Search Documents

By Horace C. Knerr

It has been shown that the resistance to corrosion of duralumin sheet is greatly influenced by the quenching medium used in heat treatment, or, more specifically, by the rate of cooling during quenching. The severity of corrosive attack after exposure to salt-water spray increases in .the following order: The tensile strength, yield point and elongation are only slightly affected by the quenching medium, as shown in Table 1. Tensile test requirements: yield stress, 25,000 lb. per sq. in. minimum; ultimate stress, 55,000 lb. per sq. in. minimum; elongation in 2 in., 18 per cent. minimum.

Jan 1, 1931

By H. F. Ameen, F. M. Hamilton

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given.

Jan 12, 1950

By Nick Barton, Stavros Bandis

The descriptive term "rock mass" encompasses individual block dimensions ranging from centimeters to many tens of meters. Strength and deformability vary both qualitatively and quantitatively as a result of this size range. A key issue is therefore the appropriate size of the test sample. A large body of test data was reviewed to determine the influence of block size on the displacement required to mobilize peak strength. It is shown that the shear strength and shear stiffness reduce with increased block size due to reduced effective joint roughness, and due to reduced asperity strength. Both are a function of the delayed mobilization of roughness with increasing block size. A method of scaling shear strength and shear displacement from laboratory to in situ block sizes is suggested. It is based on the assumption that size effects disappear when the natural block size is exceeded. This simplification appears to be justified over a significant range of block sizes, but is invalidated when shearing along individual joints is replaced by rotational or kink-band deformation, as seen in more heavily jointed rock masses. Recent laboratory tests on model block assemblies illustrate some important effects of block size on deformability and Poisson's ratio.

Jan 1, 1982

By R. J. Jones, L. D. Clark, R. C. Howell

This research provides an empirical approach toward further analysist10 of the variables in rock breakage under direct, hydroimpact (impacting on fluid) and explosive impulse loading. That the strain on the face of a block of rock, below an impact pin or explosive charge, is directly proportionate to the rupturing force F and inversely proportionate to the product of the burden W and the hole periphery S, is borne out in the laboratory using electrical resistance strain gages to measure a peak strain during rupture by small explosive charges detonated in boreholes. Furthermore, such findings established the validity of the expression F = Ss • Wy • R as a useful relationship from which, it is believed, can be derived practical applications in commercial rock blast design.

Jan 1, 1972

BROWN iron ore reserves of Franklin county are being proved economical by Heavy-Media separation at the Blackburn mine of the Shook & Fletcher Supply Co. about 120 miles north-west of Birmingham. The ore occurs under a cover of ferruginous chert and gravel and these materials are also disclosed as streaks in the ore body as it is mined. Previous methods of jigging and hand sorting the ore became too expensive because of rising wages but the use of Heavy-Media separation has proved economical and is making Franklin county the most promising source of additional reserves of brown ore.

Jan 12, 1950

By Zay Jeffries

Jan 1, 1930

By Lauren A. Wright

The principal talc deposits in California are in a 200-mile belt paralleling the state's eastern border. The southernmost deposits represent selective alteration of early pre-Cambrian (?) carbonate strata, and are associated with granitic rocks. Deposits in the Death Valley area are at or near contacts between late pre-Cambrian carbonate rocks and diabase sills. Those in the Inyo Range area are chiefly alterations of Paleozoic carbonate rocks and silica rocks. Most of the state's talc output is used in ceramics.

Jan 1, 1950

By A. D. S. Gillies

One of the most difficult places to ventilate in any mine is the working face area. With an everchanging configuration, continual modification and extension to the ventilation system is necessary to maintain an adequate supply of fresh air and to avoid mixing and recirculation in the face area. In coal mines, methane emissions and high dust levels as coal is broken and removed from the face area can produce unhealthy and dangerous conditions if ventilation is not adequately monitored.

Jan 1, 1982

By R. W. Smith, K. H. Lee Discussion by Fred C. Bond

Fred C. Bond (Tucson, Ariz.) — This is a valuable paper presenting much well directed research testing. It describes a practical method by which the long and relatively accurate Bond closed-circuit grindability can be adapted to a known ore so that results of comparable accuracy can be obtained on the same ore from much shorter batch grinding tests. This can be very useful in control work. In large mills a routine batch grinding test on the head sample can be made each day, or even each shift, to check grinding performance by comparison of the work index from each mill grinding section with that obtained from testing. However, it would be well to re-standardize the batch test against a Bond test, perhaps once a week at

Jan 1, 1969

By Jerome S. Nelson, William S. Johnson

Seismic investigations at pre-construction sites commonly are limited to obtaining velocities and thicknesses of subsurface intervals which are useful in estimating construction costs, but are sometimes difficult to apply to project designing. This paper shows through a case history of the San Bernardino Tunnel Intake Tower, a part of the California State Water Project, that dynamic rock properties and dynamic resonant frequencies can be determined and velocity models constructed from in situ field studies and that these are theoretically correct after simplifying assumptions are made. These data can be used to confirm and extend information obtained by conventional methods such as drilling and laboratory static testing.

Jan 1, 1971

Jan 1, 1920

Jan 1, 1922

By B. Etkin, A. A. Haasz

The Infrasizer Mk III, developed at the University of Toronto, is capable of sizing particles of a few pm to hundreds of pm according to particle terminal velocity, which is a function of particle density, size and shape. The factors limiting the performance of the Infrasizer Mk III have been presented and analyzed. It has been established theoretically and experimentally that the device has excellent potential as a laboratory instrument. The principle is applicable to a continuous production classifier, a prototype of which is now under development.

Jan 1, 1980

By Atmesh K. Sinha

In spite of the artificial supports which are provided to reinforce the mine roof and prevent failures, roof falls continue to occur very frequently in the mines due to the very unpredictable geological conditions and the dynamic nature of the mining operations. In fact, roof fall is still one of the largest contributor to coal mine fatalities. The design of a roof support plan is often based on arbitrary criterions due to the unpredictable behaviour of the rocks under the mining conditions. The failure of a mine roof which ultimately results in a roof fall and contribute to mine hazards, is caused following a gradual degradation in its physical conditions. A mine roof monitoring system capable of monitoring the rate of deterioration of a mine roof on a continuous basis has been developed and tested in an operating coal mine. The monitor can help to improve and supplement the roof support plans and

Jan 1, 1983

By H. H. Stoek

Among the mining and metallurgical achievements of the latter part of the nineteenth century, not the least is the incep tion and successful prosecution by mining men of a technical educational movement which in magnitude surpasses any similar movement ever before set on foot. The following account of this undertaking has been prepared at the request of the Secretary of the Institute :*

Jan 1, 1899

By Gary E. Butts, Paul R. Smith

Introduction The design of a mineral processing flowsheet involves many factors. The importance of the sample can not be overemphasized. Competent and thorough mineralogical examinations are important as an aid in designing the test program. Designing and conducting the laboratory test program is basic to the design of the flowsheets. In the project under consideration a flotation pilot plant was conducted to prove the process and to provide a realistic prediction of metallurgical results. Moreover, the pilot plant operation provides important pilot plant design data. Finally, accurate and clear reporting is essential so that the information developed can be utilized advantageously by the client and the engineering firm. The design of a minerals processing flowsheet is a team effort. Engineers from the mining company, the research organization, and the engineering firm all contribute to the effort.

Jan 1, 1978

By Hobart M. Kraner

THE mineralogy of blast furnace sinter is of interest because its mineral content is one of the important factors contributing to its character. There are so many other factors affecting the properties of the sinter, however, that it is well to mention them here. The proportion and character of the raw materials, that is, raw ores, concentrates, returns, and fuel, as well as the mixing and the water content, all have a marked effect on the physical properties of the product and the degree to which sintering action can be carried on. The process of sintering is a relatively fast operation. In as much as appreciable time is required to carry on processes of fusion in such masses of low thermal conductivity, large lumps of hematite ore frequently remain unfused and partly unchanged in state of oxidation in the sintering process. The kind, the grain size, and the amount of fuel used affect both the completeness of the fluxing reaction and the prevailing atmosphere. The rate of reduction in laboratory tests is not only dependent upon the state of oxidation of the sinter but also upon the sizing and porosity.

Jan 11, 1953

By John Dodd

This paper reviews advances in the technology of abrasion resistant iron and steels, which could help combat abrasion and wear in mining operations. With the recent progress in high chromium alloy iron development, high temperature heat treatment of massive castings can be eliminated, aloy cost reduced, and cracking problems avoided. Data on erosion-corrosion resistance of these irons; trends in the development of improved cast steels; and factors influencing toughness and abrasion resistance of manganese steels are all considered. The 7% Mn. 1% Mo manganese steels are shown to combine toughness and abrasion resistance, and composite castings are a means of combating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1982

Jan 1, 1883

By J. Leja, N. Sheikh

The stability of lead ethyl xanthate precipitate in aqueous environment of different pH (4.5 to 10.5) and at temperatures 25°C-60°C was investigated. Dissolution leads to a wide variation of pH, xanthate, and lead ions concentration in solution and to a deposition of solid products of reactions. X-ray diffraction patterns of these solids enabled identification of Pb(OH)3, PbCO3, and PbS as constituents of the remaining undecomposed Pb(EtX)1, together with some unidentified compounds (which give rise to intensive peaks with d values of 2.82A and 1.71A, and numerous peaks of lesser intensity).

Jan 1, 1974