Search Documents

Page Bronze Bearing Metals. By G. H. Clamer............... 162 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. Waring .. 166 The Tin-plate Industry. By D. M. BUck. Discussed by G. H. ClameR, J. W. RICHARDS............................ 168 The Aluminum Bronze Industry. By W. M. Corse............ 171 Bronzes, Bearing Metals, and Solders. By G. K. BURgess and R. W. Woodward. Discussed by G. H. Clamer, R. T. Roberts......... 175 Babbitts and Solder. By G. W. Thompson................ 184 The Cadmium Supply of the United States. By C. E. Siebenthal. Discussed by M. L. Lissberger, C. W. Hill, F. F. ColcoRd.......... 185 Solder, Its Use and Abuse. By M. L. LissbergeR............ 192 Bronze Bearing Metals G. H. ClameR,* Philadelphia, Pa.—Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early days, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 1, 1919

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss's original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss's original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200°C, a wide range of conveyors is available. Special constructions of rubber conveyor belts. steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400°F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F.

Jan 5, 1953

By G. H. Clamer

Page Bronze Bearing Metals. By G. H. Clamer............... 162 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. Waring .. 166 The Tin-plate Industry. By D. M. BUck. Discussed by G. H. ClameR, J. W. RICHARDS............................ 168 The Aluminum Bronze Industry. By W. M. Corse............ 171 Bronzes, Bearing Metals, and Solders. By G. K. BURgess and R. W. Woodward. Discussed by G. H. Clamer, R. T. Roberts......... 175 Babbitts and Solder. By G. W. Thompson................ 184 The Cadmium Supply of the United States. By C. E. Siebenthal. Discussed by M. L. Lissberger, C. W. Hill, F. F. ColcoRd.......... 185 Solder, Its Use and Abuse. By M. L. LissbergeR............ 192 Bronze Bearing Metals G. H. ClameR,* Philadelphia, Pa.—Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early days, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 1, 1919

R. W. Guard (General Electric Co., Schenectady)— The method of fractional replication discussed by the author has proven very valuable to us in applied research connected with alloy and process development where many of the same experimental difficulties exist. Several of our experiences may be of assistance to those who want to apply the method in these fields. Contrary to the author's observation that interactions are rarely significant, we have found in a number of cases that first order interactions exist which are significant and metallurgically important. Because of this difference there are two further precautions which should be taken in order to minimize the difficulties from this point. First, in evaluating the importance of

Jan 1, 1957

By J. McLaren Forbes

Geologists and engineers in charge of diamond drilling often have no practical experience in the work, yet they must direct the drillers. In discussing some of the problems that arise, the author of this paper has tried to remember the things he did not know about diamond drilling when he first came in contact with that work. The basic reason for most diamond-drill holes is to obtain information. The more thorough the understanding of the geological and engineering problems involved, the greater will be the benefit derived from a drilling program. One of the best methods to ensure some thinking before drilling is to record on the permanent drill log, before the hole is collared, the reasons for the work and the information desired from that particular hole. When the hole is finished, the information obtained should be recorded. Driller The choice of a diamond driller is very important. If no experienced driller is available, a competent miner who has a sense of responsibility and better than average mechanical ingenuity can do the work. The best answer to most practical drilling problems, from the standpoint of the person in charge of the drilling program, is the service of experienced diamond drillers or drilling firms. Equipment Drilling equipment should be adequate to put down the longest hole desired and handle the toughest ground encountered. The type of bit used depends upon the ground drilled. Experimenting with various bits and careful study of footage records are the best means of determining which to use. Under ordinary circumstances it is best to drill using an EX barrel when possible. The length of rod and core barrels that can be used depends on the size of the drill station. Also, the length of core barrel depends on the way the ground cores. In good ground as much core will be recovered with a 10-ft. barrel as with a shorter one, and with considerable saving of drilling time. A water pump is needed if the hole is so deep that the water pressure is not strong enough to wash out the cuttings, or if it is drilled at an angle that prevents full force of the water pressure. Instructions For an Inexperienced Driller 1. Never run a bit too long a time. When a bit seems to be "good for one more run," discard it. 2. Always let the rods down on bottom easily. Protect the bit from sudden shock. 3. Start the drilling slowly and easily. Do not put pressure on the bit too fast. Diamonds can break. 4. Be sure the water pressure is strong enough to clear the bit, but do not use more water than is needed, as it may wash away the core. Usually, if no core is recovered the hole is a total loss. 5. When dry-blocking, do not run without water longer than necessary as the bit may burn. 6. Be sure the rods are well caulked and tightly screwed together. If not well caulked they will lose water, and if not

Jan 1, 1946

CONTENTS PAGE Ross, J. M. and WAYLAND, R. G.-Mining Methods at the Homestake. Discussed by Benjamin F. Tillson, R. M. Raymond, I, H. Barkdoll, Arthur Notman 1 EMMEL, RUDOLPH.-Mining Methods in Zaruma District, Ecuador. Discussed by Rudolph Emmel, George A. Packard, Fred Hellmann, R. M. Raymond, Arthur Notman 2 MISHLER, R. T. and BUDROW, L. R.-Methods of Mining and Ore Estimation at Lucky Tiger Mine. Discussed by Fred Hellmann, Benjamin F. Tillson...4 PARK, JOHN FURNESS.-Mining Methods of Jarbidge District. . Discussed by R. S. Lewis : 5 Mining Methods at the Homestake Discussion of the paper of A. J. M. Ross and R. G. WAYLAND, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1408-A, with MINING AND METALLURGY, February, 1925. BENJAMIN F. TILLSON, * Franklin, N. J.--It requires a good deal of timber to operate, especially the caving systems. An important function in mine operations now seems to be forestry and to operate a timber tract in order to insure a supply of timber. By depleting the timber resources of your section, you only increase your costs later when timber must be brought in from the Pacific Coast or the East. Our experience has been that any square-set method of timbering is the most expensive. Timbering for stoping systems, top slicing if you will, although it uses a large volume of time does not require as expensive timbering as the square-set method; also it does not require as long a life for-the timber, so that such wood as birch and maple, which have strength but not long life under the fungus conditions in the mine, may be used. All the drifts in the orebody are thoroughly timbered, and it has required a lot of timber. If we had it to do over, we would spend a lot more money in the development of rock drifts; as a matter of fact, we must ultimately come to that any way.

Jan 6, 1925

THIS chapter and Chapter 19 deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the first two laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only: 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the heat balance of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced. The cause probably lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities in flow distribution and air leakage present in any real open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot- metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million Btu per net ton of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million Btu and the sensible heat in the preheated air at the port ends is 117 million Btu, so that the total heat input at the ports is 477 million Btu. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million Btu, but 120 million of this is supplied by the heat in the hot metal and by various heat-evolving reactions in the bath,

Jan 1, 1951

By Gilbert Soler

Page Introduction. By Gilbert Soler.........................657 Deoxidation of Basic Open-hearth Steel. By T. S. Washburn.............658 Slag-metal-oxygen Relationships in the Basic Open-hearth and Electric Processes. By J. S. Marsh. (With discussion)...........................672 The Total Oxygen Content of Plain Carbon Open-hearth Steel during Deoxidation and Teeming. By Michael Tenenbaum and C. C. Brown. (With discussion)......685 The Occurrence of Oxygen in Liquid Open-hearth Steel—Sampling Methods. By T. E. Brower and B. b. Larsen..........................712 Effect of Deoxidation on the Strain-sensitivity of Low-carbon Steels. By H. K. Work and G. H. Enzian. (With discussion)........................723 The Relation among Aluminum, Sulphur, and Grain Size. By C. E. Sims.......734 Some of the papers and discussions that appear on the following pages were presented at the meeting of the Iron and Steel Division in Cleveland, Ohio, on Wednesday, October 18, 1944. with L. F. Reinartz and H. K. Work as Chairmen; the remainder were scheduled for the New York Meeting of the Institute in February 1945, which was canceled.

Jan 1, 1945

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By John B. Dilworth

In September, 1930, H. N. Eavenson, then Chairman of the Coal Division, appointed a Committee on Methods of valuing Coal Propelvties, with John B. Dilworth as chairman. The latter prepared a schedule' of features for consideration under the general headings of Undeveloped and Developed Coal Properties. These subjects were divided among the members of the committee and during the next year written discussions of his allotted subjects were received from each member. Mr. Grimes and Mr. Eavenson discussed the entire list,. These discussions were mimeographed and a set sent to each member before the meeting of the Institute in February, 1932. There was a general discussion at that meeting. At the meeting in February, 1934, Mr. Dilworth submitted a report12 which summarized the accumulated opinions and data and presented the conclusions of the committee as a whole on the subjects embraced in it's schedule. Members of the committee expressed the desire that some of the individual opinions be published for reference. Mr. R. Damon Hall's abstracts of these papers arc therefore presentrd herewith.3 Personnel of Committee John B. Dilworth (Chairman), Consulting Mining Engineer, Edward V. D'Invilliers Engineering Co., Philadelphia, Pa. Eli T. Conner, Consulting Mining Engineer, Seranton, Pa. W. G. Duncan, Jr., Superintendent, W. G. Duncan CoaI Co., Greenville, Ky. Howard N. EAveNson, Consulting Mining Engineer; Eavenson, Alford & Hicks. Pittshurgh, Pa. George Watkin Evans, Consulting Mining Engineer, Seattle, Wash. J. A. Garcia, Consulting And Constructing Engineer, Allen & Garcia Co., Chicatgo. III. John Alden Grimes, Valuation Engineer, Bureau of Internal Revenue, Washington, D. C. Otto Herres, Assistant Manager, United States Fue1 Co., Salt Lake City, Utah. J. R. Hicks, Consulting Mining Engineer, Eavensorl, Alford & Hicks, Pittsburgh, Pa. Robert D. Reeder, Mining Engineer, U. S. Bureau of Mines, Washington, D. C. Samuel, A. Taylor, Consulting Engineer, Pittsburgh, Pa. Bleeckee L.. WHeeler, Mining Engineer, Ford, Bacon & Davis, New York, N. Y.

Jan 1, 1934

A New Microscopy and Its Pntentialities. By Charles S. Barrett. (Metals Technology, .April 1945) Physical Metallurgy Fundamental Principles Involved in Segregation in Alloy Castings. By R. M. Brick. (Metals Technology, Sept. 1944) A Stud) of Age-hardening Using the Electron Microscope and Formvar Replicas. By D. Harker and MI J. MurphyI (Metals Technology, June 1945) Standards for Identifying Complex Twin Relationships in Cubic Crystals. By C. G. Dunn. (Metals Technology, April 1945) Orientation Changes during Recrystallization in Silicon Ferrite. By C. G. Dunn (Metals Technology, April 1945) The Orientation Texture at the Surfacr of Cast RIetals. By Gerald Edmunds. (Metals Technology, Jan. 1945) (With discussion) Internal Friction of Single Crystals of Brass, Copper and Aluminum. By George H. Found. (Metals Technology, June 1945) (With discussion) Recrystallization of Aluminum in Terms of the Rate of Nucleation and the Kate of Growth. By W. A. Anderson and R. F. Mehl (Metals Technology, Feb. 1945) (With discussion) Copper and Copper-rich Alloys Textures, Anisotropy and Earing Behavior of Brass. By F. H. Wilson and R. ill. Brick. (Metals Technology, June 1945) (With discussion) Phantom Laminations in Brass. By Daniel R. Hull, H. F. Silliman and John R. Freeman, Jr. (Metals Technology, Jan. 19451 (With discussion) Corrosion of Yellow Brass Pipes in Domestic Hot-water Systems—a Metallographic Study. By E. P. Polushkin and Henry L. Shuldener. (Metals Technology, Oct. 1944) (With discussion) The .Alpha Solid Solution Field of the Copper-manganese-zinc system. By R. S. Dean, J. R. Long, T. R. Graham and .%. H. Robersori. (Metals Technology, June 1945) A White High-manganese Brass. Ry K. S. Dean, J. R. Long, T. R. Graham and C. W. Matthews. (Melds Technology, June 1945) Magnesium Alloys Oxidation Inhibitors in Core-sand Mixtures for Magnesium Castings. By O. Jay Myers. (Metals Technology, Feb. 1945) (With discussion) Grain Size and Properties of Sand-cast Magnesium Alloys. By R. S. Dusk and C. R. Phillips. (Metals Technology, Feb. 1945) (With discussion) Rater Quenching of 'Some Typical Magnesium Casting Alloys. By R. S. Busk and R. E. Anderson (With discussion)

Jan 1, 1945

By James Boyd

In critical times such as the present, when the whole world is agitated by the aftermath of war and the road to peace is blocked by seemingly insurmountable obstacles, it is fitting that we should pause to take inventory of the material resources essential to our national security. Our status as a world power, in peace as well as in war, is intrinsically bound to the availability of minerals, for the foundation of our industrial and economic structurewhich in turn largely determines our military potential and our limits of national prosperity-rests on our ready access to economic sources of iron, copper, lead, zinc, manganese, bauxite, and at least threescore of other metals, minerals, and mineral fuels. By applying the well-known facts of mineral resources to recognized fundamental concepts of preparedness, we can obtain a- clearer picture of the essential needs of our country. Historically, the lure of minerals and other raw material resources has all too frequently led nations to policies of imperialism and war. For more than a century the staking of colonial territory for new sources of raw materials has been a primary objective of many nations. These national policies. of aggrandizement were accelerated by increasing industrialization. The nations, in their aggressive search for

Jan 1, 1948

By Frank C. Smith

The following article covers the history of a metallurgical campaign, commenced in March, 1905, at the mines of the Socorro Bold Co., in the so-called desert region of Yuma county, Arizona. The results obtained were simply a function of necessity, as will be seen from the description of the local economic conditions and the character of the ores treated. The mines and mill of the Socorro Gold Co. are located near the small village of Harrisburg, about 60 miles from Congress Junction, Ariz., which, at the time this work was undertaken, was the nearest railroad station, and from which all supplies were brought by wagon through the desert, at a cost varying from $10 to $15 per ton in addition to the railroad freights. Wood, the only available fuel, cost $7 per cord. Water for all purposes was pumped to the plant from a well in the valley about 4 miles away. Under the Arizona law, a working-shift is 8 hr. Wages were $6 per day for foremen and mill-men, $4 per day for blacksmiths and engineers, $3.50 per day for miners, and $3 per day for shovelers and trammers. The ore consisted of quartz, in which, above the 250-ft. level, the iron-minerale were largely oxidized and some free gold was visible; below that level few traces of oxidation occurred, and pyrite constituted the principal mineralizer in the quartz, together with occasional pockets of galena and a few eccentric specks of covellite. The 20-stamp mill was equipped with plates for amalgamation, and three Standard tables for concentration. The tails from the tables mere elevated by a centrifugal pump to a launder, by which they were conveyed to a 60-ton cyanide-mill for further treatment. The cyanide-mill was erected at so great a distance from the stamp-mill that a separate crew of workers and a separate power-plant were necessary. No arrangement had been made for the treatment of the concen-

Jan 1, 1907

By John Chipman, Theodore B. Winkler

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By Theodore B. Winkler, John Chipman

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By R. H. Cox, A. S. Allen, James Paone

The southwestern Illinois communities of Belleville and Maryville lie within the greater metropolitan area surrounding St. Louis. Missouri. They also lie within that part of the Illinois coal basin where the Number 6 coalbed has been mined for more than a century. About half the coal was left as pillars to support the ground surface. Years later, however, damaging movements are affecting buildings, streets, and public utilities in some areas. They are generally believed to be related to abandoned mine workings. The threat of continued or increasing incidence of damage raises the need to explore other subsidence-control measures for protecting affected areas with high population density. Because of experience gained in a subsidence-control program of backfilling abandoned coal mines in the Applachian region and in Rock Springs, Wyoming, the Bureau of Mines was called upon to investigate the subsidence occurrences at Belleville and Maryville, and recommend protective measures. Funds ware appropriated for the Bureau to initiate subsidence-control projects at two residential sites in Belleville and one in Maryville. Subsurface investigation of the sites by diamond core drilling revealed two conditions that differ from those encountered at most sites of previous subsidence-control projects. The mine workings were found to be dry and the mine floor consisted of soft underclay which characteristically loses strength with increase of moisture. It had been anticipated that water would have percolated into the mine workings at one .or more of the sites through cracks resulting from subsidence. Under such conditions Bureau engineers believed that injection of mine waste by the pumped; slurry technique3 would provide support and stabilize any movements initiated by the softening of the clay. With discovery that the underclay deposits at the three sites have apparently not been exposed to water since the mines were operating, hydraulic backfilling of any type was considered inadvisable on the basis of present knowledge. To avoid introducing water, a portable pneumatic system is being devised for injecting minus 0.01 27 m (1/2 in.) mine waste into the mine workings. Machines for pneumatic backfilling have been used in Europe not only for subsidence protection but also for strata control, for reducing spontaneous combustion and methane accumulation, and as a means of waste disposal. The Bureau experimented with a pneumatic machine in the Northern anthracite field of Pennsylvania in the 1950's. Previously pneumatic machines have been installed in active mine workings discharging from horizontal pipelines which conveyed air- borne material into rooms to be filled. In the present adaptation to abandoned mines, the machine and air compressor will be operating at the surface, to impel material vertically down injection boreholes with sufficient air pressure to disperse fill material laterally in mine workings at the base of injection holes. Large diameter access and ventilation boreholes will be provided at one site for entry into mine workings to observe backfilling progress. The Belleville and Maryville projects are part of the Mined Land Demonstration Program of the Bureau of Mines. The Illinois State Geological Survey and Department of Mines and Minerals are furnishing technical support.

Jan 1, 1979

By R. H. Card

THE geophysicist is interested greatly in the resistivities of different formations or parts of the earth's crust; sometimes he is interested in a single figure in the nature of an average, or what may be called the effec-tive resistivity, of all the formations or parts of the crust at a given location to a certain depth. Conversely, the engineer whose work is concerned with the coordination of power and communication lines in such a manner as to avoid electrical interference between these two types of facilities is concerned very much with this effective resistivity; to a lesser extent he is interested in the resistivities of individual forma-tions. In connection with his work the coordination engineer often estimates the effective resistivity; of the earth from measurements of the mutual impedances of lines; in other instances he derives front measure-ments of a different type the resistivities of different layers of the crust and synthesizes these to obtain an estimate of the effective resistivity. In connection with problems concerning the coordination of power and telephone lines, measurements from which earth resistivities can be estimated have been made at many points in the United States by the American Telephone and Telegraph Co. and its associated companies, in cooperation with various power companies and with railroad companies having electrified sections of line. Other such measurements have been made by the Joint Subcommittee on Development and Research of the Edison Electric Institute and the Bell Telephone System. A study has been made of the correlation of these data with the ages and types of materials of the strata of the earth's crust at each of the test locations. The purpose of this study has been primarily to provide information to assist in predicting the order of magnitude of effective resistivities to be used in the preliminary consideration of problems con-cerned with the coordination of power and communication lines. To make the results of such a study, most useful, it is essential that the geo-logical data to be secured when such a prediction is wanted be readily obtainable. Data on the ages of strata and the types of materials com-posing geological structures can usually be obtained, therefore particu-

Jan 1, 1937