Search Documents

By H. C. Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions.

Jan 8, 1950

By W. C. Knopf, G. Samsel

For several years International Minerals & Chem-ical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large-scale plants. Natural potassium is composed of three isotopes —K, K and K. Five other isotopes, artificially produced, have been detected. In natural potassium only the K isotope, with a half life of 1.4x10 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes. Barnes and Salley' measured radiation of potassium salts in solution in 1943. Gaudin and Parnell2 first reported the use of solid salts arranged in a vessel surrounding the ß counter in 1948. Later, Scheel used the method to assay potassium content of various crude and finished potash salts. Experimental: Dip-type Geiger-Muller tubes (TGC-5) supplied by Tracerlab Co. were used in all radiation counting measurements. The tube was encompassed by a glass container about M in. larger in diameter than the tube. This container, which served as a sample holder, was closed at the bottom with a rubber stopper to facilitate removing the samples. Samples were not weighed, but about 40 g of sample were needed for each test. Electrical impulses from the tube were counted on either a Tracerlab scaler or a rate meter. To obviate the need for constant attendance, preset features were incorporated into the scalers, so that at a predetermined time or count the units were automatically deactivated. When rate meters were used, counting rates were read directly from instrument or from a recorder used in conjunction with the rate meter. Each tube was calibrated, according to the manufacturer's instructions, to determine the correct operating voltage to insure reproducible results. A linear calibration plot of percent K2O vs counting rate was also obtained for each tube by recording the counting rate plus background count of several standards of different K2O content chemically analyzed by the chloroplatinate method.' These standards were of approximately the same particle size distribution as samples to be assayed. Specific background count caused by cosmic rays and other surrounding radiation was checked periodically by counting a sample of pure NaCl. Fig. 1 is a representative calibration plot. Assays were determined directly from the standard plot or calculated by subtracting the background count from the counting rate, then multiplying by the slope of the line. Chemical assays of the test samples were made by the Sherril method," a flame photometric technique, or the chloroplatinate method. Data: The radiation assay method has been used for three years by International Minerals & Chemical Corp. in the laboratory and in pilot plants processing ores containing potassium. These dry concentration plants process sylvinite and langbeinite ores at Carlsbad, N. M., and feldspar ores at Top-sham, Maine. Sylvinite ore is predominantly a mixture of syl-vite (impure KCl) and halite (impure NaCl). Contaminants include sulfates, such as langbeinite (2MgSO - K2SO4), kieserite (MgSO H2O), poly-halite (MgSO4.K2SO, 2CaSO, . 2H2O), and slimes. Langbeinite ore is predominantly langbeinite and halite with small amounts of sylvite, sulfates other than langbeinite, and slimes. Several variables, in addition to correct calibration and standardization of tubes, were found to be important in obtaining reproducible results. Particle size distribution of standard samples should be

Jan 1, 1959

By Ronald K. Linde

Metastable Ag-Cu solid solutions at two compositions beyond the maximum limits of solubility obtainable by quenching from the solid state were obtained by rapid quenching from the liquid state. The process of transformation of the metastable solid solutions into the equilibrium phases was studied by means of X-ray diffraction intensity measurements and electrical-resistance measurements; metallographic examination was also performed. Results are compared with those for an alloy quenched from the solid state at a composition which exists as a solid solution at elevated temperatures. Activation energies for the trans-formation were computed to be 33,600 * 2500 and 33,100 * 2000 cal per g mole for the 60.1 and 75.0 at. pct Ag;Cu compositions, respectively THE kinetics of precipitation in supersaturated solid solutions obtained by quenching from high temperature has been thoroughly studied in many alloys, and detailed investigations of the early stages of nucleation and subsequent growth of the equilibrium phases have been carried out. All of these studies have been made on alloys quenched from the solid state, however, and it is the purpose of this paper to present some of the results on the kinetics of transformation of metastable solid solutions in Ag-Cu binary alloys whose compositions lie outside of the solid-state limits of solubility. Limits of solubility in the solid state can be increased by rapid quenching from the liquid state. This was first demonstrated by Falkenhagen and Hofmann, who obtained appreciable increases in solubility limits of the elements of the first transition series in aluminum by rapid cooling of liquid alloys through contact with a copper mold maintained at liquid nitrogen temperature.' The same basic idea of cooling a liquid alloy by conduction onto a substrate rather than by convection of a gas or liquid (conventional quenching) has been recently revived and extended to very high rates of cooling by Duwez and his collaborators. The new technique was first applied to Ag-Cu alloys because the existence of a eutectic in this system is not predicted by the Hume-Rothery rules of alloy phase formation. Rapid quenching from the liquid state resulted in metastable solid solutions at all concentrations. The kinetics of decomposition of these metastable solid solutions containing 60.1 at. pct Ag;Cu (eutectic composition) and 75.0 at. pct Ag;Cu is the subject of the present paper. EXPERIMENTAL TECHNIQUES Alloys were made in 10- to 20-g heats using silver of purity 99.99 pet and copper of purity >99.999 pct. Components were weighed accurately to 0.1 mg and melted by induction heating in an alumina crucible under an atmosphere of hydrogen. Weight losses amounted to less than 0.02 ~ct in all cases. Rapid cooling from the liquid state was achieved in an apparatus of the type described by Pietrokowsky. 3 In this technique a freely falling drop of molten alloy is caught between a stationary anvil and a fast moving piston, both anvil and piston being lined with copper. The resulting foils were approximately circular (about 2 cm in diam) and from about 50 to 150 u in thickness, depending on the pressure driving the piston. Metallographic samples were prepared for polishing by edge-mounting foils in Quickmount. The mostef-fective etching procedure was found to be: 10 parts NH4OH (concentrated), 1 part H2O2 (30 pct), 5 parts H2O, swab for 5 to 10 sec. The transformation of the metastable alloys to equilibrium was followed by X-ray diffraction and electrical-resistivity measurements. The peak intensity and the integrated intensity of suitable Bragg reflections of the metastable and stable solid solutions were studied with a Norelco dif-fractometer, using nickel-filtered copper KO radiation. The peaks were step-scanned at intervals of 0.05 deg. Using either a Kelvin bridge or a null circuit with a Leeds and Northrup K-2 potentiometer, the changes in electrical resistance due to phase transformation were measured for specimens cut into strips about 20 mm long and 4 mm wide. All resistivity measurements were carried out at liquid-nitrogen temperature. The isothermal heat treatment was accomplished by sealing the samples in argon-filled aluminum containers with stainless-steel O-rings. Containers were then suspended in wax baths with temperatures in the

Jan 1, 1967

By H. H. Klepfer, M. E. Snyder

UNTIL very recently, the commercial availability of the rare earths as metals has been very limited. Fabrication of mill products from these metals has not been studied in most cases. This note reports the results of the development of fabrication techniques for thulium. Thulium has a melting point of about 1550°C and a hexagonal close-packed crystal structure. It oxidizes in air to give a black oxide (TmzO,). The procedures for producing thin thulium foil were developed on one ingot weighing about 220 g and were subsequently applied in processing about a pound of metal to foil. Several alternates for the various fabrication steps were investigated and will be discussed. The metal fabricated was in the form of commercial chill-cast ingots 1 in. in diam and 2 in. long weighing approximately 220 g. Impurities in the ingots were reported by the vendor to be 4000 ppni tantalum, 2000 ppm calcium, 200 ppm nickel, 100 to 200 ppm iron, 100 ppm europium, and less than 100 ppm copper, lutetium, and ytterbium. In addition to these impurities, several salt-like inclusions as large as l/8 in. in diam were revealed along the center line of the one ingot sectioned. Preliminary tests indicated that small wafers cut from the as-cast ingot would not fabricate readily by rolling. Forging of copper-jacketed wafers was therefore attempted. At 1550"F forging was satisfactory but an apparent reaction of copper with thulium demanded investigation of lower temperatures. Therefore, the remainder of the test ingot was forged at 1450°F—with only minor cracking. All ingots forged were inserted into copper tubes of 1 in. 1D and 0.125-in. wall thickness. The jackets were sealed by flattening the ends of the tubes and welding under helium. Heating time at 1450°F was 30 min. Press forgings of 1/8 in. per pass were used, followed by 10 min reheats. When the ingots had been squared and reduced to 0.250 in. in thickness, the original copper jacket was stripped off and replaced by a new jacket in preparation for hot rolling. Hot rolling at 1450" F without edge cracking was readily accomplished after forging. Excellent results were obtained with 10 pct reductions of thickness followed by 5 to 10 min reheats. After reduction of thickness from 0.250 to 0.100 in. the copper jacket was removed. It was found, in fact, that hot rolling in air was possible. A tenacious black oxide similar to that seen on zirconium was formed during 3 min reheats at 1450°F. Reduction in air to 0.010 in. foil was possible taking 10 pct reductions per pass. The oxide coat formed during hot rolling in air could best be removed by sand blasting and pickling. Common pickling solutions containing polar solvents were found to attack the metal too rapidly and a concentrated nitric-hydrofluoric acid mixture attacked neither the oxide nor the metal. The most satisfactory pickling solution was 52 vol pct concentrated nitric acid-48 vol pct glacial acetic acid. After forging to 0.250 in., vacuum annealing and cold rolling was found to be another satisfactory alternate to hot rolling in copper jackets. After forging. a hardness of Rockwell B76 was found. Annealing in vacuum (2 X l0-5 mm of Hg) for 1 hr at 1200"F did not alter this value. Annealing at 1470"F for 1 hr brought the hardness down to R;]63. With cold rolling (5 pct per pass) the hardness returned to about R,1:76 after 20 pct reduction and edge cracking became noticeable. However, cold rolling to a total of 40 pct reduction in thickness (RI,,83) was possible before edge crack propagation became serious. Good surface finish was obtained, and the metal loss due to oxidation was minimized by cold rolling and vacuum annealing. Using this procedure the yield of 1.25 in. wide by 0.010 in. thick foil from a 1-in. diam ingot was about 40 pct.

Jan 1, 1961

By H. C., Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions. Prior to the war years Inspiration's costs of mining by block-caving methods were comparable to, or even below, the costs of some open-pit operations. By the end of the war these conditions were completely changed. Underground costs had risen steadily for labor and supplies. Difficulty was being experienced in finding competent underground men and underground development was almost hopelessly behind schedule. On the other hand, open-pit costs had been sharply reduced through the development of modern earth-moving machinery and plenty of labor was available for surface work.

Jan 1, 1950

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Table I (Jones, 1973) affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 (Anon., 1967) is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak-type brines, produced mainly for lithium. Market Attributes Some of the important market traits common to industrial minerals used by the chemical industry are listed below. 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. For example, fluorspar from China and Thailand normally goes to Japan, while South African fluorspar can go either to Japan or to the US. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities.

Jan 1, 1983

By Anthony Anable, J. V. N. Dorr

When separate treatment of sand and slime by cyanidation was the rule rather than the exception, as now, and when gravity concentration, rather than flotation, was the accepted method of dressing copper, lead, zinc and other base ores, classification was a separate step in ore treatment. Today, however, the picture is much different. The trend toward all-slime treatment in cyanidation and flotation has made fine closed-circuit grinding essential, and the mechanical classifier is of equal importance with the mill in the preparation of an ore for its treatment. Actually, a mill and classifier are a unit, a variation in either affecting the desired results. In developing this thesis—the mutual interdependence of the rotary mill and the classifier in modern fine-grinding practice—it would be well to consider first the different types of classifiers and mills in use today, their scope and limitations and the factors governing their selection. From such a basis as this a logical approach may be made to modern closed-circuit fine grinding, the evolution of multiple-stage grinding practice, the relation of the classifier to the mill and, finally, the trend to higher and higher circulating sand loads in the mill-classifier circuit. Such data as are germane to the subject will be given to support the thesis advanced. Mechanical Classifiers Theory.—Stokes' law, applicable to the uniform slow motion of a rigid sphere in a viscous fluid of infinite extent, states that the velocity of a particle settling under the influence of gravity is a function of the square of its radius: _ 2 g(ds - de)?2 v =9 S Where V = velocity of particle in cm. per see. g8, acceleration due to gravity d8, density of particle de, density of fluid ? = radius of particle S = viscosity of fluid

Jan 1, 1935

By C. W. Tomlinson

INTRODUCTORY THE analyses which have been made by the writer according to the method described below were made as part of Professor Withey's investigation of the concrete aggregates' of Wisconsin, in the hope of throwing light on the extent and nature of the influence of the mineralogical constitution of aggregates upon the properties of the concrete, and mortar made from them. This method was found most satisfactory after four weeks of experiment and modification. It attains an accuracy quite sufficient for the purpose of the analysis, and is fairly rapid. Mineralogical analyses may be thus made at a cost considerably less than that of chemical analyses of a similar degree of completeness. The results obtained by this method should not vary in any item by more than 1 per cent. of the total weight of the sample, and may be made very much better than this by the exercise of greater care in the microscopic counting (see below). The accuracy of the hand sorting 'is of course dependent upon the experience and carefulness of the analyst. . After a month's practice, the writer was enabled to turn out these analyses at the rate of four in 33 hr. of working time. It was found most economical to handle four samples at once. The samples analyzed weighed froth 290 to 340 g. each. The same method could be applied to larger or to smaller samples, within reason able limits. The following list covers the necessary apparatus and equipment: 1 good balance capable of weighing accurately to tenths (or, better, hundredths) of a gram, and of handling quantities up to 200 g. in weight. 1 Westphal balance, registering densities to two or three decimal places. 1 Meker or Bunsen burner, and gas supply. 1 nest of sieves, 10, 20, 40, and 100 meshes to the inch.

Jan 5, 1915

By H. C. Heard

INTRODUCTION As the world's population expands and nations struggle to better their relative position and standard of living, increased emphasis is being directed to the exploration and production of mineral resources, to the mitigation of natural hazards such as earthquakes and volcanic eruptions, and to geotechnical engineering projects such as high-level nuclear waste disposal, underground military facilities, and transportation tunnels. Several topics are common to all of these endeavors. One is the characterization of the rock mass in situ, including the definition of the initial environment (e.g., temperature, stress, etc.). A second is, depending upon the use of the underground or the desired result, the manner in which the boundary conditions or the environment are to be changed by man. Next, the physicochemical behavior of the rock mass must be measured, or inferred with uncertainty limits placed on this behavior, over the appropriate range of environmental conditions (e.g., temperature, chemistry, etc.) for the application proposed. And last, an appropriate, validated predictive model must be applied to estimate the rock mass response to the perturbation. In the period preceding about 1955, only relatively simple testing of soils and rocks was commonplace, partly because the environment (depth) to which these data were applied was not so extreme as it is at present and partly because less precise predictions of material response were acceptable. Only limited and relatively simple test data seemed to be needed to guide the engineering. At the present time and certainly in the future, as we extend our interaction with the earth's crust to greater depths and impose more extreme perturbations on it, we need a larger body of data, deter- mined under much more complex conditions, in order to make the required predictions. The present societal problem of high-level radioactive waste disposal is a case in point. We in the rock

Jan 1, 1982

By Henry M. Howe

In my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel: the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.' Sand us. Iron Molds.—If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag is much greater in the former than in the latter, because in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Jan 1, 1910

By C. W. Tomlinson

The analyses which have been made by the writer according to the method described below were made as part of Professor Withey's investigation of the concrete aggregates1 of Wisconsin, in the hope of throwing light on the extent and nature of the influence of the mineral-ogical constitution of aggregates upon the properties of the concrete and mortar made from them. This method was found most satisfactory after four weeks of experiment and modification. It attains an accuracy quite sufficient for the purpose of the analysis, and is fairly rapid. mineralogical analyses may be thus made at a cost considerably less than that of chemical analyses of a similar degree of completeness. The results obtained by this method should not vary in any item by more than 1 per cent. of the total weight of the sample, and may be made very much better than this by the exercise of greater care in the microscopic counting (see below). The accuracy of the hand sorting is of course dependent upon the experience and carefulness of the analyst. After a month's practice, the writer was enabled to turn out these analyses at the rate of four in 33 hr. of working time. It was found most economical to handle four samples at once. The samples analyzed weighed from 290 to 340 g. each. The same method could be applied to larger or to smaller samples, within reasonable limits. The following list covers the necessary apparatus and equipment: 1 good balance capable of weighing accurately to tenths (or, better, hun- dredths) of a gram, and of handling quantities up to 200 g. in weight. 1 Westphal balance, registering densities to two or three decimal places. 1 Meker or Bunsen burner, and gas supply. 1 nest of sieves, 10, 20, 40, and 100 meshes to the inch.

Jan 1, 1916

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world's produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

By Herbert Hoover

THE Federation of Engineering Societies has been created for the sole purpose of public service. This initial meeting surely warrants some discussion of a few of the problems to which this organization, for expression of the --. engineering mind, can quite well give consideration. Some of the greatest of the problems before the country and, in fact, before the world, are those growing out of our industrial development. The enormous industrial expansion of the last fifty' years has lifted the standard of living and comfort beyond any dream of our forefathers. Our economic system under which it has been accomplished has given stimulation to invention, to enterprise, to individual improvement of the highest order, yet it presents a series of human and social difficulties for the solution of which we are groping. The congestion of population is producing subnormal conditions of life. The vast repetitive operations are dulling the human mind. The intermittency bf employment due to the bad coordination of industry, the great waves of unemployment in the ebb and flow of economic tides, produce infinite wastes and great suffering. Our business enterprises have become so large and complex that the old personal relationship between employer and worker has to a great extent disappeared. The aggregation of great wealth, with its power of economic domination, presents social, economic ills which we are constantly struggling to remedy.

Jan 1, 1920

By Webster, Wm. Reuben

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented mill serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford1 found that "oxygen has a relatively small effect on the properties of copper." Johnson, on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior to deoxidized copper . . . where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

By Joseph Kelly

DEPLETION of anthracite resources in Lackawanna County, Pennsylvania, has forced the recovery of coal tracts formerly considered unminable. Chief among these are the large areas of outcrop coal lying on a heavy pitch on the mountain sides, abandoned thirty or forty years ago as too costly and too hazardous to mine. The old companies, in many instances, stopped their chambers 80 or 100 ft. hack from the actual outcrop, and then dropped back another 100 ft. before starting to rob the pillars, thus leaving large areas of coal. Recovery of this coal naturally leads to mining hazards not encountered years ago. The first step is to sink a slope from the surface with the pitch of the vein, and then drive counters across the pitch as close to the robbed area as proper protection for the lower side of the -counter will permit. Next, the old chambers are advanced or new ones driven in the solid, as the conditions require. As these chambers approach the outcrop the real safety work begins-that of preventing the miner from being buried or locked in by an avalanche of mud.

Jan 1, 1936

By W. J. Rude

LARGEST of the known commercial deposits of pebble phosphate are those found in Polk County, Florida. The phosphate bed, commonly known as the matrix, will consistently average 6 to 9 ft. in depth, and is found under 3 to 60 ft. of over-burden. The phosphate pebbles, white and black in color, varying greatly in grade, are found imbedded in a matrix of sand and clay; and range in size from the fines to pebbles 1 1/2 in. in diameter, although the average coarse size is approximately 1/2 in. in diam¬eter. On some of the washers all material under 14 mesh is lost. High-grade phosphate (75 per cent plus of bone phosphate of lime, CasP2Oa) is generally soft, the pebbles breaking up during the mining operation and in pumping; low-grade phosphate, 67 to 69 B.P.L., is black in color with hard pebbles with no loss encountered in pumping.

Jan 1, 1941

By J. E. 214-000-000-010 Warren, M. R. J. Wyllie, T. Meidav, L. Scharon, R. Uhley, A. J. deWitte

By considering the stoichiometry of the underground combustion process, an equrztion was derived relating the point velocity of the combustion front as a function of the air flux, fuel content, efficiency' of oxygen uitilization, hydrogen:carbon ratio, and ratio of carbon dioxide In carbon monoxide produced. In addition, an equation for cnlcrllating the amount of injected air necessary 10 produce the oil from I Cu. ft of reservoir space was derived. This equation has a direct bearing on evaluating compression costs for the process. Values calculated from these equations are in good agreement with experimentnlly obscrvcd values obtained from laborator) tube runs reported in the literature. The equations are also u\eful for atlcrlyzinf: experinlental data for inconsistencie.r.. I NTRODUCTION The injection of energy in the form of heat into an oil-bearing formation as a means of increasing the recovery of oil has been the subject of much discussion and experimentation as far back as 1920. The ideas have ranged from the injection of steam to the direct use of electricity as a means of getting thermal energy into a formation. However, most laboratory and field studies have been confined to the process whereby a portion of the crude in the reservoir is burned to generate the necessary heat to increase the mobility of the oil by reducing its viscosity. A recent paper by W. L. Martin, et al.', described the results of a number of laboratory experiments in which the combustion process was studied in a sandpack. Studies such as this indicate that with the temperatures involved, the oil is partially coked in this process and it is this coke which provides the fuel for combustion. The combustion of this residual coke can be analyzed theoretically by applying simple stoich-iometric principles to the combustion process. It is the purpose of this paper to compare the results reported in these experiments with those obtained from theoretical considerations. The variables studied by Martin, et al, among others, include combustion front velocity, air flux, oxygen utilization, fuel concentration, ratio of carbon dioxide and carbon monoxide in combustion gases, and the hydrogen:carbon ratio of the residual fuel. All these variables come into consideration when the stoichiometry of the combustion process is studied. The experimental conditions and results are tabulated in Tables 3 and 4 of Ref. 1. For purposes of comparison with calculated results, it was necessary to change the units of a number of the variables. UNDERGROUND COMBUSTION STOICHIOMETRY The combustion or oxidation of the carbonaceous residue or "coke" on the sand can be described in terms of the equation: where n is atomic ratio of hydrogen to carbon, m is ratio of moles of CO2 to CO produced, and CH. is taken as the unit molecular weight, realizing that actually the coke has a large range of high molecular weights. Assuming that all the fuel laid down in the sand is burned, the ratio of moles of oxygen consumed to moles of coke can be written as follows. Moles 0MolesMolescoke In terms of moles O2 per pound of coke, where 12 + n is the molecular weight in pounds per mole. If the 0, consumed is measured in standard cubic feet (60°F and 1 atm) and the coke in pounds per cubic foot of formation, 2, then:

By Susasn Leiter

THAT oxygen in copper has been a source of trouble is well known and that that trouble has been real in the commercial world has been shown by Fuller.1 Moore and Beckinsale's paper2 at the annual meeting of the Institute of Metals in London, 1921, called forth considerable discussion. Prof. T. Turner expressed the opinion that it was not necessary to have cuprous oxide present in sufficiently large quantities to form either globules or seams in order to produce a bad effect if the copper were gassed. This brought up the question of the solubility of oxygen in copper and the authors desired to know whether there were any evidence of such solubility, because their experience was that whenever there was any oxygen in copper it was present in the form of free cuprous oxide, .which was practically always in the form of globules. Later Hanson, Marryat, and Ford3 stated that for all practical purposes cuprous oxide may be regarded as insoluble in copper. However, they found particles of the eutectic to coalesce to form much larger particles. They suggested that cuprous oxide was actually slightly soluble in copper, for it was diffi-cult otherwise to understand the mechanism by which such coalescence could take place. W. E. Ruder, in discussing that paper, said that his experiments had led him to conclude that a slight solubility must exist to allow for the ready coalescence of oxide particles, but conductivity tests convinced him that that solubility was very small. Nevertheless, there appeared to be a state of admixture of oxide with copper that closely resembled a colloidal mixture which at first was mistaken for a true solution and which usually existed at the grain boundaries.

Jan 2, 1926

By Wieland D. R., Hurst R. E., A. R. Hendrickson

Analysis of acidizing techniques, in correlation with reservoir data and a backlog of past treatments, has resulted in the development of a valuable engineering guide for planning acidizing treatments. Such treatments fall into three categories: (I) acid injection into the pores of the matrix; (2) acid injection into natural formation fractures at less than parting pressure; and (3) combination acidizing-fracturing treatments in which acid solutions (without propping agents) are injected at treating pressures sufficient to open and extend fractures through which the acid flows. Because the spending tirnze of acid during a specific well treatment does not change appreciably, maximunl penetration is attained when the first increment of injected acid is completely spent. Additional acid injection cannot be expected to further extend the benefits of the treatment. Depth of penetration will depend upon the reaction rate of the acid under treatment conditions, the injection rate of the acid into the matrix or fractures and the area-volume relationship existing in the flow channels. Based on Darcy's flow formula, extremely low injection rates must be used in order to keep bottom-hole injection pressures below formation fracturing pressure. As a result, only limited penetration of unspent acid will occur. Treatment records indicate that, in most acidizing treatments, formation parting pressures are exceeded, greatly extending acid penetration. Under these conditions, stimulation benefits are limited to the fracture area produced during the spending time of the first increment of acid injected into the formation. This area may be calculated from laboratory and well data to estimate depth of penetration. This, in turn, may be correlated with productivity data to assist The art of gas and oil well acidizing has been characterized by many changes in treating materials and techniques since its inception. These developments have been designed to provide greater production increases. prolong production declines and shorten payout time. Such improvements have been based primarily on data derived from laboratory research and field experience. As more of the variables influencing these treatments have been recognized and evaluated, acidizing has become less of an art and more of a science. Recent studies of fracturing treatments,' in light of individual well conditions and the results of thousands of fracturing treatments, made possible the formulation of an engineering guide that is now being used to select optimum treating techniques and to forecast probable results of such treatments. A similar analysis of the factors controlling acidizing treatments has been made and is the basis for this paper, The findings herein can be used as a guide in the selection of acidizing solutions and techniques, tailored to fit specific well conditions and to provide optimum stimulation per dollar cost. Acidizing treatments may be classified into three basic categories—(1) treatments in which the acid is injected uniformly into the pores and flow channels of the matrix, (2) treatments in which the acid enters natural fissures and fractures in the formation at less than fracturing pressures and (3) injection of acid into the formation at a pressure sufficient to open and extend fractures into the rock through which the acid penetrates (without the inclusion of a propping agent). TYPE 1 — MATRIX ACIDIZING This category consists of treatments in which acid solutions are injected into a homogeneous carbonate

By W. L. Dennen, W. W. Wirth

Research looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than development work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand. An early step toward the permanent type of roof support was the installation of "brick pillars or perfect arched brick rooms" instead of

Jan 1, 1940