Search Documents

By T. J. Woods

This paper deals with the origin, definition and prevention of scabs on semifinished rolled-steel product. Mold coatings, which are considered essential in scab prevention, were found to be effective only in relation to the ingot surface of semikilled and killed steels and not necessary for the rolled product. That is to say, the scabs on ingots caused by having been cast in uncoated molds are eliminated in the soaking and rolling operations, therefore are not present on the rolled product. This fact, which is contrary to the average opinion, was established after extensive and thorough experiments had proved the ordinary conception of the origin of scabs to be incorrect. This subject may be of little or no concern to steel plants producing small ingots for the manufacture of small billets and bars, except as it may be of interest in showing why their surface troubles with scabs do not exist on the product of heats with normal pouring practice. But to the producer of large ingots to be rolled into slabs for large plates used in shipbuilding, it is a very important subject. Definition of a Scab The generally accepted opinion is that the individual scabs present on rolled products (as shown by Fig. I) are considered to have been individual splashes on the ingot surface. This opinion was found to be incorrect. Experiments showed that there were no individual scabs on the product that had appeared as individuals on the ingot surface. The single scabs seen are either pieces of a shell that is present near the bottom of all top-cast ingots, or a veneer that may be present on any part of an ingot improperly poured, as when the stream strikes the mold wall. This definition is based on a detailed study of scabs and their characteristics in which the following have been found true: Location.—On the product of heats poured without trouble, scabs, if present, are always on the product that corresponds to the bottom end of the ingot, and usually occur in clusters. This is true whether molds are coated or not. Shape.—There is no regularity as to shape, size or thickness. It is sometimes possible to separate a few pieces and place them together, like pieces of a jigsaw puzzle, indicating that at one time they had been united as one piece. If individual splashes were the origin of scabs, the foregoing would not be true. Instead, the splashes, which occur throughout the pouring of the ingots, would be present uniformly over the entire product and there would be considerable similarity in the shape and thickness of the scabs. Experimental Work Our experimental work was conducted on 200-ton heats of semikilled plate steel tapped into an oval ladle 15 ft. high. All ingots were top-cast direct into 24 by 54 by 82-in. molds, straight-sided, set on flat stools. Two separate studies were made about one year apart, each study extending

Jan 1, 1943

By Paul A. Beck, M. N. Parthasarathi

By determining the (220) pole figure for OFHC copper rolled to 96 pct R. .A., the occurrence of four texture components of the type (135) [211] was confirmed. It was found that the total volume fraction of material close to the four symmetrical orientations of this type is larger than the volume fraction of the other components put together. THE rolling texture of copper was described by early investigators1'" as a mixture of components of the (110)[l12] and (112) [11l] types. Other studies, still using the qualitative photographic method of texture determination arrived, instead, at orientations of the type (135) [533] or (135) [211] for copper3'4 and at the closely related "Z-texture" for a fee nickel-iron alloy.5 The prevalence of this type of orientation, near (123) [412], in the rolling texture of aluminum and of copper was later confirmed by means of quantitative diffractometer methods.' However, in a recent paper7 Jones and Fell stated that the (110) [112] and (112) [111] double texture was in better agreement with the measurements of Young's modulus for cold-rolled copper.' These authors also expressed their belief that the "roll texture" can be determined by means of two photographic quasi-fiber texture patterns taken with sheet specimens rotated around the rolling direction and the transverse direction, respectively. Jones and Fell found7 that the results obtained from such patterns for cold-rolled nickel did not agree with any of the orientations mentioned above, but they suggested that the observed diffraction spots may have been brought about by the overlapping of reflections due to the (110) [112] and (112) [11l] double texture components. Jones and Fell concluded that the (123) 14121 type orientation is inconsistent with their patterns. They also stated, without offering any supporting evidence, that this orientation is inconsistent with the (220) pole figure. "Ideal orientations" are often used for a very rough description of the principal orientations encountered in a texture, It is, however, well to remember the fact that, no matter how "accurate", these ideal orientations are only schematic representatives of a continuous distribution9, which often (as in the case of rolled copper) includes extensive orientation spreads. The attempt by Jones and Fell7 to use elastic modulus data in deciding between various ideal orientations in the rolling texture of copper neglects this fact. The inadequacy of two-dimensional "axis density figures" in describing orientation distributions in sheet textures was previously discussed.9 It was also pointed out9 that there is no reliable evidence to prove that orientation distributions derived by the "quasi-fiber method" from rotated sheet specimens are fully equivalent to the corresponding information obtainable from quantitative pole figures. The view that a sheet texture could be adequately determined by means of two photographic quasi-fiber texture patterns is obviously erroneous9. The question as to the consistency with the (220) pole figure of ideal orientations derived from the (111) and (200) pole figures is, on the other hand, certainly very relevant. Since no quantitative (220) pole figure for cold-rolled copper appears to be available in the literature, the following work was undertaken. EXPERIMENTAL METHOD An extruded rod of OFHC copper, 1 in. in diam, was given alternate rolling (30 to 35 pct R.A.) and

Jan 1, 1962

By Ancel St. John

During a session on coal and coke at the February, 1926, meeting of the American Institute of Mining and Metallurgical Engineers, the writer called attention to the important work on the X-ray analysis of coal1,2 being carried on in England by C. Norman Kemp and his associates. This aroused so much interest that a paper on the subject was requested for the October meeting. It has seemed advisable to make this paper a preliminary survey of the present status in the application of X-ray methods to coal problems and to follow it from time to time with further articles as the art develops. A survey of this sort naturally divides itself into two parts, radio-scopic analysis of the distribution of constituents through the body of the coal, and diffraction analysis of the state of association of the elementary components. In this article the subject matter concerning radioscopic analysis has been drawn almost entirely from the writings of Kemp and his associates and the illustrations have been sptcially furnished by him. It is a pleasure to record here a great indebtedness for this courtesy and cooperation. The subject matter and illustrations concerning diffraction analysis are taken from the author's unpublished researches. Nature and Properties of X-rays Before proceeding it is well to recall the nature and some of the properties of X-rays, as well as our present conception of atomic structure According to the accepted theory atoms are composed of electrically-charged particles. A positively-charged center, called the nucleus,

Jan 1, 1927

By E. M. Wise

IN a previous communications the improvement in strength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are pre-sented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for deter-mining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a, novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum.

Jan 1, 1933

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

By Ernest Gayford

This is a nontechnical paper on flotation, subdivided under three general headings: (I) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? Definition T. A. Rickard defines flotation' as "the act or state of floating," from the French flottaison, water-line and flotter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer,2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small particles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the films of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart3 defines flotation as follows: Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928

By R. E. Ogilvie, J. I. Goldstein, R. E. Hanneman

The interdiffusion coefficients for the Fe-Ni system were determined as a function of composition in both the a and y phases at 1 atm pressure. The inter diffusion coefficients were also determined in the y phase at 40 kbar pressure. The concentration gradients were measured with an electron probe, and the diffusion coefficients were calculated by the Matano analysis. At 1 atm, Ey increases with nickel content up to 65 at. pct Ni. The relationship of Dy with temperature and nickel concentration, up to 50 at. pct Ni, is given by the equation DY-l atm = exp(.0519 CN~ +1.15) MANY of the transformations that occur in the solid state are diffusion-controlled, especially those involving precipitate growth in most metallurgical systems. Multicomponent diffusion is usually expressed in terms of a chemical or an inter diffusion The activation energy Q at 1 atm decreases from pure iron to 60 to 70 at. pct Ni and decreases from pztre nickel to 60 to 70 at. pct Ni. The Kirkendall marker movement indicates that DFe is greater than DNi zcp to about 60 at. pct Ni. Above 60 at. pct Ni, however, DNi becomes peater than DFe The inter diffusion coefficients were also compared with those calculated from self-diffusion data. A comparison between calculated and measured coefficients shows only rough agreement. The effect of 40 kbar pressure is to decrease DyPl atm by an order of magnitude. The activation volumes for high-pressure diffusion are in favorable agreement with theoretical models developed for self-diffusion. coefficient which determines the rate at which material is transferred from the matrix phase to the precipitate and hence determines the growth rate of the precipitate. Since the numerical values of the diffusion coefficients differ widely as a function of the metallic system, temperature, and pressure, the diffusion coefficients must be determined for each particular environmental condition. Of long-standing interest is the growth of the classic Widmanstatten pattern in metallic (Fe-Ni) meteorites. The growth rate of the pattern is controlled by the diffusion coefficients in the Fe-Ni system. Since these coefficients are essential to calculating the growth rate of the pattern, we found it necessary to determine the diffusion coefficients

Jan 1, 1965

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal The effect is known as "caring" and the protuberances are called "ears" Other terms frequently heard are "tips," "scallops," and "corners " It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip Numerous papers dealing with various aspects of the caring effect have appeared in the literature, those listed in the references' being especially interesting and valuable An investigation of the factors influencing caring of brass cups has been in progress in the laboratories of the American Brass Co for several years, and it was thought desirable to make some of the results generally available in summarized form The present paper discusses many factors that do and do not contribute to ear formation In addition, a section is devoted to methods of minimizing the caring tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced In the space available, it is impossible to quote detailed experimental procedures and numerical results However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip The two-ear form that sometimes appears is also traceable to gauge variations However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself

Jan 1, 1942

By Carl G. Hogberg

During recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. Principles 01 Iron Desulphurization in Furnace Although investigations of the blastfurnace process have not clearly revealed the detailed mechanism of iron desulphuri-zation within the furnace, they have been sufficiently extensive to permit a postula tion of the following general principles: 1. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurizatioil is relatively narrow, being confined to a vertical distance extending zapproximately from tuyere level to the iron-slag interface in the hearth.' 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.= Coke ash is released as the coke bums in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By Carl G. Hogberg

During recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. Principles 01 Iron Desulphurization in Furnace Although investigations of the blastfurnace process have not clearly revealed the detailed mechanism of iron desulphuri-zation within the furnace, they have been sufficiently extensive to permit a postula tion of the following general principles: 1. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurizatioil is relatively narrow, being confined to a vertical distance extending zapproximately from tuyere level to the iron-slag interface in the hearth.' 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.= Coke ash is released as the coke bums in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By G. L. Oldright, F. W. Schroeder

Very great changes were made in the dimensions of the smelting hearths of the furnaces in the period from about 1800 to 1906, the length increasing from about 11 to 116 ft., and the width from 8 to 19 ft. During this time the tonnage smelted increased from about 9 to 250 tons per 24 hr., and the tons of charge smelted per ton of coal increased from 0.77 to 4.3. Dr. Mathewson3 noted no great difference in the "fuel ratio" (i. e., the amount of charge smelted per ton of coal) as the furnace at Anaconda was increased in length by stages from 85 to 116 ft. (The percentage of copper in the slag, however, was lowered from 0.42 to 0.36 per cent. The other components of the slag were not given.) Lump coal fired on grates was the fuel used during this period. The practice in operating the furnaces over such a length of time naturally varied considerably, and there were differences in composition and nature of the charge, yet it may he considered that the improvements made were due largely to increases in the size of the furnace used. Doubtless some credit should be given to improvements in operating technique, like changes in the methods of firing the lump coal. However, the greater part of the advance was probably due to factors influencing the

Jan 1, 1928

By R. E. HORE, J. B. Tyrrell

IN the vicinity of Kirkland Lake, northern Ontario, several gold mines are producing, and three are at present being operated very profitably. At these three mines and on the adjoining properties east and west of them there have been important developments during the past year, and additional equipment has been installed to permit a large increase in output. At the end of 1924 the total production amounted to $13,688,600. For the year 1926 the production is estimated at about $19,000,000, and during 1926 the output should be much greater than that of 1925. The mines which are being operated most profitably and are producing a large part of the ore now being milled are the Wright-Hargreaves, Lake Shore and Teck-Hughes. Others which have contributed smaller amounts are the Tough-Oakes-Burnside and the Kirk- land Lake Gold mines.

Jan 1, 1926

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By H. S. Kalish, F. J. Dunkerley

INTRODUCTION AND PREVIOUS WORK THE determination of the low temperature tensile properties of tin and tin-lead alloys was initiated as part of an extensive research program on the phasial equilibria of tin binary systems below 13.2°C and the property changes associated therewith. A survey of the literature revealed that, although some room temperature tensile data were available for tin and a few tin-lead alloys, there existed no survey report of the low temperature tensile properties of these alloys. Accordingly, the tensile data for tin and a series of pure tin alloys containing from 0.01 to 50 pct lead were measured at eleven temperatures from -196 to +20°C and are presented here in survey form. In addition to the importance of these tensile data as a preliminary to certain fundamental research, this information promises also to be of commercial importance because of the 'extensive use now being made of tin-lead solders in refrigeration and gas liquefaction equipment. Occasional failures of the solders in low temperature service have been attributed by some metallurgists to low temperature mbrittlement, while others hold that failure results from the transformation of the tin-rich phase of the solder from the solid white (beta) to the powdered gray (alpha) form. From the data previously available in the literature, neither of these explanations can be completely corroborated. Cohen and van Lieshout1 have established the beta to alpha tin transformation at 13.2°C and have shown that strain accelerates the transformation. Further, they showed that although I pct lead retarded the transformation, it was not eliminated. It will be pertinent, then, to note whether the beta to alpha transformation of the tin-rich phase will occur in a short-time tensile test. Polanyi and Schmid2 studied the tensile . properties of tin single crystals at -185°C and report that tin is brittle at-this temperature. In 1946, Kostenets3 reported that pure tin was brittle at -196 and -253°C, while lead remained ductile at both these temperatures. He also studied the tensile properties of tin-lead alloys containing from 10 to 75 pct lead at -253, -196 and +17°C. The ultimate tensile strength increased more than two times in going from room temperature to -196°C and about three times that value on further cooling to -253°C. All the alloys were brittle at -6°C except those containing more than 75 pct lead. Even at -253°C, the 75 pct lead alloy retained 36 pct elonga¬tion in a 30 mm-ga. length. Creep is also an important phenomenon

Jan 1, 1948

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By Theodore W. Robinson

WHEREVER the amount of work renders it practicable the plan of using permanent standard solutions, in connection with the colorimetric carbon test, affords such manifold advantages that it is to be strongly recommended. That it has not attained a wider and more general application, is mainly due to the fact that, as the method is generally employed, the difficulty attending the production of the colors, and their doubtful stability when produced, have been only too evident to those who have undertaken their composition. The old method of using standard solutions made from sugar, coffee, etc., has always been hampered by the tendency of the colors to change upon exposure to the light, and the consequent liability to serious error, unless they are closely watched. Appreciating these difficulties, while recognizing the desirability of permanent colors, Mr. Magnus Troilius, at the suggestion of Prof. F. L. Erkmann, investigated the properties of cobalt, copper and ferric chlorides, with the view of determining their efficacy in the production of standard solutions. His results, as obtained, seem to have been satisfactory, but his treatment failed to eliminate many of the objections that have rendered the use of organic colors undesirable. The

Jan 1, 1888

By B. Chalmers, L. Bäckerud

The growth temperature of dendrite tips has been measured in a binary alloy system, Al-Cu, as a function of rate of formation of solid phase. Metallographic examination has rerealed the dendritic structure dereloped during different stages of the freezing process and factors influencing the undercooling, such as solute buildup, surface tension, and kinetic effects, have been estimated. Practical implications of the results are discussed. THE development of a dendritic growth pattern during the solidification of metals and alloys has an influence at least equal to that of grain size on the properties of the casting or ingot being produced. and consequently much interest has been devoted to the study of this phenomenon. A review of the knowledge gathered up to 1964 has been given by Chalmers.' Among recent publications in the area the works of Jackson et al 2 and Flemings and his coworkers3,4 are of special interest. This work is an experimental study of the factors which influence the development of a dendritic pattern during the solidification of a typical binary alloy system, A1-Cu, when there is no heat source in the liquid. This means that the temperature and the temperature gradient are controlled by the heat extraction from and latent heat evolved by the growing crystals. EXPERIMENTAL PROCEDURE Samples were prepared from a master alloy made up of aluminum, 99.995 pct, and copper. 99.99 pct, of the concentrations given below and of sufficient size to fill cylindrical graphite molds of 35 mm ID and 35 mm height. Bottom. wall. and lid of the graphite molds were all of 6 mm thickness, Fig. 1. Thin ceramic thermocouple shields could be introduced at different positions in the sample through holes in the lid. The assembly was heated in a small vertical resistance furnace to a suitable temperature. 700° to 720°C. which is well above the melting point of the sample. It was thereafter taken out of the furnace and chilled at selected rates, and the temperature changes in the sample were recorded. For high sensitivity in the temperature recordings, a reference thermocouple was held in a solidifying pure aluminum melt. which was very well insulated and therefore was at a constant temperature. 660°C, for nearly half an hour. The thermocouples were connected so that the difference voltage was fed into the recorder of which the most sensitive range was 1 mV. Temperature variations could be read to within 0.l°C. The thermocouples used were of the Chromel-Alumel type (28- or 38-gage wires) and the recorder a two-pen Moseley strip chart recorder. The different rates of chilling were obtained in the following way. a) The graphite crucible was wrapped in one or two layers of an insulating. feltlike material (Fiberfrax paper from the Carborundum Co.). The drop in temperature per unit time after complete solidification could thereby be varied from 8" to 18°C per min. This corresponds to a rate of heat extraction in the given samples from 0.08 to 0.17 cal cm-' sec-I. 6) The bare graphite mold was placed free on a piece of firebrick. The measured temperature drop was around 50°C per min (-0.5 cal cm-" ' sec- I). c) By blowing compressed air through a tube with many holes surrounding the mold in a ring shape. the rate of heat transfer could be raised to 150' to 200°C per min (-1.7 cal cm-3 sec- I). d) Cooling rates around 1000 C per mill (-9.4 cal cm-3 sec-l) were obtained by substituting the air in the device used in c by water. The range of cooling rates used in these experiments correspond to technical casting processes from slow solidification as obtained in sand molds to very rapid freezing which occurs in some continuous casting and welding processes. EXPERIMENTAL RESULTS The A1-Cu system was chosen for the experiments: the relevant part of the phase diagram is reproduced in Fig. 2. Observation of the Center Temperature. When a thermocouple is inserted in the center of the melt. the type of cooling curves obtained at slow solidification rates differs little from numerous published curves from similar systems. and the solidification pattern

Jan 1, 1970

The key-note of good writing, as of good manners, is B natural. Sincerity is the first requisite for effective writing. When a man says what he knows or believes, he is likely to be interesting, because each human being possesses an individuality, a point of view, or a range of sympathy that makes him different from his fellows. To say or to write what you do not think, for the mere sake of talking or writing, is a verbal exercise that must be performed with extraordinary skill if it is to be attractive. Affectations are rarely attractive, rarely effective. To be natural is to be yourself, not a poseur; to give the reader the best of yourself, instead of re-warming the baked meats of yesterday. Quotations-which are second-hand thoughts-will serve occasionally when the thing you want to say has been said so well by another that it would be waste of energy to try to say it better; gut, as a rule, the utterance of the writer himself is more interesting than the quotation, because the writer brings something of himself to bear on the subject, and for the moment is more in touch with the reader than any dear departed author. Therefore, say things as best you can in your own way, neither in borrowed words nor in the phraseology that mimics another. Write as if you were speaking to a person whom you desire to persuade or convince. You will then write better than you speak, because, in the first place, you can be more deliberate, and, secondly, you can revise what you have written. Speaking and writing are similar mental acts, with a difference: the difference between eating food raw and eating it cooked. Some kinds of food gain nothing by being cooked; likewise some kinds of utterance are not bettered by being written down first; but most expressions of thought, especially

Jan 1, 1931