Search Documents

By William Kelly

An extensive swamp covers a large part of the town-site of Norway and adjacent laud. Through this swamp run two parallel oreformations. In the north one is the Aragon mine. The south one passes into the swamp on the Harrison property. On the edge of the swamp, about 1000 feet from the Aragon mine, a diamond drill, in the fall of 1889, located the ore-bearing formation and a probable ore-body. To explore further and develop this ore, the Penn Iron Mining Company proposed, in the spring of 1890, to sink a shaft. The drill had shown the depth of the glacial drift to be more than 60 feet. A test-pit near the location of the proposed shaft had struck, at a depth of 20 feet, an amount of water which a 200gallon pump was unable to lower. At the Aragon, a few years before, a shaft had been sunk to hard pan with great difficulty and many delays by the usual method of driving laths. Under the conditions it was decided to sink a caisson- or dropshaft. Two 40-horse-power boilers, a Lidgerwood engine with 4foot drum, and a good derrick were set up; and two No. 10 Kuowles

Jan 1, 1892

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually aver- age about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment.

Jan 9, 1953

By F. R. Hensel

ACCORDING to statements by Guertler,1 Smith and Hamilton were the first to study the copper-titanium alloys, but owing to the presence of large amounts of impurities their data are inconclusive. M. A. Hunter and I. W. Bacon later investigated the electrical conductivity and the temperature coefficients at room temperature. The present writers reported their results2 in November, 1930. Recently Droll published data on copper-titanium alloys3 which agree closely with those obtained by the authors. MATERIAL TESTED The titanium used was in the form of square sintered rods, the analysis of which runs as follows: titanium, 95.4 per cent; silicon, 0.7; iron,1.8; aluminum, 1.4; copper, 0.1; manganese, 0.05. . The ingots were prepared in a high-frequency induction furnace in air atmosphere. Their analyses are given in Table 1. Up to 5 percent titanium the alloys could be forged. Above that amount they were red short and broke up easily. Owing to their rapid absorption of nitrogen and oxygen from the air, the alloys with the higher amounts of titanium tend to form surface films which greatly increase the casting difficulties, especially when small masses of metal are handled. It was, however, possible to prepare sound ingots up to 25 per cent titanium.

Jan 1, 1931

By W. H. Chang

The phase identification results on several Mg-base alloys are presented. These results have been correlated with strength data and microstructural studies to indicate that carbide dispersion may contribute significantly to raising the recrystallization temperature and strength of Mo alloys. Evidence is presented to show that the degree of carbide dispersion, and hence the extent of strengthening, is governed by the "metal/carbon" ratio which, in turn, depends on both the carbon content and the presence of stable -carbide-forming alloying elements. IN recent years, Mo-base alloys containing small additions of C, Ti, and/or Zr have been developed, which exhibit much higher recrystallization temperature and strength than those of unalloyed Mo. The superiority of these alloys undoubtedly results from simultaneous operation of more than one strengthening mechanism. In the present paper, the strengthening effect of carbide dispersion will be discussed. Although the role of carbide dispersion is being increasingly recognized, the nature of the carbides has, to the author's knowledge, not been well es- tablished. In Table I are presented some of the phase identification results on representative Mo alloys. These results have been obtained by X-ray diffraction of residues electrolytically extracted from an ethyl alcohol solution containing 7 pct HC1.

Jan 1, 1961

By P. P. Gregory

NATURAL petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the ``pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the con-trolled methods of production and drilling, a portion of this gas is pro-duced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a-given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grog rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures were increasing.

Jan 1, 1938

By Bennett Bates

NOWHERE in the world has cone classification in closed-circuit grinding with tube mills reached as high a state of development as on the Witwatersrand. In the development of the Far East section the necessity of fine grinding to obtain. satisfactory residues gave rise to a situation with which the cone could cope only at a great sacrifice in efficiency of tube-mill grinding. H., A. White1 recognized the limitation of the cone in his study of the theory of tube milling as early as 1915, but it was not until Ewing, Davis and. Willey2 carried out their tests at Springs Mines during 1920 that the advantages of mechanical classifiers' were demonstrated. During the fall of 1924 the writer supervised a series of tests with Dorr classifiers undertaken by Mr. White, Consulting Metallurgist, at the mill of the Geduld Proprietary Mines, Ltd., Dersley, Transvaal (Far East Rand). The importance of classification to obtain efficient tube-mill grinding was thoroughly demonstrated. The installation of classifiers of the above type that followed the test, confirmed the results of the experimental work.

Jan 2, 1926

By S. A. Ronlov

The importance of recognizing vibration problems during the plant design stage is emphasized in this paper. Often an experienced designer can recommend what type of support to use and how to tune the structure. However, obtaining sufficient information is a serious problem dealing with vibration. Vibration is a well known phenomena which, simply and generally, can be defined as a periodic motion. It is experienced in nature as caused by eerth- quake, wind, or ocean waves, and must be dealt with in the design of structure or ships. It must be realized that wherever there are moving or rotating elements, it is possible that unbalanced forces may induce vibration in the elements themselves, in adjacent parts, or in the supporting structure. Under certain circumstances, vibration will destroy machines or structures quickly and totally. The most widely known case is the total collapse of the Tacoma bridge when subjected to a wind of only 42 mph. Failures due to vibration of machines and/or their supports may occur in industrial plants where heavy equipment employed in the process must be supported and several machines are combined in close proximity. In the Metallurgical and Chemical Div. of The

Jan 1, 1962

By G. R. Purdy, J. G. Parr

The intermetallic compound Ti2Co was studied by X-ray diffraction and metallographic techniques. The phase occurs off stoickzometric composition, with its greatest variance at high temperature. The solubility limits of the phase have been cletermined, and an amendment to the titanium-cobalt phase diagram is suggested. THE first intermetnllic compound to appear at the titanium-rich side of the titanium-cobalt system was found by Laves and wallbauml to be Ti2Co. They described this compound as isomorphous with Ti2Ni and Ti2Fe, and demonstrated that it had a face-centered-cubic structure with 96 atoms per unit cell. This contention is supported by the work of Duwez and Taylor2 and Orrell and Fontana3 who also determined the lattice parameter to be about 11.30A. Rostoker4 believed that Ti2Co did not exist, and that the phase considered by the other workers to be Ti2Co was Ti,Co20. However, Orrell and Fontana determined oxygen and nitrogen contents and found that their alloys did not contain sufficient of these elements to produce significant quantities of a stoichiometric oxygen compound. The present investigation was initiated to determine the composition limits of the phase Ti,Co.

Jan 1, 1961

By Benjamin B. Lawrence

Arthur Launcelot Collins was born at Truro in Cornmall, England, July 8, 1868. His father, J. H. Collins, is well kuown as an engineer, and his books have been widely read in this country: Arthur was the third son. Three of his brothers are engaged, as is his father, in the profession of mining engineering. His education, gained partly at St. Austell, partly at Falmouth, and partly at Nuttall's Collegiate School in Truro, England, was supervised by his father, who was then Lecturer on the Mining Sciences to the Miners' Association of Cornwall and Devon. In 1881, J. H. Collins went to Rio Tinto, in Spain, as chief chemist and metallurgist, and it was there that Arthur began his practical work in the laboratory and continued his studies in chenlistry and mineralogy. To the latter science he was deeply attached; and he never lost an opportunity of adding to his cabinet of minerals, of which he was an ardent collector. In 1883, he became assayer and general assistant to Mr. Nicol, Manager of the Peña del Hierro copper-mines, ncar Rio Tinto. Until 1885 he was associated with his father in the study of the geology of the Rio Tinto belt. In 1885 he retuined

Jan 1, 1904

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort.

Jan 5, 1951

By T. A. Rickard

The lodes of Cripple Creek, Colo., partake of the composition of the geological formation which they traverse. The prevailing rocks are andesitic breccia, lying upon granite, and also bodies of phonolite, trachytic phonolite, nepheline-basalt, etc., penetrating both the granite and the breccia. At Kalgoorlie, in West Australia, the prevailing rock is schistose, and has not been certainly identified, though microscopic sections indicate the probability that it was originally an acid eruptive. The lodes are essentially bands, more highly schistose than the encasing rock, and impregnated to a notable degree with disseminated pyrites and secondary calcite. During 1899 Cripple Creek produced 425,590 tons of ore, having a gross value of $15,658,254; during the same period the output of Kalgoorlie was 467,048 tons, valued at $17,724,587. In chemical composition, the ores at Cripple Creek and Kalgoorlie, respectively, present differences equally interesting to the petrographer and the metallurgist. In both cases we have to deal with altered eruptives as the matrix of the ore; but the much older rock of Kalgoorlie has undergone more decompo-

Jan 1, 1901

By W. E. Horst

During the past few years of operation at Kings Mountain, N. C., full-scale flotation has generally yielded poorer metallurgical results than those obtained in the laboratory or pilot plant. After 2 min in each size of Denver flotation machine in the spodumene rougher circuit, pilot recovery (41.7 pct) was almost three times that of the plant (13.6 pet) and about twice that of the laboratory (21.0 pet). Pilot and commercial plant data are based on continuous operation, and laboratory results on batch testing of rougher performance. The ore is a pegmatite containing spodumene, feldspar, quartz, mica, and amphibolite. Data were accumulated to evaluate the scale-up relationships between laboratory, pilot plant, and plant flotation cells. Flotation rate constants and dimensional analysis were used to define the relationship existing between flotation behavior and scale of operation.

Jan 11, 1958

By Walter R. Hibbard

BACKOFEN' reported recently that "the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [lll.] and [loo] directions aligned parallel to the wire axis." In the introduction, he indicated that this was in contrast to the work of Hibbard,' who reported a single [111] texture after a reduction of 96.4 pct. Unfortunately Backofen stated that this was a reduction in area when actually it was a reduction in diameter, as is clearly stated in the reference. Moreover, the results of Backofen are in complete agreement with the results of Hibbard. Backofen's 97.3 pct reduction in area is an 83.3 pct reduction in diameter, after which he foundadouble [ll11 and[l001texture with the former predominating. Similarly, Hibbard; after an 86 pct reduction in diameter found a double [Ill] and [I001 texture with the former predom- inating. Hibbard, however, when he drew the wire further to 96.4 pct reduction in diameter, found primarily a single [Ill1 texture as illustrated by Fig. 2 of ref. 3. Here also, Hibbard- reported evidences of the [loo] recrystallization texture found by Backofen. It might also be pointed out that Backofen not only drew his wire 97.3 pct reduction in area but also etched them over 99 pct reduction in area from 0.125 to 0.01 in. diam. Hibbard's wires were drawn directly to size. In summary, the deformation texture of cold-drawn copper wire still may be described as primarily a single Clll] texture after a sufficient amount of drawing, such as 96.4 pct reduction in diameter." a

Jan 1, 1952

By W. H. Holman, J. B. Wagstaff

IN spite of considerable interest among blast furnace operators on the question of the penetration of air into the furnace, there is still uncertainty as to how far the blast does, in fact, penetrate. Moreover, it is not always clear just what is meant by the word penetration in this sense. In 1952, Elliott et al.1 showed that at the end of each tuyere of a blast furnace there is more or less of a void. In this region, coke particles are blown around by the force of the air. This explained the well-known observation reported by Sweetser2 hat if a bar is pushed into a furnace through a tuyere it will go easily into the furnace a distance of some

Jan 1, 1958

By Joseph Pogue

THE, prices of crude petroleum and its derivatives have shown an upward trend from 1915 to 1920, and a downward trend from 1920 to 1923, see Table 1. Over the former period, oil prices were dominated by the rapidly increasing demands and inflation incident to the war and its aftermath, while over the latter period oil prices were influenced at the outset by deflation and then by the conditions of overproduction that have characterized the past three years. The purpose of this paper is to analyze the broader features of the more recent price movements in the petroleum industry and to relate these features to basic economic conditions in the industry. INDEX NUMBERS OF OIL PRICES The analysis and comparison of price movements may be facilitated by converting actual prices into relative prices, or index numbers, with 1913 taken as a base of 100. In this way, the various price groups are expressed as percentages of the 1913 prices and may thus be readily compared with one another or with the average prices of other commodities similarly expressed. Table 1 gives the index numbers representing the average prices of crude petroleum, gasoline, kerosene, fuel oil, lubricating oils, and all commodities. The last named is the index of all commodities as published by the U. S. Bureau of Labor Statistics and .is widely accepted .as the official measure of the general price level. The index numbers of oil prices were calculated by the writer from weekly quotations published in trade journals.

Jan 3, 1924

By Charles E. Wait

In the analysis of a set of interesting furnace-products belonging to the metallurgical cabinet of the School of Mines, I placed in the hands of one of my students a sample of litharge which gave the results quoted below. The collection of specimens from which this was taken, represents the products obtained in the blast-furnace treatment of argentiferous lead ores, also samples from the zinc process, and those from the cupellation of the enriched lead. The sample, when received, was marked "bismuth litharge," and was that obtained during the last stages of cupellation. It gave upon analysis the following : Per cent. Lead,.......85.36 Antimony,.......06 Bismuth ,........20 Copper,.....49 Iron,...... 69 Zinc,......18 Nickel,.....01 Silver,....2.94 Lime,.....36 Magnesia,....03 Silica,.....12 Sulphuric anhydride,. .32 Carbonic anhydride,. 1.25 Water,.....24 Oxygen,..,.7.80 99.95 At present I wish merely to call attention to the large percetage of silver present (equal to 857 ounces Troy per ton of 2000 pounds avoirdupois), and also to note two or three determinations that I have recently made, with a view to ascertain, if possible, the condition in which this silver exists. If I mistake not, it is usually assumed that silver exists in litharge in the metallic state; and it is, indeed, in the analyses of litharge, rarely expressed otherwise. This method of reporting the silver is, no doubt, due to the accepted statements that the oxides of silver are reduced to the metallic state at a temperature of 300' C. or less. The following experiments lead me to believe that silver exists in litharge, not entirely in the metallic state :

Jan 1, 1887

By Peter J. Conroy, Julianne H. Gyarmaty

INTRODUCTION The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. The contract includes monitoring of two adjacent longwall panels. This paper summarizes the surface monitoring work that was performed through February of 1982. Mining of the first of the two panels (3 off 3 north) was completed on February 3, 1982. Results of the surface monitoring through completion of this panel are presented and discussed. SITE DESCRIPTION The mine being studied is located in eastern Ohio. The site is west of the Ohio River, approximately 56 km (35 miles) south of Wheeling, West Virginia. The topography of the unglaciated region

Jan 1, 1982

Wabush Mines is the largest single supplier of iron ore to the Canadian steel industry, with 42% of its 6 million tpy of iron ore production going to the company's two Canadian owners-The Steel Co. of Canada and Dominion Foundries and Steel Ltd. Six other companies hold interests in Wabush Iron Co. Ltd. These are Lykes-Youngstown, Inland Steel Co., Intrerlake Steel Corp., Wheeling-Pittsburgh Steel Co., Finsider of Italy and Pickands Mather & Co. Field work on Wabush began in mid-1957 when a long-range program of economic, geologic, and metallurgical investigations started. This work was followed in 1959 by the construction of a temporary camp and a 700-tpd pilot plant. At the same time, work was also started on a 38-mi railway connection to Ross Bay, Newfoundland.

Jan 1, 1970

By H. M. Chance M

The following tables have been compiled from the annual reports of the Inspectors of Mines, to determine the percentages of fatal and non-fatal casualties from roof-falls and explosions of fire-damp. As we cannot assume that every accident has teen recorded by the inspectors ; as many casualties terminating fatally after the lapse of a considerable period, are inevitably recorded as " non-fatal;" and as clerical errors may have crept into the compilation,* the figures of these tables cannot be considered absolutely correct, but the summary is sufficiently reliable to show the features I wish to differentiate. Under the heading " Miscellaneous" are included all accidents not directly attributable to explosions of fire-damp, roof-falls or fails of coal. Prominent among the numerous causes included under this head are premature or delayed explosion of blasts, accidental explosion of powder or cartridges, accidents from mine cam, falls in shafts, machine accidents, sliding of loose coal in pitching breasts, suffoca tion by choke-damp, etc., comprising in all 48 per cent. of the total number of casualties.

Jan 1, 1882

By Leon Keller, William R. Van Slyke, James Stukel

Two 4-ft wide DSM screens were installed during 1957 in one unit of the two-unit heavy media cy- clone section of the Holman-Cliffs concentrator at Taconite, Minn., following successful laboratory test work on a 1-ft screen. The two screens materially reduced the amount of media sent to the magnetic separator cleaning circuit. Wear life was good and fine size capacity was high. Briefly, the Holman-Cliffs heavy media cyclone plant uses -65 mesh magnetite as media and 10-in. diam., 30º Ni-Hard cyclones as separatory vessels. Feed to the plant averages 130 long tons per hr of -1/8 in. +65 mesh material. The conventional heavy media circuit uses drum or spiral type separatory units and treats +l/8 or 3/16-in. material. The medium is generally -65 mesh ferrosilicon. Ore and media are readily separated by screening at about 6 mesh. At this size, capacity is high and wear and maintenance are not excessive. The heavy media cyclone plant requires an efficient separation between +65 mesh ore and -65 mesh media. To reduce costs, however, the separation was made at a coarser size with the result that the media was un- duly contaminated and it was necessary to clean large tonnages of media and ore in magnetic separators. Due to the high capital cost of these units, their number was kept to a minimum and, consequently, they were overloaded. As a result, the separation between magnetic media and nonmagnetics was not sharp and the magnetite losses were high.

Jan 10, 1958