Search Documents

By George S. Rice

GROUND movement from mining, whether it be for coal, metal, industrial minerals, or .oil, will always present many difficult problems. These are especially serious when valuable surface improvements may be badly damaged. The mine itself, if mining methods are not suitable to the formation, is subject to heavy falls of the main roof in the working places; and with certain structural conditions the movements may cause in coal mines disastrous bumps and outbursts of gas, and in deep metal mines rock bursts. In open-cut work rock and earth slides may result. Absolute prevention of ground movement from mining is impossible unless large pillars are left unmined,

Jan 1, 1937

By A. F. Crawley

The density and viscosity of 1iquid thallium have been measured by absolute methods to temperatures of about 200° and 150°C, respectively, above the melting point. These new data reported, especially density data, do not closely confirm previous work. Density p, in g per cu Cm, is shown to vary linearly with temperaluve t, in °C, according to the equation p = 11.658 - 1.439 X l0-3t. The viscosity data obey the well-known Andrade equation nv1/3 = A exp C/vT , the constants A and C for thallium having values of 2.19 x A and 79.648, respectively. This paper reports some new data for the density and viscosity .of liquid thallium. Measurements of these fundamental physical properties were undertaken as part of a continuing research program at the Mines Branch, Department of Energy, Mines and Resources, Ottawa. Canada. A literature search has revealed that data are so scarce that there could not be a consensus on the true values of the density and viscosity of liquid thallium. To be more specific, there exists only one set of viscosity data' and only two acceptable sets of density data,273 one of which is limited in scope.3 In Liquid Metals Handbook,3 another density study is reported but indications of impurities in the thallium render the results suspect. In this situation, further careful experimentation was required to realize the true density and viscosity of thallium. EXPERIMENTAL METHODS Density. Densities were determined using a graphite pycnometer. The technique and its accuracy have been discussed in earlier papers.4'5 It is considered that experimental data can be obtained which are accurate within +0.05 pct, all sources of random and systematic errors having been evaluated. Density results for thallium were identical whether measured under an atmosphere of argon or a vacuum of 5 x 10-6 torr and, for the most part, the argon atmosphere was used. Viscosity. Viscosity measurements were made in an oscillational viscosimeter by an absolute method—the liquid metal being held in a closed graphite cylinder. Design and operation of the apparatus, constructed in this laboratory, have previously been discussed.6 For thallium, runs were made under a vacuum of about 2 x 10-6 torr. To evaluate viscosity coefficients from the various experimental parameters, the mathematical analysis of Roscoe7 was used. Measurements of the necessary parameters and the accuracy of these measurements have also been discussed.6 The cylinder dimensions were corrected for the anisotropic expansion of graphite, as discussed for density measurements.4,5 It is well-known that thallium oxidizes rapidly and hence a newly machined surface quickly tarnishes in air. The oxide film, however. is nonadherent and is easily removed by rubbing or by solution in water. Hence, immediately before use, both density and viscosity charges were immersed in water, wiped dry, and quickly transferred to the apparatus which was then rapidly evacuated. Specimens removed after determinations were only slightly tarnished and there was no other evidence that tarnishing affected the results. For example, the sharpness of the specimen edges from the containing vessels indicated complete filling by the liquid metal. Thallium of 99.999 pct purity was used in this investigation. Because of its high toxicity care was exercised in handling this material. For example, the melting procedure to prepare machinable ingots was carried out in an open, well-ventilated area, while protective gloves were always worn when handling the solid metal. RESULTS AND DISCUSSION Density. Measurements were made over a tempera-ture range of about 200°C above the melting point. The results are listed in Table I and plotted in Fig. 1. From the graph it is evident that the relation between density and temperature is linear. Such a relation has been observed before in this program for other metals and alloys475 and elsewhere by other workers. A least-squares analysis of experimental data gives the equation: pT1 = 11.658 - 1.439 x 10-3t where p = density in g per cu cm and t = temperature in "C. In Fig. 1, together with the present results, the data of Schneider and Heymer2 in the corresponding temperature range have also been plotted. Evidently, the two sets of data do not agree well, the results of Schneider and Heymer being about 0.6 pct higher. Viscosity. Viscosity data were obtained from the melting point, 303.5°C, up to 457.5"C. The data are listed in Table I and in Fig. 2 the plot of these results demonstrates a smooth curvilinear relation between

Jan 1, 1969

By Anderson, Burton E.

FOR several centuries diamond mining has been an adventurous, profitable and enticing industry in Brazil. Some of the world's most valuable diamonds have been found in this country. Two of the most famous stones are the "Estrella do Sul" (Southern Star), weighing 2541/ karats, and the "Branganca," weighing 1680 karats in the rough and 367 karats cut. For a great number of years the stones extracted and sold were mostly the white diamonds used for jewelry. Within the last thirty years black diamonds have been developed as an abrasive cutting material and in these black diamonds the State of Bahia, Brazil, has a monopoly of the world supply. Carbons, as they are commonly called, are being used for core-drilling, polishing, cutting, wire-drawing, and vari-ous other applications in which such a hard substance is required. Bernard Bandler & Sons, of New York City, have selected, graded and delivered these carbons to the United States markets.

Jan 1, 1932

By Alexander Bowie

In many places throughout the Western mountain plateau regions of the United States coal beds in place have been burned over very extensive areas, the fire evidently originating on the nakedly exposed outcrop of the coal bed and gradually burning its way into the bed for considerable distances under very heavy cover. The surface evidences of the burned-out coal beds are seen in the calcined and discolored rocks overlying the places of the outcrops. The greater the mass of the burned coal the higher the results of its combustion can be seen in the overlying strata. I have noted many instances of this condition in the States of South Dakota, Wyoming, Colorado, New Mexipo, and Arizona. In the lignite fields of Dakota and Wyoming I noted stretches of level country many square miles in extent where the surface rooks were roasted and vitrified by the burning of a great bed of lignite lying nearly level and with a light cover; this is probably the most favorable natural condition for the burning out of a coal bed. The less the depth of the rock covering overlying the coal bed, the better the chance for a continuous supply of air to the fire; but when the coal bed dips heavily into the ground, or even if level, if it passes under a hill or mountain which gives the bed a heavy covering of strata, the fire has more chances of being extinguished from natural causes than in the first condition described. The distance which a crop fire may extend into a coal field is very much influenced by the dip, the thickness of the coal bed, and the nature of the rock covering immediately overlying it. In reasoning on this subject, it would seem logical to assume in the case of a coal-bed cropping at the base of a hill and dipping into it, with an extensive drainage surface above the crop line, that a crop fire would be promptly extinguished by the caving in of the overlying strata and the precipitation of the rainfall from the drainage surface above the outcrop through the breaks formed in the caving strata. This consideration would be more or less effective according to the climate of the location and the nature of the overlying strata. In a humid climate where the rainfall was heavy the water from the natural precipitation alone would probably extinguish a crop fire before it could work its way very far under cover, but in an arid climate this preventive does not seem to be effective.

Jan 1, 1915

By C. F. Smart

The heat treatment of the bronze composed of 88 per cent. copper, 10 per cent. tin, and 2 per cent. zinc, has been investigated by H. S. and J. G. S. Primrose,' and also by the U. S. Bureau of Standards.2 The results obtained by H. S. and J. G. S. Primrose on dry-sand castings subjected to reheating followed by air cooling, or by quenching in water, are shown in Figs. 1 and 2. The values for tensile strength have been converted from tons per square inch to pounds per square inch. Figs. 3 and 4, have been plotted from values obtained by the Bureau of Standards on material of the same composition and treatment. Both investigations show that the ductility of the cast bronze is improved by heating to 700' C. and cooling in air, the strength not being impaired by this treatment. They are not in agreement, howevcr, as to the effect of quenching, Messrs. Primrose reporting a decrease, and the Bureau of Standards an increase, in both strength and ductility when the cast bronze is heated to 600' or 700' C. and quenched. The present investigation was undertaken to study the effect of annealing followed by different rates of cooling, and, in particular, the

Jan 1, 1921

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By C. C. CONCANNON

POTASH is an essential. It is necessary as an ingredient in fertilizers or as a plant food, and certainly one of the great problems, and one of increasing gravity, is the maintenance of agricultural fertility that we may have adequate food supplies. When one thinks of potash one thinks of Germany. The first and most important deposits of soluble potash salts were found in Germany, and it was through Ger- man research and the application of a highly developed knowledge of chemistry that the value of these deposits was recognized and appreciated in the field of agricultural fertilization. The Germans knew that they had something of great value in their potash resources, not only because of the advantage derived from the extensive use of it in their own intensive farming operations at home, but also because of the pressing need for it on the part of other countries. Appreciating the economic value of this in international trade, they fostered the industry to the fullest extent and devoted much attention to well organized propaganda designed to bring out the essential need for potash of German origin throughout the world. Thus every one came to believe that potash was an essential commodity of only German origin and as such it held an extraordinary position in world trade prior to 1914.

Jan 1, 1926

By M. L. Lissberger

entirely suitable for certain uses and even possess advantages over present solders at high temperatures, but they are certainly not suitable for all uses. However, it is conceivable that their use in many places will effect a material conservation of tin. It will probably be wiser to use cadmium in solders where good results have been obtained than in brass where this element will be a source of possible trouble. F. F. Colcord,* New York, N. Y.-—The cadmium-lead solder has a higher conductivity than the lead-tin alloy, which ought to make it advantageous in the manufacture of electrical machinery. In the case of solder for tin-can work, one of the high officials of the American Can Co. said that he fully intended to .give it a good trial, and I do not believe they are going to reach hasty conclusions and run the risk of poisoning the public. Solder, Its Use and Abuse Milton L. LissbeRgeR,† New York, N. Y.—Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, re-melted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 1, 1919

By Charles H. Fulton

IT is assumed that the word "college" for the present purpose signifies technical school or technical department of a college or university. About ten or fifteen years ago, and more recently in some instances the contact between the technical school and the industry, as represented by the operating companies, was very limited. The school made no effort to place its graduates in the industry and the graduate's first position was obtained by his own or his friends' efforts; the friend often was a professor. The industries, or the operating companies, seemingly had little interest in the training of the technical graduates they employed or in seeking to discover their personal characteristics and fitness for the work. In the public mind there was little relation between technical training and industry. Such training was in the field of education; industry was in the field of business; and the interrelationship was not a matter of common knowledge or concern.

Jan 1, 1929

By P. E. Fitzgerald

SOME readjustments in the research programs of most of the oil companics and petroleum engineering schools have been made necessary by the war. The most obvious change has been the conversion from production engineering to problems more closely related to the nation's was effort. Many laboratories now devote much of their time to studies on products to be derived from petroleum. such as synthetic rubber, toluene, and substitutes for critical materials. Others are working to improve motor fuels including high-octane gasoline and the special lubricants required by the wide geographical range of the present conflict. Of great importance is the experience of the geophysicists, who are now devoting a great percentage of their time on instrument research and production or special apparatus required by the armed forces.

Jan 1, 1943

By Victor A. Phillips

A series of strips of a Ni-12.7 at. pct A1 alloy were Prepared containing cubical y'(NisAl) precipitates with edge lengths from 60 to 500A. A particle-free solution-tveated strip was included for cornparison. They weve cold-rolled 95 pct and the effects of particle size on the isochronal (1/2 hr) annealing behavior between 300° and 950°C studied (by hardness and light and electron microscopy). It ulas inferred that the particles deformed with the lnatvix becoming lamellae which remained coherent. Comparison with published data fov pure nickel showed that aluminum greatly re-tavded softening and recrystallization, but it made little difference whether or not particles were present. The presence of pakticles led to a heterogeneous distribution of precipitates after annealing at 700" to 750°C. Recovery was not detected. Recrystallization occurred by the growth of new grains into unrecrys-tallized material. In a previous study by the author,' the growth of Ll2-type ordered yl(Ni3Al) precipitates was followed in Ni-12.7 at. pct A1 alloy as a function of aging at 600" and 700°C. The particles were showo to be cubical in shape in all sizes from 50 to 3000A and remained coherent. This work was used as a guide in preparing the starting structures for the present study of the effect of these particles on the annealing behavior of heavily cold-rolled strip. Another question of present interest was whether dislocation and particle hardening were additive, since the structures before rolling ranged from solution-treated to peak-aged to overaged. Also, precipitation might occur on annealing after cold-rolling. Reference may be made to other papers2"5 for previous work in this relatively unexplored field and only some recent work will be mentioned her:. phillips2 studied the effect of deformable 0 to 590A-diam cobalt particles on a Cu-3.23 pct Co alloy rolled 95 pct and found that the particles, which rolled out into thin lamellae, impeded softening and recrystallization. Tanner and servi3 likewise studied the annealing of cold-swaged Cu-2 pct Co alloy containing 150A-diam particles and found impeding effects. Haessner et a1.,4 on the other hand, found that incoherent 2-p-diam non-deformable particles of B4C (0.04 vol pct) tended to increase the rate of recrystallization of copper rolled up to 95 pct reduction. They attributed this to the formation of new grains at the particle interfaces. Humphreys and artin' found that nondeformable silica particles in copper rolled to 30 pct reduction accelerated recrystallization if the particle spacing was large and retarded it if the spacing was smaller. Haessner et a1 4 also studied a rolled Ni-Cr-A1 alloy; however, the particles of y'(Ni3Al)-type precipitate were not put in before rolling, but separated during the isothermal annealing at 750°C. No previous work appears to have been carried out on the effect of y' (Ni3A1) particles on the annealing of Ni-A1 alloy. Hornbogen and ICreye7 redetermined the solubility c of aluminum in nickel as a function of temperature T and showed that it was given by c = 32.6 exp(-1940/RT). This relation gives aluminum solubilities of 15.1, 14.2, 12.0, and 10.7 at. pct at 1000°, 900°, 700°, and 600°C, respectively. The phase precipitated from the nickel-rich solid solution is fcc y1 (Ni3A1) which has a Cu3Au -type ordered structure8 and remains ordered up to 1000°C.B EXPERIMENTAL PROCEDURE The alloy used was identical with that used before. Chemical analysis showed 6.27 wt pct (12.71 at. pct) Al, the principle impurities being 0.065 pct Fe, 0.022 pct Co, 0.020 pct Cu, and 0.004 pct C. Bar stock of 1 in. diam was cold-swaged to % in. diam, cold-rolled to 0.300-in.-thick strip, and annealed at 900°C in dry hydrogen. It was cold-rolled to 0.100-in. thickness and solution-treated for 1 hr at 1000°C while sealed in a quartz tube in argon, quenching in iced brine with the aid of a device to snap off the nose of the tube. Lineal analysis gave an average grain size of 0.055 mm. Pieces of strip were aged at 700°C in vacuo for 30 min, 51/4 hr, and 1 week to produce nominal average particle widths of 60, 150, and 500A, respectively, as known from the previous work.' The average diamond pyramid hardness was determined. The heat-treated strips were rolled from 0.100 to 0.005 in., a reduction of 95 pct, and the rolled strips stored at about -5°C. Small pieces were annealed within 1 week for 30 min at temperatures from 300° to 950° ±2°C in a horizontal vacuum furnace. Strips were withdrawn into a cooling zone, giving an estimated initial cooling rate from 950°C of about 50°C per sec. Average diamond pyramid hardnesses were determined on a lightly electropolished spot on the surface of each strip using 300-g load. Each point on the softening curves represents a separate annealed specimen. Sections containing the rolling direction were examined by optical metallography. Selected specimens were electrothinned to the center plane' and examined by transmission at 100 kv in a Siemens Elmiskop I electron microscope. It is well-known that changes in the structure tend to occur when a deformed strip is electrothinned below a thickness of a few hundred angstroms, although this is less serious with a material such as nickel which has a high melting point, and also is apt to be less serious when particles are present. Observations were nevertheless confined to thicker regions of the foils with estimated thicknesses over 1000A. No changes were observed due to beam exposure.

Jan 1, 1968

The 140th meeting* of the American Institute of Mining and Metallurgical Engineers was held in New York, Feb. 16 to 19, 1931. It consisted of the annual business session, twenty-six technical sessions at which 149 papers were presented, two round table discussions, two meetings of the Board of Directors, three meetings of Section Delegates, two formal lectures, four group dinners and 11 group luncheons, luncheon daily for members and guests, 20 committee meetings and conferences, the annual reception and dinner dance, an informal dance, a smoker-dinner, two meetings of the Woman's Auxiliary and a special program of entertainment for the ladies. Former members of the Rocky Mountain Club and friends lunched together at the Engineers Club on Tuesday. The proceedings of the Iron and Steel Division included four general technical sessions, an Iron Ore Round Table, the Howe Memorial Lecture, the Division luncheon at the Engineers Club Wednesday noon, a session each of the Executive Committee and the Committee on Nondestructive Testing, a luncheon each of the Committee on the Manufacture of Alloy Steel and the Blast-furnace Conference Group, and a dinner of the Committee on Physical Chemistry of Steelmaking. Dr. F. F. Lucas delivered the Howe Lecture, the title of which was "On the Art of Metallography." The Institute of Metals Division held three general sessions, its annual lecture, which was delivered by Dr. Arne Westgren and entitled "X-ray Determination of Alloy Equilibrium Diagrams," and a Division dinner at the Hotel New Yorker Thursday evening, at which Dr. G. W. Thompson was the principal speaker. The Executive Committee assembled at a luncheon on Thursday. A round table on Coal Land Valuations, a general technical session and a Division luncheon were held by the Coal Division. C. E. Bockus, President of the National Coal Association, made an informal talk at the luncheon which was held at the Engineers Club Monday noon. The Petroleum Division held six general sessions, including its annual production symposium. The annual dinner was held at the Engineers Club Thursday evening. A Gold Supply Symposium was the feature of the proceedings of the Committee on Mining Geology. This Committee also held a general session and a luncheon meeting. Sessions were held by other Technical Committees as follows: Mining Methods, 2; Mine Ventilation, 1 (besides which the Committee on Mine Ventilation Code held a meeting); Ground Movement and Subsidence, 1; Milling Methods, 1; Nonferrous Metallurgy, 1; Engineering Education, 1 (also a Committee luncheon); Non-metallic Minerals, 1, and Geophysical Prospecting, 2.

Jan 1, 1931

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell's business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.'s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell's business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.'s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

HenRy Clay FRick, a pioneer in modern coke and steel industry and, in more recent years, one of the outstanding financiers of America, died on Dec. 2, 1919, at his home on Fifth Avenue, New York. Although he had been ill since election day, when he had an attack of indigestion which developed into ptomaine poisoning, his death was a surprise to all. He is survived by his widow, Adelaide Howard Childs Frick; a son, Childs Frick, one unmarried daughter, Helen C. Frick, and four grandchildren. A quiet funeral service was conducted at the Frick home on Wednesday afternoon by the Rev. Dr. Leighton Parks, pastor of St. Bartholomew's Episcopal Church. This was attended by members and very intimate friends of the family, Trustees of the Metropolitan Museum of Art, Officers of the Links Club, and Directors of the United States Steel Corpn. Henry Clay Frick was born Dec. 19, 1849, in West Overland, Westmoreland Co., Pa. His father, John W. Frick, was a farmer of Swiss ancestG, and his mother, Elizabeth Overholt Frick, a member of an old Mennonite family. Until he was sixteen, he spent his time at school, on his father's farm, and in his grandfather's distillery, where he kept books. He attended Otterbein University, in Ohio, for a year. Frick, learning that coke was an essential of the already rapidly developing steel business, early invested every cent he could get in coking-coal lands. With the help of an associate of his grandfather, he formed the corporation of Frick & Co., coke dealers, and acquired fifty-one ovens in the Connellsville region and 300 acres of soft-coal lands. During the panic of '73, with the help of Judge Thomas Mellon, a Pittsburgh 'banker, he bought out his partners and while coke was selling at 90 cents a ton enlarged his purchases of suitable lands. Later, the price of coke increased until it was selling at $5 a ton. Before he was 30 years old, Frick was rated a millionaire. Association with CaRnegie In 1878, he sold an interest in the business Do E. M. Ferguson of New York, and later a share to Mr. Ferguson's brother. Four years later the business was reorganized into the H. C. Frick Coke Co. with vast coal lands, great banks of ovens, and a capitalization of $2,000,000. Then began his association with Andrew Carnegie. He exchanged a part of his coke interest for shares in Carnegie Brothers of Pittsburgh,

Jan 1, 1920

By P. A. Witherspoon, S. P. Neuman

Evaluating the permeability of a caprock overlying a potential gas storage reservoir is a very critical problem. Pumping water from the reservoir can be used as an evaluation tool in analyzing this problem. Fluid level changes that occur in the aquifer us well as in the caprock can be measured with appropriately placed wells. If the leakage of water from the caprock into the aquifer is considerable, the effects will be apparent in the aquifer. If the leakage is slight, however, it will not be possible to detect it with certainty from observations in the aquifer alone. Fluid level measurements in the caprock must be relied upon. and improved methods of analyzing such effects have been developed which are based on a theoretical analysis of fluid flow through a caprock of infinite thickness. An example applying these methods to field data is discussed. INTRODUCTION One of the most critical problems in evaluating an aquifer gas storage project is determining the tightness of the caprock overlying the formation to be used as the storage reservoir. A formation that has previously held oil or gas obviously has a suitable caprock, but an aquifer that contains only water gives no such assurance. A number of aquifer projects in the United States have been troubled by gas leaking out of the intended storage zone, and the ensuing difficulties have led to the development of new evaluation methods. One of these new methods is pump testing wherein water is removed from the aquifer at some controlled rate prior to injection of gas. This fluid withdrawal causes a pressure drop to move out through the aquifer for considerable distances in a matter of days or weeks. Depending on the properties of the caprock, a pressure transient can also pass upward (as well as downward) through the caprock layers adjacent to the aquifer. Thus, if the operator has placed observation wells at appropriate distances from the pumping well, the rapidity with which the pressure transients reach different points in the system can be used to investigate the fluid transport properties of both the aquifer and its caprock. The usefulness of pump testing has been recognized by groundwater hydrologists for many years as a means of determining the potential yield and properties of aquifers used in water supply They have introduced the term "leaky aquifer" for a system in which an aquifer is overlain (or underlain) by semipermeable caprock layers. The ease with which water leaks into the aquifer during pumping can, of course, be very beneficial in bringing additional water to the pumped well. Hydrologists have therefore devoted considerable attention to this prob-lem. From the gas storage standpoint, however, the tighter the caprock layers that overlie the intended storage reservoir, the better are the conditions for minimizing or eliminating any vertical migration of gas. Thus, after a suitable geologic structure has been found, the emphasis in aquifer storage projects is in determining that the caprock is tight. Attention has recently been focused on the use of pump testing as one approach to solving this problem.23,24 This paper presents a further development on evaluating the permeability of a slightly leaky caprock when the caprock is of infinite thickness. From the practical standpoint, this means that the caprock layers are thick enough that pressure transients do not reach the outer boundaries of the system during the pumping test. In a subsequent paper, an analysis of the case where the caprock is of finite thickness will be presented. PREVIOUS WORK ON LEAKY AQUIFERS Jacob" developed a partial differential equation describing the flow of water in an aquifer of permeability k that is overlain by a leaky caprock of permeability k'. Fig. 1 shows a schematic cross-section of the system under consideration. One of his principle assumptions was that if k > > k', the direction of flow is essentially vertical in the caprock and horizontal in the aquifer. Neuman19 confirmed the validity of Jacob's assumption using a mathematical model. Another assumption was that a permeable source layer overlies the caprock (Fig. 1) and is able to maintain a constant hydraulic head at the upper boundary of the caprock. By neglecting the effects of compressibility within the caprock, Jacob1* developed a solution for a bounded circular aquifer. Later, Hantush and Jacobx5 used the same assumptions to solve the case of an infinite radial aquifer that is pumped at a constant rate. Their solution may be expressed in di-mensionless parameters by

[ ]

Jan 1, 1938

By Robert M. Dreyer

AGGREGATE With an annual domestic production of over 1.6 billion tons at a value of over $2 billion (see Table 15.1.1), the production of aggregate (crushed rock, sand, and gravel) is a basic industry of utmost economic importance. Because of the role of aggregate materials as essential ingredients of concrete, asphalt surfacing, and plaster, their delivered prices are major factors in determining the cost of construction. The annual domestic production comes from nearly 10,000 plants. About 15% of these plants account for over one-half the production. In a rapidly inflating economy, the average mine sales price of aggregate has remained relatively stable. The actual mine sales prices, however, vary greatly depending on quarrying costs in various parts of the country. Of much more importance in construction costs, however, is the delivered price of aggregate. This varies for each job, depending on the distance from the quarry and resulting transportation costs, as well as the initial cost at the mine. Because of a proliferation of regulations limiting new quarries in the vicinity of the encroaching urban sprawl, the average distance which aggregate must be transported has been increasing rapidly. Although it is impossible to derive an average delivered cost for aggregate, it should be noted that even an increase of only $1 per ton in average delivered cost over the last decade (probably a minimal assumption) would mean an annual cost $1.5 billion higher than ten years ago. In recent years, structural engineering considerations, as well as an increasing use of lightweight concrete blocks, have resulted in a rapidly increasing demand for lightweight concrete and plaster, the essential ingredient of which is lightweight aggregate. Principal lightweight aggregates are: pumice, slag, perlite (thermally expanded hydrous volcanic glass), vermiculite, and expanded shale, formed by the thermal expansion of shale and slate. The United States now has the capacity to expand, annually, over 13 million tons of shale and slate and to expand over 600,000 tons of perlite. In locating a site for aggregate production. the following factors must be considered: (1) tonnage available; (2) quality of aggregate (including local variations); (3) distance from major use areas; (4) transportation costs, including those resulting from present and possible future haulage restrictions; (5) zoning regulations; (6) operating costs, including the cost effects of compliance with local regulations governing blasting, air pollution, water pollution and drainage, noise levels, and operating periods. At one time, locating a suitable site for the production of crushed rock, sand, or gravel, in most areas, was regarded as an extremely simple task. In the past few years, however, finding a site for profitable production of aggregate has assumed ever-increasing com-

Jan 1, 1976

By Henry Emmett Gross

Two types of decline curves are considered and their applications are discussed. The first is the well-known semilogarithmic decline curve having the rate of production plotted on the logarithmic scale and the time on the horizontal scale. The other curve is the percentage of oil in the fluid versus cumulative production, and it is plotted on Cartesian coordinate paper. These curves are illustrated by carefully and adequately labeled graphs. Where conditions permit application of both types of curves for rationally determining the reserves of a well, both should be applied and the most conservative reserve should be chosen. Formulas are given for determining the economic limits. For a semi-l~~arithmic~decline curve the formula is: A = B X C X D X E X F or B = A/C ? D X E X F A = total monthly operating cost (average of past year), B = economic limit in barrels of oil per day, C = days in an average month = 30.4, D = market price of crude per barrel, E = 1-royalty, F = 1-gross production tax, G = water production in barrels per day at the economic limit, H =per cent oil in fluid at economic limit. The economic limit for a per cent oil in the fluid curve is: H = B/B+G X 100 The semilogarithmic decline curve is treated first. Straight-line extrapolations on semilogarithmic paper follow the compound interest compound discount law, hence the ensuing formulas derived from this law may be used in computing reserves for such extrapolations: [1___1/(1+Y)]

Jan 1, 1939