Search Documents

By D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill.

Jan 8, 1951

By J. R. Spencer

When supplies of high pressure mercury or other liquids are required in analytical work, it is convenient to have the source of supply at a relatively constant pressure and available in sufficient volume to satisfy the requirements of the apparatus in use. It is also desirable that the pressuring device be as simple and as inexpensive as possible and convenient to operate. This pump combined with a small storage reservoir containing gas under pressure has the attributes of (1) positive control of the maximum output pressure through the use of a regulator in the low pressure air supply; (2) an increasing capacity as the rate of withdrawal of mercury from the pressured system is increased; and (3) simplicity, requiring only the use of a lathe, drill press, and welding unit in its construction. DESCRIPTION Essential parts of the pump are shown in Fig. 1. In appearance the unlt is similar to the usual steam pump in common use in industrial applications although considerably smaller in size. The main differences lie in the area ratio of the air and mercury pistons and in the design of the air valve mechanism. Approximate diameters of these pistons are 4.25 in. to 0.375 in. respectively, giving an area ratio of about 130 to 1. The air piston (2) is attached to the end of shaft (4), with the mercury piston being merely a reduced extension of the shaft. Mercury intake and discharge to the pump are controlled by high pressure check valves that screw into the ports indicated at (6). Air supply is controlled by the valve assembly mounted on top of the

Jan 1, 1950

By W. R. Hibbard Jr., T. Michalak

THAT the amount of deformation and annealing time influences the recrystallization temperature of cold-rolled copper has been well established. Evidence that the recrystallization temperature can be affected by the deformation texture has been reported by Brick and Williamson,% ho found that copper straight-cold-rolled to 99 pct reduction to produce one deformation texture and copper cross-cold-rolled to 99 pct reduction to produce a second and different deformation texture correspondingly recrystallized at different temperatures to different textures. The purpose of the present work was to study more thoroughly the effect of the deformation texture on the recrystallization of cold-rolled copper. Experimental Procedure The copper used in this investigation was commercial OFHC copper (nominally 99.985 pct Cu) in the form of 0.500-in. plate. Qualitative spectro-graphic analysis showed only a slight trace of iron and a trace of silver. No analysis was performed to determine the exact content of the iron and silver,

Jan 1, 1958

By J. M. Duke, A. J. Naldrett

Significant resources grading less than about 1% nickel occur in magmatic sulfide deposits of two types. In the Mt. Keith type, extensive zones of disseminated nickel sulfides occur in the central portions of certain synvolcanic dunite-peridotite sills of komatiitic affinity in Archean greenstone terranes. In the Duluth type, disseminated copper-nickel sulfides occur near the basal margins of intrusions of flood basaltic affinity associated with intracontinental rifring. In both types, the parent magmas became saturated with sulfide following the onset of fractional crystallization and the separation of the immiscible sulfide melt was accompanied by the precipitation of a relatively large proportion of silicates. The abundant silicate crystals impeded the coalescense and accumulation of the sulfide droplets with the resulting formation of large but low grade deposits.

Jan 1, 1983

By Carroll Wegemann

THAT Colorado was producing oil and gas before the fields of the Mid-Continent were discovered is a fact too frequently overlooked. As early as 1862, oil was obtained in the Florence district (see Fig. 1) from seepages and shallow holes. The first well that could be regarded Fig. 1. as being truly commercial was drilled in this field in 1876. The field is now producing 100,000 bbl. per year, and is credited with a total production of approximately 11,000,000 bbl. The small field near Boulder, Boulder County, was opened in 1901; production has now practically ceased but the field is credited" with a total production of 610,000 bbl. Oil was discovered at Rangeley in 1901, and the field supports a small local refinery at the present time. The first shallow well in the White River gas field was drilled in 1892, and the wells now producing have been

Jan 3, 1925

By J. D. Verhoeven

In a recent study1 this author has investigated the effect of an electric field upon the solute redistribution accompanying solidification of Sn-Bi alloys. It was concluded that the primary effect of the electric current upon the solute redistribution resulted from electrotransport within the liquid boundary layer at the solid-liquid interface. In order to maximize the electrotransport effect all of the experiments were conducted at the highest current densities experimentally attainable. It was found that these high current densities produced considerable convective mixing within the liquid metal. This mixing reduces the boundary layer thickness and consequently reduces the effectiveness of the electric field in producing solute redistribution. Consequently, it is quite possible that the condition of maximum achievable current density would not correspond to maximum solute redistribution. It may be that, as the field intensity is increased, a point is reached where the additional solute redistribution from the increased electrotransport is more than offset by the decrease in solute redistribution resulting from the increased mixing in the liquid. In order to check this possibility the effective distribution coefficient has been determined as a function of current density in a series of experiments. The experiments were conducted on 6.6 at. pct Bi

Jan 1, 1968

By D. H. Fleming

DURING 1950 the jet-piercing process was used commercially in the piercing of primary blast- holes in magnetic taconite at the preliminary taconite plant of the Erie Mining Co., Aurora, Minn. The Erie Mining Co. purchased a jet-piercing ma- chine and associated equipment in 1949, and the machine has been in operation since its installation in the summer of that year. An overall view of the pit with the JPM-1 jet-piercing machine in operation is shown in Fig. 1.

Jan 7, 1951

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost,1 are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger2 was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil3 have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo- physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electro- chemical circles since 1910.4

Jan 3, 1957

By George I. Smith

Jan 1, 1985

By R. W. Raymond

Samson Jordan was born at Geneva, Switzerland, June 23, 1831. At the age of 20 years he entered the Ecole Centrale des Arts et Manufactures, at Paris, from which he was graduated with high honors in 1854. After some months of service with the Compagnie du Chemin de Fer du Nord, he was employed (upon the recommendation of his former instructor, Prof. Burat, who had recognized his remarkable ability) at the mines of Portes, belonging to the Société de l'Elairage au Gaz et des Hauts Fourneaux, etc., of Marseilles, and subsequently to construct the St. Louis iron blast-furnaces of that Co. After finishing this work, he remained at Marseilles as a member of the directory of the Co., particularly connected with the development of its mines. In 1862 he became the general advisory engineer of the Co., and still later (1873) its general manager (Administratet~r), a position which he retained until his death, February 24, 1900. He became subsequently Administrateur of other important French industrial enterprises, including those of the Compagnie des Naut Fourneaux, Forges et Aciéries de Denain et Anzin, and the Compagnie Banco-Belge des Mines de Somorrostro ; and he was also, at various times, President of the Société technique du Gaz, Vice-President of the Comité des Forges de France, mepber of the Council of the Société d'Encouragement pour l'Industrie nationale. In all these positions, it is the unanimous testimony of his colleagues that he was no mere ornamental figurehead, but a profoundly wise, practical and industrious laborer and adviser, both patient and keen in the mastery of details, yet at the same time competent to apprehend the wider bear-

Jan 1, 1902

By Peter Joralemon

Peter Joralemon's contention that Nevada contains one of the world's major gold belts is the result of 30 years' active involvement with the state's regional geology. He first suggested the possibility of an arsenical gold belt-tenuously based on two replacement deposits 480 km (300 miles) apart-in his 1949 doctoral thesis of the Getchell mine. In the years that followed, some 18 or 20 arsenical gold ore bodies have been discovered along the lineament Joralemon postulated. In this article, he uses the evidence that he's collected over the last three decades to refine his 1949 thesis. Joralemon's conclusion: A mineral belt containing a billion dollars worth of gold extends the length of Nevada, and a number of ore bodies are yet to be discovered.

Jan 7, 1978

By John Chipman, Daniel Dutilloy

The equilibrium of gaseolis H2O-H2 mixtures with liquid iron-phosphorus alloys in the range 0 to 3 pct P is used to establish the increuse of the activity coefficient of oxygen, in the presence of phosphorus. Two different sampling techniques are used. THE importance of oxygen as a refining agent in steelmaking operations makes it desirable to improve our understanding of its behavior. Phosphorus which is always present in the ores has adverse effects on steel properties and its removal is necessary. The present study was undertaken to evaluate the interaction of oxygen and phosphorus in molten iron. Bookey, Richardson, and welch1 have studied the phosphorus-oxygen equilibria in liquid iron in the presence of lime. They used a mixture of hydrogen and water vapor to control the oxygen potential and worked with crucibles made of tetracalcium phosphate and lime. At low phosphorus concentration, i.e., at high oxygen, they observed a marked deviation in their results. They tentatively ascribed this to a large negative effect of oxygen on the activity of phosphorus. This was then included by chipman2 in his review of interactions in liquid iron. Pearson and Turkdogan 3 have later reported an interaction parameter They equilibrated a mixture of hydrogen and water vapor with an iron-phosphorus alloy contained in an alumina crucible and sampled the melt by suction in a silica tube. The solubility of oxygen in iron-phosphorus alloys has been studied by Levenets and Samarin.4 They reported an interaction parameter

Jan 1, 1961

By D. Malhotra, R. M. Hoover

The effect of a surfactant, designated Syntex, on the wetting and spreading of hydrocarbon oil on molybdenite surfaces (faces) has been investigated experimentally through measurements of zeta potentials and factorially designed flotation tests. These studies indicate that Syntex has a positive effect in increasing molybdenite recovery in the rougher flotation circuit at the Climax mill. The analysis of experimental data using DLVO theory shows that the controlling factor in determining the magnitude of the repulsive energy barrier preventing oil from wetting and spreading on the molybdenite faces is the MoS2 zeta potential and the vapor oil droplet size. The role of Syntex in this case seems to be related to the decrease and stabilization of MoS2 zeta potential by Syntex adsorption and also to the emulsifying action of Syntex on vapor oil to provide a more favorable oil particle size.

Jan 1, 1976

By L. G. Austin, P. T. Luckie, R. R. Klimpel

Application of the Charles and Bond Laws to batch grinding can be deduced as a special case of solution of the first-order batch grinding equation. With additional limitations on the feed size distribution, this special case also gives Rosin-Rammler distributions of constant slope, with the 36.79% retained point a simple function of time. In general, the assumptions concerning the breakage parameters S and B which are necessary to get Charles' and Bond's laws, are not valid except as a crude approximation. With less restrictive assumptions, it is still possible to get approximate Rosin-Rammler distributions, but the slopes change with time of grinding, and the 36.79% retained point is a more complicated function of time. An alternative form to Charles' law is suggested, which accomplishes the same result and has the same errors, but avoids the use of energy of grinding and deals with specific rate of grinding.

Jan 1, 1973

By Richard B. Greenwalt, John M. Bertram, George E. Aiken

Agglomeration developments in the iron ore industry of North America over the past twenty years are closely related to shifting patterns in commercially acceptable ore grades and even the definition of iron ores. As early as WW II the rich Mesabi hematites were depleted, ending a 50-year era of direct shipping ores that included reserves of an estimated three billion tons. Decreasing ore grades and rising costs began to force the closing of many underground iron mines and processes were being developed to use domestic low-grade iron deposits. This resulted in the rapid development of iron ore beneficiation processes and signaled the coming trend toward concentration, sintering and pelletizing. Yet even today when agglomeration facilities are treating 90 % of the Mesabi Range product much remains to be done in keeping world-wide competitive forces in check and in ensuring the long- term utilization of these expansive ore supplies in an up-until-now captive U.S. market.

Jan 10, 1973

By C Gunther

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By M. F. Williams, L. G. Hendrickson

In classification of pulps bearing magnetized ferro-magnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in flocs. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used.

Feb 1, 1956

By John J. McKetta, Donald L. Katz

Recent experimental data on the methane-n-butane-water system have been combined with data in literature to present: (I) the water-vapor content of natural gases, (2) the solubility of water in hydrocarbon liquids, and (3) the solubility of natural gases in water. Since water is present in petroleum reservoirs, experimental data regarding the behavior of water in hydrocarbon-water systems is of increasing engineering importance. A survey of literature (Table I) shows that data of these types are fragmen-tary at temperatures above the hydrate region. Experimental data taken from the authors' recent investigation of the meth-ape-n-butane-water system are presented.17

Jan 1, 1947

By W. D. Grundy, Frances Wahl Pierce, Jean-Paul Marbeau, Carol Waite Conner

Resource and coal quality estimates of three coal deposits in the Western United States were estimated by kriging, a geostatistical method that yields unbiased estimates with maximum achievable precision. Derived geostatistical models were used in kriging to estimate the tonnages of the deposits and to derive contour maps of thickness, structure, and sulfur content. Where data were available on quarter-mile spacing, kriging was used to obtain detailed information applicable to mine planning and design. Where data were sparse, kriging was used to do a preliminary evaluation of total resources. Geologic studies were required to correlate the individual coal beds and to identify complicating conditions such as the presence of faults, burnt zones, channels, and regional changes in thickness and elevation. Where these conditions were identified, they were explicitly integrated into the estimation procedure.

Jan 1, 1983

By R. V. Ramani, T. S. Kovach

In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas that have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development, and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

Jan 1, 1985