Search Documents

By R. J. P. Lyon

It is usually assumed1,2 that ore deposition is relatively slow, taking place over tens of thousands of years. Yet many syntheses and phase changes can be completed in the laboratory in a matter of hours, under essentially the same pressure and temperature conditions to be expected in nature. Much has been written about geothermometry, and Ingerson's recent summary2 can hardly be surpassed. Rather than review the whole field, this article will deal specifically with diffusion rates in solid solutions* of the sulfide minerals.

Jan 11, 1959

By Weldon B. Smith

When faced with excavating vast amounts of overburden at its surface coal mining operation in Centralia, Wash., the Washington Irrigation and Development Co. (Widco) chose to utilize a bucket wheel excavator and shiftable conveyor system. In the early 1970s, Widco-a subsidiary of the Washington Water Power Co.-held reserves of sub-bituminous C coal estimated at some 180 million tons (200 million st). Subsequent investigation of the overlying land formations revealed the need to excavate millions of bank cubic yards of material as part of the mining plans.

Jan 7, 1979

By Gerald Schroeder

The flow of gases, particularly radon and methane, into the mine atmosphere is a problem traditionally controlled by ventilation-dilution techniques. More recently, a preventative approach has been to seal underground surfaces with a polymeric coating to act as a barrier against the influx of dangerous gases. H However, a study by the Israel Government Research Station indicates that unless the rock surface is perfectly sealed, much of the labor to reduce interstitial gas flow is lost to the effects of barometric "breathing" from the rock pores. Previous research has reported the increased frequency of coal mine explosions during periods of barometric pressure minima,1 and the phenomena has been explained through correlation of the observed increase in mine gas concentrations during periods of low barometric pressure with the connective flow of interstitial gases from rock pores into the arsine atmosphere when pressure was actually falling.234 While changes ill barometric pressure arc rapidly transmitted to the mine atmosphere, response in the rock interstices is sluggish, momentarily creating a pressure differential between the mine atmosphere and the interstitial gases. Responding to the pressure gradient, this interstitial gas flows until pressures are equalized.

Jan 6, 1977

By S. Tiwary, S. Samanta, B. N. Pandey, N. C. Saxena, R. Sinha, B. P. Nandy, B. Singh

Subsidence investigations over one bord and pillar and one longwall caved panel at Dhemomain colliery showed that, although the width-depth ratio (0.82 and 0.83) and working and strata conditions were almost identical, the maximum subsidence over bord and pillar panel was 46.2 per cent of extraction thickness against only 6.9 per cent over longwall panel. The angle of draw was 13O to 210 and 66 to 95 per cent of the subsidence had taken place immediately after extraction. The subsidence profiles were not symmetrical and were of funnel like shape. There was wide variation in subsidence movements over caved faces in India mainly due to difference in the composition of supercumbent strata.

Jan 1, 1983

By T. Sterry Hunt

SINCE: the date of my previous paper on this subject, presented at the Cincinnati Meeting, February, 1881, and published in our Transactions, vol. xii., p. 459, I have had occasion to revisit the Canadian apatite region, and to collect further data concerning its geognosy, which I hope to describe at a future time. At present, I shall put on record a few brief observations concerning the more recent operations in apatite-mining in the Lievre district, to the north of the Ottawa River, where the mines are as yet confined to a small area in the townships of Buckingham, Portland, Templeton, and Darry; the earlier workings having been along the Rideau Canal, to the south of the Ottawa. The large mining operations lately undertaken in the Lièvre district show that the crystalline phosphate of lime or apatite belongs to lodes of great size, which traverse the ancient gneiss of the region. These lodes include a granitoid feldspathic rock, and a pyroxene rock, with large masses of quartz, of carbonate of lime, of pyrites, and of apatite. All of these often show a banded structure, riot unlike that of the gneiss, to which they- are evidently posterior, arid of which they

Jan 1, 1886

By Willard Ide Pierce

The Department (formerly called State) of Tolima, which is beginning to attract considerable attention in this country on account of its mineral wealth, comprises an area of 18,415 square miles, lying between latitude 1" 34' 25" and 5" 44' 12/" N. and between longitude 74" 25' 45" and 76" 34, 25" W. from Greenwich. It is bounded on the north by the Department of Antioquia, on the east by the Departments of Cundinnmarca and Cauca, and on the south and west by the Department of Cauca. It is the most recently created of the States of Colombia, having been established by decree of April 12th, 1861, and being composed of the old provinces of Mariquita and Neiva, and of the districts Melgar, Carmen, Cunday and Santa Rosa, of Tequendama.

Jan 1, 1888

We wish to congratulate the authors on a fine presentation of a difficult and interesting problem. We fully support the findings that liquid or even mushy center reduction has no place in the production of quality steels. We also agree with the findings, or implications, that internal bar quality is not made in the rolling stands, but in the caster. This is the main reason why Inland caster exclusively uses the submerged casting technique after a few months of familiarization with open casting. The metallurgical advantages of combining in-line reduction with a caster are actually indirect. The use of submerged casting and refining powder permits casting of fine grained aluminum killed steels without resorting to expensive grain refiners and cuts down or eliminates reoxidation during casting. Immersion of a snorkel into a small mold may lead to several operating difficulties. Hence, the presence of in-line reduction enables the section to be cast into a large mold, at high output rates, while obtaining some product size flexibility. The capital and operating costs of a caster-- in-line mill are lower than those of the traditional installation with a separate reheating furnace and billet mill. Admittedly, in-line reduction represents an additional challenge to the steelmaker, maintenance man, and metallurgist.

Jan 1, 1972

By R. W. Raymond

GEHEIMER BERGRATH Prof. Dr. HIERONYMUS THEODOR RICHTER, ex-Director of the Freiberg Mining Academy and Honorary Member of this Institute (to give him the full title, which nobody ever thought of using in his genial and unceremonious presence, and the whole of which I have omitted at the head of this notice, as adding nothing to the virtue and value of the man I knew), died on Sunday, September 25,1898. He was born in 1825 at Dresden, and in 1843, after some practical training in pharmacy, entered the Freiberg Mining Academy, where he devoted himself chiefly to metallurgy and metallurgical chemistry, under the guidance of the celebrated Plattner, whose masterly instruction in those arts, and also, especially, in assaying and the use of the blow-pipe, has been classic authority to the present day. In 1853, Richter was ap-

Jan 1, 1899

By A. T. Yu

From the very beginning when an ore body is blocked out, till the last ton of mineable ore is shipped to the smelter, consciously or not, a mining engineer is incessantly wrestling with the materials- handling problem. In the mine and the plants, over the haulage routes, and at the shipping terminals, his fundamental responsibility is to see that each ton of ore and/or waste is extracted, processed and moved easily and economically. Success or failure of many a mining enterprise often rests principally with the judicious and effective application of existant materials-handling technique or its innovation. Time and again, key innovations in practicing techniques have turned a losing venture into a successful and profitable one.

Jan 6, 1967

By D. R. Mitchell

Accent is on mechanization, more preparation plants - Competition from other fuels remains biggest problem.

Jan 2, 1953

By L. D. Jaffe

IT is now well established that quenched and tempered titanium alloys have much better ductility when the quenching is from a two phase a-B structure, rather than from an all B structure. The corresponding microstructural differences, however, have not been shown in previous publications. Accordingly, specimens were cut from a % in. rod of commercial RC-130A, containing 7.9 pct Mn and 0.12 pct C, which had been previously hot rolled, heated 1 hr at 1100°F, and air cooled. (The same heat has been studied by others." 7 Samples about 1/4 in. cube were heated in helium 1/2 hr at 1450' or 1700°F, quenched in brine, tempered in helium 1 hr at various temperatures up to 1250°F, and quenched in brine. They were then sectioned and metallo-graphically examined, using an etchant of HF-HNO, in glycerine. As quenched from 1700°F, the microstructure observed was clear /3. (Probably also present was U, as the hardness was 400 Vhn, but w is not yet reliably revealed by any metallographic technique.) When the /3 quenched alloy was tempered at a high temperature, a precipitated as a grain boundary film

Jan 1, 1957

By N. Arbiter, C. C. Harris

Analysis of ball and pulp flow in ball mills indicates that three factors may become critical with increasing mill diameters: ball size, fraction critical speed, and average pulp flow velocities. Ball diameters may need to be decreased and fraction critical speeds increased with ores which show decreased breakage rate coefficients above 1.2 mm (14 mesh). With 5.5-m (18 ft) and larger mills at higher circulating loads, pulp flow velocities may become capacity limiting and also may limit increases in ball mill diameters.

Jan 1, 1985

By R. L. Tobie, H. W. Seaney

Over the years since 1956 when initial experiments were conducted on underground concreting in an attempt to cope with the ground weight and pressure encountered in the development of a large-scale underground block caving system, the use of monolithic concrete linings has grown to include most of the primary development in the mining area. Although the development cost of concrete linings is higher than either timber or steel-supported openings, the repair and maintenance costs are substantially lower, making concrete the most economical means of ground support. Other ad- vantages are also apparent, in that concrete provides superior fireproofing, better ventilation, and a safer, cleaner working place.

Jan 11, 1965

By James W. Clark, William C. Dixon, Kevin L. Wiley, Thomas R. Couzens

This paper is a description of certain geologic aspects of the Inspiration mining operation. It is not a geologic description of the Inspiration deposit nor an exposition of all the geologic work. Involved in the development and exploitation of the deposit. A few specific examples of the application of geology and geostatistics to the mining process are given to illustrate the progress that has been made in making the Inspiration Mine more efficient and cost effective, and a statement of the philosophy of geologic applications is offered.

Jan 1, 1985

By D. W. Duncan, A. Bruynesteyn

An ore containing chalcopyrite was microbiologically leached in 6 ft columns at particle sizes ranging from -2 +1 ½ inches, to -3/8 + 3/16 inches. The rate of leaching increased exponentially as the particle size decreased. The controlling factor was the active leaching volume made up of the particle surface area and the depth of penetration of the bacteria and leach liquor into the particle. This volume became an increasingly larger part of the total volume as the particle size decreased. The sample under test leached poorly at larger particle sizes and it was calculated that under commercial conditions, it would produce at best a pregnant solution containing 100 mg/l (0.2 lb/ ton) of copper per 100 ft of dump height.

Jan 1, 1974

By C. R. Boyd

It would be a quite congenial task to attempt to describe all that extraordinary mineral wealth which is now giving such prominence to the region from the James River to the Tennessee line: adjacent to the great lines of the Shenandoah Valley and the Norfolk and Western railways; but such a task would be impossible within the limits of any ordinary paper. Hence, in advance of the fifth edition of my book and map on the Resources of Southwest Virginia, I must restrict myself to a limited but most interesting subdivision of this remarkable mineral belt.

Jan 1, 1884

By R. Hogg, F. F. Aplan, P. B. Bradley

The mineralogy of the solids contained in the black-water effluent from coal preparation plants has been investigated. Samples were obtained from 13 locations, representing major coal seam in the Appalachian, mid-continent, and western regions of the United States. On the average, the samples were found to contain 60% carbonaceous material with the balance as mineral matter. The mineral fractions from all of the samples from the eastern half of the United States were found to be remarkably similar, consisting of over 50% illitic clays; about 10-15% each of kaolinite, calcite, and quartz; and lesser amounts of chlorite and pyrite. The western samples were somewhat different, generally containing significant quantities of montmorillonite clay. Flotation may be wed to recover additional clean coal contained in the black-water discharge.

Jan 1, 1981

By William G. Fricke

MaCROSEGREGATION, as distinct from microseg-regation, is often inverse in nature. That is, the eu-tectic solute elements, which are expected to be con-

Jan 1, 1970

By Randy M. Cole, Peter J. Phillips

A methodology is presented which quantifies six coal utilization cost components, each proportional to a coal's mineral content. These are: Ash disposal costs, coal transportation costs, plant maintenance costs, reduction in plant peaking capacity, reduction in plant rated capacity, and reduction in plant availability. Numerical examples illustrate that coal containing between. 12.5% and 25.0% ash-plus-sulfur can cause incremental utilization costs ranging from less than $1.00 to more than $8.00 per ton of coal, when combusted in a pulverized coal fired power plant. Estimated costs are then compared to historical data and the conclusion drawn that steam coal beneficiation may have broader economic justification than sometimes realized. It is noted that TVA, which first proposed the methodology and parameters used here, is continuing research on this aspect of coal utilization.

Jan 1, 1981

By Joseph Pogue

THE prices of crude petroleum and its derivatives have shown an upward trend from 1915 to 1920, and a downward trend from 1920 to 1923, see Table 1. Over the former period, oil prices were dominated by the rapidly increasing demands and inflation incident to the war and its aftermath, while over the latter period oil prices were influenced at the outset by deflation and then by the conditions of overproduction that have characterized the past three years. The purpose of this paper is to analyze the broader features of the more recent price movements in the petroleum industry and to relate these features to basic economic conditions in the industry.

Jan 3, 1924