Search Documents

By R. E. Reed-Hill, W. H. Hartt

High-purity magnesium single crystals, oriented with basal plane parallel to stress axis, were deformed in tension at room temperature so as to form second-order (1011)- (1012) twins. Investigation by optical and replica electron microscopy revealed that these twins can support very large internal strains approaching 1000 pct and that fracture follows as a direct consequence of these strains. At low strains the basal plane within (10i1)- (10i2) twins rotates with increasing deformation until it becomes approximately parallel to the twin boundaries. This rotation is not consistent with deformation by basal slip in the double twin, but may be rationalized in terms of nonbasal slip. Observations also indicate that basal slip in the primary (1011) twin, prior to second-order twinning, may contribute to this rotation. Deformation markings that are difficult to interpret in terms of slip on previously observed systems were noted in the twin bands. A possible means of rationalizing these markings is to relate them to grain boundary shear. The fracture associated with these twins is thought to initiate by formation of voids at the twin boundaries. These grow into microcracks, with ultimate fracture occurring by tearing of the interconnecting regions. THE significance of deformation and fracture along second-order (10i1)-(10i2) twins in polycrystalline magnesium1-' and many magnesium alloys4 was discussed in a previous paper.5 It was noted that this double twinning mode effectively controls the room-temperature deformation and fracture of magnesium single crystals, oriented with the basal plane parallel to the tensile axis. Reed-Hill and Robertson6 observed that, although these crystals may fracture at a macroscopic strain of less than 1 pct, shear strains up to 1000 pct could occur within (1011)- (10i2) twin bands. They concluded that the fracture was "ductile" and resulted from concentrating the deformation into a very small volume. The present research was undertaken to obtain a better understanding of the deformation and fracture associated with these twins. EXPERIMENTAL TECHNIQUES The experimental procedure involved straining high-purity magnesium single crystals in tension at room temperature. Specimens were oriented so that the applied stress direction was within 2 deg of the [1010] crystal axis. The specimen cross section was rectangular with faces closely parallel to (1210) and (0002). The specimen preparation and testing procedures have been described in detail elsewhere.5 Second-order (1011)- (1072) twins nucleated during straining were studied using optical and replica electron microscopy techniques. For the latter, cellulose acetate-carbon double replicas were employed. Observations were made on the (1210) crystal surface, which is the plane of shear for twins of this type. In addition to the single crystals, some investigations were carried out on longitudinal polycrystalline specimens. These were obtained from high-purity magnesium plate with a texture in which the basal planes of the grains tended to be nearly parallel to the specimen axis. All. polycrystalline specimens were annealed prior to testing in order to produce a coarse grain structure, permitting Laue back-reflection X-ray photographs to be obtained from grains of interest. EXPERIMENTAL RESULTS a) Deformation Within ( 101 l )-( 1072) Twins. Fig. 1 is an optical micrograph demonstrating the extent of the plastic deformation that can occur in (1011)-(10i2) twin bands. Notice at the lower left corner of the photograph the large displacement of the dark band (a polishing step) where it crosses the twins. The shear strain in the twin band at this position was computed to be 700 pct, using the ratio of step width to twin thickness. It was previously shown5 that (1011)- (1012) twin bands are often composed of small, separate twins aligned close to the macroscopic habit plane. Fig. 2 is an electron micrograph from near the upper end of the twin band in Fig. 1. This illustrates that the twin habit often does not coincide exactly with the macroscopic band habit, but may be inclined at a slightly smaller angle to the matrix basal plane. Figs. 3 through 6 are electron micrographs of the twin band in Fig. 2 illustrating successive steps in the development of deformation inside the band. A twin band such

Jan 1, 1969

By Jr. Ensign C. O., J. W. Trammell

The two principal methods of room-and-pillar mining practiced at White Pine make it important to predict variations in the thickness and rock types of a stratum called the upper sandstone. In full column mining, the nearly barren upper sandstone occurs between two ore horizons (called upper shale and parting shale, respectively), and is mined as a part of the ore column. In general, full column mining is not practiced where excessive upper sandstone thickness causes full column ore grade to be substantially lower than parting shale ore. In parting shale mining, the upper sandstone forms the mine roof. Difficulty in predicting upper sandstone character arose because the extent and directions of its variations were not apparent in the property's diamond drilling, in which holes are spaced on 1000-ft centers. A study of sedimentary features, undertaken to improve the predictability of trends in the upper sandstone, led to an interpretation of the sedimentary environment in which the sandstone was deposited. Ripple marks, mud cracks, and cross-bedding, as well as other, less well known features, such as channel casts, flute casts, and current crescent casts, were mapped or recorded. These data, coupled with the knowledge of regional facies changes gained from studying drill core, show that the upper sandstone was deposited by a series of streams flowing northeastward over the underlying parting shale. Deposition of the lowermost bed of the upper sandstone, near the ancient shoreline, was locally preceded by erosion of the parting shale, and the greatest thicknesses of sandstone are found in channels scoured out of the parting shale. Awareness of the rather strong linear trends in the upper sandstone makes it possible to project continuous areas of thick upper sandstone through apparently isolated "highs" in the upper sandstone thickness contour map, which is based on drill-hole information. Since local exceptions to general stratigraphic trends exist, a method was also needed for esti- mating, in detail, the thickness and degree of shali-ness of upper sandstone forming the roof in active parting shale mining areas. Because locally the parting shale was thinned by erosion during the deposition of upper sandstone, parting shale thickness is inversely proportional to upper sandstone thickness. Utilizing information taken from short drill holes into the roof, curves were constructed for the correlation of parting shale thickness (measurable in the mine) with the upper sandstone total thickness, as well as the thickness of its basal member. The White Pine mine is situated in Ontonagon County, approximately 6 miles south of Lake Superior, in the Upper Peninsula of Michigan (Fig. 1). The orebody mined by White Pine Copper Co. occurs in the lowermost 20 to 25 ft of the Nonesuch formation, a series of middle- to upper-Keweenawan shales, siltstones, and sandstones. This paper discusses the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the orebody. THE OREBODY AND MINING TYPES A brief description of the orebody and mining methods is necessary to show how the upper sandstone affects mine planning and grade control. In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions, as shown in Fig. 2. Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 2. Other authors1'3 have dealt in detail with the stratigraphy and mineralogy of the orebody. However, in this article, we are concerned with the major subdivisions only, and it will suffice to note the low copper content of the upper sandstone, shown in Fig. 2. At present, two types of room-and-pillar openings are created in the orebody. In one type, called parting

Jan 1, 1964

WALTER E. GASP, Vanadium, Colo. (communication to the Secretary*).-Having enjoyed associations with the authors of this paper while on the Anaconda geological staff, I want to express my appreciation of it as a contribution to economic geology very direct in its application to ore deposits. The conclusions reached seem to me to show that concrete generalizations can not be made over very wide areas as to structural relations of ore deposits, but taking each district separately data of great value has been presented. Looking over thin sections of Montana rocks, among these a collection belonging to Mr. Billingsley and some prepared by myself, one important point in the Butte area has come to my attention which I would like to discuss. Related to the batholithic intrusion, there are a number of various types of both the earlier andesites and the later rhyolites, especially of the rhyolite. Some of this rhyolite is composed- so predominantly of plagioclase and quartz as to be more properly called dacite, and near the volcanic centers the different phases are even more numerous, the quartz in some becoming a very minor constituent and confined to the ground-mass. Some portions of these rhyolitic extrusives assume ,deep reds and grays, and in the hand specimen may very easily be mistaken for andesite of the older period that has been altered by weathering or by baking near the intrusive granite contact; but thin sections of such specimens remove this color effect and present so clearly all the minute details of texture and mineral composition that they are in every respect identical and indistinguishable from the commoner types of the rhyolite. The andesites generally are augitic rocks with smaller plagioclase feldspars than the rhyolites and exhibiting a different arrangement. Therefore the so-called red and Clark gray andesite near Butte is not a portion of the pre-batholithic rocks, but a. phase of the rhyolite, and the authors, in assuming that "roof pendants or large inclusions of andesite are found

Jan 10, 1917

By J. W. Spretnak, G. W. Powell, J. H. Bucher

Tlze room-temperature tensile fracture oj smooth, round specitnens of three ultrnhigh- strength steels tempered to a wide range of strength levels was studied by means by light and electron-microscopic examination of the fracture surfaces. The fracture of AISI 4340 and 300 M at all the strength levels studied, and H-11, except after tempering at 1200° and 1300°F, occurs in three stages. The initiation of fracture is internal (except in some lightly tcmpeved specimers in which fracture is initiated at surface flaws), and is nucleated largely by separation at metal-second phase intevjaces. TIze voids grow and, coalesce to form a crack. When the crack has reached a sufficienl size, rapid propngutio~z ensues. Failure in this stage of fracture usually occurs by dimpled rupture of inicroshear stefis. In the case of H-11 tempered in the 1125° to 1300°F range, fracture in the shear steps is predominantly by concentrated deformation without void formation. The termination of fracture is usually occomplished by the formation of a shear lib in which fracture occurs by shear dimpled rupture. In the case of H-11 tempered at 1200° and 1300°F, no shear lip was obserued, and the radial elelments extend to the surface—a true termination slage does not exist. ThE tensile fracture of several metals and alloys has been investigated.2-4 In the case of polycrystal-line materials, cup-cone fracture usually results. The mechanism of cup-cone fracture may be summarized as follows.5 Cavities are formed in the necked region of the specimen. They usually are initiated by inclusions or second-phase particles. The cavities extend outwards by means of internal necking, and a crack lying about perpendicular to the length of the specimen is formed in the necked region. Subsequent crack growth occurs by the spread of bands of concentrated plastic deformation inclined at an angle of 30 to 40 deg to the tensile axis. Cavities are formed in the bands of concentrated deformation. The deformation bands zigzag across the bar with the net result that mac-roscopically the crack extends about perpendicular to the specimen axis. The final separation, or cone formation, appears to occur by continued crack propagation along one of the deformation bands out to the surface of the specimen. The micromechanics of the tensile fracture of ultrahigh-strength steels have not been thoroughly investigated. Larson and carr6,7 studied the tensile-fracture surfaces of AISI 4340 with a low-power microscope and reported that three stages of fracture could be observed in general. A centrally located region characterized by circumferential ridges, an annular region characterized by radial surface striations, and a peripheral shear lip were found. It was first pointed out by 1rwin8 that the central region is very probably one of fracture initiation and slow growth, and that the annular, radially striated region is one of rapid crack growth. Presumably the crack grows slowly, assuming roughly a lenticular shape, until it is large enough for the initiation of rapid propagation. In this investigation, it was attempted to determine the fine-scale aspects of the room-temperature tensile fracture of some ultrahigh-strength steels, and to relate the variation in fracture mode with microstructure. The steels studied were AISI 4340, 300M, and H-11 tempered to a wide range of strength levels. I) EXPERIMENTAL PROCEDURE The compositions of the steels studied are given in Table I. The steel was received in the form of hot-rolled bar stock 5/8 to 1 in. in diameter from which oversized specimens were machined and heat-treated. The heat treatments employed are given in Table 11. Subsequent to heat treatment, the specimens were ground to the final dimensions and stress-relieved by heating for 1 hr at 350°F (with the exception of the as-quenched steel). Standard smooth round specimens of 0.252-in. diameter and 1-in. gage length were tested in a Tinius Olsen Universal Testing Machine using a cross-head speed of 0.025 in. per min. The relatively coarse aspects of the fracture topography were determined by light-microscopic examination of sections through the fracture surface of nickel-plated specimens. A direct carbon-replication technique9 was used in the electron-microscopic study of the fracture surfaces. The replicas were examined in the electron microscope, and stereo pairs of electron micrographs were taken. The stereo pairs were then examined using a Wild ST4 Mirror Stereoscope. Carbide and inclusion particles extracted in the replicas were analyzed by selected-area electron diffraction. II) EXPERIMENTAL RESULTS The mechanical testing data are summarized in Table 111. The values reported are the average of

Jan 1, 1965

By C. R. Barrett, N. N. Singh Deo

The high-temperature steady-state creep behavior of a series of dilute copper-silicon alloys was studied to determine the effect of stacking fault energy on the creep-rate. The steady-state creep rate is, when taken at equivalent diffusivities decreases with decreasing stacking fault energy. The stress and temperature dependencies of is suggest that creep is a difusion controlled dislocation climb process. Electron microscopy studies of the creep substructure revealed: 1) the subgrain size is not a function of the stacking fault energy in these alloys, 2) the dislocation density not attributed to the subgrain walls seems to be higher during primary creep and decreases to a lower steady value during steady-state creep, and 3) the dislocation density during steady-state creep decreases with decreasing stacking fault energy. In the past few years numerous investigators have studied the influence of stacking fault energy on high-temperature creep strength. Most of these investigators have confined their attentions to studying the relationship between steady-state creep rate, is, and stacking fault energy, ?, when samples are tested under conditions of comparable stress and temperature. For the case of fcc metals, it was initially shown by Barrett and Sherbyl and since confirmed by many others2"4 that is decreases with decreasing ?, often following an empirical relation of the form i ?m where m is a constant about equal to 3. The application of theory to explain this observation has not been entirely successful. One of the main difficulties has been the almost complete lack of structural information (dislocation density, subgrain size, and so forth) for samples with different stacking fault energies, tested under high-temperature creep conditions. weertman5 has attempted to explain the stacking fault energy dependence of is on the basis of a dislocation climb mechanism. Assuming that both the rate of dislocation core diffusion and the ease of athermal jog formation decreases as ? decreases Weertman has argued that the rate of dislocation climb and hence the creep rate should also decrease as ? decreases. One questionable aspect of Weertman's analysis is the assumption that core diffusion down extended dislocations is slower than core diffusion down unextended dislocations. The only experimental work done in this area, by Birnbaum et al.6 on nickel and Ni-60 Co, has shown the core diffusivity to increase with decreasing ?. Theories of steady-state creep based on the diffusive motion of jogged screw dislocations often seem unable to predict even the qualitative nature of the es- relationship. Assuming that Weertman is correct in his assumption that the dislocation jog density decreases with decreasing ? then the jogged screw theories predict an increasing dislocation velocity with lower ?. It is usually assumed that the increase in dislocation velocity implies a corresponding increase in creep rate. However, two other factors must be considered before such a statement can be made. That is, we must know how both the mobile dislocation density and the effective stress (the difference between applied stress and internal stress) vary with ?. Significant changes in either one of these factors could outweigh any change in dislocation velocity accompanying a change in ?. And with the slower rates of recovery expected in low stacking fault energy materials it seems likely to expect both mobile dislocation density and effective stress to be dependent on ?. Sherby and Burke7 have suggested that stacking fault energy influences the creep rate in an indirect way. These authors cite evidence that the steady-state subgrain size generated during high-temperature creep is a function of ? decreasing with decreasing ?. Assuming the creep rate to be proportional to the area swept out by each expanding dislocation loop and that subgrain boundaries are good barriers to dislocations, then the creep rate should be proportional to subgrain area, hence increasing as ? increases. A critical evaluation of any of the above theories requires more quantitative information concerning the dislocation substructure generated during high-temperature creep. Accordingly this investigation was undertaken with an aim of studying the influence of stacking fault energy on tbe steady-state creep characteristics of a series of dilute copper-silicon alloys. Special emphasis was placed on studying the strain dependence of both the dislocation configuration and density. MATERIALS AND PROCEDURE Dilute copper-silicon alloys of the compositions shown in Table I were tested in tension at constant stress. The relative stacking fault energy of these alloys has been determined and is shown in Table 11. An Andrade-Chalmers lever arm was used to maintain constant stress and testing was carried out in a water

Jan 1, 1970

By Martha Teach Gnudi, Cyril Stanley Smith

Jan 1, 1942

By A. F. Henderson, C. F. Cornell, A. F. Dunyon, D. A. Dahlstrom

Ossi E. Palasvirta (Development Engineer, Oliver Iron Mining Diu., U. S. Steel Gorp.)—The authors are to be congratulated for their interesting article, which thoroughly illustrates the variables inherent in filtration of taconite concentrate. The work and the conclusions based thereon largely parallel the test work done by the writer at the Pilotac plant" and the experience gained with a commercial size agitating disk filter in the same plant. At Pilotac, however, a thorough study was also made of the effect of depolarizing (demagnetizing) the filter feed, and it is the purpose of this discussion to comment on the merits of depolarization of the magnetite concentrate prior to filtering. The work at Pilotac was done in three phases: 1) preliminary laboratory testing with a circular filter leaf of 0.047 sq ft, followed by 2) plant testing using a 4-ft diam, single-disk agitating filter that was purchased on the basis of the pilot tests on the 4-ft model. In the laboratory tests depolarization was achieved by slowly withdrawing' batches of thickened concentrate from a coil producing an alternating field of about 300 oersteds. In plant tests the standard Pilotac procedure' was employed, wherein the pulp falls freely through the depolarizing coil. The preliminary tests in the laboratory at first seemed to indicate that although depolarization of the filter feed decreases the cake moisture, it also tends to decrease the thickness of the cake, thus decreasing filtering rate. The tests with the 4-ft disk filter soon showed, however, that the compactness of the cake, attained during the form period because of depolarization, permitted a considerable decrease in drying time without any sacrifice in final moisture content. Thus, the filter could be operated at a much higher speed, and the overall capacity was higher than with magnetized feed. Because of the great compactness of the cake there was little shrinkage during the drying period, which prevented cracking and subsequent loss in vacuum. This in turn permitted operation with as thick a feed pulp as the diaphragm pumps could handle, eliminating the necessity of pulp density control. On the basis of these findings, the 6-ft agitating disk filter has been operated at 2 rpm, using feed pulps varying from 65 to 73 pct solids. Initially Saran 601 was used as medium, but it was later replaced with a relatively open, tight-twist nylon cloth. Filtering rates up to 750 lb per ft- er hr can be attained with feeds averaging about 70 pct- 270 mesh, and there is no trouble because of cracking. The cake moistures vary between 8.5 and 9.5 pct. To recapitulate, the merits of depolarizing the filter feed may be summed up as follows: 1) The well dispersed pulp shows less tendency to settle in the filter tank. 2) The homogeneous filter pool results in more even cake formation. 3) Because of absence of flocs, great compactness of cake is attained during the form period. 4) The cake does not tend to crack during the drying period. 5) A drier cake is produced. 6) A shorter drying period is necessary, permitting higher operating speed, which in turn results in increased capacity. 7) Density of the feed pulp can be kept as high as the equipment can handle. This increases capacity, since it is directly proportional to the percentage of solids in the pool. A few tests were also made to study the effect of chemical flocculants on filtration efficiency. Results showed that the effects of chemical and magnetic floc-culation were quite similar. Thus the use of a floccu-lant would impair rather than improve the filtering of magnetite concentrate. A. F. Henderson, C. F. Cornell, A. F. Dunyon and D. A. Dahlstrom (authors' reply)—We want to thank O. E. Palasvirta for his comments, particularly in view of the encouraging results obtained with demagnetized taconite concentrate. In our studies an attempt was made to evaluate the effects of depolarizing the feed to the plant filters by passing the slurry through a coil, similar to the method described by Palasvirta. Unfortunately, in our experiments there were no startling improvements in performance level, neither cake rate increase nor cake moisture reduction. However, when slow filter cycle speeds were employed, the filter cake tended to crack and the vacuum level dropped, resulting in an increase in cake moisture content. When demagnetized feed was used during slow speeds, no cake cracking was evidenced and the vacuum level remained constant. Thus the depolarizing coil was found necessary only in cases of cracking. It should be noted that most of our test work concerned a feed of 85 to 90 pct —335 mesh and about 60 pct by weight solids concentration. This contrasts with 70 pct —270 mesh and 65 to 73 pct by weight solids as noted by Palasvirta. Reviewing both sets of results, it might be concluded that depolarizing may be successfully employed to alleviate cake cracking tendencies and may markedly improve cake rates and moistures on the coarser taconite concentrates. Further investigations may disclose the exact relationship of grind and pulp density to the depolarizing action.

Jan 1, 1959

By J. E. Worthington, W. H. Spence, I. T. Kiff

Gold was discovered at the Haile mine in Lancaster County, South Carolina, in 1827 or 1828, and since that time the mine has been worked intermittently by both open-pit and underground methods until its forced closure in 1942 by World War II. Production figures are incomplete, especially for the early years, but the total gold produced is estimated to have been greater than 200,000 oz. Thus, the Haile mine has been the most productive gold mine in the eastern United States. The upper, residually enriched ores were relatively rich, but the bulk of the production has come from the mining of lower grade ores. General Geology The Haile mine is located in late Precambrian or early Paleozoic rocks of the Carolina slate belt at the edge of the Atlantic Coastal Plain [(Fig. 1)]. The metamorphic grade is lower greenschist facies and the rocks have been folded into a sequence of northeast-trending isoclinal folds. The gold is associated with siliceous, pyritic, and kaolinized felsic pyroclastic and tuffaceous rocks in an interbedded volcanic and volcanoclastic sequence of felsic to mafic tuffaceous rocks and argillaceous sediments [(Fig. 2)]. The ore bodies occur in two northeast trending zones approximately 500 m apart; each zone is 30-70 m wide and 600 m or more in length, with possible extensions to the east beneath the Coastal Plain sediments. Mineralogy. Gold in the Haile mine is always associated with siliceous and/or pyritic ores. The gold occurs in at least three states: As native gold as originally deposited; as residual gold derived from the breakdown of pyrite; and as gold included in pyrite. Major associated minerals in addition to quartz and pyrite are kaolinite, sericite, and iron oxides. Minor molybdenite, arsenopyrite, pyrrhotite, copper sulfides, sphalerite, rutile, and topaz are also present. Petrology. The gold-bearing ore zones vary from highly siliceous rocks to pyritic massive sulfide lenses. This variation is most easily seen today along strike from the Haile pit to the Red Hill pit. Ore grade material still exposed in the wall of the Haile pit consists of a highly siliceous and very thinly bedded rock containing minor pyrite. Along strike, the character of the mineralization changes to pyritic massive sulfide lenses occurring interbedded with siliceous horizons at the Red Hill pit. The siliceous rocks vary from the thinly-bedded material as just described from the Haile pit to silicified fragmental-appearing rocks to totally recrystallized cherty rocks lacking any recognizable primary features. Scattered, apparently at random, throughout the very thinly-bedded and very fine-grained ore face of the Haile pit are seemingly anomalous silica-rich clasts or concretions up to 5 cm in diameter which will be discussed later in this paper. Alteration. One of the most striking features of the Haile deposit is the alteration mineral assemblage which is intimately associated with the siliceous and pyritic ores. This altered material has been intersected in drill core at depths greatly exceeding the modern weathering profile and is, therefore, of hydrothermal origin rather than from supergene processes. This "sericite," actually a fine-grained mixture of sericite, kaolinite, and quartz, can be shown to stratigraphically underlie the gold- quartz-pyrite zone, and is well exposed in the open pit just southeast of the Haile and Bumalo pits. Relict textures indicate that this highly altered material was originally a felsic ash flow. Other similar alteration zones have been found in outcrop and drill core underlying the remaining ore bodies. Thus each of the mineralized zones consists of two parts: A siliceous and/or pyritic gold-bearing ore zone which is stratigraphically underlain by a zone of high alumina minerals, in this case sericite and kaolinite along with variable amounts of quartz. A green chrome mica, presumably fuchsite, is present in trace amounts in the high alumina zone. Genesis An adequate model to explain the origin and distribution of the gold deposits in the Carolina slate belt is presently lacking. Worthington and Kiff1 suggested a volcanogenic origin for certain gold deposits in the North Carolina slate belt from the waning exhalations of felsic volcanic piles. They also pointed out that such an origin has similarities to many epithermal precious metal deposits located in more recent volcanic piles in the western United States. A further key to the understanding of the genesis of the gold mineralization at the Haile mine is the close association of the mineralization in siliceous and sulfidic horizons to the genetically related and stratigraphically underlying high alumina alteration. Such high-alumina alteration is common around felsic volcanic centers in the Carolina slate belt and the mineralogy as seen today consists of some combination of kaolinite, sericite, pyrophyllite, kyanite, andalusite or sillimanite depending on the local prevailing grade of metamorphism. Accompanying the high-alumina alteration are large quantities of pyrite and iron-oxide minerals as well as characteristic minor accessory minerals often including base metal sulfides, fluorine-bearing minerals (topaz, fluorite, apatite), titanium-bearing minerals (ilmenite, rutile),

Jan 1, 1981

[ ]

Jan 1, 1938

By L. W. Bahney

(Cleveland Meeting, October, 1912.) THE photograph, Fig. 1, shows the apparatus a little less than half size, consisting of a filtering-flask fitted with rubber stopper, through which passes a bent glass tube, and an extraction-thimble fitted with rubber stopper through which passes a glass tube of 0.2-5-inch bore. Both tubes are connected by a short piece of rubber tubing. A section of a thimble is shown in the photograph; the tube extends to within in. of the tapered end. The object of using the thimble is to remove the acid from the beaker after all the copper has been precipitated. Time is saved, the copper is not exposed to the acid alone, and there are none of the losses attending ordinary filtration. I have accomplished these results by means of a piece of perforated platinum fastened in the end of a 0.25-in. bore glass tube and a filter-mat of asbestos, but after my supply of proper length fiber became exhausted I could not replenish it even after purchasing 14 lots from four different dealers. The above apparatus may be used to remove at least seven-eighths of a supernatant liquid from a settled precipitate without disturbing the latter. The application of the thimble is best shown by partly out-lining the assay for copper, as follows: Dilute the acid solution of copper and other sulphates to 150 cc. in a 200-cc. Jena beaker, place on a hot plate, add 2 drops of concentrated HC1, then place a strip of aluminum in the beaker (this may be bent or straight, as desired). Connect the apparatus, as shown in Fig. 1, with a filter-pump having a, strong suction. When the copper is precipitated, remove the beaker from tine hot plate and insert the extraction-thimble alongside the strip of aluminum. The acid solution will be drawn through the porous tube. Wish the upper end of the aluminum strip with a jet of hot water, wash down the sides of

Nov 1, 1912

By D. M. Waldorf

Steam permeability measurements have been made in the laboratory on several samples of natural reservoir materials. The steam temperatures and pressures were selected to simulate conditions which might exist in a reservoir during the injection of steam. For each sample tested, the experimental permeability to superheated steam was comparable to that measured with air and no evidence of plugging was detected. Some samples were exposed to water at various temperatures and plugging was found to occur in materials which contained significant quantities of monmorillonite clay. Temperature had little effect on the degree of plug-ning between 75 and 325 F. The measured pemeabilities tended to increase slightly with temperature, but the changes were small compared with the initial loss of per~neability on wetting. Sequential pemzeability measurements were made on two samples using air, water, steam, water and air, in that order. Both samples were water-sensitive and plugged extensively after the initial injection of water. Upon exposure to superheated steatm the samples dehydrated and their permenbilities to superheated steam were comparable to those initially measured with air. The remaining measuretnetzts with water and air confirmed that the water plugging was reversible and that the samples were not seriorrsly damaged during the tests. INTRODUCTION The swelling of water-sensitive clays during water floods has long been recognized as a potential source of reservoir damage. The recent extensive application of steam injection and stimulation has compounded this problem since both hot water and steam (as well as fresh water at reservoir temperatures) are, at sume time, in contact with the producing zone adjacent to the bore of a steam injection well. The purpose of this paper is to present data which compare the sensitivity of some natural sedimentary rock samples to water at various temperatures, and to super-heated steam. Some properties of montmorillonite clay are briefly reviewed, and comparisons are drawn between empirical data and the predicted behavior of the montmorillonite known to be present in the samples. PROPERTIES OF MONTMORILLONIT E CLAY Water initially adsorbs on dry N a -montmorillonite clay in discrete layers in the interlaminar space between clal platelets. The platelet spacing, which is 9.6 A (angstroms) for a dehydrated clay, has been observed to expand in discrete steps to 12.4, 15.5, 18.4 and 21.4 A spacings, indicating the formation of four discrete layers of regularly oriented water molecules.' The first two layers are easily formed by hydrating a dry sample to equilibrium in an atmosphere with carefully controlled humidity. The formation of the higher layers is more difficult. The usual X-ray diffraction patterns of the more highly hydrated samples indicate a gradual increase in the average spacing betwcen 15.5 and 19.2 A, followed by a discontinuous expansion to 31 A when the weight ratio of water to dry clay is between 0.5 and 1.2.' Platelet expansion above 31 A proceeds monotonically as the moisture is increased and no regular arrangement of the platelets ib observed. Water-sensitivity in sedimentary rocks is usually associated with Na-montmorillonite clay when it is in the noncrystal-line state. Mering3 found that the average lattice spacing of sodium montmorillonite hydrated at 68 F and 70 per cent relative humidity was 15.5 A, and that the spacing, at 92 per cent humidity was 16.5 A. The water adsorbed at the higher humidity has the same free energy as liquid water at 65.6 F. Kolaian and Low' used a tensiometer to measure the thermodynamic properties of water in diffuse suspensions of montmorillonite clays relative to pure water. They observed that water in suspensions as dilute as 6 per cent clay became partially oriented when left undisturbed. The bonding associated with this orientation was not extensive because the free energy difference between the water in suspension and pure water was only a few millicalories per mole. They also found that the measured free energy difference decreased rapidly with temperature and became negligible above 100 F. This evidence indicates that montmorillonites contained in sedimentary rocks would dehydrate to a crystalline structure when exposed to superheated steam, and that the rock permeability measured with steam would be equivalent to that measured with air. The effect of elevated temperatures on the swelline of montmorillonite clays in aqueous suspensions has not been investigated. The Gouy-Chapman diffuse-ion-layer theory has been used to predict the swelling pressure of clay suspensions in dilute salt solutions at room temperature with reasonable success. theory also correctly predicts the direction of the thermal response of Na-mont-morillonite swelling pressures in dilute salt suspensions, 9 Over the temperature range of 33 to 68 F, an increase in

Jan 1, 1966

By Wesley G. Josephson

THE MINING PROPERTY of the Argonaut Mining Co., Jackson, Calif., is one of the oldest on the Mother Lode. A vein outcropping on a hill in this section could not long elude the eye of the forty-niner, so it was first discovered in 1850. From that time until 1893 the Pioneer mine, as it was then called, limped along under various poorly equipped and financed operators who tried tapping it by trenching and tunneling. Then the Argonaut Mining Co. took over the property and sank the present 65° inclined shaft in the hanging wall of the vein. The mine workings have now reached the 6000-ft. level, which is 5283 ft. vertically below the surface, or just 3 ft. over a mile. The total production of the mine is uncertain, because of lack of early records, but from 1893 to 1932 it is known to have produced in excess of $17,000,000.

Jan 1, 1932

By Leonard R. Weisberg

The general properties of diffusion in GaAs are reviewed. A total of .fourteen atoms have been studied to date, and activation energies for eleven reported are (in ev): Ga (5.6), As (lo), Zn (2.49), Cd (2.43), Sn (2.5). Mn (2.75). S (4.0). Se (4.2). Ag (0.33), Cu (0.52). and Li (1.0). The dijfusion of the first eight atoms, as measured by Goldstein using radiotracer techniques, established the principle of sub lattice diffusion for both host and impurity atoms, since atoms substituting for gallium have lower activation energies than those substituting for arsenic. The diffusion constant of interstitial copper has been determined for the first time by Hall and Racette using heavily doped p-type samples in which interstitial copper predominates. The anomalous behavior of zinc, which has an abrupt diffusion front and a strong dependence on zinc concentration, has recently been quantitatively explained in terms of an interstitial-substi-tutional equilibrium-diffusion mechanism. Lithium and silver diffuse mainly interstitially, while the diffusion of phosphorus is complicated by the continual formation ofGap. Junction-migration measurements indicate diiferent results than radiotracer techniques, and this is one problem that still remains, together with discrepancies in cadmium-diffusion results, and an unexplained dependence of impurity diffusion on arsenic pressure. BESIDES the usual insights into the behavior of atoms in solids, studies of diffusion in semiconductors have additional importance for device applications. In fact, the amount of diffusion studies performed on a semiconductor might serve as a simple barometer of its technological importance. Thus, the information accumulated for GaAs is not yet quite comparable to that for germanium or silicon, but considerable knowledge is available. The diffusion of at least fourteen atoms has been investigated for GaAs, and the diffusion constants have been determined for eleven of these. Interesting results were found for GaAs that elucidated problems not previously solved for germanium or silicon. For example, the interstitial-diffusion constant for the very fast diffusant, copper, was first measured in GaAs. Also, solutions for interstitial-substitu-tional equilibrium diffusion in extrinsic material were provided first for GaAs, although they are ap- plicable to germanium, silicon, and other semiconductors. Studies in GaAs firmly established the concept of sublattice diffusion, which should have application in many different compound systems. The purpose of this paper is to review briefly the general state of knowledge concerning diffusion in GaAs. First some general aspects of diffusion will be covered, and next attention will be given to the results mentioned above. Diffusion in GaAs has been measured both by radiotracer and junction-penetration techniques, and some discussion will be given of differences in the two sets of results. The comprehensive work of oldsteinl-' has served as the primary reference for the diffusion of well-behaved substitutional atoms in GaAs. Since a review has recently been presented of many of these reults, details of the diffusion data will not be repeated. Neither will any discussion be given of the experimental techniques of diffusion measurements, except to note here, in passing, the simplicity and effectiveness of the precision lapping device employed by Goldstein.' I) EXPERIMENTAL RESULTS AND DISCUSSION A) Summary of Experimental Results. Diffusion constants D = Do exp(E/kT) have been determined for eleven atoms in GaAs: a,' AS,' n,'" Cd,'" n,' n,8 s, e,' Ag,O CU," and i." These results are summarized in Table I. In addition, diffusion was investigated for phosphorus,4'12 germanium,I3 and ilicon,' but Do and E were not determined. Radiotracer techniques were used for most of the studies except for lithium, where a combination of chemical and electrical techniques was employed, and germanium and silicon, where junction-migration techniques were applied. The diffusion of zinc, manganese, sulfur, and tin was also measured using junction migration.13'14 Goldstein demon-

Jan 1, 1964

By John V. Beall

AMONG electrical manufacturers, interest in the outlook for copper supplies has not diminished despite signs of a healthier market following price decontrol. Reason: Electrical utility industry output is expected to grow at an average annual rate of 6 pct for the next 15 years. A more graphic description of the growth ahead is given in the Eighth Quarterly Report of the Director of Defense Mobilization as follows: "Power generating capability, which amounted to 63 million kw at the time of Korea, now stands at more than 81 million. The established goal for installed capability at the end of 1955 is 116 million kw. Orders already on the books of power equipment manufacturers, if fulfilled on schedule, will bring installed capability to over 123 million kw by the end of 1956-and more orders for equipment are yet to come." These statistics portend an impressive requirement for copper, not only for power plants and distribution lines themselves but for the multitude of industry and domestic end-uses.

Jan 4, 1953

By T. W. Watson, D. R. Flynn

,Measurements are reported for the thermal conductivity of four heat-resistant alloys which were measured at the National Bureau of Standards. Data are given for two samples of AISI Type 316 stainless steel covering a combined temperature range from -150° to + 800°C. The thermal conductivities of three samples of AISI Type 347 were measured over the temperature range from -150° to +150C. Thermal conductivity values are given for Carpenter 20 stainless steel from 100" to 800" C. Data are given for Inconel 702, in both the solution-annealed and the age-hardened condition, over the temperature range from -150" to +800C. SINCE 1958 the National Bureau of Standards, at the request of other government agencies or private laboratories, has carried out measurements of the thermal conductivity of a number of metals and alloys. This paper presents available thermal conductivity data obtained in this way on samples of four heat-resistant alloys. The data presented for Carpenter 20* stainless steel are, to the best of our knowledge, the only thermal conductivity values which have been reported for this alloy to date. Although thermal conductivity values for AISI stainless steels 316 and 347 have been reported by previous investigators, the present data are believed to be of particular interest because, for each alloy, the effect on thermal conductivity of small changes in chemical composition can be observed. The data on Inconel 702' are of interest, not only for

Jan 1, 1969

By R. J. Lytle

Geophysical exploration for engineering purposes is conducted to decrease the risk in encountering site uncertainties. Such studies are needed in construction of underground facilities. Current responsibilities, opportunities and challenges for those with geophysical expertise are defined. These include: replacing the squiggly line format, developing verification sites for method evaluations, applying knowledge engineering and assuming responsibility for crucial national problems involving rock mechanics expertise.

Jan 1, 1982

By J. R. Mihalisin, J. S. Iwanski

The response of Inconel "700" to heat treatment has been studied by light and electron microscopy combined with X-ray and electron diffraction techniques. A heat treatment which vesults in low ductility for this alloy appears to be associated with the formation of MC carbide in a Widmanstdtten distribution. This type of precipitation can be suppressed by suitable heat treatment with concurrent increase in ductility. Various other phases precipitated in this alloy are also identified. RECENT studies of commercial nickel base su peralloys have demonstrated the importance of the morphology of carbide phases upon physical properties.' For example, empirical heat treatment studies applied to Nimonic "80" and Inconel "X" have resulted in prescribing double aging treatments for optimum physical properties. These treatments have subsequently been related micro-structurally to grain boundary carbide morphology.2 The purpose of this study was to obtain information about the morphology and identity of some of the phases precipitated in Inconel "700" after heat treatment. It was hoped that some correlation could be made of micro structure with heat treatment similar to that observed with Inconel "X" and Nimonic "80." EXPERIMENTAL PROCEDURE Specimens were obtained from a hot-rolled bar of Inconel "700" of the following composition: C Mn Fe S Si 0.10 0707 0.42 0.007 0.12 Cu Cr -A1 -Ti- Co Mo Ni 0.02 -14.90 TM 2.22 27.61 2.92-- Bal. Specimens were prepared in the following heat-treated conditions: (A) 2275°F for 2 hr WQ (B) 2275°F for 2 hr WQ + 2000°F for 1 hr (C) 2275°F for 2 hr WQ + 1600°F for 48 hr. (D) 2275°F for 2 hr WQ + 2000°F for 1 hr + 1600°F for 48 hr. Empirical stress-rupture studies had shown that treatment (D) resulted in optimum stress-rupture life and ductility. Treatment (C), although giving a good aging response, resulted in low ductility. Treatments (A) and (B), respresenting individual. steps in treatments (C) and (D) were added here for microstructural comparison studies. The procedure was to make an optical and electron microscopic investigation supplemented by X-ray diffraction analysis of electrolytically extracted residues. Electron diffraction studies were made utilizing selected area diffraction techniques with extraction

Jan 1, 1960

By E. William Heinrich

With the mounting emphasis on unconventional energy sources, total consumption of lithium minerals will increase significantly in the next decade. The recent development of the lithium battery, for example, may greatly boost the demand for lithium metal. At the same time, the growth in the ceramic, glass, and chemical industries is bound to increase the demand for lithium minerals. In fact, the entire consumption or utilization breakdown of lithium minerals will change considerably from its current pattern. Briefly, today's market for lithium minerals' can be grouped into three categories: (1) Lithium concentrates. Accounting for 57% of market use, these concentrates are beneficiated Li-A1 silicates for ceramic, glass, and glass-ceramic raw materials. The concentrates are chiefly spodumene; inverted iron-depleted beta-spodumene; and petalite or its isochemical decomposition product spodumene + quartz intergrowth ("squi"). In the past, lepidolite has also been used.

Jan 9, 1974

By Zay Jeffries

THE metallic products of today represent the temporary end point of the efforts and interplay of thousands of years of the human struggle for existence, for pleasure, for conquest, for defense, for improvement in the standard of living, and for the satisfaction of that irrepressible urge to discover and utilize the materials and laws of nature Each metal has gained its place in the sun in severe competition with all other materials, be they metallic or nonmetallic Each serves better than any other for certain purposes. The compromise between cost and properties usually determines the selection of a metallic product for a given use. There are exceptions, as in wartime when the availability at a certain place at a certain time may far outweigh the ordinary economic considerations. In many instances superior properties are vastly more important than cost. If this were not so, the metal industry, for practical purposes, would be the iron industry. The use of 38,000,000 metric tons of newly produced nonferrous metal during, the five-year period from 1940 through 1944 is ample evidence that the special properties of these many metals have great economic value. In fact, our extensive industrial advances would have been quite impossible without the great range and variety of properties and combinations of properties of the nonferrous metals. This observation is not made to detract in the slightest way from the dominant role played by iron and steel. During the past century the production of pig iron has constituted well over 90 per

Jan 1, 1947

After a year-long study comparing existing crafts and techniques for ocean exploration with the future needs of oceanologists, the University of Pennsylvania's ocean engineering research team has come up with a system proposal for prolonged deep-sea exploration. Given the assumption that it will be necessary to re-explore our oceans every 25 years or so, engineers from the University's Towne School of Civil and Mechanical Engineering believe the best sys- tem for future ocean exploration would consist of a stable, manned surface ship operating and controlling two types of vehicles-an unmanned untethered craft for broad search missions, and an unmanned, tethered vehicle for detailed work.

Jan 12, 1969