Search Documents

By I. C. Edwards, G. E. Agar

INTRODUCTION Many research efforts over the past years have been devoted to the study of energy consumption in comminution and the characteristics of the broken material. The old "laws" have been superseded by more general methods of analysis1,2,3 but these methods have not received much attention outside the laboratory. The work to be described here was done in order to obtain scale-up information on wet rod milling of sylvinite. EXPERIMENTAL A 30 x 51 in. Denver rod mill with a scoop feeder was used for these tests. Ore was fed from a variable speed screw conveyor into the feed box along with saturated brine. The mill was filled to approximately 45% of its volume with 2400 lbs of a mixed rod charge. The minimum possible feed rate was 2.5 tph and the practical maximum for this mill was 8 tph. Individual tests were run by setting the solid feed rate, then adjusting the brine flow rate to give the desired pulp density. After steady state, as evidenced by constant discharge pulp density, had been reached, samples of the discharge were taken at 15-minute intervals. These samples were filtered, washed with alcohol, dried, then screened on Tyler screens using a Ro-tap shaker. The sylvinite feed was regular plant feed that had been scalped at 20 mesh and was tapped from the coarse ore bins. It had been previously passed through a roll crusher set at 3 inches and after scalping was essentially minus 1 in. plus 20 mesh. RESULTS The screen analysis of samples from each series of tests was plotted on double logarithmic scale paper to determine the reliability of the series. In some cases, a faulty sample or screening procedure dictated that the results of one test be discarded. The criterion is a simple one — if the slope of one plot was noticeably different from the others in the series, it was discarded. The only cases that caused difficulty were those in which the brine was not thoroughly displaced from the solids. When this occurred agglomerates were easily identified on the screens and the whole of the sample was retained on 3 or 4 screens. There were no border line cases. The number N given in Table 1 is the number of size analyses that were pooled to form the data shown in Fig. 1. While examining the reliability of the sizing and sampling by plotting the data, it became apparent that there was no significant difference between grinds made at 50 and 60% solids. For the analysis given here, these tests were regarded

Jan 1, 1967

By L. D. Jaffe

IN previous metallographic work on titanium and its alloys, difficulty has been encountered in distinguishing spheroidal particles of titanium hydride, dispersed in a-titanium, from other phases that may be present, such as p-titanium. This problem is common in examination of commercial unalloyed titanium.' In the course of an investigation of the Ti-H phase diagram, it was noted that titanium hydride, dispersed in a matrix of a-titanium, showed strong optical anisotropy when examined under polarized light. With sensitive tint illumination, particles of the hydride, when the stage is rotated, changed from bright yellow to bright blue in color. Since P-titanium is cubic, it showed no color change on rotation, remaining dark gray or blue-gray. Although a-titanium is hexagonal, it showed only a minor color change, going from pale pinkish-blue to pale purplish-blue. These colors could be modified somewhat by adjustment of the illumination. They were observed in specimens mechanically polished, both without etching and after etching with hydrofluoric acid-nitric acid mixtures in either water or glycerine. The strong color change of the hydride seems to offer a simple method for its metallographic identification. Optical anisotropy of titanium hydride is inconsistent with its accepted face-centered-cubic structure.' Samples of iodide titanium containing 6 to 40 atomic pct deuterium were prepared for diffraction studies. After deuterating and slow cooling' the samples were held 21 % hr at 400 °C, water quenched, held 61 hr at 100°C and quenched, then held 64% hr at 255 C and quenched. Debye ex-posures with MoKa X-rays and 1.111A neutrons were made at room temperature of samples as-deuterated and after the 100" and 255°C treatments. Table I shows the lines observed, in addition to those attributable to a-titanium. These data show that the hydride phase was not cubic, but probably tetragonal. The titanium atoms appeared to form a body-centered-tetragonal lattice complex, two titanium atoms per cell, with approximate dimensions: a = 3.12A, c = 4.18A, and c/a =1.34A. This is equivalent to a face-centered-tetragonal complex, four titanium atoms per cell, with approximate dimensions: a = 4.42A, c = 4.18A, and c/a - 0.946A. The presence of the 2.98 and 1.81A neutron lines indicates that the true Bravais lattice is not identical with this lattice complex, but may be primitive tetragonal with dimensions some multiple of those of the complex. The relative intensities of the hydride and a-titanium X-ray lines as functions of overall composition indicated that the hydride, presumably in equilibrium with the a at 100" to 255"C, contained more than 62 atomic pct H. Acknowledgments The experimental work covered in this report was done at Brookhaven National Laboratory, through the courtesy of D. Gurinsky. The cooperation of J. Sadofsky, 0. Kammerer, A. McReynolds, and A. Cendrowski is gratefully acknowledged.

Jan 1, 1957

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By H. Warlimont

In recent investigations of the microstructure and crystallographic features of martensite by electgon microscopy,', '9 thin films (about 50 to l000A in thickness) have been used as specimens. It was found by W. Pitschl ,2 that the lattice relationships between the supefiaturated fcc matrix and the martensite formed in thin films were different from those observed after transformation in bulk material. Corresponding differences are to be expected in nucleation and in reaction kinetics in the formation of martensite in thin films, but have not yet been reported. In the course of the preparation of thin films of iron-base alloys for investigation by electron microscopy it was observed that films of alloys, whose martensite formation temperature (Ms) was below room temperature, formed martensite during the electrochemical thinning process conducted at or above room temperature. The chemical compositions and approximate bulkM,-temperatures of the three materials on which this observation was made are listed in Table I. The alloys were vacuum-melted from high-purity metals. It can be seen that the effect occurred in alloys that contain only sub-stitutional components as well as in alloys that contain carbon as an interstitial solute. The appearance of martensite formed in this manner is illustrated in Fig. 1, which represents a polished film of alloy No. 1 at XI0 magnification. The martensite plates can be recognized by their surface relief effects. In addition, heavily strained (owrinkledo) austenite can be seen near the edges of the film where it is thinnest and transformation stresses or strains can be accommodated by plastic deformation most easily. The nonuniform distribution of transformed regions is probably due to the varying thickness of the film. These observations were common to all materials listed in Table I. Because effects of supercooling or straining can

Jan 1, 1962

By Stanislaus Skowronski

OVERPOLED copper, as commonly defined, is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such copper is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a Well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, Which enables copper to be cast free from blowholes. It seems that When oxygen is present, other gases are less soluble in molten copper; When oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, Which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of Wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, While an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen, and the effect of this action. on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulphur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 3, 1918

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.' In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors' attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963

By Eugene Stephenson

CRITICAL analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,1 Pierce and Lewis,2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or, by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by McWilliams.4 Much of the. dissatisfaction with proration in certain fields is because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the "potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If :no difficulties ever

Jan 1, 1931

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By A. T. Miesch, L. B. Riley

Distribution of minor elements in sandstone-type uranium deposits of the Colorado Plateau is being studied by the USGS on behalf of the A EC. A primary objective has been to provide basic data which could be useful in geo-chemical exploration for new deposits. The basic statistical measures — similar to those used in sedimentary petrology—are described. The underlying principle is that the frequency distributions fit or approach the log-normal form. Since 1952 the U. S. Geological Survey on behalf of the U. S. Atomic Energy Commission has conducted a study of the distribution of minor elements in sands tone-type uranium deposits of the Colorado Plateau. A primary objective in this study has been to provide basic data which could be useful in geo-chemical exploration for new deposits. Among the basic data considered important are estimates of the abundance and habit of each element in the ore and in the host rocks. It has been found that a few basic statistical techniques, and variations of these techniques, are useful in this type of study. Some of the basic techniques have been used to advantage by researchers in geochemistry and in other fields of geology, especially sedimentary petrology; others have been used to only a limited extent. Among the latter is the linear correlation coefficient, which has proved useful in assessing the element associations in a particular rock type without analysing individual mineral separates. In computing the basic statistical measures a scale has been used which is, in some ways, similar to the phi ($) scale used by sedimentary petrol-ogists in grain-size studies.' FREQUENCY DISTRIBUTIONS It has been recognized for some time that the results of analyses for a given minor element in a suite of samples of rocks or ores yield frequency distribution curves which are approximately normal when the curves are plotted on logarithmic or geometric scales. In other words, the analytical results give an approximate lognormal frequency distribution. A classical example is given by D. G. Krige2 in the study of the distribution of gold values from a mine on the Witwatersrand. Another example is shown in Fig. 1, the distribution of barium concentrations in samples of uranium ore from the Chinle formation. The geochemical data are analogous to grain-size data gathered by the sedimentary petrologist. Both types of data, after simple logarithmic transformations, may be treated by conventional statistical methods based on the normal distribution. This is not to say that other types of transformations may not serve equally well or better for particular element distributions.3 Spectrographers and other analysts are quite aware of the dependence of their precision on the concentration of the element present.4 For example, in the part per million range the variation may

Jan 1, 1961

Jan 1, 1967

By N. A. Gjostein

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By K. C. Mills, E. T. Turkdogan

A number of investigators1 6 have noted the presence of a liquid miscibility gap in the Fe-Sn binary system. However, the first attempt to measure the

Jan 1, 1964

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By L. Moyd, P. Moyd

The first commercially available portable gamma ray-neutron beryllium detector, the Rerylometer, was developed by the same group that developed the first practical portable scintillation counter, the Scintillo-meter. This group includes Professor George Brownell, of the Geology Department of the University of Manitoba in winnipeg, and his associates, K. I. Roulston, R. w. Pringle, and R. L. Funt, of the Physics and Engineering Departments of the University of Manitoba. A prototype model was tested in the field by Dr. Brownell during the summer of 1958. Commercial production was undertaken shortly thereafter by Nuclear Enterprises Ltd., of Winnipeg, and a license for manufacture and distribution in the U.S. was granted to Isotopes Specialties Co., of Burbank, California, a division of Nuclear Corporation of America. Early in 1959, we were retained by the 'Mining Division of Minerva Oil Co. to Legin a search throughout North America for minable deposits of beryllium, and to train members of their permanent staff to continue the program. The project included literature sur-veys, interviews with members of various federal, state, and provincial agencies, scanning of our own collection of suites of specimens from various mineral occurrences, and the examination of deposits in the field. The value of a beryllium detector to this program was obvious and arrangements were made to procure one as soon as possible, which resulted in our obtaining and using the first instrument that was produced commercially in the U. S. In addition to the commercially available Berylometer, Mr. William Vaughan and his associates, of the U. S. Geological Survey Geophysics Division, in Denver, have developed and tested several experimental instruments based on the same principles. DETECTOR Principles The detection of beryllium is based on the fact that "hard" gamma rays (1.6 MEV and geater), such as those produced by Antimony convert ordinary beryllium (Be9) to Be8 , with the release of a neutron. The neutrons are counted by a scintillator designed to favor neutron responses while suppressing those of gamma rays. 'The instrument is completely selective for beryllium. No other element can interfere. Instrunlentation The Rerylometer itself, which is cylindrical, is about 8 inches in diameter, 13 inches high, and weighs about 11 pounds. (Figs. 1, 2). The principal components include: 1. A disc of wax to moderate (or "thermalize") neutrons. 2. A boron-enriched polyester-zinc-sulphide fluorescent screen. This material produces strong flashes when struck by thermalized neutrons but only weak flashes from gamma rays. 3. A photomultiplier tube. 4. An electronic circuit, complete with one srnall 71/2-volt dry battery. The photomultiplier tube and electronic circuit convert neutron flashes to electrical impulses, but gamma ray effects are almost

Jan 1, 1961

By Edward L. Beutner, Robert M. Crump

Benson Mines low-grade iron ore reserve is a replacement deposit within the Grenville gneisses of the Adirondacks. The average grade of the crude ore is about 23 per cent iron. The iron minerals are principally magnetite and hematite disseminated throughout the gneisses as discrete grains about 1 mm in size. Both the ores that are beneficiated by magnetic means and the non-magnetic ores that are treated by a gravity method of concentration are found in stratigraphically different positions but are mined from one open pit, which is about 2.5 miles long and 800 feet wide and are treated separately. The gneisses are described and named according to the distinctive mineralogy of each. Recognition of the gneissic types permits the interpretation of the structure as a northward-plunging syncline overturned to the west. A large subsidiary anticline-syncline complex occurs on the east limb of the major syncline. Iron minerals in sufficient quantity to be considered ore are confined to areas where the footwall rock has been overturned to become the hanging wall.

Jan 1, 1968

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By B. M. Larsen, J. W. Campbell

Several articles have recently been published discussing the conditions necessary for accurate measurements of temperatures in the open-hearth steel furnace. In the course of a study of refractories service conditions in steel furnaces, the present writers have taken temperatures in several open-hearth shops in the Pittsburgh district. The conclusions, as to conditions necessary for accurate measurements of temperature, are somewhat at variance with those of other investigators. The subject is closely connected both with the close control of steel-making and the prevention of overheating of the silica refractories used in roofs and walls. It is becoming more and more important to obtain furnace temperatures of fairly definitely known accuracy. At present, the most useful instrument for such measurements is the disappearing-filament type of optical pyrometer. This method of measurement has formed the basis of most other discussions on the subject and was also used by the writers. Previous Investigations In 1916, Burgess' made perhaps the first systematic series of measurements in steel furnaces. The emissivity figures of 0.40 for liquid steel and of 0.53 to 0.65 for liquid slags had been determined by the Bureau of Standards and were used by Burgess in this work. These correction factors are still being used and are regarded as fairly accurate, so that the tapping and teeming temperatures on metal streams given by Burgess should be very nearly correct. Most of his temperatures of furnace roofs and slag surfaces were taken while flames were present in the furnaces and include a few roof temperatures above 1700' C. (3100' F.).

Jan 1, 1927

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930

By R. H. Widmyer, G. M. Wood

This investigation was prompted by the absence of a simple, accurate method to predict optimum second stage separation pressure in three stage separation operations. Three stage separation as used here includes two separators plus the stock tank. The first stage pressure is usually fixed by gas sales conditions and the third stage is at atmospheric pressure. Thus, the second stage pressure is the only one that may be varied in-discriminantly during production operations. No variations in temperature were considered in this study, even though it will vary among systems, for a change in temperature has little effect on the optimum pressure. Optimum pressures may be determined from flash calculations, but these are tedious unless a computer is available. An early attempt to develop a simpler method&apos; yielded an equation which gave the optimum pressure only as a function of initial and final pressure. Experience, however, confirms theoretical relationships which show that composition as well as pressure and temperature must be a factor. This indicates that the basic relationship should be an equation of the form, where P, is second stage pressure, P, is first stage pressure, A is a function of P. (stock-tank pressure) and the system composition, and n is a function of the number of stages and the system composition. Fig. 1 shows the basic variation of P2 with P for a fixed system composition. A series of such figures clearly showed the effect of composition. The peak of each curve reflects that second stage pressure at which the stock-tank recovery (gal/MMcf) residue gas is a maximum value. DEVELOPMENT OF NEW CORRELATION Wellstreams having 17 different analyses, ranging from low gravity crude to condensate, were used to determine the effect of composition. Each wellstream was flashed through three stages to determine the optimum second stage pressure for each first stage pressure. Equilibrium vaporization ratios proposed by Latham and Campbell were used throughout. The heptane plus fraction, for simplicity, was assumed to have the properties of octane. The results were subjected to an empirical analysis in an attempt to develop a correlation- that would be (1) simple, (2) accurate, and (3) eliminate the need for any flash vaporization calculations. This analysis yielded two equations, one for wellstreams having a specific gravity greater than one (air = 1.0) and one for those less than one. For crude streams (specific gravFor condensate (specific gravity < 1.0),