Search Documents

By J. E. Johnson

Discussion of the paper of Prof. Henry M. Howe, presented in abstract by Bradley Stoughton at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1181 to 1227. J. E. JOHNSON, JR., Ashland, Wis. :-This material is largely beyond the understanding of most of us practical men, but there are certain portions of that diagram that are of enormous importance. We have been conducting a, very extensive investigation of the quality of charcoal-iron and of all iron, and we have found that this eutectic point here (indicating on chart) is a sort of balance point between the good irons and the bad ones, and I have some slides to show what practical results we have found depending on this point here on the d diagram; and it would be a mistake for men who were -concerned with operation and were getting practical results, to think that these things are of no importance. They are exceedingly hard to understand, and I confess that a great deal of them is beyond me, but there is no doubt that the quality of iron depends to an enormous extent on the location of the carbon content of the iron to the right and left of this point, and the position of that point is dependent upon the silicon, and I wish to make a plea to the practical and operating members of the Institute not to disregard this material on account of its being highly scientific, because I hope to show later that there are matters of the highest practical importance that depend directly upon certain portions of this diagram. HENRY D. HIBBARD, Plainfield, N. J. :-T understand that washed metal, which, is practically pure iron and carbon, does not solidify at one instant, is cast-iron does, but passes through a mushy stage. That has been an enigma as to how and why it did so, and possibly some light might be thrown on it in this connection. BRADLEY STOUGHTON, New York, N. Y.:-If Wittorff's propositions are accepted, washed metal containing more than 4.1 per cent. of carbon would begin to solidify as liquid plus Fe4C

Dec 1, 1912

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By Ernest F. Burchard

A Reconnaissance of the manganese- and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines, under instructions of the Secretary of the Interior, in the spring of 1918. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the island. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, quantity, and availability of the manganese- and chrome-ore deposits in Cuba. Accordingly, the work comprised examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to a determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. Wile it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Moreover, the necessity for paying particular attention to the ore deposits and the mines precluded the possibility of making more general studies of the geology of the region, and of making satisfactory collections of country rock and of fossils, and so for other details as to the geography and geology of Cuba the reader is referred to the report by Hayes, Vaughan, and Spencer.l Mr. Burch returned to the United States about 10 days in advance of the writer, who continued, in company with Sr. Montoulieu, investigations of reported deposits in Pinar del Rio, Matanzas, and Santa Clara Provinces. On his arrival in Washington, Mr. Burch submitted to the Director of the Bureau of Mines a summary of the results of the work to date. Later the writer published, as Press Bulietin 190. 380 of the U. S. Geological Survey, a statement concerning the chrome and man-

Jan 1, 1920

By AIME AIME

GENERAL COMMITTEES. SAN FRANCISCO:-ExECUTIVE, Hon. William C. Ralston, Chairman; RECEPTION, Prow. Samuel B. Christy, Chairman; SESSIONS, Frederic W. Bradley, Chairman; PRESS, H. Foster Bain, Chairman; FINANCE, Mark L. Requa, Chairman; EXCURSIONS AND ENTERTAINMENTS, Edward H. Benjamin, Chairman. Assisted by Harry P. Stow, C. W.Merrill, F. W. Griffin, Gelasio Caetani, Albert Burch, Newton Cleaveland, Corey C. Brayton and R. E. Cranston. Los ANGELES :-EXECUTIVE, Theo. B. Comstock, Chairman; R. W. Hadden, Secretary; H. R. Simpson, Treasurer. Institute Headquarters at Hotel St. Francis. The first and opening session, held Tuesday afternoon, Oct. 10,. in the Reception-Hall of the St. Francis, was called to order by State Senator William C. Ralston, Chairman of the Executive Committee, who in a few well-chosen words welcomed the visiting members and guests of the Institute to San Francisco. He said it was twelve years since the last meeting on the Pacific Coast and that it was here that the greatest feats. of mining had been accomplished in the history of the country. He told of the work that had been done on the continent and of the new methods introduced by the mining engineers for the betterment of the nation. He then introduced Capt. Robert W. Hunt, twice past President of the Institute, and present Acting President for the San Francisco meeting and the subsequent visit to Japan, who responded cordially to Mr. Ralston's welcoming address. By unanimous vote, the Secretary was instructed to send a telegram to President Charles Kirchhoff expressing regret for his absence, and hoping for a rapid improvement in the health of his mother. The following papers were presented in brief oral abstract by the authors: . * Electrolytic Refining at the U. S. Mint, San Francisco, Cal., by Edward B. Durham, San Francisco, Cal. The Parral Tank System of Agitating Slime-Pulp, by Bernard MacDonald, Guanajuato, Mexico. * The Newport Iron-Mine, Ironwood, Mich., by B. W. Vallat, Ironwood, Mich. (illustrated by lantern-slides). * Distributed in pamphlet worm.

Nov 1, 1911

By Prince Lazarovich, Hrebelianovich

I WAS asked by the chairman of one of the Sessions on Employment Problems to talk about the viewpoint of the foreign workingman. I am not a workingman. I have never done what a work-hand might call an honest day's labor; that is, I have never been in a factory or manufacturing plant or in a mine, though in truth, hard work and I are well acquainted. I was a soldier, am an engineer, have long been actively interested in the most important waterway construction in the near East, have served politics and diplomacy, written books and lectured at universities. My knowledge of the foreign workingman in this country comes from the fact that my own compatriots here at various times came to me and appealed for advice and help, and last year I was asked by the employment manager of a corporation to undertake a welfare job at one of their plants. I went out, saw the plant, talked with the superintendent and outlined certain of my ideas which he personally heartily approved, but which did not find favor with those higher up. I approach the subject of the foreign workman's point of view with the understanding that the industrial employer's effort is for the maximum of efficiency. I am conversant with labor conditions abroad both in industry and agriculture. What I have learned of industrial conditions in America as they affect the foreign immigrant has been chiefly gathered from the cases referred to of foreign workmen who from time to time have come to me with their troubles. In the course of those investigations, in order to give whatever help or advice was possible, I have been impressed with the fact that the great United States industries evidently had- pot yet sufficiently recognized the value of studying the conditions of the workingman in the lands of his origin across the seas. A careful study of that which could be called the moral element in connection with its foreign labor would give industry a knowledge of the man's reason for coming, what' grievances he brings with him, his hopes for a future, and the peculiar character of his capacities. The employer would thereby be enabled to meet the man, to be helpful to him, to aid him and at the same time promote industrial efficiency, inasmuch as a workman who believes that he is being dealt with humanly and squarely is contented and satisfied and will give willingly, and even with pride, the best that is in him; justice and a fair deal is all the man wants.

Jan 4, 1918

By A. T. Yu

On March 18, 1964, the 52,000 dwt ore carrier M/S Houn Maru called at the port of Coquimbo, Chile, on its maiden voyage to take iron ore to Japan. This marked the first time a vessel of this size ever arrived at Coquimbo, and the event promises to drastically accelerate henceforth iron ore exports from Coquimbo province. This was made possible by the use of a versatile shiploading system recently installed by Cia. Minera Santa Fe. Coquimbo has no mechanized loading facilities other than six conventional 5-ton cargo cranes. Limited space on shore further complicates the stocking problems. To make the best of what is available, a meticulously organized semi-hand-loading system has been developed through the years.

Jan 5, 1964

By G. Gabra

The kinetics of acidified thiourea leaching of pyrite concentrate was investigated at temperature ranging form 20 °C to a 60 °C. The effect of various parameters on the dissolution rates are discussed. The gold extraction was found to be zero and first orders with respect to Fe (111) and thiourea concentration, respectively. The order of the reaction with respect to sulfuric acid was found to be zero. The activation energy was determined from the Arrhenius plot as 2,039 kcal mole -1 (for a freshly prepared acidic solution containing Fe (111) as the oxidant and at 800 rpm stirring speed. This relatively low activation energy value suggests that the gold extraction is controlled by a-physical phenomenon. Under optimum conditions, more than 90% of gold has been dissolved in about 30 min. and 95% in 60 min. Attempt to recover gold from thiourea solution using active carbon is also discussed.

Jan 1, 1984

Jan 1, 1970

By W. V. Long, D. H. Reynolds, R. B. Bhappu

Equilibrium distribution coefficients were determined for some monovalent and polyvalent ions for several absorbing and exchanging media as functions of pH and initial ion concentration. Among ions studied were NH4 (I), K(I), Ni(II), Ce(III), Th(IV), and Mo(VI). Absorbents used were: ion exchange resins; a tertiary, and a quaternary amine in an inert solvent; and some activated carbons. The ions studied were in aqueous HCI, HNO3, H2SO4, or HC104 solutions. The classical mass action expression proved of little value in describing the variations observed. The data indicate that the determining factors in absorption and ion exchange may be the ionic species in the aqueous solution, which in turn depend upon pH, dilution, and perhaps other conditions. Three sorption processes have become prominent in recovering values from leach solutions. These are: 1) ion exchange, 2) solvent extraction (liquid ion exchange), and 3) physical adsorption by materials of high specific surface. In the first two of these processes the exchange reaction is considered chemical in nature, and is discussed in terms of the mass action principle. The third is considered a surface phenomenon and is discussed in terms of surface areas and various forms (Gouy, Stern, Grahame, etc.) of the Helmholtz double-layer theory. Generally speaking, we have found in chemical analysis and hydrometallurgical studies that there are close similarities between the three sorption processes, and also differences which are difficult to reconcile with any of the usual theoretical treatments. That others have experienced the same troubles is shown by the fact that usable processes, in chemical analysis as well as in hydrometallurgy, generally are discovered by empirical procedures. EXPERIMENTAL CONSlDERATlONS The gaps between theory and practice have allowed many conflicting statements to appear in the litera- ture. To learn, in particular, the behavior of some metallic ions on a cation exchange resin at a constant pH, equilibration studies were made over a wide range of concentrations.' Results are shown in Fig. 1 for four metals in hydrochloric acid solution on a strongly acidic cation exchange resin, AG 50W-X8 (Bio-Rad). The distribution coefficient, defined as D = amount of metal extracted per g of resin/amount of metal unextracted per ml of solution is seen to vary in a way to support all manner of reports about its behavior with changes in solution concentration. The metals used were chosen from those least likely to form stable chloro-complexes. The changes of slope in the various isotherms may reflect formation of unsuspected chloro-complexes of low stability (ion-pairing for example) whose concen-

Jan 1, 1967

By George I. Adams

PHYSICAL AND CLIMATIC DIVISIONS. PERU is divided into three regions-the coast, the sierra, or high mountainous region, and the a montana," or forest region of the Amazon basin. The Coast.-The coast is an arid region. No rain falls excepting in the extreme northern part, which borders the Gulf of Guayaquil. There is, however, a slight precipitation in the form of mist (garua), which occurs on the coast hills during the so-called winter months. The aridity of the coast is due principally to the antarctic or Humboldt ocean-current, which, being cold and having a temperature lower than that of the land, absorbs rather than produces vapors. The coast mists occur during the season when the land is relatively cold. Near the Gulf of Guayaquil the antarctic current diverges from the coast, so that in the Tumbes valley and adjacent country the conditions in the summer months are such as produce rains. In the remaining valleys of the coast, agriculture is made possible only by means of irrigation, and is accordingly very limited in extent, although rich and varied. In the northern and south-central portions of the coast, plains extend inland from the sea, while in the southern part there is a coastal plain separated from the Pacific by a range of coast hills. Between the northern and south-central plains, as well as between the south-central and southern, the foothills of the sierra descend to the seacoast. The Sierra.-The sierra embraces the high land dominated by the lofty cordilleras of the Andes. In the southern part of Peru there are two cordilleras, the western and the eastern, which enter from Chile and Bolivia respectively, and inclose between them the Titicaca Lake basin. To the north of Lake Titicaca these cordilleras unite in the knot of Vilcanota, south of Cuzco. From this knot three cordilleras, known as the western, the central, and the eastern, extend to the northward, reuniting in the

Jan 7, 1908

By M. R. J. Wyllie, Michael A. Torcaso

With the continued deep drilling of today, increasing numbers of high pressure and high temperature gas-condensate reservoirs are being discovered. Correspondingly, the ranges of properties of gas-condensate reservoir fluids are also being increased. The literature1*'." contains several excellent reviews of the property ranges in presently known condensate reservoirs. When one examines these property ranges, it becomes apparent that the need for reliable data is great if the engineer is to evaluate properly or appraise a gas-condensate reservoir. It is the purpose of this paper to present phase-behavior data that will point out some of the important variables that influence recovery from gas-condensate reservoirs produced by pressure depletion. All these variables may be resolved into two major categories: the hydroc:arbon composition of the reservoir fluid and the physical properties of the reservoir. But the variables which we will consider are those which are usually determined from well tests shortly after discovery and are, consequently, readily available to the engineer. They are as follows: (1) the producing separator gas-stock-tank liquid ratio, (2) stock-tank liquid gravity, and (3) reservoir temperature. Laboratory depletion studies have been performed on several reservoir fluids to illustrate the effect of changes in the cronsidered variables upon ultimate recoveries. The deviation factors, Z, of a series of reservoir fluids were determined experimentally to illustrate their order of magnitude and their effect upon the calculation of in-place reserves existing at high pressurcs and temperatures. The procedures followed in conjunction with the performance of these studies and their associated calculations are illustrated in Fig. 1. For the purpose of this paper, the depletion recoveries are expressed only in terms of pcr cent of initial stock-tank liquid, with the abandonment pressure assumed to be 500 psig. VARIATION OF RECOVERY WITH INITIAL PRODUCING SEPARATOR GAS-STOCK-TANK LIQUID RATIO The producing separator gas-stock-tank liquid ratio has long been one of the principal criteria in assumptions and generalized correlations' used for the estimation of ultimate recovery from gas-condensate reservoirs. Fig. 2 presents a plot of the cumulative recovery of stock-tank liquid at abandonment as a function of the initial producing separator gas-stock-tank liquid ratio. The graphical illustration represents the results of 44 laboratory depletion studies performed on actual gas-condensate fluids. These data are presented not only to illustrate the general trend of ultimate recovery increase with initial producing ratio increase but to emphasize the considerable variation in possible recovery at any given producing ratio. Table 1 presents the properties of two actual reservoir fluids chosen to illustrate the approximate extremities of producing ratios for gas-condensate systems. The fluids designated as A and B exhibited initial producing ratios of 3,400 and 114,000 scf/bbl, respectively. Fig. 3 presents a graphical comparison of the cumulative stock-tank liquid recoveries, calculated from the well-stream compositions and produced volumes for each fluid during depletion. It is to be noted that Fluid A exhibited a recovery of only 16.5 per cent when produced to an assumed abandonment pressure of 500 psig while the corresponding recovery for Fluid B was calculated to be 62.2 per cent. This difference in recovery, which exemplifies the general trend of recovery increase with initial producing ratio increase, is readily explained by consid-

By W. J. Verner, J. R. Lucas

Billions of tons of bulk solid materials are processed through our industrial plants each year, and the tonnage is steadily rising. It has been estimated that for every dollar spent in industry as a whole, approxinlately 30 cents is consumed in the handling of bulk solid materials. It is in this category that tremendous savings are possible through the use of improved techniques. Since World War 11, the mining, steel, chemical, and grain industries, among others have made use of increased materials-handling automation in order to gain some of these savings. However, in a chain of automatic operations, every link must be completely reliable, for if there is a single failure, the whole system immediately becomes ineffective. Only too often the weak link in the chain proves to be the flow of bulk solids from bins. To contribute to the fundamental knowledge in this area, a research study has been continuing at The Ohio State University. The principal objective of the investigation has been to study the internal stresses existing in confined bulk solids. LITERATURE SURVEY Literature studies have revealed that many outstanding people have made contributions to the field of bulk solids. For instance, C. F. Jenkin,1 suggested: a. The pressure on a bin wall is not directly proportional to the depth beneath the surface of material in the bin. b. The vertical pressure distribution on the base of a bin is not actually uniform but is a variable. c. Arches form in bins as a result of very small deformations of the material in the bin. This deformation causes a series of gaps to appear, and consequently causes the disappearance of diagonal forces that cannot act across these gaps. The removal of the diagonal forces causes horizontal forces to be introduced which seem to be the chief cause of arching. 11. A. Janssen,4 in 1895 in connection with his experiments on bins, derived a differential equation to describe both the lateral and vertical pressure in bins with vertical sides. This represents a significant contribution to bulk solid theory, and thus its solution is reproduced as follows: L = KV = RW/U' [l-e -U'KY/R] I where L is the lateral pressure of the bulk solid in psf., V is the vertical pressure of the bulk solid in psf., K is the ratio of the lateral pressure to the vertical pressure at any point, R is the hydraulic radius of the bin in feet, W is the density of the bulk solid in lbs. per cubic feet, U' is the coefficient of friction between the stored material and the bin wall, and Y is the head of material above the point in question in feet. In 1903, Jamieson,6 in an elaborate series of experiments on full sized bins measured vertical and lateral pressures by hydraulic diaphragms. He determined many values for mediums of corn, wheat, peas, and flaxseed. In 1951, Caughey, Tooles, and scheer3 measured both lateral and vertical pressure in deep bins by using strain guages on steel bands. Values were calculated for cement, gravel, sand, soy beans, shelled corn

Jan 1, 1961

By M. V. Mielke, R. E. Hagen, R. L. Bennett

FINE IRON ORES, and concentrates such as those produced from taconite, must be converted to lump form by some process of agglomeration before they can be used effectively in the blast furnace or open hearth. At the present time, four major processes for agglomerating these materials are being used on a commercial scale: sintering, nodulizing, pelletizing and briquetting. IN 1945 U. S. Steel Corp. through its subsidiary the Oliver Iron Mining Div., drew up tentative plans for an agglomerating plant on the Mesabi Range which would include a nodulizing kiln and a sintering machine. The purpose of the plant was two- fold: during its initial operation it would provide data on agglomeration of high grade ore fines, and would help relieve the shortage of ore for open hearth charging. Subsequently, it would be available for agglomerating taconite concentrates. While operating on fines screened from direct ore, it was planned to develop techniques and personnel so that a workable plant would be ready to handle taconite concentrates when the time came.

Jan 1, 1954

By John A. Mathews

RESEARCH in the steel industry, as in other lines of manufacturing, has for its principal purpose the increasing of profits. That is what manufacturing companies are for, and all departments of the organization must be so coordinated as to lead to profitable operation. To divide a payroll into productive and non-productive labor is misleading. Productive labor, in fact, is necessary labor, and non- productive labor is the labor we can get along without. One might as well say that the steering wheel is not a part of an automobile as to say that the directing minds of an industry are non-productive. Legitimate manufacturing profits in a steel company or any other company are the reward that the public pays for service rendered or risk taken. The desire for profits is the impelling motive that leads investors .to take risks and build up industries that give employment to others. Every department of a company, be it executive, manufacturing, financial, sales, or research, must contribute to the one end which brings success-profits.

Jan 1, 1921

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By L. L. Seigle

Free energies, heats, and entropies of mixing of solid Fe-Au alloys have been measured by the galvanic cell method between 800° and 900°C. A positive deviation from Raoult's law and a large excess entropy of mixing were observed, both attributable to lattice distortion caused by the disparity in component atom sizes. Since the terminal solid solutortiontions are not regular, thermodynamic properties computed from the location of the mis-cibility gap do not agree well with measured quantities. The electromotive force data suggest some changes in the existing Fe-Au phase diagram. ALTHOUGH a considerable amount of information has been accumulated about the thermodynamic properties of metal solid solutions which exhibit negative deviation from Raoult's law, particularly those in which ordering occurs, relatively few experimental measurements have been made on solutions with positive deviation. This is due to the infrequency of broad homogeneous regions suitable for experimental measurement in solutions of this type, since any marked positive deviations from ideality lead to restricted solubility and the formation of miscibility gaps. Thermodynamic data reported in the literature for such systems have usually been calculated from the location of the miscibility gap boundaries under the assumption that the entropies of mixing are ideal, i.e., the terminal solutions are regular.' One of the few binary systems with both positive deviation and a wide homogeneous range in the solid is the Ni-Au system. A recent investigation of solid Ni-Au alloys' revealed that the entropies of mixing were much larger than ideal and consequently thermal data computed from the phase boundaries assuming regular solutions were seriously in error. Theoretical considerations put forward by Zener indicated that high entropy values should generally be associated with systems possessing a miscibility gap in the solid, when this is due to differences in the size of component atoms. These facts suggest that the regular solution assumption is a poor approximation for many solid solutions with positive deviation and that reliable thermodynamic data generally cannot be obtained by conventional methods from the location of miscibility gap boundaries. The Fe-Au system, Fig. 1, resembles the Ni-Au system in certain respects. The presence of a miscibility gap in the solid indicates a large positive deviation from ideality, but there is nevertheless an extensive single phase region suitable for experimental measurement. The following investigation of solid Fe-Au alloys was carried out in order to obtain additional data on the thermodynamic properties of metal solid solutions with positive deviation from Raoult's law and to further compare thermodynamic data computed from miscibility gap boundaries with those measured experimentally. Experimental Method The thermodynamic properties were derived from measurements of the potential developed between pure solid iron and Fe-Au alloys in a high temperature galvanic cell. The experimental apparatus and technique were the same as those used for the Ni-Au alloys and described in a previous report.' Cell electrodes were 1/16 in. diam rods swaged from chill-cast ingots and annealed for one week at 850°C. The alloys were prepared by melting fine gold granules under argon with pure iron obtained from the National Research Co. The cell electrolyte was

Jan 1, 1957

By CLARENCE WM. POY

THE most common difficulty faced by an engineer or mine operator when opening a new property in a new field is the lack of roads and of cheap transportation. This one item often swings the balance of success or failure in starting a project. In Alaska, as elsewhere, such problems are more or less serious. In the boom days around the Valdez district, as well as in other parts of this territory, freighting was accom¬plished by dog teams or horses, or even by men that were willing to put their shoulders into harness, because there were virtually no roads. More important, there was only one time when supplies could be transported, and that was when there was suffi¬cient snow on the ground following a heavy wind. Then, and only then, could one depend on the snow to support horses and sleighs, and be sure that the gulleys, streams, and crevices in the glaciers were filled with snow to avoid pitfalls. These methods were used when one had no roads, no streams in the summer to float a barge, or even a trail for a pack train. If the snow was deep and soft, trans

Jan 1, 1935