Search Documents

By R. W. Kraft

A back- reflection precession-type X-yay camera for determining the crystallographic orientation of the crystallites of both phases in small areas of thick specimens of polyphase alloys is described ad the geometry, advantages, and limitations of the apparatus are discussed. Metallographic obseg-vations of interfacial angles (or habit planes or growth direction are made on the same specimen so that the crystallographic and metallographzc orientation data call be directly correlated. An example of the application of tile technique to a unidi-~~ectionally solidified CuA12-A1 eutectic specimen is presented. The interfacial planes ad growth directions of each phase were established, and the orientation relationship between the phases was observed and found to be approximately intermediate between two previously reported relationships. The crystallographic interfacial relationship between two solid phases is an important parameter in a variety of metallurgical phenomena because of the energy associated with the interface and because this energy is at least partly associated with the way in which the two space lattices are in contact along the interface. In order to describe the interfacial planes in the crystallites of both phases it is necessary to determine the crystallographic orientation of each phase in a specimen relative to each other, and to directly correlate these data with met-allographic measurements from which the interfacial planes can be determined on the same specimen. The back-reflection Laue technique is the easiest way to determine the orientation of thick single crystals or large grains and the method can be combined with metallographic techniques to provide the necessary data, provided the reflections from each phase can be distinguished from one another. However, if the crystallites are small or of varying orientation or if one or both phases has a unit cell with less than the maximum symmetry, many overlapping and complex Laue patterns are recorded simultaneously and it becomes impractical if not impossible to interpret the photographs. All of these complexities were present in a unidirectionally so- lidified A1-CuA12 eutectic alloy1 for which a crystallographic analysis was desired. Consequently the method described here was developed since no known X-ray or electron diffraction technique had all of the following attributes which were required. 1) Method should yield data from which the crys-tallographic orientation of every crystallite or diffracting unit in the irradiated area can be determined. 2) Method should be adaptable to the study of small areas. Depending upon the degree of preferred orientation in the specimens, it should be possible to obtain reliable data in a reasonable length of time on irradiated areas as small as 1.0 or even 0.1 mm in diam. 3) Method should permit direct correlation of crystallographic data with microscopic orientation data pertaining to crystallite axes, habit, morphology, and growth directions as determined by optical microscopy. 4) method should be such that selected areas of large specimens can be easily studied. Trepanning of a small specimen (such as an electron microscope specimen) from larger specimens was undesirable since it would greatly increase the problem of correlating the crystallographic and microscopic directional data. Requirements 3 and 4 dictated that an X-ray back-reflection pinhole technique should be used on large samples, such as metallographic specimens which had previously been examined and analyzed for their microscopic characteristics. Similarly, requirement 2 could be satisfied by choosing a collimator of appropriately small diameter. Exposure times would not be excessive provided the detector were close enough to the specimen. Because of space limitations film was chosen in preference to a Geiger counter. Requirement 1 was fulfilled by using monochromatic radiation and providing enough additional degrees of freedom in specimen rotation to compensate for Bragg law restrictions on diffracted beams. DESCRIPTION OF APPARATUS The apparatus shown in Fig. 1 consists of a pin-hole collimator, (a), projecting through a rotatable circular film in a holder, (b), which records X-ray reflections in the back-reflection region. The specimen, (c), is mounted on the end of a shaft, (d), which is provided with an adjustment, (e), so that the specimen surface can be placed accurately on

Jan 1, 1962

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems. It is equally important to realize that most coal mines will require one or more conventional loader setups in the plan of total mechanization. Seam variations, adverse physical conditions, and special designs of main headings for haulage and ventilation, to name only three reasons, may render 100 pct use of continuous miners uneconomical. Of course, this situation may change. In one mine, prior to 1954, machines that ripped coal from the face achieved only average results, as compared to the impressive performance of boring-type units in another coal mine. A boring-type unit was therefore selected for the first mine in the belief that the chance of success would be greater if it were used in a combined cutting and wedging operation, cutting a full face in its forward movement. The miner was located in a part of the mine where a special projection could be readily developed, a solid area scheduled for mining according to the overall progress plan. All openings surrounding the particular area were carefully investigated for the presence of sulfur balls. Fig. 1 (opposite) shows the representative seam section, containing the several pyritic bands 1/4 to 1/2 in. thick; a characteristic Pittsburgh seam parting averaging 5 to 6 in. of slate, coal, and slate; and the occasional py-rite lenses 2 to 3 in. thick. Under normal conventional mining methods, the top 10 or 12 in. and the bottom 4 in. are left in place to offer roof protection

Jan 1, 1958

By R. S. McClellan

DURING the last year or so, with higher prices for gold and silver, many old properties in the West have come back to life. Almost every profitable producer in the old days has been considered, and the reasons for its shut-down investigated. If it seems likely that modern ore-finding, mining, and metallurgical methods, and S35 gold can again put the property on a profitable basis, someone can usually be found to back the venture. Methods of rejuvenation vary with the property, of course, but the following outline of what has been done with one group of mines in Idaho is fairly typical and may be suggestive to others. The Golden Chariot gold-silver properties, near Silver City, consist of seven old mines, working a vein system striking north and south, which had a productive length of some 3500 ft. The vein is a quartz-filled fissure with granite walls. Gold occurs in native, and with silver in the form of electrum which is the natural alloy of the two metals. Silver also occurs in a variety of sulfides. From 1064 to 1876, these old properties were worked intensively to an average depth of about 700 ft., through seven shafts which range in

Jan 1, 1934

By David B. Brooks, William A. Wallace, James R. Dunn

As the conflict between the mineral industry and preservationists steadily increases, it becomes urgent to determine as precisely as possible the costs of developing vs. not developing our domestic mineral resources so that enlightened mineral policy decisions can be made. A simple discounted cash flow equation is suggested as an approach to assigning a public-interest dollar value to mineral resources. Present value of a piece of land underlain by a mineral resource is taken as equal to the discounted cash flow derived from the resource corrected for present and future surface land values. The equation is effective as a base for mineral aggregate resource planning for metropolitan areas if transportation cost differences are substituted into the cash flow component. Suitably modified, the equation can be fitted readily into an existing computer simulation program for aggregate mineral resource planning in metropolitan areas. However, because of the lack of accurate input, the equation is less effective for other mineral commodities such as base metals and coal. Nevertheless, within a somewhat philosophical context, the equation still has utility and is effective in defining the problem of public interest values for minerals other than mineral aggregates.

Jan 1, 1972

By W. T. Cardwell, R. L. Parsons

This paper discusses the practical problem of estimating a single equivalent permeability for an oil reservoir, or a portion thereof, whose actual permeability varies in an irregular manner. Limiting averages for general types of permeability variation are developed, and illustrated by examples involving important, specific types of variation. Introduction The theory of the flow of fluids through porous media1"4 is becoming increasingly important in predictions of oil-reservoir behavior. In practical applications, however, reservoirs are seldom found to which simple theory strictly applies. Actual reservoirs have complicated shapes and nonuniform permeabilities and porosities. This paper discusses the problem of estimating a single equivalent permeability for an oil reservoir, or a segment of an oil reservoir, whose actual permeability varies in an irregular manner. The equivalent permeability of a reservoir segment is defined as the permeability of a homogeneous segment of the same dimensions that would pass the same flux under the same pressure drop- It is the permeability value that can be used in simple theoretical formulas to calculate the reservoir behavior. To the authors' knowledge, previous theoretical calculationst on systems of nonuniform permeability have been carried out only by Muskat'"; and he has not dealt with irregular variations, except in writing down the general differential equation for the pressure in variably permeable systems.lb In practical work, many calculations necessarily have been made to estimate equivalent permeabilities from the permeabiiity profiles obtained by core analyses. Regarding such calculations, Johnston and Sherborne6 say: Simple arithmetic and weighted averages have been tried on many wells and it has been found that, where frequent sampling has occurred, the arithmetic average is as satis- factory as a weighted average. It is possible that the application of statistical methods to the analysis of permeability data as recently presented by Law8 may prove fruitful. L,, has made a valuable contribution in showing how statistical analyses may aid in picturing the characteristics of a reservoir from those of a necessarily limited number of core samples. It is believed however that the particular problem of the estimation of equivalent permeabilities can be most directly approached from a fluid dynamical viewpoint as given in the present paper. An example is presented of the use of the conclusions herein in conjunction with Law's method. Theory In order to approach the problem of heterogeneity simply, it is interesting to consider a square block composed of four smaller, homogeneous, square blocks of porous medium, two of which have a

Jan 1, 1945

By R. N. Upadhyay, M. Maleki, I. Fatt

Conventional laboratory core analysis tests on samples of two limestone reservoir rocks indicate that about 20 per cent of PV is in dead-end pores. These tests (electric logging formation factor, mercury injection capillary pressure and miscible displacement) were carried out on 1/4-in. diameter test plugs. Test results show a clear dilference between these samples and sandstone or homogeneous limestone reservoir rock. Although the amount of dead-end pore space can be only roughly estimated, the presence of such pore space seems clearly indicated. Pressure transient studies also show presence of deadend PV. Although they do not give quantitative results, pressure transient data yield a reasonable estimate of the size of the neck connecting dead-end pores to the main flow channels. INTRODUCTION Equations conventionally used to describe reservoir flow behavior contain the implicit assumption that all connected pore spaces contributed to both porosity and permeability. Several authors3-7 have pointed out the changes in pressure transient behavior and in electric log interpretation that may result if this assumption is incorrect and, instead, dead-end or cul-de-sac pores are present. There is a need for laboratory tests that can detect presence of dead-end pores in core samples. With such information on hand the petroleum engineer can make more rational use of the mathematical tools now available for analysis of reservoir flow behavior. This paper describes laboratory studies designed to detect and, if possible, give a quantitative measure of dead-end PV in laboratory-size core plugs. Three reservoir rocks were used, two of which were limestones suspected of having deadend pore spaces and a well-known sandstone, used as a comparison standard, in which there is believed to be little or no dead-end pore space. All the studies were designed to measure the natural dead-end PV; i.e., the pore space which is dead-ended because of rock structure. During multiphase flow in a rock without dead-end pores, some parts of one of the phases can become surrounded by the other, thereby giving (for certain flow behavior) an effective dead-end pV8,9. Such behavior will not be described here.

Jan 1, 1967

By Wiley C. Buford

Gary Works No. 1 BOP Shop is a three furnace shop which went into operation December, 1965. The heat size is over 200 tons, with a substantial percentage of the production used to feed a Continuous Slab Caster. Vessels are driven by a shaft mounted bull gear and main housing utilizing eight 35 HP flange mounted motors and primary gear reducers. Torque absorption is controlled by two spring actuated torque arms. At 1:00 p.m. on Thursday, August 6, 1970, as "E" furnace was being turned down for a preliminary test, the drive side trunnion bearing failed. The furnace dropped slightly and shifted several inches north in the direction of the drive unit. The decision was made to tap the heat which was done without incident and the vessel uprighted. No attempt was made to completely drain the slag from the vessel, so as to avoid any further damage to the trunnion shaft bearing surface. The bearing failure occurred approximately four years and eight months after start up of the shop. Unfortunately ?M? furnace had gone down for a normal reline two days prior to the bearing failure, leaving the shop with only one operating furnace.

Jan 1, 1972

By A. A. Janke, G. J. Vogel, W. M. Swift

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations, and design studies are being carried out by various organizations under contract with the Department of Interior (Office of Coal Research, OCR) and with the U.S. Environmental Protection Agency, (EPA). The Atomic Energy Commission's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. The principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process are covered in this paper. The participants in the multiorganizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1976

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".' that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951

By M. E. Wadsworth, G. W. Warren

INTRODUCTION Hydrometallurgical processes for the extraction of metal values can be divided into two broad categories: (a) Processes involving the treatment of high grade material (e.g. finely divided mineral concentrates); and (b) processes which treat lower grade material (ores, waste dumps, etc.). This discussion will be directed primarily toward the first category, but in either case a fundamental knowledge of the intrinsic kinetics and thermodynamics is necessary to understand the behavior of the system. The bulk of research efforts in the last decade along these lines has been aimed at the recovery of copper (1-8). However much information has also been reported on uranium (9, 10) , zinc (11) , cobalt and nickel (12, 13). More comprehensive reviews on these areas are also available (14). As discussed by Sepulveda and Herbst (15, 16) one of the most difficult problems facing process designers is the acquisition and scale-up of reliable information concerning the intrinsic kinetics of leaching systems. The scale-up or modeling of these multiparticle systems is far more complex than that of homogeneous ones. This is due to the numerous rate determining steps which are possible with heterogeneous reactions and the broad distribution of properties of a multiparticle feed such as particle size and mineralogical composition (16). In addition, other factors must also be considered such as interactions between particles, the anisotropic nature of individual particles, the effect of solution chemistry, and electrochemical phenomena. All of these factors must be taken into account, often simultaneously. The thrust of this paper will be to more closely examine how the factors mentioned above can be treated. Some elementary examples of

Jan 1, 1980

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By R. T. McLamore

Lack of sufficient native permeability or skin damage caused while drilling wells for in situ leach mining projects may necessitate stimulating injection and production we1ls to increase the leaching rate to economic levels. Such stimulation processes could include acidization, hydraulic fracturing, or explosive fracturing. This paper describes an explosive fracturing process that is being developed primarily to stimulate the production of oil and gas wells, but may be useful in in situ leach mining projects as well. The process utilizes a liquid explosive that has unique safety features. The chemicals that form the explosive are subdivided into two pumpable, non- detonable components. Technology has been developed to pump these two components independently but simultaneously into the well and blend them together downhole to form the explosive. As such, surface facilities and personnel are not exposed to explosive hazards. The explosive formulations utilized in the process have been subjected to numerous safety and characterization tests and been qualified for use in deep wells with temperatures and pressures up to 250°F and 10,000 psi. The explosive composition can be varied to produce an explosive ranging, energetically, from a blasting agent to a high explosive that can be detonated after injection into a borehole, a porous media or into thin naturally occurring fractures within the roc

Jan 1, 1974

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By R. Wiesenthal

A method is developed for improving the low recovery efficiency which results when viscous oils are flooded by water. Viscous oil has been diluted with a lighter liquid miscible in it in any ratio which produces a mixture possessing a reduced viscosity and which is then displaced by water. Light gasoline was used in these tests to reduce the viscosity of the oil in place. Oils possessing viscosities in the range of 1.28 to 324 cp at the test temperature of 30C were displaced from a cylindrical unconsolidated sand core, with a length of 2 m (6.6 ft) and a diameter of 10 cm (3.9 in.) at a flood of 6.27 cc/sq cm/hr. In two test series up to I PV of light gasoline was injected into the core before water flooding. In the first series the recovery of a low-viscosity oil (1.28 cp) increased as the volume of light gasoline was increased. However, only the oil which could not be recovered by water flooding alone could be replaced by the light gasoline. In the other series, the recovery of a more viscous oil (13.5 cp) was not increased even if large quantities of light gasoline were injected. An oil bank built up ahead of the water front so that the flood water met with equivalent saturation conditions, as would be the case in flooding solely with water. However, the recovery of more viscous oils could be increased substantially when the core was first flooded with water, followed by a slug of light gasoline, and then flooded with water again. Furthermore, an oil bank ,built up ahead of the second water front. The formation of this oil bank is particularly favorable for the displacement process; the greater part of the light gasoline injected was pushed out of the core ahead of the oil and recovered. Using a light oil of low viscosity, it was possible to replace only the residual oil that could not be recovered by water flooding by the light gasoline. As the basic study had shown that highly viscous oils could be recovered by flooding first with water, then with light gasoline, followed by a second injection of water, the study was extended by tests made with reservoir fluids and cores taken from the low-gravity oil reservoir of the Wietze field, Germany. A great increase in recovery over flooding with water alone was obtained in these tests. The results may show a way to recover high-viscosity oils by a comparatively simple flooding procedure. INTRODUCTION In fields where oil recovery has not benefited from natural water drive, increased recovery may be obtained by the injection of water into the reservoir, especially in the case of fields which produce high-gravity, low-viscosity oil. There is a rather close relation between the viscosity of the reservoir fluid and the recovery that can be obtained by water flooding. As the viscosity increases the oil recovery decreases proportionately, so that an oil viscosity about 30 times that of water is generally considered to be the upper limit for an economically successful water flood.' This limitation has been recognized theoretically by Buckley and Leverett,' and has been verified by numerous laboratory flooding tests, such as by Croes and Schwarz,V n the viscosity ratio range of oil to water from 1 to 500. The reason for the inferior recovery of viscous oils by water flooding can best be understood by considering the mechanism of flood tests. In such tests water is introduced into one end of a sand-packed tube which is saturated with oil of the viscosity to be tested, and oil is produced from, the other end. Oil, with a viscosity lower than that of water, is pushed ahead of the advancing water with considerable uniformity, and irregularities in the displacement process tend to be eliminated as the oil saturation decreases and the water saturation increases. However, oil recovery is not complete, for the water forms interfaces with the oil and traps residual oil droplets in certain of the pore spaces. These residual oil droplets are distributed rather uniformly through the sand, and they are not susceptible to recovery regardless of the amount of water passed through the test cylinder. In the case of an oil possessing a viscosity greater than that of water, the injected water tends to move irregularly through the sand in the test cylinder. At the place in the sand where initial water movement takes place, resistance to the movement of water is lowered and the water finger so formed will grow perceptibly; it will extend to the outlet end of the test cylinder so that a breakthrough of water takes place long before much of the oil-saturated volume of the sand has come in contact with water. Once the breakthrough of water takes place, the water-oil ratio is gradually approaching the economic limit, even though much of the oil in the test cylinder remains unaffected by water. Disconnected drops of oil are trapped in the portion of the sand that has been invaded by water, just as when an oil of low viscosity is flooded. The poor recovery of the more viscous oils, therefore, is due to the irregularity of water movement through the test cylinder, and the rate of water movement through restricted sections of the oil-saturated sand increases with the more viscous oils. There are three ways whereby the recovery of viscous oils by water flooding can be improved:' (1) adding materials which will increase the vis-

Jan 1, 1965

By Dorsey A. Lyon, Robert M. Keeney

The utilization of hydro-electriic power in electro-metallurgical industries, aside from purely mechanical operations, may be of two kinds. The electric energy may be used to supply the heat necessary for the performance of the chemical reactions of a metallurgical process, or the electrolytic action of a direct current may be employed for extraction of metals, either in a reduction process or a refining process. In discussing this subject, it is well to distinguish between established industries, which are producing metals and alloys at a, profit by use of the electric current, and the many processes which are either still in the experimental stage or have not even passed the paper stage of development of a patent. That is, we consider electro-metallurgical industries as commercial operations which are now consuming large blocks of electric energy, while processes which are not in commercial operation are only prospective consumers. Also, owing to the difliculty and risk of any attempt to foresee the effect of the European war upon electro-metallurgical industries, we have felt obliged to disregard the war entirely, and state our opinions regardless of its existence. Application of Electric Energy to Metallurgy Disregarding electrolytic refining processes, the applications of electric energy to metallurgy, when considered from a commercial viewpoint, may be classified as follows: Industries Experimental Processes Manufacture of aluminum Electric-furnace smelting of: Electric-furnace manufacture of: Ferro-alloys Copper ore Pig iron Zinc ore Steel In this paper only the above industries and experimental processes will be considered as possible consumers of hydro-electric power in large quan-

Jan 1, 1916

By O. P. Chisholm

Dross emerges from the blast furnace either with the lead through a lead well or by tapping from a forehearth or settler, but until a dozen years or so ago few dross reverberatories were used in western lead smelters because it was the usual procedure to circulate the dross from the drossing lead kettles back to the blast furnace. It was quite customary for lead smelters to produce matte in their blast furnaces, as this was the form in which copper could be collected, concentrated if necessary, and shipped to the copper smelters for further treatment. The main prerequisites for good matte formation arc., of course, a more or less definite amount of copper on the charge and sufficient sulphur. Such troublesome impurities as arsenic and antimony were ignored, in so far as possible, although they contaminated the bullion and thereby increased refinery costs. At the same time stocks of blastfurnace speiss containing gold, silver, lead and copper in addition to iron, arsenic and antimony, were being accumulated for want of a market to absorb them. As the dross was being fed back to the furnaces as rapidly as it was being produced, arsenic and antimony tended to build up until the arsenic could effect a combination with copper and iron and an alliance with lead, and the antimony a combination with copper and an alliancc with lead. Sulphur, being the most active agent in taking up the copper, left little of that element for the arsenic and antimony, so that on the whole a somewhat unsatisfactory metallurgy resulted. During this same period, certain lead plants were beginning to encounter trouble with zinc due to the replacement of crude ores of lot zinc content by concentrates containing high percentages of lead and zinc in sulphide form, the blast-furnace slags resulting from the smelting of such concentrates being characterized by a decidedly increased zinc content. It was soon realized that zinc plus sulphur was "poison" to a lead blast furnace and steps were taken to reduce the sulphur content,. At this stage some plants found that any substantial matte fall was out.

Jan 1, 1937

By Frederick L. Knouse

THE south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19° to 21° and 30" south latitude; and from 40° to 41° and 30" west longitude. This includes the central part of Espirito Santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Martines, Espirito Santo (Fig. 1). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through Vitoria; and by the E. F. Minas-Vitoria and E. F. Central do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatites, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. EARLY OPERATIONS Mining of quartz crystal in this region began in 1928, and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crystal as small as 10 grams. Since 1941 only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of loo grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, or Domingos Martines, Espirito Santo. Marketable quartz crystal was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large cores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. PRODUCTION The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1946

T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Mr. Killian is to be commended for his inquiry as to why a decrease of 15.3 pct in coke consumption was accompanied by a decrease of only 1.9 pct in the CO/CO, ratio of the top gas. Although I encouraged him in his efforts to find a more significant and meaningful carbon-gas ratio, the method, calculations, and conclusions originated entirely with the author. Whether we agree entirely with the assumptions underlying his corrected ratio, I think we can all agree that a better ratio is needed, and that he deserves credit for recognizing the need and for doing something about it. To be most useful, the CO/CO, ratio for the top gas should reflect the way in which the carbon is gasified in the furnace, particularly the degree of oxidation and the extent of heat release. The effect of CO, from the decomposition of the limestone and the effect of the reaction of CO and water vapor in the upper part of the furnace on the quality of top gas should be isolated from the effect of more basic reactions such as ore reduction and solution loss. The reduction of sufficient iron oxide to produce a ton of pig iron and the accompanying changes in the proportions of the carbon gases can be expressed on a mol basis as follows: 16.5FeA + 16.5CO - 33FeO + 16.5CO, [1] 33FeO + 33.0CO = 33Fe + 33CO. [2] The CO, from eq 1 normally escapes from the furnace because it does not react with coke at the temperature of its release. However, as much as 50 pct of the CO, from eq 2 may react with coke because it is released at temperatures above 1000°C: 16.5CO. + 16.5CO2 = 33CO [3] Thus we see that the gasification of 16.5 mols or about 200 lb of C in solution loss will regenerate as much CO as is required for the last stage of reduction. The pronounced effect of reaction 3 on the final proportions of CO and CO, in the gas stream is obvious. It also follows that reaction 3 materially alters the heat release but it cannot be entirely eliminated in Lake ore practice. A previous study indicates that 100 lb of solution loss may be necessary to maintain the reducing power of the gas. A reduction of 100 lb from the normal level of 200 lb would mean that over 1,-000,000 additional Btu are released in the process. The 100 lb of additional carbon which will be burned at the tuyeres will release 437,000 Btu and the absorption of 583,000 Btu by eq 3 would be prevented. One of the chief objectives of sized ore burdens and more uniform distribution of the gas stream is to minimize solution loss by completing reduction higher in the furnace and in turn to release the maximum amount of heat from the carbon charged. It was odd, indeed, to find that the use of sized ore and sinter in the careful tests reported by Dobscha had changed the CO/CO2 ratio very little. The author has stressed the close correlation between his corrected CO/CO, ratio and production. A correlation of fuel consumption and the CO/CO, might be more logical. Fuel consumption on the prepared ore burden decreased 15.3 pct whereas the corrected CO/CO2 ratio decreased 19.0 pct. Although this agreement between the reduction in fuel and the reduction in corrected CO/CO2 ratio is not as close as the correlation with tonnage, it indicates the corrected ratio is superior to the normal ratio which decreased less than 4 pct. Some adjustment should be made for the reaction: CO + H2O = CO2 + H2 —700Btu [41 because there is evidence to indicate that about one half of the hydrogen is formed in the upper 21 ft of

Jan 1, 1953

By J. W. Halley, G. L. Plimpton

BECAUSE of the two distinct stages in the solidification of rimmed steel, segregation in the rimmed ingot is more complex than that in the killed or semikilled ingot. In the earlier stage, chemical reactions, resulting in evolution of gas and vigorous stirring of the metal, effect a degree of negative segregation unique to rimmed steel. The composition of this zone constitutes the principal quality advantage of this type of steel. In the later stage of solidification, after the evolution of gas has ceased, the segregation follows the general pattern of a more completely deoxidized steel. However, the composition of the liquid remaining after the first solidification stage varies markedly from that of the original melt, some constituents having been partially removed as reaction products while the concentration of others has been intensified by rejection from the metal solidifying in the first zone. The aim, from the standpoint of segregation, in rimmed steel of high quality is to effect a maximum negative segregation in the rim zone without excessive concentration of undesirable elements at the center of the ingot. To achieve this aim, the composition of the melt may be varied and the furnace and pouring practice may be adjusted within certain limits. It is the purpose of this study to discuss segregation in rimmed steel from the standpoint of the mechanisms that produce it and to survey the phases of open-hearth practice that influence those mechanisms. MECHANISMS PRODUCING SEGREGATION The mechanisms that determine the degree of segregation in the rimmed ingot are closely interrelated, making it difficult to select the primary factors and to determine a satisfactory order for presenting them. For instance, the question of sulphur segregation is relatively simple, since sulphur is not directly involved in chemical reactions in the ingot; but its concentration in the rim zone is dependent not only on its original analysis in the melt, its segregation coefficient, and the freezing rate, but also on the rate of its removal from the impure film on the solidifying surface. This washing action involves all the factors (such as freezing rate, the carbon-oxygen product, pressure, etc.) that determine the rate of gas evolution and hence the efficiency of film removal. Sulphur distribution between the rim and core is affected by the volumetric ratio between the two zones, and its segregation in the core is a function not only of the freezing rate of the core but also of all the foregoing factors that determine its concentration in the metal when solidification of the core starts. To simplify the presentation, it is proposed to treat the mechanisms affecting segregation independently in this section, reserving a discussion of their over-all effects for the section in which actual segregation data are given. The factors affecting segregation will be treated in the following order: (I) differential solidification, (2) removal of constituents as

Jan 1, 1944