavior of the down-structure wells. As such, the method is especially useful for predicting behavior of edge-water drives toward several rows of wells. The requirement to be met for justifying the approach is identity of production mechanism in all regions of the reservoir. The attraction of the method then lies in the fact that it applies even when we have no complete description of the prevailing production mechanism. The original publication was in the German language and for this reason, perhaps, did not attract widespread attention. In our opinion it deserves to do so because it does offer in a simple way results which are in fair agreement with observed data. The aim of the present paper is to bring the method to the attention of a wider audience. The method in its most simplified form is reviewed and experimental data in support of it are presented. PRINCIPLES To show Marsal&apos;s principle. we will first write the continuity equation for very simple conditions, linear flow (in the positive x-direction) in an incompressible porous body [cross-section A(x), porosity +(x)], saturated with incompressible fluids (oil saturation S). When the oil in this formation is displaced by water, injected at x = 0 (inlet face), we get where q(t) is the total gross displacement rate and f the fractional oil flow. The equation can be solved if we make the assumptions: (1 ) that the fractional oil flow (f) is a univalent function of saturation (S); and (2) that the function is the same throughout the porous medium. Then: f = f(S) Solving this equation with the method of characteristics, we obtain

Jan 1, 1966

By Eugene S. Machlin

A classical theory of solid solutions involving neavest-nergkbor intevactions with both central and linked-central forces between atoms has been developed. It has been found that the theory, where it can be checked quantitatively, is in ageement with experiment. The theory encompasses a description of many diverse pkenomena, such as antiphase shift structures, size effect, relative stabilities of various solutions, lattice para,neters, and order-disorder transitions. In particulav. a quantitative prediction not involving adjustable pavameters is made concevning the deviation of the Au-Cu interatonlic distance in long-range ordered (Ll,) Cu-Au I fronl the average distance based on the distances in pure gold and copper. This prediction, which is in agreement with expel-intent, has not been encompassed by any preuious theory. The theory of order-disorder is fragmentary. That is, no one theory exists that can explain the variety of qualitative phenomena observed. Further, many theories are not in good quantitative agreement with experiment. This subject has been reviewed by Muto and Takagi, Tuttman, and Oriani.3 There exists no doubt that the quasi-chemical approximation is not a complete description and that the inclusion of strain energy using macroscopic elasticity theory concepts leads to results in disagreement with experimenL4 The observation of antiphase domains and ordering systems such as Cu-Pt has led to Brillouin zone treat-ment of the order-disorder transition as opposed to the classical Ising model. The objective of this paper is to demonstrate that it is possible to develop a pairwise approximation model that can explain many of the observed order-disorder phenomena that have puzzled investigators in the past. This theory is based upon an empirical model due to ergmman&apos; for the elastic constants of metals. This model is generalized for multicomponent systems. As will be shown, the theory yields a short-range ordering energy for the disordered solution which differs from the ordering energy calculated from the differences in energy of disordered and long-range ordered solutions. It will be demonstrated that there is no necessary correlation between heats of formation and the tendency to order or between size effect and the tendency to order. Also, the existence of antiphase domains and iso-short-range-order systems that form superlattices (Cu-Pt) is predicted on the basis of the theory. Further, the relative stability of competing superlattices is calculable from the theory. If single-crystal elastic-moduli data are available for the pure components and one superlattice then there exists but one adjustable parameter in the calculation of lattice parameters for both the disordered and ordered solid solutions. In one special case, no adjustable parameters are required and a quantitative prediction is made. For the calculation of energies and partial order, there exists but one additional adjustable parameter, the pair-exchange energy V used in the quasi-chemical approximation (or the Ising model.) However, in these calculations, much more precise values are required for the single-crystal elastic moduli than available if the quantitative uncertainties in the predicted values of the energies are to be sufficiently small. THEORY ~er~man&apos; has developed a model with which he was able to obtain fair agreement with experiment for the relations between the elastic constants for metals. This model which we shall call Bergman&apos;s model is a linear combination of his models I and 11. In effect, Bergman, in this model, considers that each interatomic distortion is composed of two components: a classical central force distortion with an associated central force constant and what we shall call a linked-central force distortion with an associated linked central-force constant. The linked-central force distortion component obeys the constraint that the sum of such distortions over all the bonds equals zero. No constraint is imposed on the classical central force distortion component. Bergman&apos; derives the constraint on the linked-central force distortion on the basis of application of Pauling&apos;s relation between bond distortion and bond number to metals.ga This assumption is not logically necessary, however, and the Bergman model may be taken as a mathematical model for elastic constants, e.g., a purely empirical model without a physical basis. In the present work, the method of Bergman has been applied to two-component systems (solid solutions). In place of an external strain—which would allow a calculation of the elastic constants for the two-component system—it is considered that internal interatomic distortions exist as a consequence of having three potentially unequal distortion-free interatomic distances and but one "average" interatomic distance. It is assumed that the distortion-free interatomic distances between atoms of the same element are those found in the pure element having the same undistorted crystal structure as the solid solution. The distortion-free interatomic distance between unlike atoms is in general not measurable except in the probably nonexistent

Jan 1, 1967

By Wayne P. Myers

Electricity, as normally thought of by a layman&apos;s definition, is a manmade force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man&apos;s safety, are rigidly enforced by the U.S. Bureau of Mines, as well as the various state departments of mines. BACKGROUND Until recent years most underground coal mines used direct current exclusively for all movable and for some stationary equipment. Exceptions were for permanent pumps, tipple, fan, and outside buildings where alternating current was normally employed. However, over 60 years ago there were mines with dual systems. Alternating current was used for cutting machines, drills, and pumps, direct current for locomotives. There were no other machines as these were hand-loading mines. Later, during early mechanization in the 1920s, alternating current was also applied to loading machines at some mines. Use of dual electric systems then declined until fairly recently when

Jan 1, 1973

By Joseph D. McClung, L. G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups, that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mrn) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh ( <0.60 mm) ; in fluidized bed uses, the coal is typically < in. ( < 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1-2 1/2 in. (25-63 mm). Coal preparation plants typically work with a coarse size fraction of 6x1 1/4 in. (15Ox32mm). It seems probable that the next decades will see much wider application of coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is inti-

Jan 1, 1979

By W. J. Skewes, C. T. Holland

Properly constructed stopes are necessary underground for proper ventilation and safe, healthful working conditions. Mining companies are concerned with providing the best possible stoppings at an economic cost. It is important to consider 1) proper materials, 2) construction that ensures maximum performance from the material used, and 3) keeping costs within reasonable limits for the unit operation—stopping—involved. The authors investigated all aspects of the problem and have attempted to layout a study program to provide information on all phases. Mining companies every year purchase huge amounts of material for the construction of ventilation stoppings. This material by the time it is in place in the stoppings will cost the company many thousands of dollars. In addition and more importantly these stoppings are supposed to confine air travel along certain well defined paths into areas where it is needed to provide safe and healthful atmospheres for workmen. The cost of forcing this air through the mine is large and in general increases as the total quantity increases. Consequently, if the stoppings leak, increased cost results and in addition unsatisfactory ventilation may prevail in the mine. Therefore, it is essentia1 to provide the best possible stoppings at an economic cost. When attempting to provide the best stoppings possible at an economic cost, three aspects of the problem must be considered. These are 1) getting the most suitable material for stopping constructions, 2) constructing the stopping so as to get the best performance from the material used, and 3) keeping the cost of stopping construction to a minimum for a suitable stopping. This investigation is concerned with all phases of the problem and has attempted to lay out a study to provide information on all of them. In order to develop information on the best stopping material available it seemed wise, after con- sidering the job a stopping must do, to investigate the following aspects of material used for stoppings: 1) strength in compression, 2) compressibility or yield under load, 3) porosity, and 4) permeability. To provide information on the best manner of construction the following aspects of air leakage through the stopping were investigated: 1) when the stopping is built of dry stacked materials—i.e., the joints are not mortar-laid (See Fig. 1); 2) when the stopping is built of dry stacked material and then plastered on one side (see Fig. 2); 3) when the

Jan 1, 1961

By Michael Tenenbaum, C. C. Brown

Numerous investigatiolls have been carried out to determine the total oxygen present in the basic open-hearth bath and the results of these studies have clearly defined the factors controlling the bath oxidation during the period prior to deoxidation. On the other hand, very little is known concerning any changes in total oxygen content that may occur during deoxidation, tapping and teeming. The need for such additional data is continually becoming more apparent, since there is no strict technical basis for selecting any particular deoxidation practice. Many steels are made for the same purposes and to the same chemical analyses by widely differing practices. Apparently, each practice is satisfactory. However, it would be desirable to establish more definitely the effects and relative merits of the individual practices. Such information could be used to give a definite foundation for evaluating various types of deoxidation. In order to approach this problem, a study was made of the changes effected in the total oxygen content of several grades of steel by representative open-hearth deoxidation practices. To carry out such studies, it was necessary that a reliable testing procedure for determining the oxygen content of the steel bath and the ingot mold be established. Before entering on any extensive testing program, consideration was given to the available methods of obtaining steel samples and analyzing for oxygen. Testing Procedures It has been shown5-9 that in solidified steel oxygen may ekist in combination with iron, manganese, silicon, aluminum, titanium, chromium and carbon, depending upon the amount of these elements in the sample. In molten steel, however, there has been no direct distinction of the various oxides. Accordingly, the total active oxygen in the molten steel bath is designated by the symbol 0. During deoxidation, various oxides may be present either in solution in the molten steel or as solid or liquid inclusions. Any sample taken from the molten steel for oxygen analysis will include both the dissolved and the mechanically included oxygen. Similarly, samples of the solid steel product will also include the two forms of Oxygen&apos; Methods of Samplirzg the Molten Steel Bath In order to obtain a true oxygen analysis from liquid steel, this element must be completely retained in the solidified sample. Several methods have been proposed whereby this stabilization can be effected. As early as 1915, Kichlinelo proposed a method for testing molten steel, in which the oxygen combined with some added aluminum. The concentration of the resultant aluminum oxide was determined by chemical analysis. This method was

Jan 1, 1945

By D. M. Wyslouzil

Standard testing methods are described that are presently used for the selection of grinding equipment. Correlation between laboratory batch grinding tests and pilot plant continuous tests are established by means of particle size distributions and flotation results. Conventional and autogenous grinding circuits are discussed showing the relationships of the controllable circuit parameters.

Jan 1, 1982

By H. G. Papacharalambous, S. C. Sun

Experimental results indicate that wet cyclones could be effectively used for the preliminary classification of the tested synthetic abrasive materials, thus supplementing the currently used sedimentation method. An empirical formula is also proposed on the basis of the test data to calculate the particle size of separation. One of the basic operations in the abrasive industry is the classification of the crushed and ground materials into different sized products. The relatively coarse grains, plus 325 mesh, are commonly sized by dry screening with satisfactory results. On the other hand, however, the currently used grading tank, for classifying grains finer than 325 mesh, is intermittent. Consequently, it is difficult to operate efficiently and keep pace with erratic market requirements. Little success was made in an attempt to substitute air settling and continuous hydraulic settling for the grading tank, because size specifications1 for abrasive powders are very stringent and difficult to meet. Finally, a wet cyclone was chosen for experimentation. Even though wet cyclones have not been extensively used in the classification of abrasives; however, their performance as a classifier has been verified by Driessen2,4 on coal, McCarrel5 with manganese, and Herkenhoff6,7 on iron ore. Experimental work on silicon carbide, boron carbide, and fused alumina has shown that the cyclone

Jan 1, 1963

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter&apos;s tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.&apos; The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"&apos;, an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967

By Steve H. Carpenter, Henry E. Otto

The explosive welding of metals is dependent upon the production of a jetting action caused by the collapsing of one metal plate against another. Successful welds are generally accomplished if the yield strength of the metals is in the range of 10,000 to 90,000 psi and the sonic velocity of the metal is greater than the detonation velocity of the explosive if direct contact explosive is being used.&apos; Should the detonation velocity exceed the velocity of sound in the metal it may still be possible to obtain the jetting action and a good weld. However, in most cases where a high detonation velocity is used complications arise because of reflected shock waves which tear the bond apart as fast as it is put together.&apos; Explosive welding of lead presents several problems since its yield strength and sound velocity are very low. Various values have been published3-5 for the velocity of sound in lead ranging from 2000~ to 23004 m per sec. Most of the high-order explosives have detonation velocities on the order of 6000 to 8000 m per sec, which precludes their use. The dynamites have a lower detonation velocity of around 2800 m per sec which is still somewhat too high. Lower-order explosives such as ammonium nitrate (1070 m per sec) must be used to weld lead in the as-received condition if the explosives are used in direct contact. Rather than use low-order explo&apos;sives it was decided to alter the sonic velocity of the lead. The sonic velocity is directly related to the modulus of the material according to the following expression: Fig 1—Interface of explosive weld of lead to steel. Lead is on top As-polished Magnification 75 times as well as the yield strength. Bolling et al. 6 show that the shear modulus of lead single crystals increases from about 0.72 X1011 dynes per sq cm at 300°K to about 0.98 X1011 dynes per sq cm at 0°K, an increase of approximately 3 5 pct. This gives an increase in the sonic velocity of around 700 m per sec. Hence, the sonic velocity of lead at cryogenic temperatures is approximately equivalent to the detonation velocity of the low-order dynamites. We have obtained high-quality lead to steel explosive welds using a 40 pct dynamite in direct contact with the lead. Prior to detonation the lead was chilled with liquid nitrogen (78°K) to increase the strength and sonic velocity. Welds were made while the lead was cold. Specimen sizes were 3 by 6 in. A preset angle of 5 deg with a 0.10-in. standoff at the base was the geometrical setup used. The amount of explosive used for optimum welding of an 1/8 -in. -thick lead sheet to a steel plate was found to be 7 g per sq in. A PETN sheet explosive line wave generator was used to insure a linear detonation front through the dynamite. A photomicrograph of a lead-steel weld is shown in Fig. 1. The typical wave effect that constitutes a good explosive weld is present. When tested in shear, the weld failed in the lead, indicating that the bond is stronger than the lead base metal. Higher-order explosives were also tried without success. We believe this indicates the importance of matching the detonation velocity and the sonic velocity for successful explosive welding. Note Added in Proof. High quality explosive welds of lead to steel have recently been obtained at ambient temperature using a low velocity (1000 M per sec) free running dynamite. The weld interface obtained is comparable to Fig. 1. &apos;S. H. Carpenter, R. H. Wittman, and R. J. Carlson: Proceedings of the First International Conference of the Center for High Energy Forming, Syracuse University Press, syracu.se, N. Y., in press. &apos;A. HI Holtzman and G. R. Cowan: Welding Risearch. Council Bull., No. 104, April, 1965. &apos;Metals Handbook, 8 ed., p. 1062, Metals Park, Ohlo. &apos;J. M. Walsh, M. H. Rice, R. G. McQueen, and F. L. Yarger: Phys. Rev., 1957, vol. 108, pp. 196-216; &apos;L. V. Al&apos;tshuler, K. K. Krupnikov, B. N. Ledener, V. I. Zuchikhin,

Jan 1, 1968

By J. Larsen-Badse

The resistance to dry sliding abrasion us been measured for some hardened and tempered carbon steels. The wear resistance, defined as the reciprocal of the volume loss per unit sliding distance, is found to vary linearly with the hardness of the abraded surface. The data fit two lines, one, of high slope, for the pure metals and for the annealed steels and another, of smaller slope, for the hardened and tempered carbon steels. A relationship is developed showing the alwasion resistance to be proportional to the hardness of the material and to en, where n is the exponent of work hardening. The values of n and of the hardness FOR most materials a high resistance to abrasion is generally associated with a high value of indentation hardness. Brine11 even used the abrasion resistance as a measure of hardness in an attempt at expanding the hardness range covered by his indentation-hardness test.&apos; When comparing different types of materials there is, however, only a very general relation between abrasion resistance and hardness. Sample brittleness seems to contribute to the deviation from a direct relationship. In general, increased brittle- are those relating to the heavily deformed abraded surface. However, for materials having n constant or varying m a regular manner over a wide range of strailts, the wear resistance will also be a linear function of the bulk hardness of the material. For tempered steels containing a dispersion of cementite in ferrite the increase in wear resistance due to the dispersion is found to be a linear function of the volume fraction of Fe3C and of the reciprocal of the mean free ferrite path. This indicates indirectly that the yielding of this material, when it is already heavily deformed, follows the Orowan criterion. ness leads to decreased abrasion resistance.&apos; When comparing materials in the same group, e.g., the metals, the spread is less. Kruschov found that the abrasion resistance of pure metals and of annealed steels is directly proportional to the hardness of the metal. For hardened and tempered steels he obtained another linear relationship, one of smaller slope and intersecting the line for the pure metals at the location of the data for the annealed steels. He also found that the abrasion resistance of cold-worked metals is independent of the degree of cold working. This shows, as he concluded, that the process of abrasion work hardens the metal in the surface region to a very high degree.

Jan 1, 1967

By Fred A. Anderson, George B. Wallace, Edward J. Slebir

Auburn Dam will be a thin, double-curvature concrete arch dam about 685 ft high. With a crest length of about 4000 ft, it will be the world&apos;s longest single-arch dam. The site is located on the North Fork of the American River about 40 miles northeast of Sacramento, Calif. Construction is scheduled to get under way in 1970. In planning for the design and construction of Auburn Dam (see artist&apos;s conception), the foundation material, with its various discontinuities, is being investigated and the structural characteristics of the rock mass evaluated. The investigation and testing programs will aid in defining the pertinent geologic features and their individual and cumulative influence on the foundation. The work includes geologic surface mapping, surface trenching, core drilling, geophysics, tunneling, excavating shafts and raises, performing in-situ tests, and conducting laboratory tests on core and block samples. Competent amphibolite is the predominant material in the foundation, but significant bodies of chloritic, talcose, and metasedimentary rocks, a strongly developed jointing pattern, faults, and shear zones also affect the deformability of the rock mass. A comprehensive rock mechanics program, closely coordinated with geologic investigations as well as the engineering studies, therefore is required The rock mechanics work is a combination of many analytical studies and experimental investigations. The experimental work includes laboratory tests on core samples from holes drilled for geological studies of the entire foundation and in-situ tests performed in selected areas. The laboratory testing program evaluates the general properties of all important rock types and aids in correlating many of the key structural features encountered within the foundation. To derive maximum benefit from the field tests, they are conducted in materials which represent a

Jan 1, 1970

By F. H. Turan, F. W. Jessen

The gel strength and viscosity of two different suspensions of fractionated montmorillonite clay were measured by using a Stormer viscosimeter and Farm V-G meter. The amount of sodium poly-phosphate (sodium bexametaphosphate, sodium tetraphosphate and sodium acid pyrophosphate) adsorbed by the clay particles was determined. A relationship seems to exist between the amount of polyphosphate adsorbed and the nature of the surface, edge or plate, assumed to be the principal sites for selective adsorption. Reduction in viscosity and gel strength was found to be directly related to the adsorption. Both chemical bonding and physical adsorption seem involved in defloccula-tion Some indication of the axial ratios of particles of .l- to .04-micron average size is possible though study of the adsorption mechanism. INTRODUCTION AND PURPOSE A knowledge of surface areas of clay particles in a suspension and a precise determination of phosphate adsorption should provide a basis for a better understanding of reduction in viscosity and gel strength caused by molecularly dehydrated phosphates. The purpose of this investigation was to study the adsorption of sodium polyphosphates on suspensions of fractionated sodium montmorillonite. Although there is considerable uncertainty regarding details of the structure of montmorillonite, a generally accepted one is that suggested by Hofmann, Endell and wi1m.l The structure shown in Fig. 1 is an idealized one, and Marshall2 has postulated that it is possible for several isomorphous replacements to occur. Thus, aluminum may replace silicon, in which case an exchangeable cation would go along with the aluminum to neutralize what would otherwise be a net negative charge on the structure. There is disagreement among various investigators as to the particle size and shape of montmorillonite clays. Marshall2 reported the following results for the mean lateral dimensions of a Putnam clay (montmorillonite)— 3,730 A° for particles having average diameters ranging from 500 to 1,000 A, and 750 A° for those with an average diameter less than 200 A. The latter particles were estimated at 50A°in thickness, which would correspond to a stack of five unit cell layers. On the other hand, Shaw3 has interpreted micrographs as indicating that particles of montmorillonite ire readilv broken down to the individual cell layers by dispersion in water. Brindley4 and Merings indicate the ultimate particles to be of the order of 300 A° in mean lateral dimension. Van Olphen6 suggested the thickness of particles at four to five unit cell layers. It was suggested also that this number tends to become smaller with increasing dilution. Recently, Kahn and Lewis7 determined the size of sodium montmorillonite particles in aqueous suspension from electro-optical bi-refringence decay curves. The

Organization. Place Date 1915 American Institute of Mining Engineers New York, N. Y. Feb.18-21 National Society for Promotion of Industrial Educa- tion New York, N. Y. Feb. American Institute of Architects.... Washington, D. C. April American Iron and Steel Institute New York, N. I? May New York Electrical Society: New York, N.. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept.9-13 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic City, N. J. Sept.

Jan 2, 1918

By Charles H. Fulton

Experimental work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc-lead ores, since the residue from the distillation IS held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet may be used over again as coke, or as a high ash coke for fuel purposes in power production. Baked briquets are hard and tough and may be handled roughly

Jan 1, 1921

By L. R. Duncan, O. M. Wicken

Magnesium, the eighth most abundant element in the earth&apos;s crust, is found widely distributed in a variety of minerals. Among the more commercially important ones are magnesite (MgCO3), brucite (Mg[OH]2), dolomite (CaMg[C03]2), and the salts magnesium sulfate and chloride often found in natural brines. Among other commercially important magnesium-containing minerals are olivine ([MgFe]2Si04), talc (H2Mg3[Si03]4), and serpentine (H4Mg3Si2O9). These are valuable because of desirable characteristics given them by the magnesium content and its placement in the particular crystal structure. These minerals are the raw materials for a host of products including magnesium metal and several grades of magnesia or magnesia-containing materials for refractories, fluxes, fillers, insulation, cements, decolorants, fertilizers, and chemicals. Considering only those minerals valued for their magnesia or magnesium content, over 85% of the material tonnages are processed to be used as refractories. Dolomite, which is used in enormous tonnages for its physical properties in construction, has an important use as a refractory raw material in its own right and, after calcination, as a precipitant for magnesium hydroxide, which is an intermediate for the production of magnesia or magnesium metal. Magnesia from the reaction of calcined dolomite (or limestone) with seawater or magnesium-containing brines has supplanted much of the production of magnesia from mined magnesite, particularly in the United States. The best known of the minerals directly and widely exploited for magnesia content is magnesite, one of the calcite group of rhombohedral carbonates which includes calcite (CaC03), siderite (FeCO3), and rhodochrosite (MnCO3) among others. The members of this group enter into a wide range of substitutional solid solutions when the positive ions have similar radii. The radii of magnesium and iron ions are within 6% of each other; hence, magnesite and siderite form a complete series of which breunnerite (ferroan magnesite) is a well-known end member. However, the radius of calcium ion is 36% larger than that of magnesium ion, and only limited substitution exists at each end of the MgCO3-CaCO3 series. Dolomite is not a member of the calcite group, but results when calcium and magnesium ions alternate in equal number in an ordered structure among carbonate ions. The result of these relationships is that calcite and dolomite, often found intermixed with magnesite, occur commonly as identifiable crystal entities which can often be separated to a varying degree from the magnesite by various beneficiation techniques. Magnesite, when pure, contains 47.8% MgO and 52.2% CO.. The pure mineral is sometimes, but rarely, found as transparent crystals resembling calcite, but, preponderantly, magnesite contains variable amounts of the carbonates, oxides, and silicates of iron, calcium, manganese, and aluminum. Magnesite may be either crystalline or amorphous (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black with shades of yellow, blue, red, or gray. The color is not a fundamentally significant indicator of purity, but in a given deposit, an experienced person can often roughly grade magnesite by assessing color and crystallinity. The crystalline form of magnesite occurs in

Jan 1, 1983