Search Documents

IT IS impossible to speak in exact terms of the effect that selective flotation has had, is having, and may have on the State of Utah. Its results enter into the economic structure of the state in so many ways and its ramifications are so widespread, that every line of industry is affected. Some effects can be definitely determined; others can be reasonably approximated; but the effect as a whole can not be set out in exact figures. Utah is essentially a mining state; mining is its basic industry and always will be. Agriculture, equally a basic industry, and of course, equally vital, can be practiced on only 6 per cent. of the 85,000 square miles of its area. It follows, therefore, that the economic future of this state depends upon a development of its natural resources. About 6 or 7 years ago, the mining industry in Utah was at a low ebb. This condition was caused partly by postwar conditions and other temporary causes, but prevailed also, which was most important, because the direct-smelting ores of the state were being rapidly exhausted and the cost of treatment of complex ores was almost prohibitive. Furthermore, the wet concentration of low-grade ores was unsatisfactory and did not result in producing a good smelting product. On visualizing this situation, one of the large smelting companies in the valley had the courage, ability and faith to develop and expand the principles involved in selective flotation of complex ores. This example has been followed by other smelting and reduction companies and the result has changed the entire aspect of the mining industry in Utah. The utilization of the zinc in the low-grade, lead-zinc-silver ores was the principal problem to be solved. The average yearly production from the State of Utah for the 10 years beginning 1914 and ending 1923, was something less than 10,000 tons of zinc concentrates. This period includes the world war, when abnormal prices stimulated production. In 1924, selective flotation began to be practiced on a considerable scale, replacing concentration by gravity and bulk flotation which had been used generally until this time. PRODUCTION AND VALUE OF ZINC CONCENTRATES The production of zinc concentrates during 1924 was approximately , 24,000 tons, or twice the average yearly production of the previous 10

Jan 1, 1928

By C. K. Leith

1 apologize for attempting to talk in a field in which 1 am by no means a specialist, but some of the problems brought up have much in common with other minerals. It touches the field in which we are all interested and it is a field in which our Mineral Inquiry has been giving special attention during the last two years. While it is the primary business, of course, of this Institute to consider the physical facts and technology of minerals, we now face the necessity of considering the minerd industry in its broader economic, social, and political relationships. We have run into a traffic jam—as though a load of hay had been spilled on the road. It makes no difference whether we are drivers or passengers, technical or nontechnical men, we have to get the load off the road before we can go farther. We are conscious of very many difficulties which are outside of the ordinary range of cost accounting or methods of mining or the usual thing with which we concern ourselves. We have extensive readjustments to make in our social and economic and political contacts. It is up to us to find out what is the matter. As a matter of fact, we do not know what is the matter in any comprehensive way. We have many suggestions as to difficulties here and there. Many people are working on the problem, but when the mineral industry as a whole is asked what is a reasonable course of procedure, what is its program, what would be a reasonable state or national policy, I think you will agree with me that we have no spokesman able to outline even a semblance of such a general policy. We sit back and criticize when somebody else steps in, as Governor Murray stepped in, and as many others of our state governors and legislators are stepping in, to do things which we do not think are reasonable. When they say, "What is a reasonable program? " we find ourselves caught napping. We have not agreed on a program. The other day in talking with one of the leaders of the western radical movement, I was twitting him on having no sound and comprehensive conservation program. He said, "What is yours, and what is the program of the mineral

Jan 1, 1932

By E. G. Leonardon, Irving B. Crosby

ElectRical prospecting by potential methods has been applied to mining problems for some years and determinations of the depth to bed rock have been made, but so far as is known it has not been used previously in the solution of civil engineering problems, such as investigating the foundations of dams. During the past winter and spring the senior author has been engaged as consulting geologist in studying the site of a large dam on the upper Connecticut River and has had the satisfaction of introducing electrical prospecting to foundation problems. The valley across which the dam is to be built is underlaid by a deeply buried preglacial gorge which is filled with glacial deposits. An extensive drilling campaign was in progress, but the work was unusually slow and expensive on account of the number of boulders in the overburden. The necessity of speeding up the work was pressing and it was decided that much of the needed information could be obtained by geophysical methods. After investigating the various methods and conferring with the company engineers and with the consulting engineer, Albert Crane, a contract was made with the Schlumberger Electrical Prospecting Methods, and an observer with apparatus was sent to the dam site the first of April, 1928. The problem was to determine the depth to rock at various points in order to prepare a contour map of the bed-rock surface and outline the buried gorge in the vicinity of the dam site. Over one hundred determinations of depth have been made and the bed-rock topography is now known in considerable detail. In addition, some information has been obtained about the nature of the overburden. The drilling has been continued; in fact, two additional drills have been put to work, and the electrical determinations have been checked at several points. At one of these the depth to rock given by the electrical work was 142 ft. and the drill found rock at 147 ft., an error of less than 4 per cent. The electrical work has also been checked by the geological study, and it has been found that when the electrical determinations are in agreement with the geological expectations they are probably reasonably accurate. When the electrical interpretation of the subsurface topography is incon-

Jan 1, 1929

By I. S. Servi, N. F. Graves

THE etch-pit technique has long been used to reveal low-angle boundaries and, in general, the distribution of dislocations in high-purity metals. Often this technique is amenable to quantitative computations,' but generally is affected by some degree of uncertainty because etch pits can be nucleated not only by dislocations, but also by inclusions and surface imperfections. In the case of high-purity zinc, Gilman' reported that etch pits were produced only after adding 0.1 atomic per cent of cadmium to the crystals and aging at a proper temperature. In the course of a study of low-angle boundary behavior in zinc crystals, etch pits were produced in 99.999 pct zinc without resorting to intentional contamination, by etching in a 50:50 HNO3H2O solution. The technique consists of etching until the heat of reaction brings the solution to a boil, and in displacing the etchant rapidly with a stream of cold water, thus avoiding staining. The undesirable features of this technique are the heating effect and the removal of a considerable amount of material. A high polish is obtained if staining is controlled properly; therefore, the etch pits appear very clearly and with excellent contrast when observed under dark field illumination. This is especially helpful for cursory examinations at low magnifications. Several observations were made on zinc crystals of square cross section, having one face parallel to the basal plane and one edge parallel to a slip direction, Fig. l(a). When such a crystal was bent about 2" over a glass die and annealed at 390°C, a sharp boundary was formed only in the inner portion of the crystal. Near the two prismatic faces, perpendicular to the basal plane, the boundary was always branched into many lower-angle boundaries, Fig. 1(b). Attempts to move the main boundary by applying a shear stress to the specimen invariably resulted in curving the boundary, the branched ends remaining pinned in their original location, Fig. 1 (c). The prismatic face, when etched as indicated in the foregoing, revealed the existence of numerous (sometimes up to 30) fine boundaries, nearly parallel to each other. Pre-existing lineage boundaries, generally parallel to the direction of growth, were barriers to the formation of polygonization boundaries and interrupted the continuity of the substructure, Fig. 2. Twin

Jan 1, 1959

THERE have always been in this world men of such keen intelligence that with their discourse they have been capable of infinite and various inventions that are as beneficial as they are simultaneously harmful to the human body. Wherefore, from day to day, we see unfolded before our eyes some of these that greatly astound our minds, and we remain so stupefied that when-we think of them we are not able to control our faculties for some time, both from considering by what necessity or purpose these men were goaded, as well as from contemplating the profound subtlety of their discoveries, which, in truth, are such that they are awarded the greatest commendation by noble minds. By following their counsels and with their aid, there have been* some astute and lever captains who have had certain pots or balls of earthenware carried by their infantry, expressly filled with compositions of powder or other unctuous liquors disposed to ignite easily. When they meet the enemy in battle and come up close to them, they try to strike vigorously with these in the first assault in an effort to throw them into disorder and to make them give way by breaking them up and drawing them out of formation. The smoke is harmful, but the fire very much more so. These are made in this way. Take the number of vessels that you have to make-it does not matter whether they are raw or baked as long as they are well freed from the moisture of the clay-and fill them a little more than half full with coarse gunpowder which has mixed in it pounded Grecian pitch and at least a third of crushed sulphur. Then pour in a covering a dito thick of strained pig fat mixed with powder. This keeps it from falling out when it is thrown and keeps the fire slower until it reaches the enemy. When this has been made, open up the pig fat a little at one side when you wish to throw it and put in a little fuse or a little good powder and apply fire, holding it in your hand until you see that the fire has taken hold well. Then throw it, choosing your time. A liquid composition is also made in a kettle in which are put pork fat, petroleum oil, oil of sulphur, live sulphur, [163] doubly refined saltpeter,

Jan 1, 1942

By Charles J. McMahon

In a recent paper, Floreen and Hayden report that additions of the noble metals iridium, rhodium, ruthenium, and platinum to Fe-C alloys containing 0.03 to 0.08 wt pct C act to significantly reduce the ductile-to-brittle transition temperature in a notched-bar impact test. They compare these results with the similar, well-known effects of nickel and manganese additions, and they note that this supports the hypothesis that addition of austenite stabilizers enhances notch toughness. Although not attempting to offer an explanation for this, they suggest that it might be found in an alteration of the bonding characteristics of the bcc lattice of iron by additions of elements which tend to stabilize the fcc lattice. While this suggestion appears to have some merit, it should perhaps be held in abeyance until two more likely possibilities have been explored. It is now fairly clear that the beneficial effect of manganese derives from its ability to promote a globular carbide morphology instead of the platelike form found in grain boundaries and pearlite patches in Fe-C al10~s.' Previous work14 has also shown that cleavage fracture in Fe-C alloys of the type tested by Floreen and Hayden originates almost exclusively in the cracking of cementite platelets, and that the ductile-brittle transition temperature is very sensitive to the volume density and size of these carbides. Treatments which lead to development of nonlamellar carbides or fine dispersions of carbides, such as quenching and tempering or appropriate alloy additions, promote toughness by removing the primary mode of cleavage initiation. The effectiveness of manganese in this regard has long been known. Nickel appears to behave in a similar manner, though the effect is perhaps not as dramatic as with manganese.15 However, nickel additions do lead to a definite refinement of ferrite grain size following a given transformation heat treatment, and this in itself acts to greatly enhance notch toughness.'' (The grain sizes of the various heats tested by Floreen and Hayden were not reported, so it is not known how much influence this factor exerted in their results.) In conclusion, it is suggested that one should consider the well-established effects of alloying elements on carbide morphology and ferrite grain size before resorting to more complex possibilities, such as modification of interatomic bonding.

Jan 1, 1969

Discussion of the paper of EZEQUIEL ORDOÑEZ, presented at the Pittsburgh meeting, October, 19.14, and printed in Bulletin No. 94, October, 1914, pp. 2531 to 2536. DAVID T. DAY, Washington, D. C.-Dr. Ordoñez is really the pioneer in the study of the occurrence of Mexican oil. His studies came at such an early time as to prove really prophetic. He was successful in pointing out the relationship of these oil deposits to the volcanic teeth which are so very characteristic as a geological feature in the coastal plain of Mexico. At that time only the first wells around Ebano had been drilled, and drilled under the direction of Dr. Ordoñez himself. Only these Ebano wells were available for a real study of the condition of the occurrence of oil, the other large gushers not then being known. From that time on, the study of the geology of the country has, in large measure, been able to keep up with the oil development. As usual, a great deal of haphazard work in the exploration of the oil fields has been carried on. The results have been good, bad, and indifferent. We know a great deal more about the distribution of oil in Mexico than we do about the geology of it. Two ideas have become prevalent in regard to the Mexican oil, due to the peculiar development there: (1) That oil is omnipresent over a tremendous area bounded by De Soto La Marina, in the province of Tamaulipas, on the north, to south of Tuxpam in Veracruz; and (2) that there are very few spots in all this region which have rich gushers. The truth is somewhere between the two. The amount of land taken up, chiefly by three or four large companies, is extremely great, and covers all the possible chances. The idea that oil is going to be discovered in a large percentage of the land taken up by the oil companies, seems to me entirely unjustified. The amount of oil that will be produced from comparatively small spots here and there over that territory and other territory, undoubtedly will be very great. I do not think there is any hope of multiplying the capacity of these large gushers by the area of that part of Mexico in which they are contained, as a, large number of promoters are inclined to do.

Jan 4, 1915

By J. R. Long, T. R. Graham, C. W. Matthews, R. S. Dean

IN a previous paper§ the authors reported on the mechanical properties of a 65 per cent copper, 10 per cent manganese, 25 per cent zinc alloy as compared with similarly processed cartridge brass. Additional investigations by these laboratories, on higher copper alloys, have demonstrated that at lower zinc concentrations even larger amounts of pure manganese may be added to copper-zinc alloys without exceeding the single-phase solid solution limits, and that similar increases in tensile strength, yield strength, and hardness may be obtained without excessive decreases in ductility. Several compositions in this range showed also a decided color change with increasing manganese. The normal "brassy" color was considerably lightened and reduced to a faint yellow cast at 15 per cent manganese. With higher manganese contents the alloys were essentially white and similar in appearance to the nickel-silver alloys. From this work it appeared that it would be desirable to determine more completely the properties of the wrought and annealed white alloys. Accordingly, a more detailed study was planned of an alloy having the composition 70 per cent copper, 20 per cent manganese, and 10 per cent zinc. This alloy remained single-phase throughout the working and annealing cycles of the preliminary tests and appeared to be about the strongest of the white single-phase alloys. The project included also an investigation of additional alloys, deviating from this composition by 5 per cent of each of the three components to evaluate the effects of variation in composition; also a study of the properties of the central alloy made with silicothermic manganese. MATERIAL PREPARATION Electrolytic manganese, wirebar copper, and electrolytic zinc were used for the preparation of the alloys. Representative analysis of the electrolytic manganese seldom exceeds 0.01 per cent iron, 0.02 per cent sulphur and 0.02 per cent lead, with no silicon or aluminum. A typical sample of the silicothermic manganese metal contained 2 per cent iron, 0.81 per cent silicon, 0.i6 per cent carbon, and 0.36 per cent aluminum. Melting and alloying were performed in a high-frequency furnace with magnesia crucibles. Melts were deoxidized with small aluminum additions and cast into 25-lb. slab ingots. Care was exercised in deoxidation to avoid excessive amounts of residual aluminum, which has been found to have significant effects on alloys in this system. All ingots were hot-rolled at 1200° to 1300°F. and then cold-rolled with intermediate anneal-

Jan 1, 1945

By C. F. Austin

lined-cavity shaped charge is an explosive mass with a cavity at one end and the detonator at the opposite end. The cavity is lined with a dense material, such as metal, glass, or a ceramic. Such an explosive device can be a useful drilling tool. Lined-cavity shaped charges are constructed to do just one thing — create a high-velocity jet of liner particles that can bore a hole in a target. The liner must be smooth and symmetrical, and high-velocity, high-brisance explosive must be used rather than ordinary commercial dynamites. Since the depth of target penetration is related to jet length, a standoff distance should be provided to hold the charge a short distance from the target. This allows the jet to lengthen prior to target impact. The best results are obtained when the jet is perpendicular to the target surface. Charges can be positioned for firing by taping them to a stake or simply laying them on a flat surface at the proper distance and angle with respect to the target. EFFECTS ON THE TARGET When a jet strikes a rock target, the jet and target particles at the jet-target interface move outward radially with respect to the jet axis to create a tremendous compressive load on the target material immediately below the target surface. The result is a shallow crater formed by spalling at the point of target entry. After cratering ceases, the steadily deepening hole continues to form as a result of the jet's imparting radial motion to the target particles at the jet-target interface. These radially moving particles collide with one another and with the hole walls, the net motion of the spent jet particles and target particles being back out of the hole in an axial direction (the backblast). The backblast keeps the penetration free of debris during penetration, al- though loose surface rock often falls into the hole after penetration ceases. The sudden stress relief after penetration ceases sometimes results in minor hole-wall rebound, which can partially fill the hole. The hole bottom will taper as the jet velocity decreases, until the jet velocity is too low to maintain the backblast. At this point the remaining jet and the following slug material are simply packed into the hole bottom. HAZARDS INHERENT IN USE Air blast from the highly brisant explosives used in shaped charges can damage nearby structures

Jan 1, 1961

By Frank S. Gardner, Morris Cohen, Dara P. Anita

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By John H. Holloman

In recent papers, O'Neill,' Vivian, and Zener and Hollomon3 have reviewed some of the information concerning the relations between stress and strain during plastic deformation. Since further information has been obtained since these reviews were published, this paper attempts to further coordinate and amplify the knowledge concerning the plastic deformation of metals in simple tension. Ordinarily the results of tensile tests of metals are presented as graphs in which the load divided by the original area is plotted as a function of the percentage of elongation measured over some specified gauge length. The interpretation of graphs of this sort is limited, since the stress required to deform the metal at any stage of the deformation is actually the load divided by the instantaneous rather than the original area. Furthermore, each increment of the deformation is performed on metal that has been previously deformed, and, as pointed out by Ludwik,4 the strain could be more effectively defined: where e is the strain and AO and A are, respectively, the original and instantaneous areas. The results of the tensile tests can be more effectively presented and interpreted if the stress* (load divided by actual area) is .lotted as a function of the strain as defined above. A schematic curve of this type is presented as Fig. I. In a previous paper,6 the concept of Ludwik7 concerning the flow and fracture of metals was successfully employed to explain some of the puzzling results of notched-bar impact tests of steel. It appears that the use of this concept ii; very fruitful and should be kept in mind in any study of the deformation charactcristics of metals. Ludwik considered that a flow stress-strain curve of a metal was essentially a locus of points that described the stress required for plastic flow of an infinite numbcr of specimens, each with a different strain history determined by the preceding part of the flow curve Each of these specimens can also be considered to have a fracture strength. Uniortunately (or fortunately depending upon the point of view), all the specimens, except the one deformed to the fracture strain, flow and do not fracture. Even though the metals do not fracture, the concept of a fracture-strength curve seems

Jan 1, 1945

By Morris Cohen, Dara P. Anita, Frank S. Gardner

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By W. M. Baldwin, C. R. Johns

Cobalt is reported1,2 to scale in accordance with the Pilling and Bed-worth3 parabolic law: where w = weight increase per unit surface area K = constant l = time The reported values of the parabolic oxidation constant, K, in the temperature range 600 to 1100°C follow an Arrhenius type of equation as inspection of Fig 1 shows. According to Valensi's theory5 on the scaling of metals where multiple-layered scales (for example, MeX, MeX2, and others) are possible, this fact could be construed as indicating that a single oxide only is formed on cobalt in this temperature range. Since the single straight line extends above 920°C where only CoO is stable in air (see Fig 2) it might be inferred that this is the only oxide formed on scaling. Arkharov and Voroshilova10 have studied the scales formed when cobalt is heated in air in the temperature range 385 to 800°C and report that CoO is indeed found in the scale but that CoO4 is also found as an overlay and in increasing amounts in the lower temperature ranges. No quantitative data regarding the relative proportions of the two oxides were reported. Again in the light of Valensi's theory this would indicate that the straight line in Fig 1 would be expected to undergo an inflection at some point in the temperature range 385 to 800°C. Chauvenet2 has studied the oxidation rates of CoO to Co3O4 and has found this reaction to proceed parabolically with time but reports parabolic scaling rates which are considerably (about ten times) larger than the scaling rates of cobalt metal itself. This is difficult to explain in terms of Valensi's theory although a full discussion of the possible discrepancy cannot be made in view of the lack of sufficient data. These points made an investigation of the scaling behavior of cobalt in air an attractive study. Discussion of Results Relatively large (approximately 95 sq cm of surface area) samples of 0.020 in. thick electrolytic cobalt strip,* sanded with 2/0 paper, were heated in air in a cyclone type furnace. The samples were weighed before and after the scaling treatment. The weight increases so observed obeyed the Pilling and Bedworth parabolic law at all temperatures studied. The parabolic scaling constants when plotted on a logarithmic scale as a function of absolute temperature are reproduced

Jan 1, 1950

By Gerald Edmunds

IN a paper1 before this Institute in 1940, the writer reported that the surface orientation texture of zinc and cadmium differed from the texture existing within the casting, in that basal planes were parallel to the surface. He was unable to rationalize the origin of this surface texture. It is conceivable that the surface orientation texture is influenced by the atomic force fields, which are different at the surface and within the body of metal. It was considered that a radical change in the surface against which the metal is cast might alter the surface texture. In trial of this, zinc has been cast against a surface of molten lead, but the same result has been obtained-i.e., (001) parallel, ±20°, to the surface-as was obtained when it was cast against air, Transite or iron.1 Into the bottom of an open cast-iron tray, 7 by 14 in. by 2 in. deep, preheated to about 275°C., about ¼ in. of lead, then) ½ in. of zinc was poured, and the whole was covered with an electric heater to enforce freezing from the bottom upward. After a lapse of time sufficient for the zinc but not the lead to solidify, the zinc slab was raised free of the molten lead. The bottom surface of the zinc casting was coated with a thin layer of lead. A specimen of the slab 1 ½ in. square was metallographically polished to flatten it and remove the slight film of lead, and the orientation was determined by the method used before,1 with the result stated above. Some determinations have also been made on other metals, as follows: Surface orientation determinations were made on the 3/8-in. diameter grip section of two ¼ -in, diameter aluminum-alloy die-cast tensile bars and on a 1/8 by ½ -in. flat aluminum-alloy die-cast tensile bar. None of these three aluminum die castings exhibited any preferred orientation at-the surface. A brass die casting (nominal composition: 60 Cu, 37.75 Zn, 1.00 Sn, 1.00 Pb, 0.10 Al, 0.15 Si) furnished by C. S. Smith was also examined. The surface showed a random orientation of alpha and beta. SUMMARY A zinc casting solidified against a molten lead surface was found to have the same surface orientation texture, (001) parallel to the surface, as other zinc and cadmium castings. Aluminum and alpha-beta brass die castings were found to have random grain orientation textures at the surface. ACKNOWLEDGMENT The X-ray determinations were conduced by M. L. Fuller.

Jan 1, 1945

By R. S. McCaffery, D. E. Krause

There has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this tuyere, the arlicle states, resulted in a decrease of blast pressure of about 4 Ib. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 Ib. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-As the die-casting process is so very different in character from the process of making sand molds, it is often considered that entirely different methods of pouring, gating, venting, etc. should be used. There is really, however, no essential difference in the making of (lie castings and sand castings, and similar methods should be used in each process. In the matter of gating, the metal should be introduced at a central point, as nearly as possible, so that it will have an equal distance to flow from the point of entrance to the most distant points of the mold. This will cause a uniform rate of congealing of the casting and prevent streaks and cold shuts. The venting should be done in such a way that a free exit of the air in the molds can occur. It should be less difficult to take care of the venting of a die-casting mold than to vent an ordinary sand mold. In the case of a sand mold, the venting is left, to a considerable extent, to the judgment of the molder, and it is possible that no two molds will be vented in a similar manner. Further than this, after a vent has been made in a sand mold, it may become clogged by the sand and for this reason be inefficient. There is also quite a variation in the pressure of the metal entering a sand mold, due to varying heights of the pouring gate. In a die-casting mold these factors can be controlled more closely. The vents should be so disposed that the air in the mold compressed by the entrance of the metal may be able to leave the mold at a uniform rate and by exits located symmetrically. These exits are made quite small on molds at first, as they can he easily enlarged if necessary, and they are tapered so that a free flow is guaranteed without danger of the metal spurting out from the die. Uniformity of pressure of the metal as it enters the mold is very important and, as the pressure is mechanically applied, its control is not difficult. It is true that a sand mold has much less of a chilling effect on the metal poured into it than has the die-casting mold, but, outside of this point, there is a great similarity between the die-casting process and the process of making castings in sand folds. It is suggested that much would be gained by regarding these two processes as not essentially different.

Jan 4, 1919

By Fred Wise, C. W. Wark

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. MILLING PRACTICE Crushing (Fig. 1).-There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. 1 shows the method and

Jan 1, 1940

By R. P. Olsen, A. K. Schellinger

Molten silicate salts, the important industrial byproducts termed "slags," are known to be electrolytic conductors at furnace temperatures. This property is due to their partial dissociation into ions with the ion kind and size being closely related to the slag composition. Ionic conductance, in liquids, is a function of the viscosity, which in turn is a function of the temperature. It could be anticipated, therefore, that a semi-log plot of conductivity vs. reciprocal absolute temperature might yield a straight line, in the case of molten silicates and salts. As liquids, the viscosity of these slags should follow the Shepard1 relationship: log viscosity = A/T + B Then, if the resistance of the molten slag is directly proportional to the viscosity: log Rs = A/T + B Resistance measurements of molten halide salts,2 and silicate salts34 by various investigators have, indeed, shown this straight line relationship between resistance and temperature. A further relationship between the conductivity versus the degree of ioni-zation, the size of the ions, and the slag composition is, also, to be expected. Large ions, and fewer ions, would move more slowly in a potential field and could not carry as much current as smaller, more numerous, and mobile, ions. Conductivity, therefore, would be smaller in the presence of such large ions and higher slag viscosities. The conductivity-composition relationship is of considerable interest in the case of the industrial slags produced in iron blast furnaces, and non-ferrous smelting furnaces. These slags usually approximate three component systems with several minor components as impurities. At least one of the major components is commonly purchased for the sole purpose of rendering the slag less viscous at a reasonable furnace temperature. Should the conductivity be related rather directly to the concentration of such a purchased slag component (that is, CaO) instrumental measurement and control at the furnace might be possible. Modern tele-metric control methods in aqueous chemical process industries are often based on the property of conductivity of solutions, and its variation with composition. Investigators3 of the phenomenon of electrical conductivity in molten blast furnace slags have established that these systems show lines of equal conductivity on their ternary diagrams at one temperature level. These isocon-ductivity lines form closed contours on the diagrams, and at times, minimum areas occur at which these contours are essentially closed down to a point. The conductivity reading at such a point, at one temperature , would, of course, locate one on the diagram, and give the slag composition. Research in this field is understandably scanty. The reactive nature of

Jan 1, 1950

By Andrew Allen

WHEN a mine is changed from hand, to me-chanical loading, the character of the coal dumped at the tipple is changed in many ways. Selective mining is not so easy with mechanical load-ers, and where much picking is done at the face it is apt to be wasteful anyway. Much recoverable coal is apt to be lost by too free gobbing and, in my opinion, picking at the face should be confined to removal of heavy rock, such as pieces of roof or bottom or sulfur balls. and to such clearly defined and persistent bands as can be readily recognized and segregated. With mechanical loaders of the shovel type, even this amount of gobbing is almost impossible. When coal is shoveled into a conveyor there should be no difficulty in doing as much picking as now by hand loading. The size of lumps may be greatly increased, on ac-count of the ease of handling them with a shovel, as the miners will not break them up in order to lift them into cars. Fines may be increased. This is, of course, not universally true, yet it is my opinion that a shovel breaks the coal more, as a rule, than hand loading. This might not be true with all types of shovels and is cer-tainly not true with a conveyor, either with or without the "duck-bill." The average car load will be greatly reduced in fields such as Illinois and Indiana, in which it is the practice to build up the coal above the sides. Where "level full" regulations prevail there should be no material change. When the coal comes to the tipple these differences usually result in the discovery, that many changes are necessary in the preparation plant. The increase in the percentage of fine sizes will probably not bother the screen, but may overload the conveying apparatus. The larger size lump may clog the chute, but as a rule the efficiency of the sizing screens is not greatly affected. In one completely mechanized mine the proportions of 6-in. lump and 2-in. screenings, when loading by hand, were 16.9 and 51.3 per cent respectively. When loading mechanically, these proportions changed to 15 per cent lump and 53.5 per cent screenings. The picking force on the tipple has been increased from 14 on hand loading to 33 men on mechanically-loaded coal. This is for an output of about 5000 tons.

Jan 4, 1927

JOHN H. NELSON, Worcester, Mass.-At our plant we have done considerable work on notch-bar testing and are farther at sea now than when we started. So far, we have been unable to get the notch-bar test to be consistent with any other known test. Lately, I have been investi-gating the effect of the position of the notch-bar specimen in a, bar. To do this I took a 3, ½ in. square bar and quartered it, then heat treated the four quarters. Each of these pieces was again quartered and a specimen machined and notched. "In this way we would have notch-bar tests from the exterior to the interior of the bar. These were made of such lengths that it was possible to make four impact tests on each speci-men. Extreme care was taken in marking the position of these test speci-mens in the original bar. The notches were then cut with relation to position of the specimen in the original bar. The second notch was cut 90° from the first, and so on around the specimen. In this way, we have found that, with a 3 ½ in. bar of 0.4 or 0.5. per cent. carbon steel when properly heat treated, we could get impact values ranging from 15 to 100 ft.-lb. Just why this is the case we are unable to state; but it does appear to be a fact that along the outside of the original bar the notch-bar test seems to be low and increases toward the center, but it is not always consistent. For instance, we may have, on a single specimen; one notch-bar test giving us 15 ft.-lb. and another 100 ft.-lb. We have not found such inconsistencies in alloy steels. Alloy steel is consistently good or consistently bad. If it. is good, you cannot readily destroy the impact value, no matter what you do; if it is bad-that is, if it is a poor notch-bar steel-and you have sufficient latitude in your draw, you may correct it. In other words, if the hardness you are working to will allow you to draw to about 1050° F.(561° C.) or over and then quench this steel from the draw heat, you. can raise the im-pact value of the steel from about 4 or 10 ft.-lb. up to-40-or 50 ft.-lb: Just what occurs I do not know. There is evidently a critical-point in steels that have poor impact value, in the neighborhood of 1000 F. to 1050° F. (536° to 561° C.).

Jan 12, 1919