Search Documents

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"' an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)', four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By Franklin G. Pardee

IN 1920 the Minnesota Tax Commission estimated a reserve of 1,341,674,538 long tons of iron ore in Minnesota, the Michigan State Tax Commission report showed 199,092,855 long tons in reserve in that state, and the Wisconsin Geological Survey set the Wisconsin reserves at 21,500,000 long tons. The total reserve that year for the Lake Superior District amounted to 1,562,267,393 long tons. Ten years later the reserves of iron ore in these same districts were Minnesota 1,235,227,510, Michigan 168,349,823, and Wisconsin 23,000,000, or a total of 1,426,577,333 long tons. The decrease in ore reserves in this ten-year period was 135,690,060 long tons, but the shipments were 520,746,975 long tons. In other words, the ten-year depletion in reserves was only 8.68 per cent. If similar conditions carry into the future this calculation would indicate a life for the ore reserves of the Lake Superior region of over 100 years.

Jan 1, 1933

By D. H. Newland

CERTAIN observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U.S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.1 The deposits of Canada are described by L. H. Cole.2 Several states, including Kansas, Oklahoma, Iowa, Michigan, and New York, have had special surveys made their of gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago.

Jan 9, 1921

By Eugene Guccione

It would be extremely difficult and unfair to compare the United States to Australia when wondering about which of the two countries offers the best opportunities for running a mining operation. However, if somebody would ask "Where is the best place to mine outside the US?"-I'd answer without reservations: Australia. Some of my Australian mining friends will disagree with me for my giving their country such a high rating. And they'll probably accuse me of being an optimist by telling me, as one of them did, that "the difference between an optimist and a pessimist is that the pessimist is better informed."

Jan 1, 1977

By James Howe

EVERY engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of consider-, able money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate sized rope, about 1 ¼ in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until, it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be com-pared with the service of previous years with any fairness to the wire-

Jan 2, 1922

By Henry Tobelmann

THE location, mode of occurrence of ore, and preliminary tests leading to the development of the present leaching process and the building of the present plant on the property of the New Cornelia Copper Co. at Ajo, have been described in previous papers presented to the Institute and in the, discussions thereof.1 It is sufficient to say that these tests began early in July, 1912, and were continued to the close of January, 1916; that small tests at Douglas were followed by the construction of a 1-ton plant at the mine; and this was followed by the operation of a 40-ton plant for 14 mo. In all about 15,000 T. of ore were treated experiment-.

Jan 2, 1919

By T. R. Wright

THE Corporation operates concentrators in four camps: Casapalca. Morococha, Cerro de Pa-co, and Mahr. The present concentrator at Cerro de Pasco is the newest having been completed in 1943. and that at Casapalca the oldest, having been built originally as a gravity concentrator, in 1889. Prior to 1925 the Corporation's milling operations were confined to the beneficiation of silver-bearing copper ores, and treatment of these ore: by flotation was started in 1918. Although fairly large deposits of complex, fine-grained lead-zinc ores existed, little progress had been made in the treatment of such ores--in Peru or elsewhere-until the early 'twentics. The Casapalca concentrator began the selettive concentration of complex leadzinc ores by all-flotation methods in 1925, or contemporaneously with the commercial development of selective lead-zinc flotation in the United State:.

Jan 1, 1945

By HENRY M. PARKS

THE total production of all metals in Oregon to date is estimated at $160,000,000; ~115,000,000 from eastern Oregon and $45,000,000 from the western part of the state. In 1916 the metal production of the state was approximately $4,000,000, while the present annual production has dwindled to a little less than $1,000,000. Western Oregon The state of Oregon contains several metal-bearing areas, widely scattered in different regions. More than half of its coast is fringed with a belt of auriferous sands which sometimes are rich in fine gold. A second mining field, the chief producing one of western Oregon, is situated in the southwestern part of the, state and includes Jackson, Josephine, Douglas, Coos and Curry counties. It may be considered as the northern extension of the gold and copper belt of California. A third region in western Oregon is that on the western slope of the great Cascade range in the Bohemia, Blue River, Quartzville, North Santiam and Ogle Creek districts-from the Siskiyous on the south almost to the base of Mt. Hood near the Columbia River on the north.

Jan 1, 1925

By Ferdinand H. Regel

Concentrating-machinery has been wonderfully improved during the past few years both in technical efficiency and in economy of power; and, in the writer's opinion, the prosperity which the mining industry has of late enjoyed is due in large part to this improvement. Many properties are yielding handsome profits at the present time which were considered, a few years ago, too low in grade of ore to be profitably operated; and I think that fully half of these once worthless properties owe their successful development to recent improvements in concentrating-machinery. The present paper calls attention to a jig and an ore-classifier of new design, invented by Mr. John Klein, and already used in the lead-region of SE. Missouri, and in the Philipsburg dis-

Jan 1, 1902

For the year ending February, 1936 PRESIDENT AND DIRECTOR HENRY A. BUEHLER ROLLA, Mo. PAST PRESIDENTS AND DIRECTORS FREDERICK M. BECKET NEW YORK, N.Y. HOWARD N. EAVENSON PITTSBURGH, PA. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y.

Jan 1, 1934

By Werner Joseph, Richard R. Knobler

When the first batch of refined copper ingots was cast at Mantos Blancos in January 1961, eight years of exploration, development and metallurgical pioneering by Mauricio Hochschild & Co. had come to a successful conclusion. This Chilean copper deposit, located in the Atacama Desert 30 miles from Antofagasta, is now producing approximately 20,000 tons of copper per year. The Mantos Blancos deposit has been known since 1912 and various attempts had been made to work the high-grade zones before the present operation was started. The major drawback of the ore to any previous development was its chloride content which varies between 0.4% and 1.5% C1. Although the chloride ruled out the conventional leaching-electrolysis scheme, it did lend itself to the process of precipitating the copper as cuprous chloride.

Jan 1, 1962

By Y. Nakada, U. F. Kocks, B. Chalrners

THE orientation dependence of work hardening has previously been studied over the entire range, i.e., including special orientations of high symmetry, in aluminum1-3 and silver.* The differences between various orientations are substantial, and the trend is the same in all fcc crystals. However, there are quantitative differences in behavior between aluminum and silver at room temperature, particularly in the (100) orientation. While many experiments on gold have been reported,5'9 none included the special orientations. We therefore undertook tension tests on gold crystals of the axial orientations (100),(110), (Ill), (211), and, as a representative of single slip, one whose Schmid factor was 0.5 (hereafter referred to as m = 0.5). Single crystals of dimensions 1/4 by .1/4 by 6 in. were grown from the melt1' at a rate of 4 in. per hr, using gold of 99.99 pct purity obtained from Handy and Harman. A growth rate of 1/8 in. per hr, or a purity of 99.999 pct,ll produced no difference in results. The crystals were annealed at 1000°C in air for 24 hr and furnace-cooled down to room temperature, after which they were electro-polished in a solution of potassium cyanide (40 g), potassium ferrocyanide (10 g), soda (20 g), and enough distilled water to make 1 liter of solution, at a current density of 0.02 amp per sq mm. After 2 or 3 hr, a very smooth surface was obtained by this method. Nine m = 0.5, two (loo), one (110), three (Ill), and one (211; crystals were tested at room temperature in a floor-model Instron machine at a tensile strain rate of 0.5 pct per min. The accuracy of the stress measurement was k10 g per sq mm up to 500 g per sq mm, k2 pct for higher stresses. The strain measurement was accurate to t2 pct. The scatter of stress at a given strain among the crystals of the same orientation was small, *5 pct being the largest. The representative stress-strain curves for various orientations are shown in Fig. 1. Table I summarizes the work-hardening parameters as used by seeger.12 Results of other investigators are also included in this table for comparison. There are no previous data for the corner orientations. Values for m = 0.5 crystals agree fairly well with those of Berner. Tm is defined as the stress at which the stress-strain curve begins to deviate from linearity of Stage 11. However, in practice this is a very difficult value to estimate because each investigator has a different idea of linearity. Therefore, the comparison with the values of other investigators may not be valid. In the present experiment, (100) crystals had the highest 111, followed by (111) crystals. The work-hardening rate in Stage I1 was highest for the (111) crystal followed by the (100) crystals. Our value for 0x1 of m = 0.5 orientation agrees very well with those of other investigators. 1) Single-Slip orientation (m = 0.5). These crystals were oriented so that the primary-slip vector was contained in one side face. The dimension perpendicular to this side should then not change if single slip indeed takes place. Within the accuracy of measurement, this dimension did not change during the deformation. Since the accuracy is k0.2 pct, the amount of secondary slip is less than 0.7 pct of the slip on the primary-slip system at 30 pct tensile strain. This is in conformity with the results obtained by Kocks" for aluminum crystals. The tensile axis moved toward (211) during the deformation. Slip bands, Fig. 2(a), were very fine and closely spaced. Some deformation bands were observed. There were no clear-cut cross-slip traces such as the ones observed on aluminum m = 0.5 crystals. 2) (111) Crystals. The orientation of the tensile axis was stable during the deformation. From this observation, one can deduce that at least three slip systems must have operated, and probably all six because the remaining three all have cross-slip relation to one of the first three.' It was very difficult to observe the slip markings. Consequently, we could not confirm by this method that six systems were operative during the deformation. At high strains (above 50 pct shear strain), this orientation had the highest stress-strain curve. At 80

Jan 1, 1964

By N. J. Grant, B. C. Giessen, Paul Predecki

ALLOYS of gold, silver, and aluminum with elements of the groups BII, BIII, BIV, and BV were prepared by a rapid quenching technique (splat) and were examined by X-ray diffraction. Five new intermediate phases were found and will be described briefly herein. For the gold and silver systems, the concentration ranges having an electron/atom ratio e/a of 1.4 to 1.5 ("3/2 Hume-Rothery phases") were studied primarily. Master alloys were prepared from high-purity metals (99.9+ pct or better) by melting either in evacuated fused silica capsules or by nonconsum-able-electrode arc melting in an argon atmosphere. Small pieces, 20 to 50 mg, of each alloy were blast-atomized to form a splat, by a technique similar to that described by Duwez and Willens.1 The technique used for this study is described in detail in Ref. 2; it utilizes a resistance-heated graphite crucible with a small hole at the bottom, directed toward a metal substrate or quenching plate. The prepared alloy rests over the fine hole, through which it is expelled by an explosion shock wave in the form of fine droplets (1 to 50 µ) of molten metal onto a copper or silver substrate, which is maintained at about -190°C. The resulting very high cooling rates (see Ref. 2 for quantitative measurements) can prevent the process of nuclea-tion and growth in many instances, resulting in the formation of metastable phases. The splat particles were transferred to a GE-XRD5 diffractometer and maintained at -190°C, where they were examined with CuKa radiation. The samples were then allowed to warm to room temperature or were heated to higher temperatures until the equilibrium structures formed. Of fifteen alloy systems considered, nonequi-librium structures were encountered in six; these are described below and summarized in Table I. In the system Au-Sb a metastable £ phase (A3 type, hcp, a = 2.898 + 0.002A; c = 4.731 * 0.004A; c/a = 1.633) was found in the concentration range Au + 13 to 15 at. pct Sb. This phase is isomorphous with the stable phases in the systems Au-Cd, Au-In, and Au-Sn, all at an average e/a ratio of 1.4 to 1.5. The concentration range of one-phase metastable was deduced from the small amounts of supersaturated gold solid-solution phase present in the splat product. It was found that ? could also be retained by splatting onto a substrate held at room temperature: however, decomposed into the equilibrium phases Au + AuSb2 after heating to 200°C for 1/2 hr, or on holding the powdered splatted alloy at 20°C for several months. Calorimetric measurements will be made in an attempt to decide the question whether ? is metastable at all temperatures or whether it is a stable phase at low temperatures. There is evidence that another phase, possibly also close-packed but with a different stacking sequence, can be obtained by rapid quenching of alloys with a different antimony content. Klement, Willens, and Duwez3 reported the existence of an amorphous phase on quenching Au-Si alloys (25 at. pct Si) to - 196°C. They found that on heating to room temperature another phase of unknown crystal structure was formed. This was confirmed (see Table I); however, the new crystalline phase, designated as ?, could also be formed simply by rapid quenching to room temperature, and even was found to exist already in the as-cast Au + 20 at. pct Si alloy. It was found that ? decomposed into Au + Si on the specimen surface at room temperature. This behavior, and the question whether or not there is an equilibrium-temperature region for ?, have not yet been resolved. It is probable that ? (Au + 20 to 21 at. pct Si) is cubic of the -brass type (D81-3) with a = 9.60, + 0.01A and N = 52 atoms per cell [compare 6 (CU-Sn)4]. Except for two very weak lines, the powder pattern of about thirty lines could be indexed on this basis; however, a determination of the atom positions has not yet been attempted. For Au-Ge the C phase was observed at about 21 at. pct Ge as reported by Luo et at.5 Lattice parameters a = 2.876A, c = 4.73,A, c/a = 1.64 were found. In the Au-Pb system, formation of a ? phase was not observed, but in the lead-rich region at 75 at. pct Pb, broad peaks belonging to an amorphous phase were found. The maximum diffracted intensity occurred at 28 = 32.4 deg which is about 1 deg larger than the position of the (111) line of lead (Cuka). For Ag-Pb, an amorphous phase analogous to the one found in the Au-Pb system was observed; this metastable phase exists probably at about 75 at. pct Pb. Since no lead-rich alloys were tested, all alloys consisted of silver + amorphous phase at -190°C. In A1-Ge alloys, line-rich and complex powder patterns were obtained at about 30 at. pct Ge; they bear similarities to those of aluminum and germanium, but are of lower symmetry; the existence of more than one intermediate phase is possible. The authors are grateful to the Kennecott Copper Corp. for Fellowship support, and ARPA (Contract

Jan 1, 1965

By E. O. Wagner, V. F. Parry, W. S. Landers

Development work has shown that the yield of primary tar from coal is proportional to the heat in the volatile matter of the coal and that the yield of tar from noncoking coals may vary from 10 to 45 gal per ton on the ash-free and moisture-free basis. Pilot plant operations have proved that 100 to 135 pct of the bench-scale carbonization-assay yield of tar can be obtained. FOLLOWING investigations by the Denver Bureau of Mines on drying fine coal in the entrained state,'. ' Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help offset the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee," and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal. but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used. Any bituminous material will decompose when heated to about 900°F to yield primary tar, gas, and char. The quantity of tar obtained from various coals depends on their rank and volatile content and to some extent on rate and method of heating. The liquid products derived from thermal decomposition of peat, brown coal. lignites, oil shale, and noncoking bituminous coals can be easily liberated by rapidly heating these materials in a fluidized bed at about 500°C (932°F). Since it takes only a few minutes to heat small particles of fuel to carbonizing temperature in a fluidized bed, processing plants can be built to handle up to 50 tph at relatively low cost. The pioneering development work being conducted at Rockdale, Texas, by Alcoa and Texas Power & Light will solve many engineering problems of such operations. The Bureau of Mines at Denver has studied the carbonizing properties of several hundred coals by small scale assay at 500°C, deriving a simple correlation between the potential yield of tar and the proximate analysis. This correlation, shown in Fig. 1, compares the heat in the volatile matter of the coal with the potential yield of primary tar. The yield of primary tar varies from 12 to 50 gal per ton of pure coal." About the same amount of heat is needed to * MAF equals moisture-and-ash-free basis. distil any dry coal at 500°C, and the time required to carbonize a given particle size is about the same for any coal. It is therefore obvious that coals rich in volatile matter will show the greatest profits when processed. Texas lignites are rich in volatile matter, which contributes some 5700 Btu per lb of MAF coal, and the potential primary tar and oil yield from this lignite averages 12 pct by weight or 27 gal per ton from the pure lignite. Texas lignites are considerably richer in potential tar than lignites of North Dakota and Montana. During 1950 the Bureau of Mines conducted many experiments on carbonizing fine dry coal in the entrained state, publishing a report4 n major features of pilot and commercial-size units required to carry out the process. Additional experimental work has been done at Denver and the pilot plant has been improved, particularly the facilities for studying removal of fine dusts from tar vapors and gases at high temperatures by electrostatic precipitation. A number of materials have been carbonized, including sawdust, peat, brown coal, Brazilian oil shale, lignites, and the lower rank bituminous coals having noncoking properties. Straight coking coals cannot

Jan 1, 1957

By Blamey Stevens

(San Francisco Meeting, October, 1911.) My previous paper is entitled, The Laws of Igneous Emanation Pressure. The present paper lays no claim to the exactitude and completeness of a law, since it is of a provisional nature and may be disregarded when experiments have established a basis for more exact reasoning. The general physical states in which aqueous emanations may occur are first considered. The possible physical conditions under which the mineral elements may occur in emanations are then discussed, and a classification of deposits, dependent on emanation, is proposed. A system of scientific experimental investigation is outlined, and it is shown that the physical and chemical properties of emanation may be exactly determined thereby. The investigation is urged as feasible and simple, and not necessarily requiring large and costly apparatus. It is the only step necessary to make possible the formulation of a complete set of laws of igneous emanation. Process of Emanation. In a rising column, magma ranges in temperature from 900° to 1,200°C. Exhalation must begin at some fairly great depth. What this depth may be we can only surmise, since no experimental evidence is available. Exhalation, however, continues as the magma flows upward, until at another level the occluded gases have all escaped. This depth is probably upward of 5,000 ft. (See Fig. 1.) All exhalations must come from between these two levels. As the whole emanation is the sum of the exhalations and residues, the residues must come from below the uppermost level. They will be most abundant when coming, from those parts of the intrusion which have solidified below the lower level.

Apr 1, 1912

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature microhardness of as-grown and annealed MoaC single crystals was measured on the (0001), {2110), and1012) planes using Knoop and Vickevs indenters at loads ranging front 25 to 1000 g. The orientatimz dependence of hardness with respect to crystal axes was also studied. The average random hardness of as-grown crystals was determined to be 1520 kg per sq nm. Annealing to 2000°C decreased. the average hardness by 150 units. An increase in hardness after annealing at 2200 ;C was noted. Optical and electron microscopy revealed slip and twin traces on all planes studied, as produced by mi-cvohavdness indentations. Basal (0001)(2i10) slip was determined to be the primary slip system and was substantiated by electron transmission microscopy. A secondary {1010)(2110) slip was produced by mi-crohardness indentations. The lattev also produced twinning- of the {10i2)[0001] type, as proven by electron diffraction. Electrical resistivity and elastic-modulus anisotropy were found and correlated with hardness anisotropy and Mo2C crystal structure. Elastic-modulus values were obtained by microhard-uess and ullrasonic methods. Bonding mechanism of Mo2C is discussed. ROOM-TEMPERATURE microhardness indentations are useful for studying hardness anisotropy, slip, and twinning in brittle materials. Slip has previously been produced in this manner in and WS~~.~ Recently, the authors5 reported slip of the {10i0)(11~0) type produced by high pressure and microhardness indentations on hexagonal TiBz (c/a = 1.066) single and polycrystals. This slip system was also reported by French and ~homas' and Taka-hashi and ~reise~ for hexagonal WC (c/a = 0.976) crystals. These results suggest that prismatic rather than basal slip is favored in hexagonal nonmetallic materials having a c/a ratio considerably less than the ideal (1.633). Buerger precession and cylindrical X-ray rotation patterns were previously' taken on cleaved sections of the Mo2C single crystals studied in this work. Th~y were found to be hexagonal MoaC with a. = 3.0233A, co = 4.7344A, and C/O = 1.5660. The latter ratio is close to that of the beryllium metal (c/a = 1.57), which slips primarily on the (0001) plane: but also slips on the (1010) planes.'0 ~irconium" (c/u = 1.59) and titanium12 (c/o = 1.59) deform mainly by slip on nonbasal planes which contain a close-packed direction. This is due to the fact that for these two metals the initial resolved shear stress for slip on the (10i0) prismatic planes is lower than that on the (0001) plane. The prominence of basal rather than prismatic slip in metals of high c/o ratios is shown by cadmium (c/a = 1.89), zinc (c/a = 1.86), and magnesium (c/a = 1.62) which deform mainly by basal slip. However, in case of the latter, by stressing magnesium crystals in tension or compression parallel to the basal plane, slip on (10i0) planes can also be produced.13 Several hardness values for polycrystalline Mo2C are reported in the literature: Biickle ' and Samsonov'~ give a value of 1800 and 1479 kg per sq mm, respectively, at a 100-g load; and Kieffer and Benesovsk~'~ report a value of 1950 kg per sq mm at a 50-g load. ~ott'~ reports a Vickers hardness value of 2000 kg per sq mm, with the load unspecified. A Rockwell A hardness value of RA = 88 has also been reported.'' In the present work, for comparison with single-crystal Mo2C hardness values, a Khnloo value of 1600 It 150 kg per sq mm was found on 99.6 pct pure and 99 pct dense hot-pressed Mo2C. This work was undertaken partly to explain the considerable differences in hardness values reported for polycrystalline Mo2C. EXPERIMENTAL The Mo2C single crystals investigated were prepared by a Verneuil-type process using an electric arc by the Linde Co. of the Union Carbide Corp.lg The largest specimens grown were boules 7 mm in diam by 40 mm in length. The crystals had an average density of 9.04 g per cu cm, with a Mo + C content of 99.8 wt pct. The major impurities were: 100 ppm each Na, Zr, and Ca; 85 ppm 0, 55 ppm Fe, and 10 ppm each Cr and Ta. The crystals were found to be carbon-poor, the average carbon content being 5.73 wt pct (stoichiometric value is 5.89 pct). The molybdenum content was found to be 94.08 pct, which is nearly stoichiometric. Electron-microprobe traverses of selected specimens were done with a Phillips-AMR microanalyzer. Thin-film and carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to optical and electron-optical studies, specimens were mounted in Lucite and polished on a vibratory polisher using diamond-paste grades ranging from 9-1 p and Linde A powder for up to 48 hr. Dilute nitric acid was used for thin-section polishing and chemical etching for 1-15 min. Electrical-resistivity measurements at room temperature were taken with a Rubicon bridge, using gold contacts. For hardness measurements, a Tukon Microhardness Tester Type FB with Knoop and Vickers indenters was used. Measurements were taken at loads ranging from 25 to 1000 g; however, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Indentations of cracking classes 1 and 2 only were considered for hardness determinations.20)21 (There are six cracking classes, ranging from "class 1" for a perfect inden-

Jan 1, 1967

By CYRIL W., William Campbell, Henry M. Howe

THIS paper gives the results of an investigation of the behavior of the argentiferous cobalt-nickel arsenides of Temiskaming, Ontario, in roasting, made in the metallurgical laboratories of the School of Mines, of Columbia University in the City of New York. The ore was kindly given by the owners of the La Rose and Trethewey properties at Cobalt, Ontario, and Mr. E. J. Hall, Tutor in Assaying in Columbia University, has helped us much. I. OBJECT OF THE INVESTIGATION. The object of the investigation was to learn:- 1. The temperature at which the arsenic is most rapidly expelled; 2. The thoroughness with which it is expelled by prolonged roasting at this temperature; 3. The effect of adding charcoal (a) near the end of the roast and (b) at the beginning of the roast. II. NATURE OF THE ORE. The important ores mined in the Temiskaming deposits are native silver-with small amounts of dyscrasite (Ag6 Sb), argentite (Ag2S), pyrargyrite (Ag3SbS3)-smaltite (CoAs2), chloanthite (NiAs2) and niccolite (NiAs). Mispickel (FeAsS) and cobaltite (CoAsS) also occur in smaller quantities. The average composition of the ore shipped from this district for the first six months of 1905 -was: silver, from 4.1 to 4.8 per cent.; cobalt, from 6.9 to 8.2 per cent ; nickel, from 3 to 4.7 per cent ; and arsenic, from 30.9 to 34.6 per cent. The ore which we treated consists chiefly of smaltite ; In our laboratory-work

Jan 1, 1907

By JULIAN HINDS

Industrialization is raising the standard of living of people everywhere. The common man is demanding and getting more of everything. Perhaps more markedly than most other things, he is consuming more water. A hundred years ago water for domestic use, in all but a few large centers, was lugged from wells in buckets. This still is true in many rural areas, even in the enlightened United States of America. but pumps and pressure systems are rapidly replacing the "old oaken bucket," even on farms and in isolated country homes. Nevertheless, many still fail to see water as a ?commodity? in the same sense that coal, lumber, fertilizer, and bread are considered as commosities. Water is too frequently taken for granted.

Jan 1, 1949

By C. H. Jacoby

Since salt, sodium chloride, is an essential mineral to animals and humans alike, the delineation of the salt deposits of the world has been continuous from prehistoric times. As man explores deeper into the crust of the earth, particularly in search of petroleum, numerous new deposits of salt have been recorded. This paper deals with the factors that equate the current economic value of a salt deposit. The value of a salt deposit is not only determined by the chemical purity of the sodium chloride, but also the method of extraction to be used, the use of the product, and/or the use of the deposit. Salt is basically an inexpensive industrial commodity where large tonnages must be available to conduct a successful mining operation. Therefore, not only must the deposit contain these large tonnages, but also it must be accessible and transported as low cost freight to a large market. The geological environmental conditions surrounding the deposit must be such that it will be conducive to low cost mining operations. These conditions include not only the depth, size, shape, and internal structure of the deposit, but also the characteristics and extent of the overlying ground water.

Jan 1, 1973

By E.G. Lewis, l.M. Barker

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943