Search Documents

By V. Patarini, M. Salkind

BECAUSE of its high strength and stiffness coupled with low density, continuous boron filament is showing great promise as a potential reinforcement for both metals and nonmetals. Of primary consideration for structural applications is the fatigue behavior of boron fiber composites. Composite fatigue behavior is dependent upon three factors: 1) fiber fatigue behavior, 2) matrix fatigue behavior, and 3) the effect of the interface and fiber ends. The purpose of this note is to describe the behavior of boron filament in rotating beam fatigue. The filament, described by Talley' and Galasso, Salkind, Kuehl, and Patarini,' was made by the hydrogen reduction of boron trichloride on a hot tungsten filament. Testing was performed using a commercial rotating beam wire fatigue tester* described by Votta.~ One end of the test sample is held in a chuck in a synchronous motor. The sample is bent around in a "U" shape, and the other end inserted into a carbide bushing. The maximum strain occurs at the bottom of the "U" where the radius of curvature is a minimum. The strain is adjusted by adjusting the length of the specimen and the location of the bushing. Samples were rotated at 3600 rpm and an automatic shutoff device used to determine the number of cycles to failure. The measurements were accurate to the nearest 360 cycles. The fatigue behavior is summarized in Fig. 1 for fifty-one samples of 4.8 x 10"3 in. diam fibers and ten samples of 3.2 X 10"3 in. diam fiber. The two sample groups represent two different filament production runs and two different nominal size groups. Both groups exhibited nominal tensile strengths of 400,000 psi. No significant difference in the fatigue behavior of the two sample groups is apparent. The scatter in the data is not unexpected for a brittle filament which exhibits a tensile strength distribution with a standard deviation of 10 to 15 pct. Because the test procedure provides a known outer fiber strain in the sample, the maximum stress was calculated assuming a Young's modulus of 58 x 10' psi. This value was selected as being representative of several nominal fiber sizes.2 All of the samples which failed exhibited sudden, catastrophic fracture, and no permanent deformation. One sample was stopped after 1.66 x lo8 cycles at *200,000 psi. The fiber exhibited no apparent damage or deformation. It is apparent that the fatigue resistance of boron filament is quite good. It can therefore be speculated that the fatigue behavior of boron fiber composites would be controlled by the "weaker links", namely matrix fatigue resistance and interface behavior. In fact, preliminary investigations have revealed that this is true for boron-reinforced aluminum? It should be noted that the data presented herein may not necessarily reflect the tensile fatigue behavior of boron filament. It is well-known that boron filament has a radial residual stress pattern with the outer surface in ~om~ression.~ Because of this fact, tensile failure is normally nucleated in the interior of the filament.5 Since the data presented herein is for a rotating beam test in which only the outer surface of the fiber is stressed to the maximum value, it would be incorrect to assume that the failure mechanism and fatigue behavior would be the same if the fiber were tested in tensile fatigue. The fact that many of the data are well above the nominal 400,000 psi tensile strength would tend to support this argument. The authors would like to express their appreciation to the United Aircraft Research Laboratories for supporting this investigation and for permission to publish the results. A portion of this effort was supported by the Air Force Materials Laboratory under contract AF33(615)-2125.

Jan 1, 1968

By R. F. Mitchell, G. F. Dillon, A. F. Armington

In this paper the present methods of boron preparation are discussed with emphasis on the iodide intermediate. Several methods of boron triiodide preparation were investigated, the most satisfactory method being the preparation from the elements. A yield of 60 pct based on iodine is found for this method. Zone-refining, sublinzation, distillation, and fractional-recrystallization results are given for the boron triiodide, with distillation producing the best results. Several methods of decomposition are also discussed. The purity of the resulting iodide boron approximates the puritjl of the best available bromide boron, ELEMENTAL boron has been suggested as a possible high-temperature semiconductor by several workers,' but has never been exploited as a device material. The principal difficulty with boron is the unavailability of pure crystalline material from which accurate information on electrical properties could be obtained. Most boron crystals presently produced are very imperfect in structure and of questionable purity, particularly in relation to carbon content. Several methods of boron purification have been reported in the past few years, all of which produce material with a purity better than 99.0 pct. Most of these methods have been the subject of a recent review by Starks' and will not be elaborated upon in this report. However, of all the purification methods reported, only those using halide intermediates produce a purity approaching that usually required for electronic applications. The bromide intermediate has been most used for the preparation of high-purity boron.'y3 This material is easily prepared from the elements and can be effectively purified by distillation and decomposed by hydrogen reduction. The resulting product contains a trace of silicon, and an uncertain amount of carbon, believed to be approximately 100 ppm. It has been recently reported by Russian workers that high-purity boron can be produced using an iodide intermediate.' In the work cited, boron is reported free of spectro-scopically determined impurities, but the reported detection limits are quite high (- 100 ppm). In addition, no data is given on the carbon content of the product. In the present paper, boron triiodide was chosen as the intermediate for several reasons. First, carbon tetraiodide, which could be a major impurity, is reported to be unstable above 200" and hence could be easily separated from the boron triiodide by its decomposition, since temperatures greater than this are attained during the purification process. The low melting point (45°C) and boiling point (20B°C) and the relatively high vapor pressure of boron triiodide should allow the application of any physical purification technique to the material. The possibility of a lower decomposition temperature than that used for the bromide process is another advantage which might cut down extraneous contamination. The iodide, however, does have certain disadvantages when compared with the bromide, the production cost being the most significant. This is the result of a higher halide-to-boron weight ratio, which means more intermediate must be employed. The cost of the starting material is also greater for the iodide. This cost could be considerably reduced however, by recycling the iodine byproduct. Epitaxial growth of boron, which is probably the best method of producing junctions, should be possible with either the bromide or the iodide as the intermediate. However, this has been attempted only on a limited scale up to the present time because of the unavailability of good crystals. The authors have been relatively successful in laying down a heterotaxy of boron on silicon, however. This will be reported at a later date. Several crystalline modifications have been reported for boron, four of which are now believed to be real.' These are the a! and 0 rhombohedral and the a, and 0 tetragonal. In general, the a! rhombohedral is the low-temperature form and the B rhombohedral is the high-temperature form. The tetragonal structures are detected between 1000"

Jan 1, 1964

By A. G. Guy

In a special type of electrodiffusion experiment the entire specimen is at constant temperature. The vacancies are then created at one end of the specimen and flow to the other end where they are destroyed. The energy required to operate the corresponding sources and sinks results in a super saturation of vacancies at one end of the specimen and an under -saturation at the other end. This gradient in vacancy concentration produces a chemical-diffusion flux, J(D), of vacancies in addition to the flux, J(E), caused by the electric current. Using the experimental data of Ch. Herzig,5 it is shown that a super saturation of 1 pct can cause J(D) to be about 25 pct of J(E), and thus account for the anomalous behavior of short specimens. THERE are advantages in a phenomenological treatment as contrasted to an atomistic one. For example, there are many reactions involving the element copper that are quantitatively and usefully understood from a phenomenological viewpoint, even though electron theory is not yet able to predict whether copper should be fcc or cph.' Similarly, the lack of a complete atomic theory of vacancies need not prevent the development of a treatment based on thermodynamics and chemical kinetics. In the following discussion, models will be used for the vacancies and for the mechanisms by which they move or are created or destroyed, but the phenomenological treatments are not dependent on the details of these models. The important product of a phenomenological analysis is an equation that describes the relation among the measurable quantities determining the behavior of the system. Based on such an equation, experiments can be performed to study these quantities in detail. Eventually atomic theory will supply an adequate theoretical base for the phenomena in question. A chemical species whose chemical potential was invariant during reactions in binary and ternary systems of varying composition would indeed be an anomaly. Yet this is the role that has frequently been assigned to the vacancies in pure metals, in dilute solutions, and even in ordinary alloys. The weight of available evidence supports the view that supersatu-rations of vacancies are on the order of 1 pct in usual diffusion processes.' Although it may seem strange that such a small deviation from equilibrium could significantly affect the thermodynamic properties of the vacancies, it is well known that the driving force for an ordinary chemical reaction is the departure of the components from their equilibrium state. Similarly, the reaction of vacancies that results in the formation of pores in various types of diffusion3 can reasonably be attributed to the supersaturation of vacancies. In the present paper, it will be shown that small degrees of supersaturation can significantly affect the kinetics of the diffusion process itself. ISOTHERMAL ELECTRODIFFUSION Two different experimental techniques are convenient for studying the behavior of vacancies in a pure metal in the presence of an electric field. Gilder and Lazarus4 studied self-electrodiffusion in a gold specimen in which only the central portion was at high temperatures. In this case the significant vacancy sources operate inside the specimen in the presence of a temperature gradient. In the laboratory of Th. Heumann a method has been devised for studying self-electrodiffusion at constant temperature.5 In principle, there is then no effect of thermodiffusion. It will now be shown why in this case the significant ATungsten disks \^^ ^^ ^Gold disks^^ ^^"T>.... "TTZA ? Up Iy'7 markers ///// ////// initial plane p I y/y/y of joining \I 7//// V7//A_________I_________V//// -I 0 +I Distance from center of specimen (a) -— Direction of flow of electrons —Direction of flw of vacancies %yy} Matano I z~irkendall /%W, vy/A inlerfacej "interface ///// -} HfiK- +/ 0 Distance from center of specimen (6) Fig. 1—-Schematic illustration of the essential features of isothermal self-electrodiffusion. (a) Initial condition of specimen. (b) Condition of specimen after electrodiffusion.

Jan 1, 1970

By E. E. Thurlow

The Geology Div. of Northern Pacific Railway Co. has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photo-geologic interpretation. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occa sional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted. Northern Pacific's program of reconnaissance mineral evaluation of company-owned lands and adjoining areas was outlined in a paper presented at the American Mining Congress meeting in Las Vegas four years ago. That report included policies and procedures with respect to mineral development on Railway Co. lands and may be referred to for information on these matters.1 In a sense this paper is a progress report on the use of geochemical prospecting in Northern Pacific's continuing mineral evaluation program. At this time there are positive results but as yet there is no real success story in the form of a minable ore body. GEOCHEMICAL PROSPECTING PROCEDURES The decision to use geochemistry as a reconnaissance exploration tool must be followed by research into sampling and analytical methods and into the interpretation of results. Various analytical methods were tried and evaluated by the Geology Div., including hot and cold acid extraction with and without fusion of the sample, panning and magnetic separation followed by dithizone testing of the magnetite, and cold aqueous extraction of metallic ions followed by indicator tests. Samples were first sent to the laboratory for analysis; later field laboratories were established and now virtually all testing is done at the sample site. It was concluded that, where applicable, the quickest dependable methods for reconnaissance use are the dithizone field tests for readily extractable heavy metals. This involves the simultaneous treatment of a sample, usually of soil or stream sediment, with two immiscible liquids; one a cold aqueous extractant (ammonium citrate) and the other a solution of dithizone in toluene or xylene.2 Dithizone is a colorimetric indicator that reacts quantitatively with copper, lead, zinc, and several other metals to form colored complexes in organic solvents. Results may be expressed in ml of 0.001 pct dithizone that are required to reach the blue end point, or calibration of the test results can be carried out with standard solutions of zinc; conversion factors would then be expressed in ppm, zinc equivalent. Calibration of dithizone solution with zinc standards indicates that 1 ml of 0.001 pct dithizone is equivalent to approximately 0.25 ppm of zinc. An authoritative report on dithizone field tests authored by H. E. Hawkes in the June-July 1963 issue of Economic Geology* states "The appeal of these techniques has been the simplicity and speed of the determinations as compared with more tedious laboratory determinations of trace metals in weathered rocks, soils, or plant materials. This obvious appeal, however, has often been more than matched by misuse of the method in such a manner that the results are

Jan 1, 1964

By R. Schuhmann

D. W. Fuerstenau (Associate Professor of Metallurgy, Dept. of Mineral Technology, University of California, Berkeley, Calif.) In his excellent paper, Dr. Schuhmann has proposed a mechanism for conlrninution which can be utilized to explain a number of phenomena which have been observed in the size reduction of solids. The difference between the product obtained from a ball mill and from a rod mill can readily be explained by Dr. Schuhmann's hypothesis. Consider that the size distribution of the product from each comminution event is given by y; - 100 (x/ki) (1) where Yi is the cumulative percent finer than size x, ki is the size modulus, and is the distribution modulus for the single comminution event. The total product from a cornminution operation will be the summation of the products from all of the individual cornrninution events. If the size moduli from the various comminution events range from kl to kn , the size distribution of the total product will be a straight line on a log-log plot only to a particle size equal to k ,. Considering 100 volurnes of feed, the value of y for x equal to kl is Riven by where y is the cumulative percent finer than size kj, z is the number of comminution events of kind i, and vi is the volume of each particle crushed. y=z1 qv1+z2 qv2 (k1/k2) +.............zn qvn (k1/kn) (3) F or particle sizes greater than k1 7 e. 6. x = k3, the value of y will be given by k3 A y = z1 qv1 + z2bv2 + Z3uV3 + zn zn qvn (k3/kn)(4) Only when x is equal to k, will y equal 100. 'Thus, the total product from a comminution operation will be a straight line on a log-log plot strictly up to a particle size equal to kl and above that size the line will curve so that y will equal 100 for the coarsest particle or k, (see Fig. 1). The actual shape of the size of distribution curve will depend upon the relative number of conmninution events of different kinds. In the case of ball milling, the ratio kn/kl may be pite large and there will be considerable deviation at the coarse sizes in a Schuhmann plot. kIowever, the grinding action in a rod mill is such that fine particles are protected from the rods by the coarse particles. Consequently, kn/kl will be quite small and the product from a rod mill will give a straight line Schuhmann plot almost to y equal 100%. In his paper, Dr. Schuhmann also has presented a very straightforward definition of grindability derived from the basic energy equation E = Ak-a (5) where E is the energy required to comminute a material to a size modulus of k and A is a constant. According to Dr. Schuhmann, the grindability of a material is the volume of material comminuted finer than unit size per unit of energy expended, this being 1/A. For comparison of grindabilities at any size two numbers are required, both = and 1/A, and anyone tabulating grindabilities should give both of these numbers. Concerning the experimental determination of grindabilities, if the material being comminuted possesses distinct cleavage, the energy re quired for comminution is given by E = Ak-(a-y) (6) where y is small number less than = . Because of cleavage, less energy will be required for comminution. To be certain that cleavage does not affect the gindability of the material being tested, it is suggested that the method used by Dr. Charles for determining grindability be used to ascertain if the deviation exponent y is zero or finite. R. Schuhmann, Jr. (Author's Reply) Dr. Fuerstenau's interesting comparison of rod milling and ball milling

Jan 1, 1961

By Frank J. Tolonen, Nicholas H. Manderfield, Paul Jasberg

EARLY in the study of the low grade iron formations of Michigan, wide variations in their structure and texture became evident. Because of these variations no simple method of concentration is possible, and those portions of the formations that can be exploited profitably under a given stage of metallurgical progress and existing economic conditions must be searched for carefully. Both structure and texture of the formations have an important bearing on their amenability to bene-ficiation. By structure is meant the banding planes of easy fracture, the porosity, and the degree of leaching. Texture, which includes grain sizes, shapes, and degree of interlocking, determines the amount of grinding necessary to liberate the mineral grains. Structure determines the liberation of portions richer in one mineral. Structure and texture may be termed the gross features of the formation. Earliest surveys of the formations were conducted to outline the parts that could be concentrated at % in. (3 mesh). Operators agreed on this size because anything finer required sintering or other agglomeration processes. At 3 mesh only the structural features, as defined above, would be liberated. With suitable ores concentration was easy, as any of the gravity methods could be used. Sink-and-float gave good results, but with this method only limited portions of the iron formations yielded a desilrable product.1,2 n general, the iroa content could be raised to shipping grade, but the silica content remained too high—sometimes 20 pct—instead of 9 or 10 pct. Grinding did not greatly increase the liberation ofsilica until 2010 mesh or finer was reached. To find the reason fpr this T. M. Broderick began micros~opic examin'ations of the formations in 1933.3 Procedure: The purpose of this discussion is to correlate the appearance of typical portions of the iron formations with their amenability to concentration. As liberation is essential before separation becomes possible, much of the work is based on measuring the liberation achieved by crushing and grinding. Both heavy media and magnetic tube tests were used in this work. On the basis of general structural features such as banding, degree of alteration, and leaching, a specimen was selected from each part of the iron formations studied. The specimen represents the gross features of the formation and not necessarily the particular formation quantitatively. One half of the specimen was polished for macro-study, and the remainder was used for analyses to obtain the grades represented by variations appearing in the macrosection. Specimens for microscopic examination were also prepared for each variation in gross appearance. For correlation of microstructure with liberation, the previous work by sink-and-float methods was supplemented by magnetizing roasting followed by magnetic separation. The results show the liberation of silica to be very important at the sizes used, because any silica particle with iron minerals occluded would be held in the concentrate. A magnetizing roast changes the crushing and grinding character of the sample. For partly leached soft samples the change is slight, but with harder types and those in which there is a considerable change in crystal structure of the minerals, the increase in liberation of the iron minerals may be 30 pct more than that of unroasted samples at the same crusheH size. Gogebic Range Iron Formations: The Gogebic Iron Range is located in the extreme western and southern parts of Michigan's Upper Peninsula, extending westward into Wisconsin. Samples for this study were obtained from the Ironwood formation, comprising three chief members—the Plymouth, Norrie, and Ahvil—with several intermediate slates and thick overlying slates. (The slates are not considered in this discussion because grinding finer than present practice is usually required to liberate the iron minerals.) The predominant iron mineral is hematite, about half of which is hydrated to goe-thite. Limonite occurs in some of the partly leached areas, and siderite in parts of the formation.

Jan 1, 1958

By Strathmore R. B. Cooke, Iwao Iwasaki

RECENTLY spectrophotometry has been reported to provide a convenient technique for the rapid and reproducible determination of xanthate concentration in pulp solutions,12 and for a kinetic study of xanthate decomposition in acid solutions." Since the application of this analytical technique is feasible for those compounds showing pronounced light absorption maxima in the near ultraviolet region, it was deemed advisable to investigate the absorption spectra of some of the organic compounds that are used in flotation. It is known empirically that certain groups of atoms in an organic compound cause characteristic light absorption in the ultraviolet and near ultraviolet range, and the wavelengths and intensities of the corresponding absorption maxima are relatively independent of the nature of the remainder of the compound. The characteristic values of such groups, which are known as chromophores, are given in the literature.4,5 According to this information, many of the sulphydryl compounds are expected to show absorption maxima in the near or long wavelength ultraviolet region, whereas the saturated fatty acids and the saturated alkylamines do not. This article reports the absorption spectra of the six following types of sulphydryl compounds; mono-, di-(xanthate), and trithiocarbonates, dithiocarba-mate, dithiophosphate (aerofloat), and mercaptan. A Beckman DU quartz spectrophotometer was used to investigate the spectra in the wavelength region of 215 to 350mp. Materials: All the mono-, di-, and trithiocarbonates used in this investigation were prepared in the usual manner" from appropriate compounds obtained from Eastman Distillation Product Industries. The dithiocarbonates included the normal alkyl compounds from methyl to octyl inclusive, as well as the isopropyl, isobutyl, and isoamyl xanthates. Iodo-metric titration gave 99.7 and 99.5 pct purity for

Jan 1, 1958

By J. Blodget Britton

Six different samples of anthracite, each a firm compact lump, were finely pulverized and immediately put in bottles. Portions of these were weighed and placed upon an ordinary water-bath and dried for one hour; the average loss was 1.24. The same portions were then placed in a hot-air oven, and for two hours kept at a temperature of 285° F., and, after cooling in a dry chamber, were again weighed, when there was found a further average loss of 1.22, making a total so far of 2.46. They were then immediately returned to the oven and for two hours more kept at a temperature of 530° F. and cooled and weighed again, when no further loss was found, but an average gain of .55 upon the previous weighing. The same portions were a third time placed in the oven and for about ten minutes kept at the last-mentioned temperature, and then, while still hot, were poured into one-quarter inch glass tubes, each with a bulb at one end, and heated over a Bunsen burner at a temperature below a red heat, when more water vaporized and condensed in small clear globules on the cold parts of the tubes. Fresh portions of the coals were then taken, and the total amount of water determined, and the average was found to be 3.04, or 1.80 more than was found at the temperature of the water-bath, which was perhaps a little below 212° F., and .58 more than at 285° F. Tests were afterwards made by placing other fresh portions of the

Jan 1, 1877

At their last meeting, the Directors of the Institute passed the following resolution regarding Robert W. Hunt, who was president of the Institute in 1883 and 1906. This resolution was engrossed and presented to Captain Hunt at a dinner given to him in Chicago, December 9, on the occasion of his eightieth birthday. Resolution At that time it was announced that $5000 had been guaranteed as the nucleous of a fund, the income of which will be used for prizes to be awarded each year, under the supervision of the American Institute of Mining Engineers, for the best papers on iron and steel subjects. The Board of Directors of the American Institute of Mining Engineers extend to their distinguished colleague, Robert W. Hunt, a hearty greeting upon his eightieth birthday anniversary. They congratulate him upon his notable achievements as a pioneer in ,the manufacture of iron and steel, and his long and admirable service both as a practical director and as a wise critic and counselor in that art. They remember with gratitude his successful administration, for two separate periods, of the Presidency of the Institute, and they recall with pride the honor conferred upon it through the award to him of the John Fritz Gold Medal. Not least is their satisfaction in the retrospect of forty-four years of his membership in the Institute, with its unbroken record of loyal friendship acid delightful companionship; and they pray, that this record may be continued for happy years to come. In witness whereof, they have ordered this minute to be entered upon the records of the Board, and a copy duly attested to be sent to Captain Hunt.

Jan 1, 1919

By M. E. Shank, J. Wulff

In view of the current interest in magnetic materials having rectangular hysteresis loops, as for example those obtained with the grain oriented 50 nickel 50 iron alloys,t we wish to call attention again to the results obtainable with the perminvar (Co-Ni-Fe) alloys heat treated in a magnetic field. Data taken from direct current measurements made prior to and during World War II give the typical values shown below for two of the perrninvar alloys. Fig 1 and 2 show- the hysteresis loops for these samples. The first sample above consisted of small rings punched from 0.014 in. sheet stock. These rings were heat treated at 1000°C for one hour in a hydrogen atmosphere and then cooled with the furnace to 750°C at which point they were subjected to a magnetic field of 15 oersteds maintained during cooling to room telmperature. The molybdenum perminvar sample consisted of a spirally wound core of 0.001 in. tape. The heat treatment was the same except that box annealing methods were used and no hydrogen atmosphere was employed. Even better properties might be expected using hydrogen. The heat treating temperatures and cooling rates are not critical. Rectangular hysteresis loops produced in other perminvar alloys by heat treatment in a magnetic field were described earlier.',? Properties similar to those described above are realized in perminvars manufactured by conventional methods. Drastic cold working which in practice limits the final thickness and is gen- erally expensive may thus be avoided. This information may be of interest to those concerned with magnetic alloys and the development of contact rectifiers, magnetic amplifiers and so on.

Jan 1, 1950

By Howard Drullard

To OBTAIN the best results from hammer drills, close attention must be paid to two factors in drill maintenance, which are of equal importance; one is lubrication, the other is the shank. With the exception of stoping drills, most modern rock drills require both oil and grease. The oil ports are in the lubricator, on or behind the hammer cylinder; the grease port for the lubrication of the 'chuck sleeve and rotating mechanism is on the chuck end. Ordinary machine oil is not, adapted to rock drills; a heavier more gelatinous oil such as castor machine oil or liquid-grease should be used. The lubricators should be filled-once for every 12 or 14 ft. (3.5 to 4m.), of hole drilled. Grease-guns should be used to fill the port in the chuck end once a shift; a medium ( No. 3) grease is well adapted to this purpose. Hard grease must not be put into- the lubricators, as it will not flow through that part. Contrary to the popular belief, oiling a machine once or twice a shift does not provide sufficient lubrication; the drills should be oiled once for every 12 or 14 ft. of, hole drilled. The rotating handle of a stoping drill -is an oil reservoir and is provided with a port for oiling. The rotating handle is packed with wicking, or similar material, which causes the oil to feed slowly from the handle to the other parts of the machine. Stoping drills require oil at. least twice a shift; lighter oils than castor, such as Arctic Ammonia may be used.

Jan 8, 1920

By Howard L. Hartman

Probably no aspect of underground excavation is as important or as neglected as the environment. The Committee on Rapid Excavation, formed by the National Academy of Engineering to study the technological needs for "rapid" underground excavation in tunnels, shafts, and mines of the future, encountered a blank wall in attempting to evaluate environmental needs. In fact, so little quantitative information on the extent of present-day hazards is available that projection of future environmental-control demands must await more adequate assessment of current hazard levels. Further, there are not even accepted tolerance standards for many environmental conditions, such as heat, noise, and illumination. Only certain atmospheric contaminants have been satisfactorily catalogued. Any technical study, therefore, which purports to examine the state-of- the-art on underground environmental control must, in reality, settle for a cursory survey of a rather nebulous subject. ENVIRONMENTAL HAZARDS To contend adequately with hazards in the underground environment requires some knowledge of their nature and characteristics. In this regard, it is helpful first to identify our concern: when, where, and to whom or what may environmental conditions constitute "hazards"? Table 1 summarizes considerations that are important in this regard. For the purposes of this Conference (and book), primarily directed toward the excavation process itself, the hazards of consequence occur during excavation (item A) and primarily within the excavation (item B). However, some attention must be given to external hazards as well, since these may affect excavation. The object of concern (item C) is mainly human safety, although property security is also important. Hazards occur in a variety of forms. If one is to devise suitable control

Jan 1, 1970

By M. T. Abasov

Among a host of challenges dictated by the explosively developing scientific and technical revolution, the improvement of control and management is one of the most essential problems. This problem is also of far-reaching importance for the oil and gas industries. An oil and gas extracting complex is an involved multilink system characterized by a great number of elements and by intricate interconnections between these elements. Of paramount importance for these systems is the quality of control. Any deviation of the control from the optimum reduces the effectiveness of the system and deteriorates its basic technical and economic factors. In case of large systems, even a relatively small deviation from the optimum may result in considerable material and power losses. Optimization of control of large production systems is therefore one of the basic means to enhance their effectiveness. The present paper discusses a development control problem for a multilayer gas deposit using the method of simultaneous exploitation of several strata by means of a single well. The optimum control is achieved by determining the dynamics of changes in the number of producing wells in a reservoir with regard to the depth of occurrence of these reservoirs as well as the difference in the time of introduction of the wells from drilling and their transfer to another reservoir. A mathematical model was constructed for the problem under consideration and a method was given to solve this problem. The problem was dealt with under the assumption that either each of the reservoirs or a part of them have vertically overlying areas and that there is no hydrodynamic interference between the horizons. It was

Jan 1, 1977

By C. H. Noren

For some years the Du Pont Company has utilized computer calculations to study the various theoretical properties of explosives. These studies have yielded valuable information on the effects of density changes or formulation changes on detonation rate, detonation pressure, explosion pressure, heat of explosion and numerous other properties, and have aided in evaluating the theoretical potential of explosives. In addition, a multitude of laboratory tests have been utilized for the evaluation of explosives. When comparing the computer data and the voluminous test data it became evident that numerous anomalies existed. Tests in rock were required to study explosives under borehole confinement. This fact was further emphasized after numerous field measurements showed that the borehole velocity of commercial explosives did not match the theoretical value but was dependent on conditions of field use. Since we are interested in the practical aspects of blasting, a program was initiated to evaluate explosives as used in commercial blasting. INSTRUMENTATION Most of you are familiar with the extensive work that has been done by the U. S. Bureau of Mines in their studies of strain measurements in rock. Early in our work we adopted procedures similar to those used by the Bureau of Mines. Strain pulses were measured by gages cemented in boreholes. Since we were primarily interested in the effect of explosives in the zone where fracture might occur, this system offered several disadvantages for Du Pont: 1. Cemented gages were expensive and not reusable. 2. When gage holes were used for several shots, there was considerable question as to the condition of the rock after the first shot.

Jan 1, 1968

By K. Kim

INTRODUCTION A thorough evaluation of the geologic material being considered must be conducted to determine the feasibility of constructing a large-scale underground facility in a deep geologic formation. The design and construction of a nuclear waste repository in basalt, due to the unprecedented nature of the project, adds significantly to the need for thoroughness of this evaluation and mandates that geoengineering data and analysis be of the highest quality. The investigations required to collect the data encompass in situ measurements and observations, as well as laboratory and field tests. Mathematical (numerical) models, which are required to predict the long-term performance of the repository structure, must be developed to evaluate rock mass behavior at canister, room, and repository scale and eventual 1 y must be validated through in situ tests and monitoring. The information generated from these geo- mechanics investigations is essential for assessing site suitability and will be utilized in the development of the repository design, the engineered barrier design, and the evaluation of repository performance. The Hanford Site near Richland, Washington is one of nine sites throughout the nation being investigated by the U .S. Department of Energy as a possible location for the first high-level nuclear waste repository in deep geologic formations. The process of site characterization is currently in progress. If the site is nominated by the U.S. Department of Energy, an extensive program will be undertaken, the culmination of which will be a decision on the suitability of the site for waste disposal. There are a mu1titude of elements to the proposed site characterization

Jan 1, 1984

By C. M. Signer, W. P. Hewitt

THIS is a story of a mine discovered in the days of the Conquistadores but that remained unimportant until the second decade of this century. Without the usual legendary history of romance and fabulous riches it has become famous for the development of unexpected metals and unusual problems. These developments and experiences, exciting and interesting as any legend, are the substance of the San Antonio mine of the Santa Eulalia district in northern Mexico. Originally opened for its silver-lead content, it developed a tin deposit of singular economic importance and unique geologic interest, a vanadium orebody that for a few years placed it among the leading vanadium producers of the world, and now lead and zinc sulphide ores. It has been the seem of a disastrous flood that brought deep-sea divers into Mexico's desert mountains and raised important problems regarding ground water, demanding unusual measures. Geology and operating questions relating to the above matters will be discussed and much of it is recent history which has become a part of Mexican mining lore. History Dates Back to 1325 Santa Eulalia is the oldest of American cities, founded in 1325 by the Aztecs under the name of Tenochtitlan and devastated in 1521 by Cortes and his rapacious band of iron-willed adventurers. Their lust for gold burned through the Aztec empire and onward into most of North America. Santa Eulalia was in the path of conquest. In 1591 the district's first ore discovery was made near what is now the San Antonio mine. The ores carried no gold and the silver-lead content was unattractive to the early pioneers. Not until 1700 was real mining activity undertaken.

Jan 1, 1952

COLLECTIVE bargaining, hereto-fore loudly proclaimed as one of the stout timbers of the Republic, has passed from the picture. The coup de gr[a]ce was struck by the President of the United States when he ignored his vested legal prerogative and seized the steel industry by the dubious authority of, his "inherent powers." Autocratic judgment by a single official replaced arbitration by the steel industry and labor union. This is the outcome of a battle which has been bitterly waged for months in the hazy atmosphere created by well oiled propaganda machines. Prior to government intervention, there was no clear picture of the issues at stake. All parties concerned marshalled their accountants to conjure up figures proving their respective contentions. The results were fed into public relations departments for embellishment and dissemination. Thus, the public was asked to believe on one hand, that the steel worker, who is second only to the coal miner in hourly wages, was entitled to an increase in pay and other benefits. Nothing was said about the effect-of such an increase on the national economy. Industry in turn pointed to declining profits after taxes, but failed to mention the more than a billion dollars spent on plant expansion, in addition to the payment of substantial dividends for 1951. With the intervention of the administration, the immediate issue became clear to freedom-loving Americans. Is the executive branch of the government above the law, or is it supposed to uphold and carry out the .laws of Congress? The present administration forgot that it is a servant of the public and has become despotic. The American people must obliterate this dangerous precedent which has been set by the administration or accept the. ominous consequences of submission. Fortunately, the strongest weapon of the citizen-the ballot -still remains. When democratic procedure is restored, stabilization of the economy will continue to challenge us. This is the main public stake in the steel controversy. Only a solution based on bed-rock democracy will work. If the emergency is real, and we must assume that it is, this is the time for sacrifice. Industry and labor must meet without rancor to resolve wage contracts through collective bargaining. The government role, under emergency conditions, must be to objectively maintain wage, and price ceilings in the interest of stabilization. Political expediency cannot be permitted to' influence these controls. Politics and not the public weal have been the guide lines for too long. We are at the cross roads. By all sober judgment, this is the time for Americans to take a militant interest in their government today. Tomorrow will be too late.

Jan 1, 1952

By James Hyslop

THE Pittsburgh seam in eastern Ohio has an average thickness of 5 ft and lies almost level Immediately above it is a layer of draw slate about 12 in thick, which normally has little structural strength, and is pulled down or allowed to fall as mining progresses Above the slate is a, variable thickness of roof coal, which in places will stand for the life of the working section and sometimes for the life of a secondary haulage entry The thickness of this roof coal varies from zero to 24 in In general, however, it does not provide a satisfactory roof, and usually is supported or pulled down About it is a mass of shale, soapstone and clay, of quite variable thickness, usually running from 5 to 8 ft and above this is a stratum of hard blue limestone, which provides a permanent roof Where entries are to be used for less than five years, the roof usually can be supported by wood or steel crossbars, but if they are to be used for a longer time, roof support is a serious problem All the roof material below the limestone disintegrates when exposed to air or moisture, and in a few years falls out between and over the crossbars Where this material is removed for a considerable height above the coal, the ribs scale and thus contribute to a further collapse of the roof As the height of the entry increases, cost of timbering is greatly increased, a problem that always is encountered where old entries are recovered or repaired METHODS During the last six years the Hanna Coal Co has used gunite for roof protection in mine entries Two general methods of guniting are practiced The first consists of the application of a I-in coating of unreinforced material This application does not provide any appreciable structural strength, and serves principally to protect the strata from exposure to air and moisture With the other method a coat at least 2 in thick is applied and provided with suitable reinforcing, which provides a structural strength proportional to the thickness of the coat and the reinforcing used The first method is adopted as a general practice, modified only where additional support is required "Gunite" is a mixture of cement, sand and water * The cement and sand are thoroughly mixed and screened before being fed into the hopper of a cement gun After the hopper lid is closed, compressed air is applied to force this dry mixture through the hose line to the nozzle, where the quantity of water needed to effect the proper hydration of the cement is added The coating is dense, and stronger than poured concrete

Jan 1, 1941

By J. R. Cahoon, W. V. Youdelis

In a recent publication by Flemings and Nereo, equations for the calculation of the solute distribution in castings were developed, and the solute distributions for unidirectionally solidified A1-4.5 pct Cu ingots cast under various thermal conditions were calculated. The equations derived by Flemings and Nereo for the dendrite "expansion" and "steady-state" zones are essentially equivalent to those previously published by Kirkaldy and Youdelis, 16 for, although the flow velocity cooling rate, and temperature gradients appear in the fundamental differential equations, calculation of the solute distribution requires that the above be explicitly related to the assumed or measured solid-liquid mass distributions during solidification. In the treatment of Kirkaldy and Y-oudelis the mass distributions are simply assumed or measured without any prior and explicit association of the mass distributions to a velocity parameter. The treatment of Flemings and Nereo permits solidification conditions more complicated than the simple unidirectional case to be considered (although in principle the treatment of Kirkaldy and Youdelis could also be extended to include the more general solidification case); however, we note some limitations in the treatment of Flemings and Nereo, and the purpose of this discussion is to point these out and also to indicate those points of similarity in the mass distribution models used which make the two treatments equivalent. Both the Kirkaldy-Youdelis and Flemings-Nereo treatments consider a zone of dendrite "expansion" followed by a "steady-state" zone. However, Flemings and Nereo have failed to consider a zone of "collapse" which begins at the base of the first dendrites to reach the top of the ingot. The omission of this zone of "collapse" results in too high a value for the solute concentration in the latter portion of the ingot to solidify and the conservation of total solute is not possible. In the zone of "collapse" the solute concentration rapidly decreases, which may be accounted for as follows: consider a mushy zone of length X,, shown schematically in Fig. 11 (a), which develops at the chill face and then moves as a steady-state configuration along the length of a solidifying ingot. The solute distribution in this zone, when it first attains the steady state, is shown qualitatively in Fig. 11(b). The segregation is positive (above Co) in the region ab because this region contains primary dendritic solid, ranging from kco to kcE in composition (where k is the partition coefficient and CE is the composition of the eutectic liquid), and liquid metal near eutectic composition. The segregation is negative (below Co) in the region bc because it contains primary dendritic solid only slightly above kco in average composition and liquid metal only slightly above Co in composition. As the zone X, moves as a steady state

Jan 1, 1969

By J. S. Osoba, J. G. Richardson, F. M. Perkins

Laboratory experiments have shown profound diffcrences in the behavior of so-called "fresh cores" from the East Texes field and of the same cores after ex~ractio~l with organic solvents. The residual oil satura/ion remaining after waterflooding fresh cores was appreciably lower than the corresponding saturations after flooding extracted cores. This behavior was also reflected in the water-oil relative permeability-saturatiorl relations, which were more favorable for high oil recovery from the fresh cores. These differences were evident not only in the amount of residual oil left after wafer flooding, but also in the saturation water remaining in the core after displacernent by oil. Residual water saturation after displacernetzt of water by oil was higher in the fresh cores than in the extracved core,. Capillary pressure-saturation relations were also different for the fresh crnd extracted cores. Imbibition experiments indicated that both fresh and extracted Bast Texas cores imbibed water spontarteOLISIY, but- the rate of imbibition of water was higher for samp1es after. extraction than it was for fresh core. material. INTRODUCTION Several years ago a series of waterflooding tests was made in the laboratory on a number of Woodbine core samples from the East Texas field. These samples had been stored in containers open to the air and were extracted with organic solvents before they were subjected to the laboratory tests. After water flooding, the residual saturation of kerosene, which was the oil used in the tests, was found to average about 30 per cent. This saturation was higher than expected. In investigating the circumstances which might have been responsible for such a high residual oil saturation, attention was given to possible changes in wetting properties of the rock brought about by the procedure employed in extracting the cores. Preliminary results indicated that the explanation for the high residual oil saturation lay in the wetting behavior of the cores, though what effect extraction had on this behavior was not clear. In consequence, the work described in this report was undertaken in an attempt to investigate the mechanism responsible, and to ascertain the actual residual oil saturation to be expected in the reservoir after water flooding. It was soon found that there were profound differcnces in the behavior of so-called "fresh cores" from the East Texas field and of the same cores after extraction with organic solvents. These differences were evident not only in the amount of residual oil left after water flooding, but also in the saturation of watet remaining in the core after displacement by oil. The complete explanation of this behavior is not yet apparent. The description of work and results described in following sections, therefore, must be considered as an interim report presenting facts which must await additional information before they can be fully interpreted.

Jan 1, 1956